BOWFLEX Weight System Manual L0520846
User Manual: BOWFLEX BOWFLEX Weight System Manual BOWFLEX Weight System Owner's Manual, BOWFLEX Weight System installation guides
Open the PDF directly: View PDF 
.
Page Count: 23
| Download | |
| Open PDF In Browser | View PDF |
Assembly
FOR THE BOWFLEX
Manual
ULTIMATE
Includes Instructions for
Assembling
Bowflex Ultimate
Machines
®
Basic Assembly
Principles
Here are a few basic assembly tips that can make your assembly
these principles, you can simplify the process and save yourself
of the Bowflex Ultimate quick and easy. By using
some extra time and effort.
1. When you are using a ratchet to tighten a locknut on a bolt, use a close-ended
locknut. This will ensure that the locknut is fastened securely.
combination
wrench
to grip the
2. When you are having trouble placing a bolt between two separate pieces, you can get the bolt holes to line up by
gently lifting one of the pieces. You can also lift gently and look between the pieces for additional
help guiding the
bolt through the holes.
3. You can make the assembly
the step.
process
go faster by gathering
the pieces you need for each step prior to starting
4. As a general rule, and for all bolts and locknuts on your Bowflex Ultimate, turning toward the right will tighten,
turning toward the left will loosen. An easy way to remember this is by remembering
the expression, "Lefty loosey,
righty tighty."
Tools You Will Need
You will need the following tools to complete the assembly of your Bowflex Ultimate.
you can find them at any hardware or department
store for a reasonable price.
• 7/16" combination
wrench
• Flat blade
• 9/16" combination
wrench
• Rubber mallet
• An adjustable
wrench
• A socket wrench
• Phillips
• Utility
set
screw driver
Knife
• Scissors
screw driver
Finished
We've included
in the assembly
to these photos
Photos
a photograph
at the end of each step reF resenting the end result of that step
of your Bowflex Ultimate. If you have any doubt after finishing a step, refer
to see the accuracy of your assembly process.
This is m_exa,_ple of wh_t
the photos at fhe fisdsh qf
each step look like
Table
Bowflex
If you don't
of Contents
Ultimate
Parts Reference
Guide
................................
Pages 4-6
Assembling
the Bowflex
Ultimate
............................................
Assembling
the Bowflex
Ultimate
Lat Attachment
................ Pages 14-15
Assembling
the Bowflex
Ultimate
Leg Attachment
.............. Pages 16-19
Assembling
the Bowflex
Ultimate
T-Bar ..................................
Adding
extra Power
Rods ............................................................
Bowflex
Ultimate
Warranty
Bowflex
Ultimate
6-Week Satisfaction
Information
..................................
Guarantee
Pages 7-13
Page 19
Page 20
Pages 21-23
.................. Page 24
have these tools,
BOWFLEX
Ultimate
° Parts Reference
Guide
Lat Tower Assembly
/_Bent
Rod Cap
Lat Bar
Special
features
BOWFLEX
unique
ULTIMATE
to the
are the
special cable storage areas.
When the lat cables
are not
in
use they can be conveniently
tucked into the lat tower
Power Rods
assembly
as shown to the top
left. In addition,
the leg
extension
cables can be
_._
Rod Hook
Bench
Rod Box
Cable
Pul_y_
>
Lower Lat Crown
Leg Extension Assembly
(if so equipped)
\
Leg Extension
Seat
Adjustable
Pulley
System
Snap
Hook Ring_
Hand Gripl_
Ankle Cuff
Squat
Platform
Squat
Pufley
Squat Bar _
Foot Rest
Seat Raft
Leg Extension
Pulley
clipped intothe special clip
assemblylocated underthe
bench as shown in thepicture
to the left.
Leg Extension
Rollers
Base Unit Assembly
Parts List
Item No. Qty.
Part No.
Description
Item No. Qty.
Part No.
