BARCO AGM19TKI6 LCD Monitor User Manual 17 18 19TK OEM Medical Rev1 p65
Advan Int'l Corp. LCD Monitor 17 18 19TK OEM Medical Rev1 p65
BARCO >
users manual
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 323976 |
| Application ID | h2XGABRAh2gKPqAoZcC9zQ== |
| Document Description | users manual |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 73.39kB (917314 bits) |
| Date Submitted | 2003-05-07 00:00:00 |
| Date Available | 2003-05-07 00:00:00 |
| Creation Date | 2002-09-17 17:52:51 |
| Producing Software | Acrobat Distiller 3.0 for Windows |
| Document Lastmod | 2003-04-17 19:00:12 |
| Document Title | 17_18_19TK(OEM,Medical)Rev1.p65 |
| Document Creator | PageMaker 6.5 |
| Document Author: | alanyu |
AMM17TK/AMM18TK/AMM19TK back of the monitor WARN IN G The title "WARN IN G" is used to inform the users of possible causes that could inflict the injury, death, or property damage to the patients. C AUTIO N The title "C AUTIO N " is used to inform the users of possible causes that could inflict the patients although it might not severe enough to cause deaths. N O TE The title "N O TE" is used to inform the users of items tha t a r e o f imp o r ta nc e in te rms o f ins ta lla tio n, operation, or maintenance of the Equipment although the failure d o es no t inflict the b o d ily harm to the patients. ADAVN INTL CORP.2002 ELO is a Registered trademark of Elo TouchSystems, Inc., All other trademarks are the property of their reference owners. This document is subject to change without notice. Advan provides this information as reference only. Reference to other vendors products does not imply any recommendation or endorsement. Revision Control Date Description Document number FCC Notice NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, user and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment dose cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. The user manual or instruction manual for an intentional or unintentional radiator shall caution the user that changes or modifications not expressly approved by the party responsible for complia nce could void the user’s authority to operate the equipment. 2 Users Guide TABLE OF CONTENTS Quick Setup................................................................................... 3~5 Product Features ... 6 Unpacking .... 7 Symbol Explanations . 8 Regulatory Compliance . 8 EU Declaration of Conformity for Medical Applications ......... 9 Screen Position Adjustment ... 10 Cleaning lnstructions . . 11 Supported Modes ..... 12 Power Management Function 13 Power Management System .. 13 Connecting the Power Cord .. 14 DDC . 14~15 Installation . 14~15 Installation for Video Play Back.......................................................16 User Controls ... 17 Basic OSD Operation (VGA) ... 18~20 Basic OSD Screen Section (C-Video or S-Video). ... 21~23 OSD Function Description (VGA) 24 OSD Function Description (C-Video or S-Video)...... ..... 25 Troubleshooting 26 Specification of AMM17TK......................................................... 27 Specification of AMM18TK......................................................... 28 Specification of AMM19TK......................................................... 29 Connectors ... 30 Description of Warranty 31~32 Tounchscreen Users Manual ... 33~34 AMM17TK/AMM18TK/AMM19TK Quick Setup (IBM/IBM Compatible under Windows 95/98/ME/2000) Please Read Carefully When Setting Up Your New Monitor AGM17TK/AGM18TK/AGM19TK Monitor Screen Adjustment and Resolution Setting Procedure for IBM/IBM Compatible Computers with Windows based OS system. Before adjusting the monitor, all the necessary drivers should be installed to your System and resolution has to be set to manufacturers recommended preset of 1280 x 1024 @ 60Hz, 70Hz, 72Hz or 75 Hz. To check the resolution, press the SELECT UP button on the monitor and the Information will display under the OSD. Information will have Resolution, Horizontal and Vertical (Refresh rate) frequency information. To change the resolution to its factory recommended preset. 1. On a Windows 95, 98, ME or 2000, press right button on a Mouse to execute the Pop-up menu. 2. Press Properties to execute the Display Properties 3. Press Setting and change the resolution to 1280 x 1024. 4. Press Apply or OK to select and press OK to keep the selected resolution. 5. Go back to Display Properties - Setting - Advanced properties - Adapter 6. On Adapter property, change the refresh rate to 60Hz, 70Hz, 72Hz or 75Hz. If you dont have these options, choose Adapter Default. (60Hz recommended) Screen Adjustment Procedure 1. Press the AUTO button. 2. If you still dont have a clear display monitor, please refer to step 3. 3. Start Shut Down in Windows 95/98/ME/2000 - It will display moire on screen 4. Press Up or Down button then the OSD menu will pop-up. 5. Adjust the Frequency under the OSD to reduce or get rid of the vertical display noise (Jail bars). (Page 16) 6. Once the vertical display noise disappears, press adjust the Phase to reduce or get rid of the horizontal display noise (Snowy effect). (Page 16) 4 Users Guide Quick Setup (IBM/IBM Compatible under Windows NT 4.0) Please Read Carefully When Setting Up Your New Monitor AGM17TK/AGM18TK/AGM19TK Monitor Screen Adjustment and Resolution Setting Procedure for IBM/IBM Compatible Computers with Windows based OS system. Before adjusting the monitor, all the necessary drivers should be installed to your System and resolution has to be set to manufactures recommended preset of 1280 x 1024 @ 60Hz, 70Hz, 72Hz or 75Hz. To check the resolution, press the SELECT UP button on the monitor and the Information will display under the OSD. Information will have Resolution, Horizontal and Vertical (Refresh rate) frequency information. To change the resolution to its factory recommended preset. 1. 2. 3. 4. On a Windows NT 4.0, press right button on a Mouse to execute the Pop-up menu. Press Properties to execute the Display Properties Press Setting and change the resolution to 1280 x 1024. Change Refresh Frequency to 60Hz, 70Hz, 72Hz or 75Hz. (60Hz recommended) Screen Adjustment Procedure 1. Press the AUTO button. 2. If you still dont have a clear display monitor, please refer to step 3. 