User Manual
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 879176 |
| Application ID | SOlvU1dQbXAE0Om4LpZBCg== |
| Document Description | User Manual |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 89.39kB (1117422 bits) |
| Date Submitted | 2007-12-13 00:00:00 |
| Date Available | 2007-12-13 00:00:00 |
| Creation Date | 2007-10-19 10:41:13 |
| Producing Software | Acrobat Distiller 7.0 (Windows) |
| Document Lastmod | 2007-11-30 10:47:47 |
| Document Title | Untitled-1 |
| Document Creator | Adobe PageMaker 7.0 |
| Document Author: | alanyu |
AUTO - SCANNING WITH DIGITAL CONTROL LCD COLOR MEDICAL MONITOR AMM240WTD Operation Manual For future reference, record the serial number of your display monitor in the space below : Serial Number The serial number is located on the back of the monitor AMM240WTD 1 back of the monitor WARNING The title "WARNING" is used to inform the users of possible causes that could inflict the injury, death, or property damage to the patients. CAUTION The title "CAUTION" is used to inform the users of possible causes that could i nfli ct the pati ents although i t mi ght not severe enough to cause deaths. NOTE The title "NOTE" is used to inform the users of items that are o f i m p o r t a nc e i n t e r m s o f i ns t a l l a t i o n, o p e r a t i o n, o r maintenance of the Equipment although the failure does not inflict the bodily harm to the patients. ADAVN INT’L CORP.2007 All other trademarks are the property of their reference owners. This document is subject to change without notice. Advan provides this information as reference only. Reference to other vendor’s products does not imply any recommendation or endorsement. Revision Control Date Description REV.02 091107 Document number 2 User’s Guide TABLE OF CONTENTS Product Description and Intended Use...................................................... 3 Warnings and Cautions................................................................................4 Symbol Explanations....................................................................................7 EU Declaration of Conformity for Medical Applications...........................8 Safety Precaution......................................................................................... 9 Cleaning Your Monitor.................................................................................. 9 Power Management Function....................................................................10 Preset Modes..............................................................................................11 Video Signals..............................................................................................12 PIP / POP / PBP function...........................................................................13 DDC.............................................................................................................14 Installation....................................................................................................14 Connecting the Power Cord......................................................................15 User Function / Messages.........................................................................16 OSD Section...............................................................................................17 Troubleshooting.......................................................................................... 24 25 Specification of (AMM240WTD).................................................................. Classification.............................................................................................. 26 Electromagnetic Compatibility.................................................................. 27 Dimension Drawing (mm)..........................................................................30 Connectors..................................................................................................31 Description of Warranty..............................................................................32 AMM240WTD 3 Product Description and Intended Use Please check the following items are present when you unpack the box, and save the packing materials in case you will need to ship or transport the monitor in future. • AMM240WTD LCD Monitor and two video cables (1) HD15 VGA cable* (1) DVI-D cable* • AC Power cord** • AC-Adapter • Composite Video BNC Jack Cable and Super Video Cable • User Manual and 4pcs VESA screws *Might be optional item, check with local representative **Might vary pending on region stardard CAUTION Manufacturer : JEC Korea Model No : JMW1150KA2400F04 4 User’s Guide Warnings and Cautions Please read this manual and follow its instructions carefully. The words warning, caution, and note carry special meanings and should be carefully reviewed: Warning The personal safety of the patient or physician may be involved. D isregarding this information could result in injury to the patient or physician. C aution Special service procedures or precautions must be follow ed to avoid damaging the instrument. N ote Speci al i nformati on to make mai ntenance easi er or i mportant i nformati on more clear. An exclamati on mark wi thi n a tri angle i s i ntended to alert the user to the presence of i mportant operati ng and mai ntenance i nstructi ons i n the li terature accompanyi ng the product. A li ghtni ng bolt wi thi n a tri angle i s i ntended to warn of the presence of hazardous voltage. Refer all servi ce to authori zed personnel. Warning TO AVOID POTEN TIAL SER IOU S IN JU RY TO TH E U SER AN D TH E PATIEN T AN D /OR D AMAGE TO TH IS D EVIC