Description
1
1
10001
LOWER
39
1
90640
T-BAR
2
1
10002
LEFT MAIN
41
3
90149
SCREW,
1/4" X 1-1/2"
3
1
10003
RIGHT
44
4
10182
SCREW,
#10 X 3/4" SELF TAPPING
4
1
10004
SQUAT
FRAME
45
3
10183
SCREW,
#10 X 1" SELF DRILLING
5
1
10005
SQUAT
PLATFORM
46
5
10103
BOLT, 3/8" X 3/4"
6
1
10011
ADJUSTABLE
48
3
10107
BOLT, 3/8" X 2"
7
2
10012
ADJ, PULLEY SYST. BOLT SPACER
49
2
90193
BOLT, 3/8" X 2-1/2"
8
2
10074
ADJ, PULLEY
51
2
90139
BOLT, 3/8" X 3"
9
2
90177
PULLEY ASSEMBLY
52
4
10125
BOLT, 3/8" X 4-3/4"
10
1
10014
SEAT RAIL
53
1
10126
BOLT, 3/8" X 5"
11
1
10039
FOOT REST ASSEMBLY
54
30
90138
WASHER,
3/8"
13
1
10036
REAR LEG
55
6
90156
WASHER,
1/4"
14
1
10017
SEAT
57
13
90196
NUT, 3/8" NYLON
21
1
10015
INCLINE
BENCH
REST
58
1
90222
RAIL END CAP
22
1
10016
INCLINE
BENCH
REST BACK
59
1
90217
LEG PRESS
23
1
10049
ROD BOX w/RODS
73
2
10177
REAR LEG BOLT KEEPER
24
1
10044
ROD BOX FRAME
74
2
10178
LEG PRESS BOLT KEEPER
25
1
10019
BENCH
75
8
10125
3/8" x 3/4' SQUARE
26
1
10035
BENCH
76
1
10201
LOWER LAT CROWN
27
2
90215
ROD CABLE
32
2
10007
SQUAT CABLE
33
4
50334
SNAP HOOK
35
1
90650
48" BAR
36
2
10073
SQUAT STRAP
37
1
10075
LARGE THREADED
KNOB
38
2
90134
HAND
CUFF
I_AT TOWER
FRAME
MAIN
FRAME
ASSEMBLY
ASSEMBLY
PULLEY SYSTEM
SYST. LOCK KNOB
REST BRACKET
GRIP/ANKLE
w/STRAP
PHILLIPS
LOCK NUT
BELT
HEAD
BOLT
HEAD
Item
Item
#: 2
110001
Qty.:
#: 1
Item
1
#: 3
Item
#: 4
1
Qty.:
1
Qty.:
#: 10003
Part
#: 10004
Part
Qty.:
Part #: 10002
Part
Oescr:
Descr:
Left Main
Frame
Right Main
Frame
Descr:
Squat
Item
Frame
#: 5
Item
1
#: 10005
Descr:
#: 6
Qty.:
Part
Squat
Platform
1
#: 10011
Descr:
Adjustable
Assembly
Des_
Pulley
Ttem #: 7
Item
Qty.:
Qty.:
2
Dart #: 10012
Descr:
Adjustable
Pulley
#: 8
Item
2
Part #: 10074
Part
Descr:
Descr:
Adjustable
System
#: 9
Item
2
Qty.:
1
Qty.:
Part
#: 10014
Part
Qty.:
#: 90177
Pulley System
Lock Knob
Pulley
Descr:
Assembly
/
Q
Ttem #: 14
Item
Qty.:
Qty.:
1
#: 21
Dart #: 10017
Part
Descr:
Descr:
Seat
Item
1
#: 22
Qty.:
#: 10015
Incline
Descr:
Rest
ttem
#: 26
Oty.:
Item
1
Incline
Rest
#: 27
Qty.:
Item
2
#: 32
Qty.:
2
Dart #: 10035
Part #: 90215
Part
Descr:
Descr:
Rod
Cable
Descr:
Squat
Cable
Length:
43"
Length:
35"
Bench Rest
Bracket
Ttem #: 37
Item
Qty.:
Qty.:
1
#: 38
Part