3. Start Shut Down in Windows 95/98/ME/2000 - It will display moire on screen 4. Press Up or Down button then the OSD menu will pop-up. 5. Adjust the Frequency under the OSD to reduce or get rid of the vertical display noise (Jail bars). (Page 16) 6. Once the vertical display noise disappears, press adjust the Phase to reduce or get rid of the horizontal display noise (Snowy effect). (Page 16) AMM17TK/AMM18TK/AMM19TK Quick Setup (Macintosh) Please Read Carefully When Setting Up Your New Monitor 1. Set your Macintosh Adapter on pages 23 and 24. 2. Push the APPLE icon on the upper left corn and execute Control Panel-> Monitors&Sound. Select Thousands for the Color Depth, Select 1280X1024, 60Hz, 70Hz, 72Hz or 75Hz for the Resolution. (60Hz recommended) * On some Apple G3 or newer systems, you may not need to use the Macintosh Adapter. Screen Adjustment Procedure 1. Press the AUTO button on the monitor. 6 Users Guide INTRODUCTION Congratulations on your purchasing of the AMM17TK/AMM18TK/AMM19TK high performance TFT LCD monitor. FEATURES The AGM17TK/AGM18TK/AGM19TK is a TFT-LCD monitor that is intelligent, microprocessorbased and ergonomically designed display, compatible with most analog RGB (Red, Green, Blue) display standards, including PS/V, PS/2, Apple Macintosh Centris, Quadra, and Macintosh II family signals. The LCD monitor is capable of displaying crisp and vibrant color graphics with VGA, SVGA, XGA, SXGA (non-interlaced), and most Macintosh compatible color video cards. • Advanced Viewing Solution (AVS): Our sophisticated filter extends the viewing angle of the screen image, without sacrificing contrast ratio and brightness. • Advanced Timing Setup (ATS): A unique technology from the One Touch Auto Adjustment. Pressing the Auto Adjust button on the front panel, automatically optimizes position, phase, clock, contrast and color balance. This allows the user to maximize the perfect screen setting in the shortest amount of time. • Advanced Mounting Solution (AMS): Improve flat panel environment, utilizing numerous ergonomic mounting solutions to allow creative use in conjunction to product application. • The monitor is able to properly function even in case of upgrade video cards or software because of the wide auto-scanning compatibility range without requiring to buy a new monitor. • The internal microprocessor digitally controls auto-scanning. For horizontal scan frequencies between 24.8 KHz and 60.2 KHz, and vertical scan frequencies between 56.3 Hz and 85.1 Hz. In each frequency mode, the microprocessor-based circuitry allows the monitor to function at the precision-of a fixed frequency. • The resident memory allows for storing factory default settings and also additional user adjustment parameters. • The maximum resolution achievable is SXGA (1280 x 1024), best suited for Windows applications • The compact and sleek cabinet design saves lot of your desk space and makes your desk look neat and tidy. • The monitor is compliant with VESA-DPMS power management standard. In order to save energy, the monitor must be connected to a system compliant with the standard. • The monitor is also compliant with the most stringent environmental scheme of TCO 95. In this scheme, no environmental harmful substances are used during the entire manufacturing process. The monitor is certified by UL International to medical standard UL2601-1. It is also CE marked for sale into the European Community for integration or use with medical products. It is certified by NEMKO according to EN60601-1 & EN60601-1-2 for sale to the medical market. AMM17TK/AMM18TK/AMM19TK UNPACKING Please check the following items are present when you unpack the box, and save the packing materials in case you will need to ship or transport the monitor in future. • AMM17TK/AMM18TK/AMM19TK LCD Monitor and two video cable (1) VGA HDDB15 cable (1) DVI-D cable AUTO SELECT • AC Power cord • AC-Adapter CAUTION Manufacturer : Ault Korea Model No : MW160 or MW116 • Floppy Disk (for test pattern and set up) • User Manual, Registration Card, and Warranty Card 5(* ,675 $7,2 • $17< :$55 C-video(Composite Video) Cable, S-Video Cable, Audio Cable and USB Cable 8 User TMs Guide Symbol Explanations Indicates proof of conformity to applicable European Economic Community Council directives and to harmonized standards published in the official journal of the European Communities Tested and certified by UL to UL2601. If this mark appears with the indicators "C" and "US" the product is certified for both the U.S and Canadian markets, to the applicable U.S and Canadian standards. Tested to comply with FCC Class B standards. Dangerous high voltage. Consult accompanying documents. Tested and certified by NEMKO in accordance with EN60601-1. Indicates protective earth ground. For indoor use only. DC power control switch Regulatory Compliance This monitor has been tested to comply with IEC/EN 60601-1 and IEC/EN60601-1-2. Only model AGM19TK is classified according to UL2601-1 and CAN/CSA C22.2 No.601-1. Because many medical offices are located in residential areas, this monitor, in addition to the medical requirements, has also been tested and found to comply with the limits for FCC Class B computing devices in a typically configured system. It is the system integrator or configurer's responsibility to test and ensure that the entire system complies with applicable EMC laws. 8.1 User TMs Guide Equipment is not suitable for use in the presence of flammable anesthetic mixture with air or with oxygen or nitrous oxide. No user serviceable parts inside, ask qualified personnel when accessing inside. For disposal of waste product, you must follow the requirement of local code. Electrical input rating : 12V d.c 4.5A Classification - Type of protection against electric shock : Class I Equipment. - Degree of protection against the ingress of water : Ordinary - Mode of operation : Continuous Environmental conditions for transport and storage - Temperature range within 20℃ to 60℃ - Relative humidity range 10% to 90% - Atmospheric pressure range within 500 to 1060hPa. Manufacture information : CARDIANAL INC. 205 Ace Techno Tower, 197-17 Kuro-Dong, Kuro-Gu, Seoul 152-050 Korea Additional explanation of symbol : Direct Current This device is complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may caus e This monitor is intended for use on Health Care Facilities. Only the model AMM17TK, AGM19TK, AMM19TK and 240-030-900 Cleaning : Do not try to clean the LCD Monitor with a liquid or chemicals. AMM17TK/AMM18TK/AMM19TK