BESS 13EAR9T PROXIMITY ACCESS READER User Manual BSR10 Manual pdf 2013 01 08 ai

BESS (Best Security Solutions) PROXIMITY ACCESS READER BSR10 Manual pdf 2013 01 08 ai

User Manual

3. SPECIFICATION Read Range Reading Format Micro-Processor Failure Correction Input Output LED Indicator Beeper Operating Temp. Storage Temp. Power Spec. Plastic Material Potting Material Dimension Weight CertificationUpto 3"(7.6cm) depending on Card Type13.56MHz MIFARE Classic, MIFARE Plus, NFCISO14443 Type-A/Type-B, ISO15693 (optional)32bit Micro-ProcessorBuilt-in WATCH-DOG TimerLED Control, BEEP Control, WIEGAND Select34Bit/26Bit Wiegand, RS232, RS485 (optional)4 x 2-Color LEDS, LOGO LED (optional)80dB Piezo Buzzer-31oF ~ 149oF (-35oC ~ 65oC)-49oF ~ 176oF (-45oC ~ 80oC)DC12V, max.150mAPoly CarbonateEpoxy PottingW2.20"xH3.35"xD0.59"(W56xH85xD15mm)2.2oz (62g)FCC, CE, KCC5. INSTALLATION - Drill 2 x M3 holes 2.36"(60mm) apart in vertical and drill a 1/2"(13mm) hole for the cable in the middle of 2 x M3 holes. - Connect all necessary wires of SMD Connector to ACU device. - Plug in SMD Connector to Reader Module and put DC power to the reader and test the reader is working fine. - Fix the Reader Module to the wall using 2 screws or bolts. How to attach Top Bezel to the Reader Module - Attach Top Bezel to Reader Module from the bottom side and push top side until the Top Bezel locked to Reader Module. - Peel off protection tape from the window of Top Bezel. How to detach Top Bezel from the Reader Module - Insert a toothpicker to small hole on the buttom side of Top Bezel. - Push toothpicker to upper side until the Top Bezel unlocked.REDBLACKGREENWHITEGRAYORANGEYELLOWBLUEPURPLEBROWNPower Input, DC +12VPower Ground, GNDWiegand Output, DATA_D0Wiegand Output, DATA_D1RS232 Input, RS232-RXRS232 Output, RS232-TXLED Control Input, Active to GNDBEEPER Control Input, Active to GNDWiegand Select Input, Open=34BIT, GND=26BITBOOT Input, Open=RUN, GND=BOOT MODE4. WIRE COLOR TABLE6. OPERATION POWER ON AND INITIALIZATION - Put DC12V power to the reader, it will make 3 beep sounds with flashing Red-Green-Red LEDs alternately. - Red LEDs will flash continueously indicating reader is ready. CARD READING - Approach a card to the reader and it makes a beep sound with flashing Green LEDs, simultaneously Wiegand data and RS232 data will be sent out to connected ACU. - The reader has OTR(One Time Reading) function therefore the same card can not be read twice unless the card is away from the read range of the reader. SELECT WIEGAND OUTPUT FORMAT (34bit or 26bit) - The reader has a Wiegand Select Input port (purple wire). - The purple wire stays OPEN(No Connection), the reader will set 34bit Wiegand output format. - When the purple wire puts to ground(GND) before power ON, the reader will set 26bit Wiegand output format. - If you want to have 26bit Wiegand output format, the purple wire always puts to ground(GND). LED CONTROL - The reader has a LED Control Input port (yellow wire). - While the yellow wire puts to ground(GND), all Green LEDs lit. BEEPER CONTROL - The reader has a BEEPER Control Input port (blue wire). - While the blue wire puts to ground(GND), Beeper makes sound. BOOT MODE - The reader has a BOOT Input port (brown wire). - When the brown wire puts to ground(GND) before power ON, the reader will enter to BOOT MODE when it powered ON. - BOOT MODE is used to upgrade F/W of the reader therefore the brown wire always be OPEN(No Connection).7. OUTPUT FORMAT and TIMING 34bit Wiegand Output Format - Bit_1 : EVEN parity of Bit_1 to Bit_17 - Bit_2 ~ Bit_33 : 32bit Card ID Number(4bytes of CSN) - Bit_34 : ODD parity of Bit_18 to Bit_34 26bit Wiegand Output Format - Bit_1 : EVEN parity of Bit_1 to Bit_13 - Bit_2 ~ Bit_25 : 24bit Card