E, TH E U SER MU ST : Warranty is void if any of these warnings are disregarded. ADVAN Int’l Corp accepts full responsibility for the effects on safety, reliability, and performance of the equipment only if: • Re-adjustments, modifications, and/or repairs are carried out exclusively by ADVAN Int’l Corp. • The electrical installation of the relevant operating room complies with the applicable IEC and CE requirements. Warning Federal law (United States of America) restricts this device to use by, or on order of a physician. The ADVAN Int’l Corp AMM240WTD monitor has been tested under UL 60601-1 standard and UL listed for Medical application. ADVAN Int’l Corp reserves the right to make improvements in the product(s) described herein. Product(s), therefore, may not agree in detail to the published design or specifications. All specifications are subject to change without notice. Please contact ADVAN Int’l Corp directly or phone your local ADVAN Int’l Corp sales representative or agent for information on changes and new products. Warnings AMM240WTD 5 1. Read the operating manual thoroughly and be familiar with its contents prior to using this equipment. 2. Carefully unpack the unit and check if any damage occurred during shipment. 3. Should any solid object or liquid fall into the panel, unplug the unit and have it checked by qualified personnel before operating it any further. 4. Uplug the unit if it is not to be used for an extended period of time. To disconnect the cord, pull it out by the plug. Never pull the cord itself. 5. Be a qualified physician, having complete knowledge of the use of this equipment. 6. Test this equipment prior to a medical procedure. This monitor was fully tested at the factory before shipment. 7. Avoid removing covers on control unit to avoid electric shock. 8. Attempt no internal repairs or adjustments not specifically detailed in this operating manual. 9. Pay close attention to the care, cleaning instructions in this manual. A deviation may cause damage (refer to the Cleaning section). 10. DO NOT STERILIZE MONITOR. 11. Read the entire instruction manual before assembling or connecting the camera. 12. Do not place the monitor or any other heavy object on the power cord. Damage to the cable can cause fire or electirc shock. 13. Monitor with power supply is suitable for use in patient environment. 14. DO NOT stack more than 8 boxes high. 15. When the monitor is equipped with the base stand, please install the base stand at horizontally flat place for normal use. This equipment has been tested and found to comply with the limits for medical devices in IEC 601-1-2:2003. These limits are designed to provide reasonable protection against harmful interference in a typical medical installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to other devices in the vicinity. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to other devices, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving device. - Increase the separation between the equipment. - Connect the equipment into an outlet on a circuit different from that to which the other device(s) are connected. - Consult the manufacturer or field service technician for help. NOTICES TO USER This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC WARNING This equipement generates or uses radio frequency energy. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. The user could lose the authority to operate this equipment if an unauthorized change or modification is made. 6 User’s Guide Cautions 1. The AC Adapter must be plugged into a Grounded power outlet. 2. Use only the proprietary AMM240WTD power supply for the AMM240WTD monitor. Make a proper connection by ensuring that the shrink tubing completely secures the connection between the DC power cord and the extension cord. 3. Turn power off when unit is not in use. 4. Never operate the unit right after having transported from a cold location directly to a warm location. 5. Do not expose the monitor to moisture or directly apply liquid cleaners directly to the screen. Spray the cleaning solution into a soft cloth and clean gently. 6. Handle the monitor with care. Do not strike or scratch the screen. 7. Do not block the monitor cooling vents. The monitor is cooled by natural convection and has no fan. 8. Do not force the monitor past 28 degrees of vertical when adjusting the screen position. (For monitors equipped with stands only.) 9. Remove the power module and connection when transporting the unit. 10. Save the original carton and associated packing material. They will be useful should you have to transport or ship the unit. 11. Allow adequate air circulation to prevent internal heat buildup. 12. Do not place the unit on surfaces (rugs, blankets, etc.) or near materials (curtains, draperies) that may block the ventilation slots. 13. Do not install the unit near sunlight, excessive dust, mechanical vibration or shock. 14. The unit is designed for operation in a horizontal position. Never operate the unit in a vertical position. 15. Keep the unit away from equipment with strong magnets (i.e. a large loudspeaker.) 16. Do not expose the monitor to moisture or excessive dust. 17. Equipment with SIP/SOP connectors should either comply with IEC 60601-1 and/or IEC 60601-1-1 harmonized national standard or the combination should be evaluated. Do not touch the patient with signal input or output connectors. 