EU Declaration of Conformity for Medical Applications A Declaration of Conformity has been filed for this product. A sample of this document may be found in the addendum which accompanied this manual. For a copy of the Declaration of Conformity document, please contact ADVAN Intl Corp. and request for AMM17TK, AGMM18TK and AMM19TK DOC. Installation Before you unpack your monitor, prepare a suitable workspace. You need a stable and level surface near a grounded wall outlet in an area which is relatively free of glare from sunlight or other sources of bright light. The monitor is cooled by natural convection (it has no fan). For optimum performance, do not block the cooling vents. While unpacking the monitor, inspect it and other package contents for shipping damage that could cause a fire or shock hazard. Immediately report any shipping damage to the carrier or transportation company and contact customer service for monitor in the future or in case of return. After you unpack the monitor, make sure the following items are included Monitor with 1.5 meter(5ft)monitor-to computer video cable AC adapter with cable CAUTION: AC Adapter must be plugged into Grounded a power outlet) CAUTION : AC adapter Manufacturer: Ault korea Model No: MW160 or MW116 Touchscreen cable if monitor has touchscreen option This operations manual Note: Your system provider may offer alternative cords or cables depending on the installation requirement and local geography issues. 10 Users Guide SCREEN POSITION ADJUSTMENT In order to optimize the best viewing position, you can adjust the tilt of the monitor by using both of your hands to hold the edges of the monitor as shown in the figure below. The monitor can be adjusted to 28 degrees up as indicated by arrow below. 28° SAFETY PRECAUTION • • • • • • AMM17TK/AMM18TK/AMM19TK 11 Avoid placing the monitor, or any other heavy object, on the power cord to prevent fire or electrical shock from damage to the power cord. Do not expose the monitor to rain, excessive moisture, or dust to avoid fire or shock hazard. Do not cover the slots or openings of the monitor for proper heat dissipation. Always put the monitor in a place where there is adequate ventilation. Avoid placing the monitor against a bright background or where sunlight or other light sources may reflect on the area of the monitor. Place the monitor just below eye level. Handle with care when transporting the monitor. Refrain from giving the shock or scratch to the screen, as screen is fragile. 12 User ’s Guide PRESET MODES To reduce the need for adjustment for different modes, the monitor has default setting modes that are most commonly used as given in the table below. If any these display modes are detected, the monitor automatically adjusts the picture size and centering. When none of the mode is matched, the user can store their preferred modes in the user modes. The monitor is capable of storing up to 7 user modes. The only condition to store as a user mode is the new display information must 1 KHz difference for horizontal frequency or 1 Hz for vertical frequency or the sync signal polarities are different from the de fault modes. Mode 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 Resolution (H×V) 640 ×350 640 ×350 640 ×400 640 ×400 720 ×350 720 ×400 720 ×400 640 ×480 640 ×480 640 ×480 640 ×480 800 ×600 800 ×600 800 ×600 800 ×600 800 ×600 1024 ×768 1024 ×768 1024 ×768 1024 ×768 1024 ×768 1152 ×864 1280 ×960 1280 ×1024 1280 ×1024 H. Freq. (KHz) V. Freq. (Hz) Clock Freq. (MHz) 31.5 37.9 31.5 37.9 31.5 31.5 37.9 31.5 37.9 37.5 43.3 35.1 37.9 48.1 46.9 53.7 35.5 48.4 56.5 60 68.7 67.5 60 63.9 79 70 85 70 85 70 70 85 60 72 75 85 56 60 72 75 85 43 60 70 75 85 75 60 60 75 25.175 31.5 25.175 31.5 28.322 25.175 35.5 25.175 31.5 31.5 36.0 36.0 40.0 50.0 49.5 56.25 44.9 65.0 75.0 78.75 94.5 108.0 108.0 135.0 157.5 AMM17TK/AMM18TK/AMM19TK POWER MANAGEMENT FUNCTION 13 The monitor is equipped with the power management function which automatically reduce the power consumption when not in use in three power level modes. • Stand-by Mode The monitor goes into stand-by mode when the horizontal sync signal is off for about 10 seconds. In this mode, the screen goes off and the power LED blinks for 3 seconds On and 1 second Off. The screen is displayed after the horizontal sync signal is restored. • Suspend Mode The monitor goes into suspend mode when the vertical sync signal is off for about 10 seconds. The power consumption during this is less than 8 W. In this mode, the screen goes off and the power LED blinks for 3 seconds On and 1 second Off. The screen is displayed after the vertical sync signal is restored. • Off Mode The monitor goes into power-off mode when the vertical and horizontal sync signals are off for about 10 seconds. In this mode, the screen goes off and the power LED blinks for 3 seconds On and 1 second Off. The screen is displayed after the vertical and horizontal sync signals are restored. Power Management System The AMM17TK/18TK/19TK Series Medical Monitor complies with the VESA DPMS power management proposal. The VESA DPMS proposal provides four phases of power-saving modes by detecting the horizontal sync signal as shown in the table blow. M o de D C Input P o we r (m o nito r o nly ) A C Input po we r (Inc l. A C a da pte r) L E D Sta tus On 3 5 W ma x. 6 0 W m a x. S te a d y G re e n S ta nd b y 4 .5 W m a x. 6 W m a x. B link ing G re e n S up e nd 4 .5 W m a x. 6 W m a x. B link ing G re e n On 4 .5 W m a x. 6 W m a x. B link ing G re e n When the monitor is power saving mode or detects an incorrect timing, the screen will be blank and power LED indicator will blink. 14 Users Guide DDC To make your installation easier, the monitor is able to Plug and Play with your system if your system also supports DDC protocol. The DDC (Display Data Channel) is a communication protocol through which the monitor automatically informs the host system about its capabilities, for example, supported resolutions and corresponding timing. The monitor supports DDC1 and DDC2B standard. INSTALLATION To install the monitor to your host system, please follow the steps as given below: Steps 1. Use the VGA cable that provides D-SUB 15P connector and connect to the 15-pin connector on the VGA controller card. 2. Connect the DC power to the DC power connector on the monitor. 