ID Number(3bytes of CSN) - Bit_26 : ODD parity of Bit_14 to Bit_26 Timing Diagram RS232 Output Format - 9,600bps/8 Data bit/1 Stop bit/Parity None RS232 Data Format(Total 13bytes) Ch1 Ch2 ~ Ch11 Ch12 CH13 1byte 10bytes 1byte 1byte Start Ch Card ID Number End Ch CRC (0x02h) (0x30h~0x39h) (0x03h) (XOR) Ch1 : Start Character, 1 byte (0x02h) Ch2~Ch11 : Card ID Number, 10 bytes (0x30h~0x39h) Ch12 : End Character, 1 byte (0x03h) Ch13 : CRC, 1 byte (XOR of Ch1~Ch12)8. FCC REGISTRATION INFORMATIONFCC REQUIREMENTS PART 15Caution: Any changes or modifications in construction of this device which are not expressly approved by the manufacturer for compliance could void the user's authority to operate the equipment.NOTE: This device complies with Part 15 of the FCC Rules.Operation is subject to the following two conditions:1. This device may not cause harmful interface, and2. This device must accept any interference received, including inter- ference that may cause undesired operation.This equipment has been tested and found to comply with the limits fora Class B Digital Device, pursuant to Part 15 of the FCC Rules. These limits are designed to this equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accor-dance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the radio or television off and on, the user is encouraged to try to correct interference by one or more of the following measures.1. Reorient or relocate the receiving antenna.2. Increase the separation between the equipment and receiver.3. Connect the equipment into an outlet on another circuit.4. Consult the dealer or an experienced radio/TV technician for help.9. Warranty and ServiceBESS Smart Card Reader warranty is 5 years from the shipping date.The following warranty and service information applies to all customers.For the information regard the service, contact your local distributoror suppliers. To obtain in or out of warranty service, please prepay shipment and return the product to the facility listed below.BESS Corp., Service Center#1313 Hyosung Intellian,426 Gangseo-ro, Gangseo-gu,SEOUL, KOREA 157-030Tel.: (+82) 704 045 0058E-mail: service@bess.ccWeb-site: www.bess.ccPlease use the original container, or pack the unit(s) in a sturdy carton with sufficient packing to prevent damage, include following information:1. A proof-of-purchase indicating model number and date of purchase.2. Bill-to address3. Ship-to address4. Number and description of units shipped.5. Name, phone number and email address of person to contact.6. Reason for return and description of the problem.NOTE: Damage occurring during shipment is deemed the responsibility of the carrier, and claims should be made directly to the carrier.USER'S MANUALSMART CARD READER MODEL: BSR-10bess2. FEATURES Reading Format - MIFARE Classic & MIFARE Plus, ISO14443 Type-A & Type-B Cards - NFC (Smart Phones), ISO15693 & OCTOPUS Cards (Optional) Output - 34Bit/26Bit WIEGAND Output (Selectable) & RS232 Serial Output Input - WIEGAND Select Input, BEEPER Control Input, LED Control Input Easy Installation - FIT to European Gangbox Onsite F/W Upgrade - BOOT Mode to Upgrade F/W using Serial Port Robust Design - SMART & TINY Design - INNER Module Fully Potted by Hard Epoxy - MULLION & DOOR FRAME Mount1. IDENTIFYING SUPPLIED PARTS Please unpack and check the contents of the box.Best Security SolutionsBest Security SolutionsbessbessReader Module Cable and Screws Manual2.36"(60mm)2 x M3 Hole1/2" Hole2 x M3 ScrewsReader Module Top BezelDrill HolesbessBest Security SolutionsWebsite: www.bess.cc Email: mikeyoo@bess.ccPhone: (+82) 70 4045 0058 Mobile: (+82) 10 6509 6533#1313 Hyosung Intellian, 426 Gangseo-roGangseo-gu, Seoul, KOREA 157-030(우)157-030 서울 강서구 강서로 426, 효성인텔리안 1313 호

Navigation menu