Users Manual
Warranty FCC Caution Statements:
• Any damage or defects caused by a failure to follow the instruction which relate to
this device or as the result of an accident, abuse, misuse, misapplication, product
modication, improper voltage or current, acts of God, shipping damages or loss, or
damage caused by service performed by anyone other than our company are
expressly excluded from the warranty stated below.
• We are not under any obligation to support the device for all operating
environments, including but not limited to, interoperability with all current and/or
future versions of software or hardware.
• Please contact the dealer for any warranty or customer support services.
This transmitter must not be co-located or operating in conjunction with any other
antenna or transmitter.
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that may
cause undesired operation.
NOTE: This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment o and on, the
user is encouraged to try to correct the interference by one of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit dierent from that to which the
receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Caution: Any changes or modications not expressly approved by the party
responsible for compliance could void the user's authority to operate this equipment.
©2016 BBPOS Limited. All rights reserved. BBPOS and Chipper™ are either trademark or registered trademarks of
BBPOS Limited. iOS is the trademark of Apple Inc. Android™ is a trademark of Google Inc. Windows® is registered
trademark of Microsoft Corporation in the United States and/or other countries. All details are subject to change
without prior notice.
Room 1602, 16/F, Tower 2, Nina Tower, No. 8 Yeung Uk Road, Tsuen Wan, Hong Kong
www.bbpos.com
Need Help?
E: sales@bbpos.com | T: +852 3158 2585
Revise v.2 / 20160704
• Ensure to turn on the Bluetooth® function of your smartphone or tablet before use.
• Please fully charge your Chipper™ BT before use.
• Please ensure magstripe/EMV chip of the card is facing the right direction when
swiping or inserting card.
• Don’t drop, disassemble, tear, open, crush, bend, deform, puncture, shred,
microwave, incinerate, paint, or insert foreign object into the device. Doing any of
which will void the Warranty.
• Don’t immerse the device into water and place near washbasins or any wet
locations. Don’t spill any food or liquid on the device. Don’t attempt to dry the
device with external heat sources, such as microwave or hair dryer.
• Don’t use any corrosive solvent or water to clean the device. Recommend using dry
cloth to clean the surface only.
• Don’t use any sharp tools to point the internal components or connectors, doing
which may lead to malfunction and void the Warranty.
• Don’t try to disassemble the device to repair. Please contact your dealer for repair
and maintenance.
Cautions & Important Notes TroubleshootingProduct Specications
Problems Recommendations
• Please press the power on button to restart your device.
• Please check if you can nd the device’s “Serial Number”
(Shown on the back of device) in the “Scanned Device List” of
your smartphone or tablet.
• Please press the power on button to turn on the device again.
The device will automatically connect with your smartphone or
tablet again.
• The device may be at lower battery level, please use the USB
cable to recharge it, then retry.
• Please ensure the device or smartphone/tablet is within the
reception range.
Device cannot be paired
Device cannot read your
card successfully
Problems Recommendations
• Please press the power on button to turn on the device again.
The device will automatically connect with your smartphone or
tablet again.
• The device may be at lower battery level, please use the USB
cable to recharge it, then retry.
• Please ensure the device or smartphone/tablet is within the
reception range.
• Please ensure the Bluetooth® function of your smartphone or
tablet is turned on.
• Please check the version of your operating system is supported
for this device’s operation.
Device lost the
connection with your
smartphone or tablet
when the device is
auto-o.
• Please use a paper clip to press the reset button at the bottom
for reboot.
Device has no response
Device does not work
with your phone or
tablet
• Please check if the device has power when operating and
ensure devices are connected.
• Please check if the application instructs to swipe or insert card.
• Please ensure there is no obstacle in the card slots.
• Please check if the magstripe or chip of the card is facing the
right direction when swiping or inserting card.
• Please ensure your phone/tablet is supported model for this
device’s operation.
• Please swipe or insert card with a more constant speed.
Device cannot read
your card successfully
Functions • EMV/PBOC Chip Card Reader
(ISO 7816 Compliant Class A, B, C card)
• Magnetic Stripe Card Reader
Dual tracks (track 1 & 2 or track 2 & 3)
Communication Interface Bluetooth® 4.0, USB
Power & Battery Lithium polymer rechargeable battery 125mAH, 3.7V
Charging Via micro USB
Swipe Speed 15cm - 100cm/sec
LED Indicator Operating – green light ashing
Low battery level – red light ashing
Charging – red light ON
Fully charged – green light ON
Support Operating System Android 2.1 or above, iOS 6.0 or above
Windows Phone 8, MS Windows
Product Size 61.8mm (W) x 44.5mm (H) x 14.2mm (D)
Product Weight 29.8g
Operating Temperature 0°C – 45°C (32°F – 113°F)
Operating Humidity Max 95%
Storage Temperature -20°C – 55°C (-4°F – 131°F)
Storage Humidity Max 95%