3. If use with USB hub, connect the loop cable between the monitor and the USB hub then connect the DC power to the bottom of USB hub. 4. Connect one end of AC power cord into the AC Adapter and the other end to AC power outlet. (See page 13) 5. Then turn the computer on and then the monitor. 6. If the monitor still does not function properly, please refer to the troubleshooting section to diagnose the problem. USB DC loop cable S-Video cable C-Video cable Analog signal cable Digital signal cable (DVI) USB cable from monitor to PC DDC AMM17TK/AMM18TK/AMM19TK 15 To make your installation easier, the monitor is able to Plug and Play with your system if your system also supports DDC protocol. The DDC (Display Data Channel) is a communication protocol through which the monitor automatically informs the host system about its capabilities, for example, supported resolutions and corresponding timing. The monitor supports DDC1 and DDC2B standard. Installation with sound board or sound source To install the monitor for input/output sound, please follow the steps as given below: Steps 1. Connect sound source (ex. sound output from sound card, sound output from CD player or DVD player, etc.) to Audio In. 2. Connect sound source receiver (ex. sound input or Mic input from the sound card) to Mic out. 3. At the front of the monitor there are two connection, Audio Out and Mic In. Connect any type of sound output device (ex. speaker, earphone, etc.) to Audio Out. Mic In is for microphone input connection. Audio Out Mic In Audio in cable Mic out cable AC power adapter 16 Users Guide Display for Video and Image Playback Explains how to use our AGM17TK/AGM18TK to play VCR, view television, video game, or digital camera images. It also show you how to connect video and other types of video equipment to the display. Connecting with Video Equipment You can connect many types of video equipment to the display. The equipment must have either Super VHS video (S-video) ports or composite video ports. To install the monitor to your video equipment, please follow the steps as given below: Steps 1. Make sure the video equipment has a Super VHS (S-video) or a Composite video connector. 2. Turn off the computer, display, and video equipment before any types of connection. 3. For composite video, plug one end of an RCA cable into the video out port on the video equipment then connect the other end to the monitor video input port. 4. For S-video, plug one end of the S-video cable into the video out port on the video equipment then connect the other end to the monitor S-video input port. 5. Connect the DC power to the DC power connector on the monitor. 6. Connect one end of AC power cord into the AC Adapter and the other end to AC power outlet. 7. Then turn the video equipment on and then the monitor. Connecting to a Television Signal The display doesnt have a tuner. To view television on the display, you need to use either the VCR or TV tuner card in your computer to change channels. Video and Sound This monitor does have speakers for sound. If youre using the display to play a video or view television images, you need to connect the speakers to your television or video equipment for sound. Please review page 13 for sound connection. USB DC loop cable S-Video cable C-Video cable Analog signal cable Digital signal cable (DVI) USB cable from monitor to PC AMM17TK/AMM18TK/AMM19TK 17 USER CONTROLS Front Panel Controls 1. Power LED: Lights up to indicate the power is turned ON. 2. Power Switch: To turn ON or OFF the power. 3. +: To increase the value of the parameter in the OSD you have selected for adjustment. To increase the brightness directly when OSD menu is not activated. 4. -: To decrease the value of the parameter in the OSD you have selected for adjustment. To increase the brightness directly when OSD menu is not activated. 5. Select Up: To enter OSD menu then can use as moving upward in the OSD menu. 6. Select Down: To move downward in the OSD menu. Switch PC display to Video display and vice versa by one touch when OSD menu is not activated. 7. Auto Button: One touch Auto adjust or Exit OSD menu. Standard OSD Operation 1. Press menu button to activate the OSD. 2. Use Select Up or Down keys to move up or down through the menu. The parameter will be highlighted wehn selected. 3. Then use + or - to increase or decrease the value of the parameter, or make selection between different options. 4. To quit the OSD screen at any time during the operation, press Auto button. If no keys are pressed for a time period, the OSD automatically disappears. 18 Users Guide OSD Scren Basic Section (VGA) For OSD display, push Menu. For selecting Icon, push Up or Down Push the select button to execute the Auto Setup function Push Up or Down button to select between Brightness or Contrast then push Select Use Left or Right button to adjust Push Up or Down button to select between Frequency or Phase then push Select Use Left or Right button to adjust Push Up or Down button to select between Horizontal or Vertical then push Select Use Left or Right button to adjust Push Up or Down button to select between Push Left or Right to select Color Temp between 5000, 6500, 7300, 9500, or User then push OSD Hor. Pos., OSD Ver. Pos., OSD Background, or User Timeout then push Select Select If User were slected, push Up or Down button to Use Left or Right button to adjust select between Red, Green, or Blue then push Select Use Left or Right button to adjust AMM17TK/AMM18TK/AMM19TK OSD Scren Basic Section (VGA) 19 For OSD display, push Menu. For selecting Icon, push Up or Down Push Up or Down button to select between DPMS, Auto Source Select, Freeze Frame, or ADC Calibration then push Select Use Left or Right button to adjust Push the select button to execute the Zoom function Push the select button Use Left or Right button to adjust Push the select button Use Left or Right button to adjust Push Up or Down button to select between 640 Push Up or Down button to select between Mode or 720 Mode Analog RGB, Digital RGB, Composite Video or Use Left or Right to choose the correct mode then Super Video push Select button Use Left or Right to choose the correct mode then push Select button 20 Users Guide OSD Scren Basic Section (VGA) For OSD display, push Menu. For selecting Icon, push Up or Down Push the select button to execute Recall Factory Default Push the select button to execute Information