18. Use only a hospital grade power supply cord. 19. This equipment has been tested and found to comply with the limit for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide resonable generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation, which can be detemined by turing the equipment off and on, the user is encourage to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving device. • Increase the separation distance between the equipment. • Connect the equipment to an outlet on a circuit different from that to which the other device(s) are connected. • Consult the manufacturer or field service technican for help. 20. Grounding reliability can only be achieved when the equipment is connected to an equipment receptacle labeled “Hospital Only” or “Hospital Grade.” Note To connect to an international power supply, use a an attachment plug appropriate for the power outlet. Note Refer to the “Electromagnetic Compatibility” (EMC) section of this manual to ensure EMC. The AMM240WTD must be installed and operated according to the EMC information provided in this manual. AMM240WTD 7 Symbol Definitions 8 User’s Guide EU Declaration of Conformity for Medical Applications A Declaration of Conformity has been filed for this product. A sample of this document may be found in the addendum which accompanied this manual. For a copy of the Declaration of Conformity document, please contact ADVAN Int’l Corp. and request for AMM240WTD DOC. Prepare for Unpack Before you unpack your monitor, prepare a suitable workspace. You need a stable and level surface near a grounded wall outlet in an area which is relatively free of glare from sunlight or other sources of bright light. The monitor is cooled by natural convection (it has no fan). For optimum performance, do not block the cooling vents. While unpacking the monitor, inspect it and other package contents for shipping damage that could cause a fire or shock hazard. Immediately report any shipping damage to the carrier or transportation company and contact customer service for monitor in the future or in case of return. After you unpack the monitor, make sure the following items are included • Monitor with video cable • AC adapter with cable CAUTION: AC Adapter must be plugged into Grounded a power outlet CAUTION : AC adapter Manufacturer: JEC Korea Model No: JMW1150KA2400F04 • This operations manual Note: Your system provider may offer alternative cords or cables depending on the installation requirement and local geography issues. AMM240WTD 9 SAFETY PRECAUTION · · · · · · Avoid placing the monitor, or any other heavy object, on the power cord to prevent fire or electrical shock from damage to the power cord. Do not expose the monitor to rain, excessive moisture, or dust to avoid fire or shock hazard. Do not cover the slots or openings of the monitor for proper heat dissipation. Always put the monitor in a place where there is adequate ventilation. Avoid placing the monitor against a bright background or where sunlight or other light sources may reflect on the area of the monitor. Place the monitor just below eye level. Handle with care when transporting the monitor. Refrain from giving the shock or scratch to the screen, as screen is fragile. CLEANING YOUR MONITOR No specific liquid or chemical necessary when cleaning this LCD monitor However, we suggest to clean the monitor with non-abrasive cloths and cleaning solutions used in hospitals to clean similar equipment. We recommend using 70% Isopropyl alcohol for the screen surface and warm water and a mild detergent for all other surfaces. Other acceptable cleaning agents are listed below: • 70% isopropyl alcohol • Cidex (2.4% glutaraldehyde solution) • 0.5% Chlorhexidine in 70% isopropyl alcohol To clean the screen, do not spray liquid cleaners directly on to the unit. Stand away Form the monitor and spray cleaning solution onto a cloth. Without applying excessive pressure, clean the screen with the slightly dampened rag. 10 User’s Guide POWER MANAGEMENT FUNCTION The monitor is equipped with the power management function which automatically reduce the power consumption when not in use in three power level modes. • Stand-by Mode The monitor goes into stand-by mode when the horizontal sync signal is off for about 10 seconds. In this mode, the screen goes off and the power LED blinks for 1 seconds On and 1 second Off. The screen is displayed after the horizontal sync signal is restored. • Suspend Mode The monitor goes into suspend mode when the vertical sync signal is off for about 10 seconds. The power consumption during this is less than 8 W. In this mode, the screen goes off and the power LED blinks for 1 seconds On and 1 second Off. The screen is displayed after the vertical sync signal is restored. • Off Mode The monitor goes into power-off mode when the vertical and horizontal sync signals are off for about 10 seconds. In this mode, the screen goes off and the power LED blinks for 1 seconds On and 1 second Off. The screen is displayed after the vertical and horizontal sync signals are restored. Power Management System The AMM240WTD Medical Monitor power management proposal. Provides four phases of power-saving modes by detecting the horizontal sync signal as shown in the table below. State Normal Operation DPMS Standby DPMS suspend DPMS Off Horizontal Sync Active Inactive Active Inactive Vertical Sync Active Active Inactive Inactive Video Active Blanked Blanked Blanked Power Indicator Green Red Flashing (1 sec. Interval) Red Flashing (1 sec. Interval) Red Flashing (1 sec. Interval) Power Consumption 97W 27W 27W 27W When the monitor is power saving mode or detects an incorrect timing, the screen will be blank and power LED indicator will blink. AMM240WTD 11 PRESET MODES R esolution H oriz ontal frequency ( KHz ) Vertical frequency ( Hz ) P ixel clock ( MH z ) 640 x 350 @60Hz 31.469 59.941 25.175 640 x 350 @70Hz 31.469 70.087 25.175 640 x 350 @85Hz 37.86 85.080 31.500 640 x 400 @60Hz 31.469 59.941 25.175 640 x 400 @70Hz 31.469 70.087 25.175 640 x 400 @85Hz 37.86 85.080 31.500 640 x 480 @60Hz 31.469 59.940 25.175 640 x 480 @72Hz 37.861 72.809 31.500 640 x 480 @75Hz 37.500 75.000 31.500 640 x 480 @85Hz 43.269 85.008 36.000 720 x 400 @85Hz 37.927 85.038 35.500 800 x 600 @56Hz 35.156 56.250 36.000 800 x 600 @60Hz 37.879 60.317 40.000 800 x 600 @72Hz 48.077 72.188 50.000 800 x 600 @75Hz 46.875 75.000 49.500 800 x 600 @85Hz 53.674 85.061 56.250 1024 x 768 @43Hz 35.522 86.958 44.900 1024 x 768 @60Hz 48.363 60.004 65.000 1024 x 768 @70Hz 56.476 70.069 75.000 1024 x 768 @75Hz 60.023 75.029 78.750 1024 x 768 @85Hz 68.677 84.997 94.500 1152 x 864 @60Hz 54.348 60.053 80.000 1152 x 864 @70Hz 63.955 70.016 94.200 1152 x 864 @75Hz 67.500 75.000 108.000 1280 x 960 @60Hz 60.000 60.000 108.000 1280 x 960 @85Hz 85.938 85.002 148.500 1280 x 1024 @60Hz 63.974 60.013 108.500 1280 x 1024 @75Hz 79.976 75.025 135.000 1280 x 1024 @85Hz 91.146 85.024 157.500 1600 x 1200 @60Hz 75.000 60.000 162.000 1920 x 1200 @60Hz 74.099 59.999 154.125 12 User’s Guide Video Signals C omponent / RGB Format C -Vi deo S-Vi deo NTSC PAL 480/59.94i SD I1 SD I2 480/59.94p 576/50i 576/50p Y/Pb/Pr RGB 720/50p 720/59.94p 720/60p 1035/59.94i 1035/60i 1080/23.98psf 1080/24psf 1080/23.98p 1080/24p 1080/25p 1080/29.97p 1080/30p 1080/50i 1080/50p 1080/59.94i 1080/59.94p 1080/60i 1080/60p AMM240WTD 13 PIP / POP / PBP function The following combination options are available to you: Main PIP VGA D VI SDI1 SDI2 C-Video S-Video Component VGA D VI SDI1 SDI2 C-Video S-Video Component 14 User’s Guide DDC To make your installation easier, the monitor is able to Plug and Play with your system if your system also supports DDC protocol. The DDC (Display Data Channel) is a communication protocol through which the monitor automatically informs the host system about its capabilities, for example, supported resolutions and corresponding timing. The monitor supports DDC1 and DDC2B standard. INSTALLATION To install the monitor to your host system, please follow the steps as given below: Steps 1. Use the supplied video cable (DVI, VGA, S-Video, C-Video) then connect to the host system accordingly. 2. Connect the DC power to the DC power connector on the monitor. 3. Connect one end of AC power cord into the AC Adapter and the other end to AC power outlet. 4. Then turn the host system on and then the monitor. 5. If the monitor still does not function properly, please refer to the troubleshooting section to diagnose the problem. S - Video DVI VGA SDI IN IN OUT DC Power C - Video RGB / Component SDI OUT AMM240WTD 15 CONNECTING the POWER CORD * Check first to make sure that the power cord you use is the correct type required for your area. * This monitor has an universal AC adapter that allows operation in either AC 100 - 240 V ac voltage area. No user-adjustment is required. * Plug one end of the power cord to the AC adapter, plug another end to a proper AC outlet. The cord set should have the appropriate safety approvals for the country in which the equipment will be installed and marked HAR. For 120 volt Applications, use only UL Listed deachable power cord with NEMA configuration 5-15P type (parallel blades) plug cap. For 240 volt applications use only UL Listed Detachable power supply cord with NEMA configuration 6-15P type (tandem blades) plug cap. Hospital-grade power cord Extension power cord (optional) Manfacturer: JEC Korea Model No: 1501047 (15ft) or 1501047001 (75ft) Power Supply Manufacturer: JEC Korea Model No: JMW1150KA2400F04 AMM240WTD 16 User’s Guide User Functions / Messages Key Name and Function Power LED : Lights up to indicate the power is turned ON. Power Switch : To power ON or OFF the monitor. Rotary switch : With the OSD menu activated, increases the value of the selected (Ture Right) parameter or moves rightward in OSD menu. Rotary switch : With the OSD menu activated, increases the value of the selected (Ture Left) parameter or moves leftward in OSD menu. PIP Switch : To enable or disable Picture In Picture function. PBP Switch : To enable or disable Picture By Picture function. POP Switch : To enable or disable Picture On Picture function. Adjust Switch : To activate or deactivate image adjustment in sub screen of PIP, PBP, POP mode. Locker Switch : To turn ON or OFF the system. How to access the menu 1. Push the “Knob” button to activate the OSD menu. 2. Able to turn left or right the button to select those icons. The icon will be highlighted when is selected. 3. Push the “knob” button to go into the another OSD menu. 4. Turn left or right “Knob” button to increase or decrease the number of selected function. 5. In order to exit from the OSD menu in a different layer, then choose the “Exit option”. In case of long pushing and holding the button around two or three seconds, then it will completely out from the menu regardless wherever you are. 6. Turn the “Knob” button in a fast way to the left or right, while the menu is not activated, then input signal menu will turns up with “V” mark which is chosen current available input signal. You can switch to another input signal source by turning the knob slowly then select the target source by pushing the knob. AMM240WTD 17 OSD Section Main Menu Chromatic Adjust Color Temp, Gamma Visual Adjust Brightness, Contrast, Phase, Chroma, Sharpness-H, Sharpness-V Setting Adjust Scale Mode, Mirror, Freeze Frame, Zoom / Pan, PIP / POP, PBP Advanced Adjust OSD Position Control, Screen Control, DPMS, Auto Source Select, Smart