Descr:
Descr:
Large
Threaded
#: 10007
Item
2
Dart #: 10075
Item
1
Part #: 10016
Bench
#: 90134
Hand Grip/
Ankle Cuff
#: 39
Qty.:
1
Part
#: 90640
Descr:
#: 10
T-Bar
Bench
Item
Seat Raft
1
Part
#: 10049
Item
=
Rod Box
Part
[
#: 33
Qty.:
#: 50334
Snap
Descr:
Rear Bench
Part
#: 10044
Rod Box
Frame
#: 35
Qty.:
1
Part
#: 90650
Item
1
Raft End
#: 25
Item
#: 36
Qty.:
2
Part
#: 10073
Descr:
#: 59
Qty.:
Part_90222
Descr:
#: 10036
Item
1
Hook
Item#:58
Qty.:
#: 24
Qty.:
Item
4
Descr:
Foot Rest
Descr:
w/Rods
Item
1
Part
%
#: 23
Back
#: 10039
Descr:
#: 13
Qty.:
1
Leg
Qty.:
Descr:
Item
#: 11
Part
Cap
Item
1
Descr:
Strap
#: 73
Qty.:
#: 90217
Squat
2
Part #: 10177
Leg Press
Belt
Descr:
Rear Leg Bolt
Keeper
Knob
Item
#: 74
Item
#: 76
Qty.:
2
Qty.:
Part#:
10178
Part #: 10201
Descr:
Leg Press
Descr:
Bolt
Keeper
1
Lower
Crown
Lat
02003
The N3utilus
Group,
hie ,V31/couvel: WA
98684 All rights
reserved
Note:
Drawings
are actual
size.
_ltty.:
Item
#: 41
Qty.:
Part
Serf Drilling
Screw
It_om #: 48
Item
2
#: 49
Item
3
#: 90149
Descr:
#: 44
Qty.:
1/4"X
PaP
rt #: 90193
1-1/2"
escr:
Phillips Head
Machine
Screw
Part
4
#: 10182
Descr:
3/8'lt' X 2-1/2"
#10 X 3/4"
Self Tapping
Screw
Item
#: 55
Qty.:
item
#: 51
Item
Qty.:
Qty.:
2
Part #: 90139
Descr:
Part
#: 46
6
#: 90156
Descr:
5
1/4"
Washer
Part #: 10103
Descr:
3/8"
Bolt
Item
X 3/4"
#: 52
Qty.:
3/8ol;X3"
4
Part #: 10125
Descr:
3/8"
Bolt
X 4-3/4"
Item #: 54
Qty.:
30
Item
Part
#: 90138
Qty.:
13
Part
#: 90196
Descr:
3/8"
Washer
#: 57
Descr:
Item
Item
Qty.:
#: 75
1
Part #: 10126
Descr:
3/8"
Bolt
3/8"
Nylon
#: 53
X 5"
Qty.:
Part
8
#: 10125
Descr:
3/8" X 3/4"
Square
Head Bolt
Nut
Lock
Step 1: LOWER MAIN FRAME ASSEMBLY
Locate the following for this step:
• Lower lat tower (Item #1)
• Left main frame (Item #2)
• Right main frame (Item #3)
• Two (2) 3/8X3" bolts (Item #51)
• Four (4) 3/8" washers (Item #54)
• Two (2) 3/8" nylon lock nuts (Item
#51)
[] Place the left main frame (Item #2) into the
saddle bracket of the lower lat tower (Item #1)
as shown in Figure A.
[] Insert a 3/8"X3" bolt (Item #51) with a
washer on it through the appropriate holes,
place a 3/8" washer (Item #54) and then a 3/8"
nylon lock nut (Item #57) on the bolt, hand
tighten at this time.