AMM17TK/AMM18TK/AMM19TK OSD Scren Basic Section (C-Video or S-Video) 21 For OSD display, push Menu. For selecting Icon, push Up or Down Push Select button Push Left or Right button to adjust Push Select button Push Left or Right button to adjust Push Up or Down button to select between Brightness or Contrast then push Select Use Left or Right button to adjust Push Up or Down button to select between Horizontal or Vertical then push Select Use Left or Right button to adjust Push Up or Down button to select between Push Left or Right to select Color Temp between 5000, 6500, 7300, 9500, or User then push OSD Hor. Pos., OSD Ver. Pos., OSD Background, or User Timeout then push SelectSelect If User were slected, push Up or Down button to Use Left or Right button to adjust select between Red, Green, or Blue then push Select Use Left or Right button to adjust 22 Users Guide OSD Scren Basic Section (C-Video or S-Video) For OSD display, push Menu. For selecting Icon, push Up or Down Push Up or Down button to select between Push the select button DPMS, Auto Source Select, Freeze Frame, or Use Left or Right button to adjust ADC Calibration then push Select Use Left or Right button to adjust Push the select button Use Left or Right button to adjust Push the select button Use Left or Right button to adjust Push the select button Use Left or Right button to adjust Push Up or Down button to select between Analog RGB, Digital RGB, Composite Video or Super Video Use Left or Right to choose the correct mode then push Select button AMM17TK/AMM18TK/AMM19TK OSD Scren Basic Section (C-Video or S-Video) 23 For OSD display, push Menu. For selecting Icon, push Up or Down Push the select button to execute Recall Factory Default Push the select button to execute Information 24 Users Guide OSD Function Description (Under VGA Display) It e m F u n c t io n D e s c r ip t io n A uto A d j us t T he A uto - A d j us t w i l l a uto ma ti c a l l y a d j us t V- P o s i ti o n, H P o s i ti o n, C l o c k, C l o c k- P ha s e , a nd C o ntr a s t, the w ho l e p r o c e s s ta ke s a b o ut 5 s e c o nd s . ( P l e a s e us e the te s t p a tte r n f i l e i n the a tta c he d LC D mo ni to r uti l i ty d i s k f o r A uto A d j us t) . B r i ghtne s s To i nc r e a s e o r d e c r e a s e the b r i ghtne s s . C o ntr a s t To i nc r e a s e o r d e c r e a s e the c o ntr a s t. B l a c k Le v e l To i nc r e a s e o r d e c r e a s e the b l a c k l e v e l . F r e q ue nc y To a d j us t f r e q ue nc y ( d o t c l o c k) . P ha s e To a d j us t p ha s e ( c l o c k- p ha s e ) . H o r i zo nta l To mo v e the s c r e e n l e f t o r r i ght. Ve r ti c a l To mo v e the s c r e e n up w a r d o r d o w nw a r d . OS D Ho r Po s To mo v e O S D me nu l e f t o r r i ght. O S D Ve r P o s To mo v e O S D me nu up w a r d o r d o w nw a r d . O S D B a c kgr o und C ho o s e b e tw e e n O p a q ue o r Tr a ns l uc e nt. Us e r Ti me o ut S e t O S D s c r e e n a p p e a r i ng ti me . C o l o r Te mp C ho o s e b e tw e e n 5 0 0 0 , 6 5 0 0 , 7 3 0 0 , 9 5 0 0 , o r Us e r f o r c o l o r te mp . Re d B a l a nc e R e d . Gr e e n B a l a nc e G r e e n. B l ue B a l a nc e B l ue . D P MS E na b l e o r D i s a b l e D P MS . A uto S o ur c e Se l e c t A d j us t a uto s o ur c e s e l e c t b e tw e e n o f f , l o w , o r hi ght. F r e e ze F r a me E na b l e o r D i s a b l e f r e e ze f r a me A D C C a l i b r a ti o n Zo o m E na b l e zo o m- i n f unc ti o n Ima ge S ha r p ne s s S e t i ma ge s ha r p ne s s f r o m 1 to 5 . S c a l e Mo d e C ho o s e s c a l e mo d e b e tw e e n f i l l s c r e e n, a s p e c t r a ti o , o r o ne to o ne D O S Mo d e S e t d i s p l a y und e r D O S mo d e a t 6 4 0 o r 7 2 0 . Inp ut S o ur c e Se l e c t C ho o s e i np ut s o ur c e b e tw e e n a na l o g R G B , d i gi ta l R G B , c o mp o s i te v i d e o , o r s up e r v i d e o R e c a l l F a c to r y D e f a ul t S e t to f a c to r y d e f a ul t. Inf o ma ti o n D i s p l a y i nf o r ma ti o n o n r e s o l uti o n, r e f r e s h r a te , a nd i np ut mo d e . AMM17TK/AMM18TK/AMM19TK 25 OSD Function Description (Under C-Video or S-Video Display) It e m F u n c t io n D e s c r ip t io n H ue To i nc r e a s e o r d e c r e a s e the hue l e v e l . S a tur a ti o n To i nc r e a s e o r d e c r e a s e the s a tur a ti o n l e v e l . B r i ghtne s s To i nc r e a s e o r d e c r e a s e the b r i ghtne s s . C o ntr a s t To i nc r e a s e o r d e c r e a s e the c o ntr a s t. B l a c k Le v e l To i nc r e a s e o r d e c r e a s e the b l a c k l e v e l . H o r i zo nta l To mo v e the s c r e e n l e f t o r r i ght. Ve r ti c a l To mo v e the s c r e e n up w a r d o r d o w nw a r d . OS D Ho r Po s To mo v e O S D me nu l e f t o r r i ght. O S D Ve r Po s To mo v e O S D me nu up w a r d o r d o w nw a r d . O S D B a c kgr o und C ho o s e b e tw e e n O p a q ue o r Tr a ns l uc e nt. Us e r Ti me o ut S e t O S D s c r e e n a p p e a r i ng ti me . C o l o r Te mp C ho o s e b e tw e e n 5 0 0 0 , 6 5 0 0 , 7 3 0 0 , 9 5 0 0 , o r Us e r f o r c o l o r te mp . Re d B a l a nc e R e d . Gr e e n B a l a nc e G r e e n. B l ue B a l a nc e B l ue . D P MS E na b l e o r D i s a b l e D PMS . A uto S o ur c e Se l e c t A d j us t a uto s o ur c e s e l e c t b e tw e e n o f f , l o w , o r hi ght. F r e e ze F r a me E na b l e o r D i s a b l e f r e e ze f r a me . A D C C a l i b r a ti o n Zo o m E na b l e zo o m- i n f unc ti o n. Ima ge S ha r p ne s s S e t i ma ge s ha r p ne s s f r o m 1 to 5 . Vi d e o S c a l e Mo d e C ho o s e v i d e o s c a l e mo d e b e tw e e n no r ma l , 4 : 3 s c a l e mo d e , o r 1 6 : 9 s c a l e mo d e . Vi d e o S ha r p ne s s To i nc r e a s e o r d e c r e a s e the v i d e o s ha r p ne s s . Inp ut S o ur c e Se l e c t C ho o s e i np ut s o ur c e b e tw e e n a na l o g R G B , d i gi ta l R G B , c o mp o s i te v i d e o , o r s up e r v i d e o R e c a l l F a c to r y D e f a ul t S e t to f a c to r y d e f a ul t. Inf o ma ti o n D i s p l a y i nf o r ma ti o n o n r e s o l uti o n, r e f r e s h r a te , a nd i np ut mo d e . 