BBM Electronics Group 6KLTX Wireless microphone transmitter belt pack User Manual S6000 belt instructions V1 2

Download:
Mirror Download [FCC.gov]
Document ID	391052
Application ID	t4WE89xVZzOp8JgKuZGxug==
Document Description	Instructions
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	19.78kB (247216 bits)
Date Submitted	2004-01-22 00:00:00
Date Available	2004-01-22 00:00:00
Creation Date	2004-01-15 08:10:26
Producing Software	Acrobat Distiller 5.0 (Windows)
Document Lastmod	2004-01-15 08:10:26
Document Title	Microsoft Word - S6000 belt instructions V1-2.doc
Document Creator	PScript5.dll Version 5.2
Document Author:	Administrator

Introduction:
Thank you for purchasing your Trantec S6000 Beltpack.
If you require additional copies of these instructions, they can be
http://www.trantec.co.uk, along with other information about the Trantec range.
•
obtained
from
our
web
site,
Background Information:
The S6000 Beltpack is a microprocessor controlled UHF transmitter, which can operate on up to 64 different
channels. The exact selection of channels available will depend on how your system has been configured. The ability
to change operating channel will be immediately useful when configuring for a multi-user site or where the presence
of other radio microphone users may cause problems when using a fixed channel system.
•
General Radio Microphone Operating Guidelines:
Always try to locate the receiver as close as possible to the transmitter, as this minimises the chance of there being
any drop out. Although this is most unlikely with a diversity system, the greater the transmitting range, the greater the
chance of problems. Always try to ensure a line of sight signal path between the transmitter and receiver - obstacles
such as walls can significantly reduce the radio signal strength. Obviously the transmitter and receiver must be on
the same channel. If you are using more than one system simultaneously, choose a set of intermodulation free
frequencies. Please refer to the channel listings at the end of these instructions as a guide to finding a suitable set of
frequencies. Note that although your system may be capable of operating on channels other than the license exempt
ones, it is illegal to do this in the UK without first obtaining a license. It is wise to avoid placing the receiver near to
computer or mobile telephone equipment, as this can create unwanted radio interference. As emphasised in these
instructions, always operate any radio microphone system with its antennas fully extended. Always test a radio
microphone system in the location where it is to be used by doing a ‘walk test’. This is where the system is tested as
the transmitter is walked around the area in which it is to be used. This will normally show up any problem areas,
allowing you to try a new receiver location. By adjusting the location of the receiver, or even just the alignment of its
antennas, it should be possible to obtain trouble free operation over the desired area, provided that it is not too large
to exceed the transmitter’s range, which is typically around 100m.
•
Guarantee:
All Trantec products are guaranteed for a period of one year from date of purchase against defects in materials and
workmanship. In the event of a claim under guarantee the system should be returned to your dealer in its original
packaging and with proof of purchase. Defects caused by modification, misuse or accident are not covered by the
guarantee.
Due to our continual policy of research and development we reserve the right to alter specifications without prior
notice.
Trantec Systems
BBM Electronics Group Ltd
Kestrel House
Garth Road
Morden
Surrey
SM4 4LP
UK
Tel: +44 (020) 8330 3111
Fax: +44 (020) 8330 3222
E-Mail: enquiries@trantec.co.uk
Web: http://www.trantec.co.uk
Page 2 of 6 S6000 Beltpack Instructions V1.0
S6000L Transmitter Set-up:
Manual adjust
Audio input
Power LED
ON
OFF
POWER
Infra red p
Power switch
LCD
Battery compartment
RF input
Screw the external antenna into the antenna connector on the top of the beltpack. Under no circumstances should
the length of a wire antenna be shortened, coiled up or wrapped with the audio lead as this will reduce the
performance of the radio system.
Insert the Lemo connector for the lapel microphone into the audio connector using the two red idents as a polarity
guide. Do not twist this connector. Keep the audio lead and the antenna separated at all times.
Open the battery compartment of the beltpack and insert a 1.5v ‘AA’ alkaline battery this should be inserted negative
end first, positive end toward the battery compartment door.
Switch on the beltpack using the switch on the top. The LED will light and the LCD will display the current gain setting
followed by the current loaded frequency.
•
Changing the Transmitting Frequency
Next to the LCD there is a screwdriver adjust, this is actually a dual function digital switch. When the beltpack is
initially turned the LCD first shows the current gain then the current loaded frequency. For approximately 10 seconds
the decimal point will flash, during this flashing period the user can use a screwdriver to adjust the frequency. The
decimal point will then stop flashing and the screwdriver adjust can now be used to configure the gain. The operating
frequency is stored permanently in non-volatile memory so it will remain the same even if the battery is replaced.
The frequencies loaded into the transmitter can be changed through the infrared port on either the receiver front
panel, or a PALM pilot both these are described later
The exact selection of channels available will depend on how the transmitter has been programmed in the factory. It