Figure
[] Place the mating right hand side of the main
frame (Item #3) next to the left side of the
frame in the lower lat tower saddle bracket
(Item #t) and repeat step above.
Note: Hand tighten
A
all bolts at this stage.
are in Box for
2 & this
Box step
4
I Components
Step 2: ADJUSTABLE
PULLEY SYSTEM
Locate the following for this step:
• Adjustable Pulley System (Item #6)
• Two (2) Adjustable Pulley System bolt spacers
(Item #7, twist tied to Adjustable Pulley System)
• Two (2) 3/8"X2-1/2" bolts (Item #49)
• Two (2) 3/8"X3/4" bolts (Item #46)
• Four (4) 3/8" washers (Item #54)
• Two (2) Adjustable Pulley System lock knobs (Item #8)
(_)
/
]
_4k_3r_
[] Remove twist ties from bolt spacers and slide Adjustable
Pulley System (Item #6) into main frame uprights as shown
in Figure B.
Note: The side with two large holes faces away from the machine.
[] Insert both 3/8"X2-1/2"
bolts (Item #49) with 3/8" washers
(Item #54) into chest slide spacers and hand tighten into the back
of lower lat tower (Item #1) (NOTE: DO NOT OVERTIGHTEN)
Note: Inserting
_
_ .&
®
the top bolt first will help you align the parts.
Figure
B
[] Hand tighten the 3/8"X3/4" bolts (Item #46) with 3/8" washers
(Item #54) into the uprights of the main frame (Items #2&3).
[] Make sure all the holes are properly aligned and screw the two
spring-loaded
locking knob assemblies (Item #8) into the back side
of the Adjustable Pulley System as shown in figure B. Tighten the locking
knobs to the Adjustable Pulley System with an adjustable wrench.
Note: Do not unwrap the two pulley assemblies
to the Adjustable Pulley System at this time.
[] Securely tighten
Components
for this step
are in Box 4
that are attached
all bolts that have been placed on the unit up to this stage.
Unit appears like this
following
this assembly
step
Step 3: SQUAT PLATFORM
& FRAME ASSEMBLY
Locate the following parts for this step:
• Large plastic squat platform (Item #5)
• Squat frame (Item #4)
• Four (4) 3/8"X4-3/4" bolts (Item #52)
• Six (6) 3/8" washers (Item #54)
• Two 3/8" lock nuts (Item #57)
[] Align the holes in the main frame (Items #2&3)
and the squat frame (Item #4) and insert the four
bolts with washers on them into the four holes as
shown in Figure C. De not tighten at this time.
Figure
C
Figure
C2
[] Slide the squat platform onto the frame assembly
by aligning the notches on the sides with the bolts
on the frame assembly. Make sure the platform goes
behind the washers.
[] Place washers and nuts on the inside of the two
forward bolts. Apply downward pressure to the
platform by kneeling on it and tighten all the bolts.
Note: The two rear bolts do not require the use
of a washer or lock nut on the inside of the
assembly.
Components
for this step
are in Box 2 and Box 4
Step 4: BOLT KEEPER
INSERTION
Locate the following parts for this step:
• Seat rail (Item #10)
• Eight (8) 3/8" X 3/4" Square Head Bolts (Item #75)
• Two (2) Rear Leg Bolt Keepers (Item #73)
• Two (2) Leg Press Bolt Keepers (Item #74)
[] Take two 3/8" x 3/4" bolts (Item #75) and place them
through holes in a Rear Leg Bolt Keeper (Item #73), Take that
assembly and slide it into a Seat Rail (Item #10) channel,
starting on the end closest to the warning label, as shown in
Figure E. Line up the end of the bolt keeper with the end of the
rail. Repeat for the other Rear Leg Bolt Keeper.