26 Users Guide TROUBLESHOOTING Before sending your LCD monitor for servicing, please check the troubleshooting list below to see if you can self-diagnose the problem. Pr oble ms C ur r e nt St a t us R e me dy LED ON • Using OSD, adjust brightness and contrast to maximum or reset to their default settings. LED OFF • Check the pow er sw itch. • Check if AC pow er cord is properly connected to the AC adapter. • Check if video signal cable is properly connected at the back of monitor. • Check if the pow er to computer system is ON. Unstable Picture • Check if the specification of graphics adapter and monitor is in compliance w hich may be causing the input signal frequency mismatch. Display is missing, center shift, or too small or too large in display size • Using Auto Setup button, if still display abnormal picture then adjust CLOCK, CLOCK-PHASE, H-POSITION and VPOSITION w ith non-standard signals. • Using OSD, in case of missing full-screen image, please select other resolution in your Operating System (Window s 95/98, NT) or other vertical refresh timing. • Must w ait for a few seconds after adjusting the size of the image before changing or disconnecting the signal or pow ering OFF the monitor. No Picture LED Blinking Abnormal Picture AMM17TK/AMM18TK/AMM19TK SPECIFICATION 27 AM M 17TK LC D P ane l 4 4 . 2 c m / 1 7 . 4 - in c h C o lo r T F T P a n e l Ty p e A c tiv e M a t r ix R e s o lu t io n 1 2 8 0 d o t s x 1 0 2 4 lin e s ( R e c o m m e n d e d ) P ix e l P it c h 0 .2 7 m m D is p la y C o lo r 1 6 m illio n c o lo r s R e s p o n s e Tim e 25ms C o lo r T o n e U p to 2 5 6 to n e C o lo r F ilt e r R G B v e r t ic a l s t r ip e t y p e F a c e F in is h in g A n ti- G la r e H a r d C o a t e d V ie w in g A n g le 1 6 0 ° H 1 6 0 ° V (C R > = 1 0 ) V id e o 0 .7 V p - p a n a lo g R G B & T M D S ( P a n e lL in k ) D ig it a l 165 M H z x 1 I n p u t S ig n a l S y nc 2 .5 ~ 5 . 0 V p - p s e p a r a t e d s y n c I n p u t I m p e d a n c e ( A n a lo g ) V id e o - 7 5 O h m S y nc - 1 k O h m C o m p o s it e S y n c C - V id e o , S - V id e o D ig it a l 3 c h a n n e l T M D S r e c e iv e r, s in g le p ix e l 2 4 b it M S B a lig n e d R G B T F T S c a n n i n g F re q u e n c y H o r izo n t a l 30~ 68kH z Ve r t ic a l 5 6 ~ 8 5 H z ( U P t o 8 5 H z a t 1 0 2 4 x 7 6 8 m o d e a n d u p to 7 5 H z at 12 8 0 x 1 0 2 4) D i s p l a y S i ze H x V 1 3 .6 " x 1 0 . 9 " ( 3 4 5 .0 m m x 2 7 6 . 4 8 m m ) B ri g h t n e s s , C o n t ra s t R a d t io , G ra y S c a l e s B r ig h t n e s s 2 2 0 c d / m 2 , S ta n d a r d C o n tra s t R a tio 4 0 0 :1 T y p . G r a y S c a le s U p to 2 5 6 s te p s S ig n a l I n p u t C o n n e c t o r V id e o D B 9 - 1 5 p in , D ig it a l D V I , N T S C , S - V id e o To u c h sc re e n R S - 2 3 2 D B - 9 ( O p t io n a l) T e m p e ra t u re E n v i ro n m e n t O p e r a t in g Te m p e r a t u r e 3 2 ° ~ 1 0 4 °F (0 ° - 3 5 °C ) S t o r a g e Te m p e r a t u r e - 4 ° ~ 1 4 0 °F (2 0 ° - 6 0 °C ) H u m id it y 1 0 ~ 9 0 % R H ( w it h o u t c o n d e n s a t io n ) P o w e r S o urce D is p la y M o n it o r DC 12V A C - A d a p te r A C 1 0 0 ~ 2 4 0 V 6 0 W ( W it h o u t o p t io n , N o r m a l O p e r a t io n ) R e g u la t io n s S a fe t y a n d E M C U L / c U L , F C C , C E , T C O 9 9 , E n e r g y S ta r, C B , M P R II, E R G /G S .V C C I, U L 2 6 0 1 - 1 , E N 6 0 6 0 1 - 1 C a b in e t D e s k to p S ta nd 1 7 . 5 in c h ( W ) x 1 7 . 8 in c h ( H ) x 9 . 5 in c h ( D ) 4 5 0 m m (W ) x 4 5 5 m m (H ) x 2 4 5 m m (D ) F r e e M o u nt 1 7 . 5 in c h ( W ) x 1 4 . 2 5 in c h ( H ) x 3 in c h ( D ) 4 5 0 m m (W ) x 3 6 2 m m (H ) x 7 6 m m ( D ) W e ig h t D e s k to p S ta nd 2 0 . 6 lb . ( 9 .3 K g ) F r e e M o u nt 1 6 lb . ( 7 . 3 K g ) T ilt B a s e 5° Down 30° Up S t e r e o s p e a k e r, U S B ( R e v 1 . 0 ) O p t i o n a l M o d u le To u c h P a n e l * All contents are subject to change without notice. * Touch Screen Model doesnt include the Video-in (C-Video, S-Video) function. * Surface Wave Touchscreen model AMM17TK/18TK/19TK-TEW and Resistive Touchscreen model AMM17TK/18TK/19TK-TE 28 Users Guide SPECIFICATION A M M 18TK LC D P ane l 4 6 c m /1 8 . 1 - in c h C o lo r T F T P a n e Ty p e A c tiv e M a tr ix R e s o lu tio n 1 2 8 0 d o ts x 1 0 2 4 line s ( R e c o m m e n d e d ) P ix e l P itc h 0 .2 8 m m D is p la y C o lo r 1 6 m illio n c o lo r s R e s p o n s e Tim e 40ms C o lo r To n e U p to 2 5 6 to n e C o lo r F ilte r R G B v e r tic a l s tr ip e typ e F a c e F in is hin g A n ti- G la r e H a r d C o a te d V ie w in g A n gle 1 6 0 ° H 1 6 0 ° V (C R > = 1 0 ) V id e o 0 .7 V p - p a n a lo g R G B & T M D S ( P a ne lL in k ) D ig ita l 165 M H z x 1 I n p u t S ig n a l S y nc 2 .5 ~ 5 . 0 V p - p s e p a r a te d s y n c I n p u t I m p e d a n c e ( A na lo g ) V id e o - 7 5 O h m S y nc - 1 k O h m C o m p o s ite S y n c C - V id e o , S - V id e o D igita l 3 c h a n n e l T M D S r e c e ive r, s in g le p ix e l 2 4 b it M S B a lign e d R G B T F T S c a n n in g F re q u e n c y H o r izo nta l 30~ 68kH z Ve r tic a l 5 6 ~ 8 5 H z ( U P to 8 5 H z a t 1 0 2 4 x 7 6 8 m o d e a n d up to 7 5 H z at 12 8 0 x 1 0 2 4) D is p la y S ize H x V 1 4 . 1 3 " x 11 . 3 " ( 3 5 9 m m x 2 8 7 m m ) B rig h t n e s s , C o n t ra s t R a d t io , G ra y S c a le s B r ig h tne s s 2 0 0 c d /m 2 , S ta n d a r d C o ntra s t R a tio 2 5 0 :1 Ty p . G r a y S c a le s U p to 2 5 6 s te p s S ig n a l I n p u t C o n n e c t o r V id e o D B 9 - 1 5 p in, D ig ita l D V I , N T S C , S - V id e o To u c h s c r e e n R S - 2 3 2 D B - 9 ( O p tio n a l) T e m p e ra t u re E n v iro n m e n t O p e r a ting Te m p e r a tu r e 4 1 ° ~ 9 5 ° F (5 ° - 3 5 °C ) S to r a ge Te m p e r a tu r e - 4 ° ~ 1 4 0 ° F (2 0 ° - 6 0 °C ) H u m id ity 1 0 ~ 9 0 % R H ( w ith o u t c o n d e n s a tio n ) P o w e r S o urc e D is p la y M o nito r DC 12V A C - A d a p te r A C 1 0 0 ~ 2 4 0 V 2 7 W ( W itho u t o p tio n , N o r m a l O p e r a tio n ) R e g u la t io n s S a fe ty a n d E M C U L /c U L , F C C , C E , T C O 9 9 , E ne r g y S ta r, C B , M P R I I , E R G /G S . V C C I , U L 2 6 0 1 - 1 , E N 6 0 6 0 1 - 1 C a b in e t D e s k to p S ta nd 1 7 . 5 inc h ( W ) x 1 7 . 8 in c h ( H ) x 9 . 5 in c h ( D ) F r e e M o u nt 1 7 . 5 inc h ( W ) x 1 4 . 2 5 in c h ( H ) x 3 in c h ( D ) W e ig h t D e s k to p S ta nd 2 2 . 8 lb . ( 1 0 . 4 K g ) F r e e M o u nt 1 8 . 1 lb . ( 8 .2 K g ) T ilt B a s e 0° Down 28° Up S te r e o s p e a k e r, U S B ( R e v 1 . 