Select, Restore Factory, Key Lock Information Adjust Custom Entry, SN, Run Time, Input Format 18 User’s Guide OSD Section Chromatic Color Temp Change the color temperature - D65, D93, S1, S2, S3, S4 Gamma Change the gamma value - 1.8, 1.9, 2.0, 2.1, 2.1S, 2.2, 2.3, 2.4, 2.4S, S0, Radio graph Exit Exit the menu Visual Brightness Adjust the brightness of panel (Range 0 - 100) Contrast Adjust the contrast of video (Range 0 - 100) Phase Adjust the phase of video (Range 0 - 100) *available for C and S - video Chroma Adjust the chroma of video (Range 0 - 100) *available for C and S - video Sharpness-H Set the sharpness of horizontal image (Range 0 - 100) Sharpness-V Set the sharpness of vertical image (Range 0 - 100) Exit Exit the menu AMM240WTD 19 OSD Section Setting Scale Mode Change the scale mode - Fill all, Vertical - fill, Horizontal - fill, One to One, Center - fill, Fill aspect ratio Mirror Off / On mirror image Freeze Frame Off / On freeze frame Zoom / Pan Enable zoom - in and pan function PIP Enable PIP (Picture In Picture) function PBP Enable PBP (Picture By Picture) function Exit Exit the menu 20 User’s Guide OSD Section Sub menu of PIP Mode PIP Mode ON / Off Source PIP sub screen source - SDI1,2, C-Video, S-Video, Component, VGA, DVI Position PIP sub screen position - Top L, Top R, Bottom L, Bottom R Size PIP sub screen size - Small, Medium, Large Blending PIP sub screen blending (Range 0 - 100) Swap PIP sub screen swap Exit Exit the menu Sub menu of PBP Mode PBP Mode ON / Off Source PBP sub screen source - SDI1,2, C-Video, S-Video, Component, VGA, DVI Swap PBP sub screen swap Exit Exit the menu AMM240WTD 21 OSD Section Advanced OSD Position Change the OSD menu - Position, Background, Control OSD time out, Language Screen Control Control and adjust H and V position, Freqency, Phase Noise Reduction, Motion Offset DPMS Change the DPMS Auto Source Adjust Auto Source Select between on and off Select Smart Select Enable / Disable smart select sub menu Restore Factory Changes the all OSD value to factory outgoing status Key Lock Set to key lock mode Exit Exit the menu 22 User’s Guide OSD Section Sub menu of OSD Control H-position Adjust OSD H - position (Range 0 - 100) V-position Adjust OSD V - position (Range 0 - 100) Back ground Adjust transparency of OSD back ground (Range 0 - 100) OSD Time out Adjust OSD time out - 5s, 10s, 15s, 20s, 1m, 2m Language OSD language - English, Japanese, Chinese, Korean, French, German Exit Exit the menu Sub menu of Screen Control H-position Adjust screen H - position (Range 0 - 100) V-position Adjust Screen V - position (Range 0 - 100) Frequency Adjust frequency (Range 0 - 100) *available for VGA Phase Adjust phase (Range 0 - 100) *available for VGA Noise Noise Reduction (Range 0 - 100) Reduction *available for Component, C-Video and S-Video Motion Offset Motion Offset (Range 0 - 15) *available for Component, C-Video and S-Video Exit Exit the menu AMM240WTD 23 OSD Section Information Custom Entry Change the user or monitor’s name SN Display the serial number Run Time Display the total run time Input Format Display the current input resolution and vertical frequency Exit Exit the menu 24 User’s Guide TROUBLESHOOTING Before sending your LCD monitor for servicing, please check the troubleshooting list below to see if you can self-diagnose the problem. Problems C urrent Status R emedy LED ON · Usi ng OSD , adjust bri ghtness and contrast to maxi mum or reset to thei r default setti ngs. LED OFF · C heck the Locker swi tch and Power swi tch. · C heck i f AC power cord i s properly connected to the AC adapter. · C heck i f vi deo si gnal cable i s properly connected at the back of moni tor. · C heck i f the power to computer system i s ON. Unstable Pi cture · C heck i f the speci fi cati on of graphi cs adapter and moni tor i s i n compli ance whi ch may be causi ng the i nput si gnal frequency mi smatch. D i splay i s mi ssi ng, center shi ft, or too small or too large i n di splay si ze · Usi ng Auto Setup button, i f sti ll di splay abnormal pi cture then adjust C LOC K, C LOC KPHASE, H-POSITION and V-POSITION wi th non-standard si gnals. · Usi ng OSD , i n case of mi ssi ng full-screen i mage, please select other resoluti on i n your Operati ng System (Wi ndows 95/98, NT) or other verti cal refresh ti mi ng. · Must wai t for a few seconds after adjusti ng the si ze of the i mage before changi ng or di sconnecti ng the si gnal or poweri ng OFF the moni tor. No Pi cture LED Bli nki ng Abnormal Pi cture AMM240WTD 25 SPECIFICATION AMM2 1 3 T D L C D P a ne l 2 4 .0 " TF T L C D P a ne l Typ e A cti ve Ma tri x Re so luti o n 1 9 2 0 x 1 2 0 0 @ 7 5 Hz P i xe l P i tch 0 .2 7 mm D i sp la y C o lo r 1 6 .7 M co lo rs C o lo r To ne Up to 2 5 6 co lo r to ne Re sp o nse Ti me <2 5 ms Typ . F a ce F i ni shi ng P ro te cti ve F i lte r wi th A nti -Re fle cte d Ha rd C o a te d V i e wi ng A ng le +/- 8 5 °(Ho ri zo nta l), +/- 8 5 ° (ve rti ca l) In p u t S ig n a l (An a lo g & D ig ita l) S ync (A na lo g ) 2 .5 ~5 .0 V p -p se p a ra te d sync C o mp o si te S ync (A na lo g ) C o mp o si te V i d e o (NTS C /PA L ) Y/C S ync (A na lo g ) S -V i d e o (NTS C /PA L ) Inp ut Imp e d a nce (A na lo g ) V i d e o - 7 5 Ohm S ync - 1 k Ohm D i g i ta l 3 cha nne l TMD S re ce i ve r, si ng le p i xe l 2 4 -b i t MS B a li g ne d RGB TF T S c a n n in g F re q u e n c y Ho ri zo nta l 3 1 .4 7 ~7 9 .9 8 kHz Ve rti ca l 5 0 ~7 5 .3 Hz D is p la y S iz e HxV 2 0 .4 " x 1 2 .8 " (5 1 8 .4 mm x 3 2 4 mm) B rig h tn e s s , C o n tra s t R a d tio , Gra y S c a le s B ri g htne ss 7 0 0 cd /m2 (Typ .) C ontrast Rati o 9 0 0 :1 (Typ .) S