BESS 13EAR9T PROXIMITY ACCESS READER User Manual BSR10 Manual pdf 2013 01 08 ai

Download:
Mirror Download [FCC.gov]
Document ID	1910128
Application ID	VdTYBijkJecwHDASWFd1zA==
Document Description	User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	6.66kB (83301 bits)
Date Submitted	2013-03-04 00:00:00
Date Available	2013-03-04 00:00:00
Creation Date	2013-02-27 15:44:36
Producing Software	Acrobat Distiller 8.0.0 (Windows)
Document Lastmod	2013-02-27 15:44:36
Document Title	BSR10-Manual-pdf-2013_01_08.ai
Document Creator	PScript5.dll Version 5.2
Document Author:	Mike Yoo

USER'S MANUAL
SMART CARD READER
MODEL: BSR-10
1. IDENTIFYING SUPPLIED PARTS
3. SPECIFICATION
Please unpack and check the contents of the box.
bess
Best Security Solutions
Reader Module
Cable and Screws
Upto 3"(7.6cm) depending on Card Type
13.56MHz MIFARE Classic, MIFARE Plus, NFC
ISO14443 Type-A/Type-B, ISO15693 (optional)
32bit Micro-Processor
Micro-Processor
Failure Correction Built-in WATCH-DOG Timer
LED Control, BEEP Control, WIEGAND Select
Input
34Bit/26Bit Wiegand, RS232, RS485 (optional)
Output
4 x 2-Color LEDS, LOGO LED (optional)
LED Indicator
80dB
Beeper
o Piezo Buzzer
-31oF ~ 149oF (-35oC ~ 65oC)
Operating Temp.
-49 F ~ 176 F (-45 C ~ 80 C)
Storage Temp.
DC12V, max.150mA
Power Spec.
Poly Carbonate
Plastic Material
Epoxy Potting
Potting Material
W2.20"xH3.35"xD0.59"(W56xH85xD15mm)
Dimension
2.2oz (62g)
Weight
FCC, CE, KCC
Certification
Read Range
Reading Format
Manual
5. INSTALLATION
- Drill 2 x M3 holes 2.36"(60mm) apart in vertical and drill a
1/2"(13mm) hole for the cable in the middle of 2 x M3 holes.
- Connect all necessary wires of SMD Connector to ACU device.
- Plug in SMD Connector to Reader Module and put DC power
to the reader and test the reader is working fine.
- Fix the Reader Module to the wall using 2 screws or bolts.
How to attach Top Bezel to the Reader Module
- Attach Top Bezel to Reader Module from the bottom side and
push top side until the Top Bezel locked to Reader Module.
- Peel off protection tape from the window of Top Bezel.
How to detach Top Bezel from the Reader Module
- Insert a toothpicker to small hole on the buttom side of Top Bezel.
- Push toothpicker to upper side until the Top Bezel unlocked.
2. FEATURES
bess
7. OUTPUT FORMAT and TIMING
6. OPERATION
POWER ON AND INITIALIZATION
- Put DC12V power to the reader, it will make 3 beep sounds with
flashing Red-Green-Red LEDs alternately.
- Red LEDs will flash continueously indicating reader is ready.
CARD READING
- Approach a card to the reader and it makes a beep sound with
flashing Green LEDs, simultaneously Wiegand data and RS232
data will be sent out to connected ACU.
- The reader has OTR(One Time Reading) function therefore the
same card can not be read twice unless the card is away from
the read range of the reader.
34bit Wiegand Output Format
- Bit_1
: EVEN parity of Bit_1 to Bit_17
- Bit_2 ~ Bit_33 : 32bit Card ID Number(4bytes of CSN)
- Bit_34
: ODD parity of Bit_18 to Bit_34
26bit Wiegand Output Format
- Bit_1
: EVEN parity of Bit_1 to Bit_13
- Bit_2 ~ Bit_25 : 24bit Card ID Number(3bytes of CSN)
- Bit_26
: ODD parity of Bit_14 to Bit_26
Timing Diagram
BEEPER CONTROL
- The reader has a BEEPER Control Input port (blue wire).
- While the blue wire puts to ground(GND), Beeper makes sound.
BOOT MODE
- The reader has a BOOT Input port (brown wire).
- When the brown wire puts to ground(GND) before power ON,
the reader will enter to BOOT MODE when it powered ON.
- BOOT MODE is used to upgrade F/W of the reader therefore
the brown wire always be OPEN(No Connection).
RED
BLACK
GREEN
WHITE
GRAY
ORANGE
YELLOW
BLUE
PURPLE
BROWN
Power Input, DC +12V
Power Ground, GND
Wiegand Output, DATA_D0
Wiegand Output, DATA_D1
RS232 Input, RS232-RX
RS232 Output, RS232-TX
LED Control Input, Active to GND
BEEPER Control Input, Active to GND
Wiegand Select Input, Open=34BIT, GND=26BIT
BOOT Input, Open=RUN, GND=BOOT MODE
RS232 Output Format
- 9,600bps/8 Data bit/1 Stop bit/Parity None
Ch1
1byte
Start Ch
(0x02h)
Ch1
Ch2~Ch11
Ch12
Ch13
Ch2 ~ Ch11
10bytes
Card ID Number
(0x30h~0x39h)
Ch12
1byte
End Ch
(0x03h)
CH13
1byte
CRC
(XOR)
: Start Character, 1 byte (0x02h)
: Card ID Number, 10 bytes (0x30h~0x39h)
: End Character, 1 byte (0x03h)
: CRC, 1 byte (XOR of Ch1~Ch12)
2 x M3 Screws
1/2" Hole
Drill Holes
Reader Module
Top Bezel
9. Warranty and Service