0 ) O p t io n a l M o d u le To u c h P a n e l * All contents are subject to change without notice. * Touch Screen Model doesnt include the Video-in (C-Video, S-Video) function. * Surface Wave Touchscreen model AMM17TK/18TK/19TK-TEW and Resistive Touchscreen model AMM17TK/18TK/19TK-TE AMM17TK/AMM18TK/AMM19TK SPECIFICATION 29 A M M 19TK LC D P ane l 4 8 c m /1 9 - inc h C o lo r T F T P a n e Ty p e A c tiv e M a tr ix R e s o lu tio n 1 2 8 0 d o ts x 1 0 2 4 line s ( R e c o m m e n d e d ) P ix e l P itc h 0 .2 9 4 m m D is p la y C o lo r 1 6 m illio n c o lo r s R e s p o n s e Tim e 25ms C o lo r To n e U p to 2 5 6 to n e C o lo r F ilte r R G B v e r tic a l s tr ip e typ e F a c e F in is hin g A n ti- G la r e H a r d C o a te d V ie w in g A n gle 1 7 0 ° H 1 7 0 ° V (C R > = 1 0 ) V id e o 0 .7 V p - p a n a lo g R G B & T M D S ( P a ne lL in k ) D ig ita l 165 M H z x 1 I n p u t S ig n a l S y nc 2 .5 ~ 5 . 0 V p - p s e p a r a te d s y n c I n p u t I m p e d a n c e ( A na lo g ) V id e o - 7 5 O h m S y nc - 1 k O h m C o m p o s ite S y n c C - V id e o , S - V id e o D igita l 3 c h a n n e l T M D S r e c e ive r, s in g le p ix e l 2 4 b it M S B a lign e d R G B T F T S c a n n in g F re q u e n c y H o r izo nta l 30~ 68kH z Ve r tic a l 5 6 ~ 8 5 H z ( U P to 8 5 H z a t 1 0 2 4 x 7 6 8 m o d e a n d up to 7 5 H z at 12 8 0 x 1 0 2 4) D is p la y S ize H x V 1 4 . 8 " x 11 . 9 " ( 3 7 6 m m x 3 0 1 m m ) B rig h t n e s s , C o n t ra s t R a d t io , G ra y S c a le s B r ig h tne s s 2 5 0 c d /m 2 , S ta n d a r d C o ntra s t R a tio 5 0 0 :1 Ty p . G r a y S c a le s U p to 2 5 6 s te p s S ig n a l I n p u t C o n n e c t o r V id e o D B 9 - 1 5 p in, D ig ita l D V I , N T S C , S - V id e o To u c h s c r e e n R S - 2 3 2 D B - 9 ( O p tio n a l) T e m p e ra t u re E n v iro n m e n t O p e r a ting Te m p e r a tu r e 4 1 ° ~ 9 5 ° F (5 ° - 3 5 °C ) S to r a ge Te m p e r a tu r e - 4 ° ~ 1 4 0 ° F (2 0 ° - 6 0 °C ) H u m id ity 1 0 ~ 9 0 % R H ( w ith o u t c o n d e n s a tio n ) P o w e r S o urc e D is p la y M o nito r DC 12V A C - A d a p te r A C 1 0 0 ~ 2 4 0 V 2 7 W ( W itho u t o p tio n , N o r m a l O p e r a tio n ) R e g u la t io n s S a fe ty a n d E M C U L /c U L , F C C , C E , T C O 9 9 , E ne r g y S ta r, C B , M P R I I , E R G /G S . V C C I , U L 2 6 0 1 - 1 , E N 6 0 6 0 1 - 1 C a b in e t D e s k to p S ta nd 1 7 . 5 inc h ( W ) x 1 7 . 8 in c h ( H ) x 9 . 5 in c h ( D ) F r e e M o u nt 1 7 . 5 inc h ( W ) x 1 4 . 2 5 in c h ( H ) x 3 in c h ( D ) W e ig h t D e s k to p S ta nd 2 2 . 8 lb . ( 1 0 . 4 K g ) F r e e M o u nt 1 8 . 2 lb . ( 8 .3 K g ) T ilt B a s e 0° Down 28° Up S te r e o s p e a k e r, U S B ( R e v 1 . 0 ) O p t io n a l M o d u le To u c h P a n e l * All contents are subject to change without notice. * Touch Screen Model doesnt include the Video-in (C-Video, S-Video) function. * Surface Wave Touchscreen model AMM17TK/18TK/19TK-TEW and Resistive Touchscreen model AMM17TK/18TK/19TK-TE 30 Users Guide Connectors DC Input Connector Jack Power Input The SCD-014-1-A (SHIUA CHYUAN) or equivalent. Pin Description 1 +12V DC 2 GND Video Input 15 pin D-subminiature connector. The vedor P/N is DHSB-15 FRF7(LEOCO) or equivalent. D e s c r ip t io n P in D e s c r ip t io n P in R e d V id e o N C 10 G r e e n V id e o V G A C on B lu e V id e o N C 11 N C S D A ( D D C 1 /2 ) 12 L o g ic G r o u n d H - sync 13 R e d V id e o G r o u n d V - sync 14 G r e e n V id e o G r o u n d S C L (D D C 2 B ) 15 B lu e V id e o G r o u n d 24 pin DVI-D connector. DDWG or equivalent connector. P in S ig n a l A s s ig n m e n t P in S ig n a l A s s ig nm e n t P in S ig n a l A s s ig n m e nt T.M .D .S . D a ta 2 - T.M .D .S . D a ta 1 - 17 T.M .D .S . D a ta 0 - T.M .D .S . D a ta 2 + 10 T.M .D .S . D a ta 1 + 18 T.M .D .S . D a ta 0 + T.M .D .S . D a ta 2 /4 S hie ld 11 T.M .D .S . D a ta 1 /3 S hie ld 19 T.M .D .S . D a ta 0 /5 S hie ld T.M .D .S . D a ta 4 - 12 T.M .D .S . D a ta 3 - 20 T.M .D .S . D a ta 5 - T.M .D .S . D a ta 4 + 13 T.M .D .S . D a ta 3 + 22 T.M .D .S . D a ta 5 + D D C C lo c k 14 + 5 V P ow er 22 T.M .D .S . C lo c k S hie ld D D C D a ta 15 G ro un d (fo r + 5 V ) 23 T.M .D .S . C lo c k + N o C o nn e c t 16 H o t P lug D e te c t 24 T.M .D .S . C lo c k - Touch Port 9Pin D-subminiature connector. e s c r ip t io n D C P in e s c r ip t io n P in D S R R X D R T S T X D D T R R IN L o g ic G ro u n d T S Description of Warranty AMM17TK/AMM18TK/AMM19TK 31 Advan warrants that the goods the goods sold hereunder will be free of defects in materials and workmanship, and such goods will substantially conform to the specifications furnished by Advan, and to any drawings or specifications furnished to Advan by the Buyer if approved by Advan. This warranty shall be effective only if Advan receives notice of such defect or nonconformance during the period of the warranty. Advan sole and exclusive the Advan product(s) with refurbished units provide a credit to buyer in the amount of the purchase price. Commencement and Duration of Warranty The warranty period begins on the date of shipment from Advan. The goods sold hereunder are warranted for a period of three years (36 months) from date of shipment unless otherwise agreed to by Buyer and Advan. No extension of the warranty will be given during the time the goods are in Advan possession. Place of Repair or Replacement In order to obtain service under this warranty, Buyer must notify Advan of the defect before expiration on the warranty period, and request a Return Material Authorization Number. If the configuration has been modified in any manner, the product must be returned to its original configuration before any warranty service will be perfomed by Advan. No goods are to be returned to Advan without prior authorization. Buyer will be responsible for packaging and shipping the defective goods to the Advan Service Facility with shipping charges prepaid. Limitation of Warranty Monitor: For three years (36 months) after the date of purchase, ADVAN or its Authorized Service Centers, will repair or replace if defective in material or workmanship. This Limited Warranty does not include cleaning, or damage caused by accident, neglect, misuse or improper installation or operation, any damage caused from service, maintenance, modifications or tampering by anyone