ig n a l In p u t C o n n e c to r V i deo D V I, HD 1 5 , S D /HD -S D I 1 a nd 2 , C o mp o ne nt Y/G, P b /B , P r/R, H/C S , V S , C -V i d e o a nd S -V i d e o C o mmuni ca ti o n D B 9 (RS 2 3 2 ) S ig n a l Ou tp u t C o n n e c to r (L o o p T h ro u g h ) V i deo S D /HD -S D I, C o mp o ne nt Y/G, P b /B , P r/R, H/C S , V S , C -V i d e o a nd S -V i d e o Op e ra tin g /S to ra g e E n v iro n me n t Op e ra ti ng Te mp e ra ture 3 2 ° ~ 9 0 °F (0 ° - 3 2 °C ) Sto ra g e Te mp e ra ture -4 ° ~ 1 4 0 °F (-2 0 ° - 6 0 °C ) Humi d i ty 1 0 ~ 9 0 %RH (wi tho ut co nd e nsa ti o n) V E S A Mo u n tin g 1 0 0 mm x 1 0 0 mm P o w e r S o u rc e D i sp la y Mo ni to r D C 24V A C -A d a p te r A C 1 0 0 ~2 4 0 V 1 2 0 W Ma x +/-1 0 % R e g u la tio n s S a fe ty, E MI & E nvi ro nme nta l UL 6 0 6 0 1 -1 , E N6 0 6 0 1 -1 , E N6 0 6 0 1 -1 -2 , F C C , C E , C C C , V C C I, ROHS , IP :X 1 C o mp li a nce D ime n s io n F re e Mo unt 2 3 .5 4 " (W) x 1 5 .0 7 " (H) x 4 .3 9 " (D ) 5 9 8 mm (W) x 3 8 2 .9 mm (H) x 111 .5 mm (D ) We ig h t F re e Mo unt 1 6 .9 lb s (7 .6 6 K g ) Op tio n a l Mo d u le B a se Sta nd A d justa b le hi g h, swi ve l a nd ti lt b a se sta nd ** All contents are subject to change without notice. 26 User’s Guide 51LJ Medical Equipment E215822 This monitor is intended for use in Health Care Facilities model AMM240WTD Equipment is not suitable for use in the presence of flammable anesthetic mixture with air or with oxygen or nitrous oxide. No user serviceable parts inside, ask qualified personnel when accessing inside. For disposal of waste product, follow the requirement of local code. Electrical input rating: 24V DC 6.25A Classification Type of protection against electric shock: Class I Equipment. Degree of protection against the ingress of water: IPX1 compliance. Mode of operation: Continuous This monitor has been tested to comply with IEC/EN 60601-1, IEC/EN60601-1-2 and is certified by UL to medical standard UL60601-1(UL/cUL Mark). Because many medical offices are located in residential areas, this monitor, in addition to the medical requirements, has also been tested and found to comply with the limits for FCC Class B computing devices in a typically configured system. It is the system integrator or configurer’s responsibility to test and ensure that the entire system complies with applicable EMC laws. Environmental conditions for transport and storage: - Temperature range within -4° to 140° F (-20° to 60° C) - Relative humidity range within 10% to 90% - Atmospheric pressure range within 500 to 1060 hPa. AMM240WTD 27 Electromagnetic Compatibility Like other electrical medical equipment, the AMM240WTD requires special precautions to ensure electromagnetic compatibility with other electrical medical devices. To ensure electromagnetic compatibility (EMC), the AMM240WTD must be installed and operated according to the EMC information provided in this manual. Note The AMM240WTD has been designed and tested to comply with IEC 60601-1-2:2001 requirements for EMC with other devices. Caution Portable and mobile RF communications equipment may affect the normal function of the AMM240WTD. Warning Do not use cables or accessories other than those provided with the AMM240WTD, as this may result in increased electromagnetic emissions or decreased immunity to such emissions. Warning If the AMM240WTD is used adjacent to or stacked with other equipment, observe and verify normal operation of the AMM240WTD in the configuration in which it will be used prior to using it in a surgical procedure. Consult the tables below for guidance in placing the AMM240WTD. Manufacturer’s declaration - electromagnetic emission The Model AMM240WTD is intended for use in the electromagnetic environment specified below. The customer or the user of AMM240WTD should assure that it is used in such an environment. Emission test C ompliance RF emi ssi ons C ISPR 11 Group 1 RF emi ssi ons C ISPR 11 C lass B Harmoni c emi ssi ons IEC 61000-3-2 C lass D Voltage Fluctuati ons IEC 61000-3-3 C ompli es Electromagnetic environment - guidance The Model AMM2140WD uses RF energy only for i ts i nternal functi on. Therefore, i ts RF emi ssi ons are very low and are not li kely to cause any i nterference i n nearby electroni c equi pment AMM240WTD i s sui table for use i n all establi shments, i ncludi ng domesti c establi shments and those di rectly connected to the publi c low-voltage power supply network that suppli es bui ldi ngs used for domesti c purposes Manufacturer’s declaration - electromagnetic immunity The Model AMM240WTD is intended for use in the electromagnetic environment specified below. The customer or the user of AMM240WTD should assure that it is used in such an environment. Immunity Test IE C 60601 Test Level C ompliance Level E lectromagnetic environment - guidance Floors should be wood, concrete or cerami c ti le. If floors are covered wi th syntheti c materi al, the relati ve humi di ty should be at least 30%. E lectrostati c di scharge (E S D ) IE C 61000-4-2 6 kV contact 8 kV a i r 6 kV contact 8 kV a i r E lectri cal fast transi ent /burst IE C 61000-4-4 2 kV for power supply li nes 1 kV for i nput / output li nes 2 kV for power supply li nes 1 kV for i nput / output li nes Mai ns power quali ty should be that of a typi cal commerci al or hospi tal envi ronment. 