can contain up to 64 unique channels, but your transmitter will not necessarily contain this many channels.
•
Changing the gain
After the decimal point has stopped flashing the screwdriver adjust can now be used to configure the gain. The LCD
displays between 0 and 9, 0 being the minimum gain and 9 the maximum. The gain is stored permanently in nonvolatile memory so it will remain the same even if the battery is replaced
•
Optimising the Gain of your system:
In order to achieve the best possible audio performance from your radio system, it is worth spending a few minutes
setting the optimum gain level.
Adjust the gain of your transmitter, as described in the appropriate section. The optimum setting for this will be found
by first adjusting the transmitter gain so that when the maximum audio signal expected just lights the receiver AF bar
display to the +3 dB. If this level is surpassed then distortion is likely. The optimum setting will vary according to who
is using the microphone and how close the microphone is placed to the mouth.
Page 3 of 6 S6000 Beltpack Instructions V1.0
Once the transmitter gain is optimised, it is necessary to match the receiver’s output level to your mixing desk or PA
system.
•
Battery monitoring
The battery voltage is displayed on the LCD of the transmitter and is shown in three segments, the first goes out
when 60% of the battery life has expired, the second goes out at 80%. The battery level is encoded with as a very
low frequency signal and sent over the RF link so the actual battery voltage can be monitored from the receiver.
•
Using a S5000 transmitter with the S6000 receiver
Both the S5000 and S6000 transmitters are high quality and will work well with the S6000 receiver. As S6000
beltpack has been designed using the latest circuit techniques, this means we had to make some fundamental
changes to the operation of the companding (noise reduction) circuitry. In order to make the S6000 receiver audio
circuit compatible with S5000 we have included both types of companding circuit on each receiver. The other
difference between the two types is the battery monitoring, the S5000 has a single threshold when the battery status
is deemed to be low, whilst the S6000 continually reports the actual voltage level throughout the life of the battery.
Either type of transmitter being used can be selected for each receiver from the monitor interface.
•
Differences between S5000 and S6000 transmitters
Apart from the obvious size difference between the two units the circuits vary fundamentally in the following
ways: -
Operating frequency range
Battery type
Battery life
Frequency setup
Battery monitoring
Tone grip
Control disable
Power disable
Smart power circuit
RF power switch
S5000
24 MHz
1 x "PP3" cell
8 hours
Data cable
Threshold
32 kHz
no
no
no
no
S6000
70 MHz
1 x "AA" cell
8 hours
Infra red
Full range
32 kHz
yes
yes
yes
yes
For S6000LTX Transmitter Lemo Connector Details see Appendix 2
Page 4 of 6 S6000 Beltpack Instructions V1.0
Appendix 1.
S6000LTX Transmitter Lemo Connector Details:
Internal View
Pin Connections : Pin 1 Ground, Pin 2 +9v, Pin 3 Audio/+9v, Pin 4 Audio
Trantec TS259:
Trantec TS33:
Trantec TS44:
Pin 1 Screen
Pin 2 Not connected
Pin 3 White
Pin 4 Not Connected
Pin 1 Screen
Pin 2 Not Connected
Pin 3 White and Red
Pin 4 Not Connected
Pin 1 Screen
Pin 2 Red
Pin 3 Not Connected
Pin 4 White
Trantec TS55:
Trantec TS912:
Sennheiser MKE2:
Pin 1 Screen
Pin 2 Red
Pin 3 Not Connected
Pin 4 White
Pin1 Screen
Pin 2 Red
Pin 3 Not Connected
Pin 4 Yellow
Pin 1 Screen
Pin 2 Not connected
Pin 3 Red
Pin 4 Not Connected
Sony ECM77:
Sanken COS-11PT:
Beyer MCE5:
Pin 1 Screen plus Clear
Pin 2 Not Connected
Pin 3 Red
Pin 4 Not Connected
Pin 1 Screen
Pin 2 Black
Pin 3 Not Connected
Pin 4 White
Pin 1 Screen
Pin 2 Red
Pin 3 Not Connected
Page 5 of 6 S6000 Beltpack Instructions V1.0
Appendix 2.
Frequency Guide:
See web site for US freq plans.
•
Technical Specifications
Frequency Range: 590-806MHz excluding 608-614Mhz.
Available in 3 Groups 734-806, 662-734, 590-662MHz
Frequency Arrangement: 64 Frequencies on a 25kHz grid
Output Power: 13dBm @ 50 Ohm
Nominal Deviation: 15
RF Harmonic & Spurious Radiation: < -45dBC
Frequency Stability: < 50ppm -30 – 50degrees C
Power Consumption: 150mA, 1.5V “AA” Alkaline Battery
Battery End Point: 1.0V
Operating Time: 8 hours (Typical)
AF Frequency Response: 70Hz-18kHz
Audio Input: LEMO FGG304, Pin 1 - 0v, Pin 2 - DC 9v Bias, Pin 3 - Audio + Plus, Pin 4 - AC Coupled Audio
AF Gain: 10 Step Gain (Input level 0dB to -22dB)
Dimensions: 50 x 68 x 20
Weight: 68g
Regulatory information: Fully meets requirements of FCC pts 74 subpart H
•
Accessories
Spare Lemo connector (audio)
Trantec part number xxxx
Spare Lemo connector (RF)
Trantec part number xxxx
Sennheiser MKE2 lavalier microphone – Lemo -
Trantec Part number xxxx
¼ wave whip antenna
Trantec part number xxxx
Leather carry case for transmitter
Trantec part number XXXX
Page 6 of 6 S6000 Beltpack Instructions V1.0

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.3
Linearized                      : No
Create Date                     : 2004:01:15 08:10:26Z
Modify Date                     : 2004:01:15 08:10:26Z
Page Count                      : 6
Creation Date                   : 2004:01:15 08:10:26Z
Mod Date                        : 2004:01:15 08:10:26Z
Producer                        : Acrobat Distiller 5.0 (Windows)
Author                          : Administrator
Metadata Date                   : 2004:01:15 08:10:26Z
Creator                         : Administrator
Title                           : Microsoft Word - S6000 belt instructions V1-2.doc

EXIF Metadata provided by EXIF.tools