other than an ADVAN Authorized Service Representative, or by the use of supplies, consumable items and conditions beyond the control of ADVAN, such as common carrier provided equipment and/or facilities, operation of ADVAN product in excess of the specifications or with the Serial Number or Rating label removed. *Touch Screen: For one year after the date of purchase, ADVAN or its Authorized Service Centers, will repair or replace if defective in material or workmanship. This Limited Warranty does not include cleaning, or damage caused by accident, neglect, misuse or improper installation or operation, any damage caused from service, maintenance, modifications or tampering by anyone other than an ADVAN Authorized Service Representative, or by the use of supplies, consumable items and conditions beyond the control of ADVAN, such as common carrier provided equipment and/or facilities, operation of ADVAN product in excess of the specifications or with the Serial Number or Rating label removed. 32 Users Guide ADVAN DISCLAIMS ALL OTHER WARRANTIES EXPRESS OR IMPLIED INCLUDING, WITHOUT LIMITATION, ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR PARTICULAR PURPOSE, EXCEPT TO THE EXTENT THAT ANY WARRANTIES IMPLIED BY LAW CANNOT BE VALIDLY WAIVED. No oral or written information or advice given by ADVAN, its authorized service center, distributors, dealers, agents or employees, shall create another warranty or modify this warranty. This warranty states ADVANs entire liability and your exclusive remedy against ADVAN for any failure of the ADVANs product to operate properly. Neither ADVAN nor anyone else involved in the development, production, or delivery of this product shall be liable for any indirect, incidental, special consequential, exemplary, or punitive damages, including lost profits, arising from the use of or inability to consequential or incidental damages, the above limitation may not apply to you. This Limited Warranty gives you special legal rights and you may also have other right, which vary from State to State. Installation Advan makes no warranty with respect to any installation of Advans product(s) by Advan, any authorized dealer, or any other person. Technical Assistance For technical assistance please call (510)490-1005 between 8:00 a.m. and 5:00 p.m. PST, Monday through Friday or email to support@mail.advancorp.com with a description of your technical issues. Service If your Medical Monitor needs service, call Advan Customer Service at (510)490-1005 between 7:00 a.m and 4:00 p.m PST, Monday through Friday or fax to (510)490-1151. You will need the units serial number and a brief description of the problem and where unit were purchased to receive a RMA number. If a service is required please return the product for service using the original shipping container with the RMA number included in package on the outside of the box. In order to protect ADVAN employees form potential health hazards, ADVAN requires that the RMA product be disinfected before returning to ADVAN for service. Any product not cleaned prior to shipment will be returned to the customer. Note: Returns will not be accepted without an assigned RMA number. In-transit damage is not covered by warranty. We suggest you always insure your shipment. Advan will only pay for the return shipment by surface transportation. It is the responsibility of the sender to prepay transportation charges. AMM17TK/AMM18TK/AMM19TK Tounchscreen User's Manual (AMM17TK-TE/AMM18TK-TE/ AMM19TE or AMM17TK-TEW/AMM18TK-TEW/AMM19TK-TEW) 33 Quick Start 1.Connect Power Code and VGA Cable of LCD Monitor. 2.Connect Touchscreen DB9 male RS-232 cable. 3.Turn the LCD display Power ON. 4.Adjust the tilt of LCD Monitor. 5.Adjust the Picture of LCD Monitor. 6.Install driver software of Touchscreen (See "Driver software" for details). 7.Adjust the calibration of Touchscreen (See "Driver software" for details). Introduction The ELO IntelliTouch Touchscreen system consists of a touchscreen and an electronic touchscreen controller. The touchscreen may be a flat, spherical, or cylindrical and is installed over the face of the LCD. The touchscreen controller installed inside of theLCD. The IntelliTouch Touchscreen The IntelliTouch surface wave touchscreen consists of a glass panel molded to the precise shape of a display's face. A scratch-resistant, hard-coated plastic cover sheet may be clear for best image clarity or have an antiglare finish. The IntelliTouch Controller The IntelliTouch controllers provide the drive signal for touchscreen, convert the received analogue signals into digital touch coordinates, and send these coordinates to the computer. 34 Users Guide Touchmonitor installation Cable Connection 1. Connect and test LCD as a video display only. 2. Plug the DB9 male into the DB9 female connector labled "TOUCHSCREEN" on the back of the LCD Monitor. Driver software ELO provide driver programs for the DOS, Windows 3.1, Windows 95/98, Windows NT, Windows 2000, Windows XP, OS/2, and Macintosh systems. Additional drivers may be available for other system. Contact ELO for details. Installing Driver software for Windows / Windows NT 1. Shutdown Windows or Windows NT and turn off your computer. 2. Install touchscreen hardware as described in the "Quick start" or "Touchmonitor installation". 3. Start your computer. 4. Insert the Windows or Windows NT driver disk into diver A or B. 5. Browse for "setup.exe" in the directory to which you extracted the driver files. 6. Type "setup.exe" in the space provided and press Enter. 7. The touchscreen setup wizard will appear. You will need to select serial port, type of touchscreen controller, and language. 8. Complete the setup program. 9. Shutdown and restart windows NT. 10. Click the start button, then click control panel. 11. Double-click touchscreen control panel. 12. Click the calibrate button and touch each of the three targets as they appear on the screen. Contacting ELO www.elotouch.com ELO Touchsystems INC. 6500 Kaiser Drive Fremont, CA 94554 USA AMM17TK/AMM18TK/AMM19TK 35
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.3 Linearized : No Create Date : 2002:09:17 17:52:51 Producer : Acrobat Distiller 3.0 for Windows Author : alanyu Creator : PageMaker 6.5 Title : 17_18_19TK(OEM,Medical)Rev1.p65 Modify Date : 2003:04:17 19:00:12+09:00 Page Count : 37 Has XFA : NoEXIF Metadata provided by EXIF.tools