1 kV di fferenti al mode 2 kV common mode 1 kV di fferenti al mode 2 kV common mode Mai ns power quali ty should be that of a typi cal commerci al or hospi tal envi ronment. S urge IE C 61000-4-5 28 User’s Guide P ower frequency (50/60Hz) magneti c fi eld IE C 61000-4-8 Voltage di ps, short i nterrupti ons and voltage vari ati ons on power supply i nput li nes IE C 61000-4-11 3.0 A /m 3.0 A /m <5% Ut (>95% di p i n Ut) for 0.5 cycle <5% Ut (>95% di p i n Ut) for 0.5 cycle 40% Ut (60% di p i n Ut) for 5 cycles 40% Ut (60% di p i n Ut) for 5 cycles 70% Ut (30% di p i n Ut) for 25 cycles 70% Ut (30% di p i n Ut) for 25 cycles <5% Ut (>95% di p i n Ut) for 5 sec. <5% Ut (>95% di p i n Ut) for 5 sec. P ower frequency magneti c fi elds should be at levels characteri sti c of a typi cal locati on i n a typi cal commerci al or hospi tal envi ronment. Mai ns power quai li ty should be that of a typi cal commerci al or hospi tal envi ronment. If the user of the A MM240WTD i mage i ntensi fi er requi res conti nued operati on duri ng power mai ns i nterrupti ons, i t i s recommended that the A MM240WTD i mage i ntensi fi er be powered from an uni nterrupti ble power supply or a battery. N ote: U t i s the A .C . mai ns voltage pri or to appli cati on of the test level. Manufacturer’s declaration - electromagnetic immunity The Model AMM240WTD is intended for use in the electromagnetic environment specified below. The customer or the user of AMM240WTD should ensure that it is used in such an environment. Immunity Test IEC 60601 Test Level C ompliance Level Electromagnetic environment - guidance Portable and mobi le RF communi cati ons equi pment should be used no closer to any part of the AMM240WTD , i ncludi ng cables, than the recommended separati on di stance calculated from the equati on appli cable to the frequency of the transmi tter. C onducted RF IEC 61000-4-6 3 Vrms 150 KHz to 80 MHz 3 Vrms 150 KHz to 80 MHz Radi ated RF IEC 61000-4-3 3 V/m 80MHz to 2.5 GHz 3 V/m 80MHz to 2.5 GHz R ecommended Separation D istance 0.15 MHz to 80 MHz 80 MHz to 800 MHz 800 MHz to 2.5 GHz where P i s the maxi mum oputput power rati ng of the transmi tter i n watts (W) accordi ng to the transmi tter manufacturer and d i s the recommended separati on di stance i n meters (m). Fi eld strengths from fi xed RF transmi tters, as deter-mi ned by an electromagneti c si te survey (a), should be less than the compli ance level i n each frequency range (b). Interferency may occur i n the vi ci ni ty of equi pment marked wi th the follwi ng symbol: NOTE 1: At 80MHz and 800MHz, the hi gher frequency range appli es. NOTE 2: These gui deli nes may not apply i n all si tuati ons. Electromagneti c propagati on i s affected by absorpti on and reflecti on from structures, objects, and people. (a) Fi eld strengths from fi xed transmi tters, such as base stati ons for radi o (cellular/cordless) telephones and land mobi le radi os, amateur radi o, AM and FM radi o broadcast and TV broadcast, connot be predi cted theoreti cally wi th accuracy. To assess the electromagneti c envi ronment due to fi xed RF transmi tters, an electromagneti c si te survey should be consi dered. If the measured fi eld strength i n the locati on i n whi ch the AMM240WTD i s used exceeds the appli cable RF compli ance level above, the AMM240WTD should be observed to veri fy normal operati on. If abnormal performance i s observed, addi ti onal measures may be necessary, such as reori enti ng or relocati ng the AMM240WTD . (b) Over the frequency range 150kHz to 80MHz, fi eld strengths should be less than [V1] V/m. AMM240WTD 29 R ecommended Separation D istances B etw een Portable and Mobile R F C ommunications Equipement and the AMM240WTD System The AMM240WTD system is intended for use in an electromagnetic environment in w hich radiated R F disturbances are controlled. The user of the AMM240WTD system can help prevent electromagnetic interference by maintaining a minimum distance betw een portable and mobile R F communications equipment (transmitters) and the AMM240WTD system as recommended below, according to the maximum output pow er of the communications equipment. R ated maximum output pow er (W) of transmitter Separation distance (m) according to frequency of transmitter 150kHz to 80MHz d=1.17, p 80MHz to 800MHz d=1.17, p 800MHz to 2.5GHz d=2.33, p 0.01 0.12 0.12 0.23 0.1 0.37 0.37 0.74 1.17 1.17 2.33 10 3.70 3.70 7.37 100 11.70 11.70 23.30 For transmi tters rated at a maxi mum output power not li sted above, the recommended separati on di stance (d) i n meters (m) can be esti mated usi ng the equati on appli cable to the frequency of the transmi tter, where P i s the maxi mum output power rati ng of the transmi tter i n watts (W) accordi ng to the transmi tter manufacturer. NOTE 1: At 80 MHz and 800 MHz, the separati on di stance for the hi gher frequency range appli es. NOTE 2: These gui deli nes may not apply i n all si tuati ons. Electromagneti c propagati on i s affected by absorpti on and reflecti on from structures, objects, and people. 30 User’s Guide Dimension Drawing (mm) AMM240WTD 31 Connectors DC Input Connector Jack Power Input P in D escription P in GND D escription NC GND V C C _24V V C C _24V Video Input 24 pin DVI-I connector. DDWG or equivalent connector. P in D escription P in D escription P in T.M.D .S . D ata2- 11 T.M.D .S . D ata1 S hi eld 21 D escription NC T.M.D .S . D ata2+ 12 NC 22 T.M.D .S . C lock S hi eld T.M.D .S . D ata2 S hi eld 13 NC 23 T.M.D .S . C lock+ NC 14 +5V P ower 24 T.M.D .S . C lock- NC 15 Ground (for +5V ) 25 A nalog Red D D C C lock 16 Hot P lug D etect 26 A nalog Green D D C D ata 17 T.M.D .S . D ata0- 27 A nalog B lue A nalog V - S ync 18 T.M.D .S . D ata0+ 28 A nalog H - S ync 29 GND (for analog si gnal) D escription T.M.D .S . D ata1- 19 T.M.D .S . D ata0 S hi eld 10 T.M.D .S . D ata1+ 20 NC 15 pin VGA connector. P in D escription P in D escription