FCC REQUIREMENTS PART 15
BESS Smart Card Reader warranty is 5 years from the shipping date.
The following warranty and service information applies to all customers.
For the information regard the service, contact your local distributor
or suppliers. To obtain in or out of warranty service, please prepay
shipment and return the product to the facility listed below.
Caution: Any changes or modifications in construction of this device
which are not expressly approved by the manufacturer for compliance
could void the user's authority to operate the equipment.
NOTE: This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
1. This device may not cause harmful interface, and
2. This device must accept any interference received, including interference that may cause undesired operation.
1. Reorient or relocate the receiving antenna.
2. Increase the separation between the equipment and receiver.
3. Connect the equipment into an outlet on another circuit.
4. Consult the dealer or an experienced radio/TV technician for help.
RS232 Data Format(Total 13bytes)
2 x M3 Hole
8. FCC REGISTRATION INFORMATION
This equipment has been tested and found to comply with the limits for
a Class B Digital Device, pursuant to Part 15 of the FCC Rules.
These limits are designed to this equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will
not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the radio or television off and on, the user is encouraged to try to
correct interference by one or more of the following measures.
SELECT WIEGAND OUTPUT FORMAT (34bit or 26bit)
- The reader has a Wiegand Select Input port (purple wire).
- The purple wire stays OPEN(No Connection), the reader will
set 34bit Wiegand output format.
- When the purple wire puts to ground(GND) before power ON,
the reader will set 26bit Wiegand output format.
- If you want to have 26bit Wiegand output format, the purple wire
always puts to ground(GND).
LED CONTROL
- The reader has a LED Control Input port (yellow wire).
- While the yellow wire puts to ground(GND), all Green LEDs lit.
4. WIRE COLOR TABLE
2.36"(60mm)
Reading Format
- MIFARE Classic & MIFARE Plus, ISO14443 Type-A & Type-B Cards
- NFC (Smart Phones), ISO15693 & OCTOPUS Cards (Optional)
Output
- 34Bit/26Bit WIEGAND Output (Selectable) & RS232 Serial Output
Input
- WIEGAND Select Input, BEEPER Control Input, LED Control Input
Easy Installation
- FIT to European Gangbox
Onsite F/W Upgrade
- BOOT Mode to Upgrade F/W using Serial Port
Robust Design
- SMART & TINY Design
- INNER Module Fully Potted by Hard Epoxy
- MULLION & DOOR FRAME Mount
BESS Corp., Service Center
#1313 Hyosung Intellian,
426 Gangseo-ro, Gangseo-gu,
SEOUL, KOREA 157-030
Tel.: (+82) 704 045 0058
E-mail: service@bess.cc
Web-site: www.bess.cc
Please use the original container, or pack the unit(s) in a sturdy carton
with sufficient packing to prevent damage, include following information:
1. A proof-of-purchase indicating model number and date of purchase.
2. Bill-to address
3. Ship-to address
4. Number and description of units shipped.
5. Name, phone number and email address of person to contact.
6. Reason for return and description of the problem.
NOTE: Damage occurring during shipment is deemed the responsibility
of the carrier, and claims should be made directly to the carrier.
bess
Best Security Solutions
#1313 Hyosung Intellian, 426 Gangseo-ro
Gangseo-gu, Seoul, KOREA 157-030
(우)157-030 서울 강서구 강서로 426, 효성인텔리안 1313 호
Website: www.bess.cc
Email: mikeyoo@bess.cc
Phone: (+82) 70 4045 0058 Mobile: (+82) 10 6509 6533

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : Yes
XMP Toolkit                     : Adobe XMP Core 4.0-c316 44.253921, Sun Oct 01 2006 17:14:39
Producer                        : Acrobat Distiller 8.0.0 (Windows)
Create Date                     : 2013:02:27 15:44:36+08:00
Creator Tool                    : PScript5.dll Version 5.2
Modify Date                     : 2013:02:27 15:44:36+08:00
Format                          : application/pdf
Title                           : BSR10-Manual-pdf-2013_01_08.ai
Creator                         : Mike Yoo
Document ID                     : uuid:fe6ea38b-b626-4be0-ac6d-3f3de721006b
Instance ID                     : uuid:d82a356c-6153-4483-bd79-07834d50b2c8
Page Count                      : 1
Author                          : Mike Yoo

EXIF Metadata provided by EXIF.tools