P in GRE D GND 11 NC GGRE E N GND 12 GS D A IHS GB LUE GND 13 GND G5V 14 IV S GND 10 GND 15 GS C L P in D escription P in D escription GND C HROMA GND LUMA S - Video connector. C - Video connector. P in D escription D ATA IN / OUT 32 User’s Guide Description of Warranty Advan warrants that the goods the goods sold hereunder will be free of defects in materials and workmanship, and such goods will substantially conform to the specifications furnished by Advan, and to any drawings or specifications furnished to Advan by the Buyer if approved by Advan. This warranty shall be effective only if Advan receives notice of such defect or nonconformance during the period of the warranty. Advan sole and exclusive the Advan product(s) with refurbished units provide a credit to buyer in the amount of the purchase price. Commencement and Duration of Warranty The warranty period begins on the date of shipment from Advan. The goods sold hereunder are warranted for a period of 18 months from date of shipment unless otherwise agreed to by Buyer and Advan. No extension of the warranty will be given during the time the goods are in Advan possession. Place of Repair or Replacement In order to obtain service under this warranty, Buyer must notify Advan of the defect before expiration on the warranty period, and request a “Return Material Authorization Number.” If the configuration has been modified in any manner, the product must be returned to its original configuration before any warranty service will be perfomed by Advan. No goods are to be returned to Advan without prior authorization. Buyer will be responsible for packaging and shipping the defective goods to the Advan Service Facility with shipping charges prepaid. Limitation of Warranty Monitor: For 18 months after the date of purchase, ADVAN or its Authorized Service Centers, will repair or replace if defective in material or workmanship. This Limited Warranty does not include cleaning, or damage caused by accident, neglect, misuse or improper installation or operation, any damage caused from service, maintenance, modifications or tampering by anyone other than an ADVAN Authorized Service Representative, or by the use of supplies, consumable items and conditions beyond the control of ADVAN, such as common carrier provided equipment and/or facilities, operation of ADVAN product in excess of the specifications or with the Serial Number or Rating label removed. AMM213TD 33 ADVAN DISCLAIMS ALL OTHER WARRANTIES EXPRESS OR IMPLIED INCLUDING, WITHOUT LIMITATION, ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR PARTICULAR PURPOSE, EXCEPT TO THE EXTENT THAT ANY WARRANTIES IMPLIED BY LAW CANNOT BE VALIDLY WAIVED. No oral or written information or advice given by ADVAN, its authorized service center, distributors, dealers, agents or employees, shall create another warranty or modify this warranty. This warranty states ADVAN’s entire liability and your exclusive remedy against ADVAN for any failure of the ADVAN’s product to operate properly. Neither ADVAN nor anyone else involved in the development, production, or delivery of this product shall be liable for any indirect, incidental, special consequential, exemplary, or punitive damages, including lost profits, arising from the use of or inability to consequential or incidental damages, the above limitation may not apply to you. This Limited Warranty gives you special legal rights and you may also have other right, which vary from State to State. Installation Advan makes no warranty with respect to any installation of Advan’s product(s) by Advan, any authorized dealer, or any other person. Technical Assistance For technical assistance please call (510)490-1005 between 8:00 a.m. and 5:00 p.m. PST, Monday through Friday or email to support@advancorp.com with a description of your technical issues. Service If your Medical Monitor needs service, call Advan Customer Service / RMA at (510)490-1005 between 7:00 a.m and 4:00 p.m PST, Monday through Friday or fax to (510)490-1151. You will need the unit’s serial number and a brief description of the problem and where unit were purchased to receive a RMA number. If a service is required please return the product for service using the original shipping container with the RMA number included in package on the outside of the box. In order to protect ADVAN employees form potential health hazards, ADVAN requires that the RMA product be disinfected before returning to ADVAN for service. Any product not cleaned prior to shipment will be returned to the customer. Note: Returns will not be accepted without an assigned RMA number. In-transit damage is not covered by warranty. We suggest you always insure your shipment. Advan will only pay for the return shipment by surface transportation. It is the responsibility of the sender to prepay transportation charges. ADVAN INT’L CORP 47817 Fremont Blvd. Fremont, CA 94538 Tel : 510-490-1005 Fax : 510-490-1151 Web Page : http://www.advancorp.com
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : No Encryption : Standard V1.2 (40-bit) User Access : Print, Modify, Copy, Annotate, Fill forms, Extract, Assemble, Print high-res Create Date : 2007:10:19 10:41:13-07:00 Subject : Untitled-1 Author : alanyu Modify Date : 2007:11:30 10:47:47+09:00 XMP Toolkit : 3.1-701 Producer : Acrobat Distiller 7.0 (Windows) Keywords : Creator Tool : Adobe PageMaker 7.0 Format : application/pdf Creator : alanyu Description : Untitled-1 Title : Untitled-1 Document ID : uuid:dc2bb005-a6ea-4a51-b805-26cf9c0c0f6b Instance ID : uuid:9f647a30-9367-4ecb-93e2-5b927002fbd0 Page Count : 37EXIF Metadata provided by EXIF.tools