[] Go to the other end of the Seat Rail. Take two bolts (Item
#75) and place them through holes in a Leg Press Bolt Keeper
(Item #74). With the bolt-end of the bolt keeper pointed
toward the seat rail, slide that assembly into a channel as
shown in Figure El. You may need to remove the twist tie
holding the rail spacer blocks in place to slide the bolt keepers
into the rail.
Note: Please use caution when inserting bolt keepers. Edges
may be sharp.
Figure
E
Figure
Components
for this step
are in Box3
and Box4
I
I
E1
Step 5: REAR LEG
Locate the following parts for this step:
• Rear leg (Item #13)
• Seat rail (Item #10)
• Four (4) 3/8" nylon lock nuts (Item #57)
• Four (4) 3/8" washers (Item #54)
[] Find the four bolts in the channels on the bottom of the seat
rail assembly closest to the warning sticker. Place the rear leg
mounting bracket (Item #13) over the four bolts. Make sure
the edge of the bracket is flush with the end of the rail. Place
four (4) 3/8" washers (Item #54) and four (4) 3/8" nylon lock
nuts (Item #57) on the bolts as shown in figure E2 and tighten.
Figure
Components
for this
step are in Box 4
E2
Unit
appears
like
this following
this
assembly
step
Step 6: FOOT REST
Locate the following parts for this step:
• Leg press assembly (Item #11)
• Seat rail (Item #10)
• Four (4) 3/8" nylon lock nuts (Item #57)
• Four (4) 3/8" washers (Item #54)
Figure
E3
[] Find the four bolts in the channels on the bottom
of the seat rail assembly that are closest to the
threaded hole. Place the leg press assembly (Item
#11) on the four bolts. Place four (4) 3/8" washers
(Item #54) and four (4) 3/8" nylon lock nuts (Item
#57) on the bolts as shown in Figure E3. Make sure
the ends of the bolt keepers holding the leg press
bolts in place are flush with the end of the seat rail.
This will determine the final alignment of the leg
press assembly.
step are in Box
4
I Components
for this
assembly
step
Step 7: SEAT RAIL INSTALLATION
The following parts are required for this step:
• Seat Rail {Item #10)
• One (1) 3/8"X5" bolt {Item #53)
• Two (2) 3/8" washers {Item #54)
• One (1) 3/8" nylon lock nut {Item #57)
• Large Knob {Item #37)
Figure
F
[] If you have not already done so, remove
the twist-tie that holds the rail spacer blocks
and tube in place on the side of the seat rail.
[] Slide the seat rail, right side up, into the
main frame and rest it on the cross bar as
shown in Figure F.
[] Slide the 3/8"X5" bolt {Item #53) with a
washer through main frame and seat rail as
shown in Figure F. Place 3/8" washer {Item
#54) and 3/8" nylon lock nut
(Item #57) on bolt and tighten.
[] Place the large knob (Item #37) into the
hole in the top of the frame and tighten.
Step 8: SEAT INSTALLATION
Locate the following
• Seat Assembly
parts for this step:
[] Pull out and lock the pin on the left side of the seat
assembly and slide the seat onto the rail as shown in
Figure G.
Figure
Unit appears
like this
Components for this
step are in Box 3
I
I
following
this
assembly
step
G
Step 9: RAIL END CAP INSTALLATION
Locate the following parts for this step:
• Rail End Cap (Item #58)
• Two (2) #10X3/4" self tapping screw (Item #44)
[] Place the end cap (Item #58) on the end of the rail with arrow
inside end cap facing up.
®
[] Secure the end cap to the end of the rail using two (2)
#10X3/4" self tapping screws (Item #44) shown in Figure H.
step are in Box
4
i Components
for this
If your unit came with a lat attachment,
skip now
to lat instructions:
Step 1 Page 14.
I
I
Unit
appears
like
this following
this
assembly
step
Step 10: INCLINE
BENCH REST INSTALLATION
Locate the following parts for this step:
• Incline bench rest (Item #21)
• Incline bench rest back (Item #22)
• Three (3) 3/8"X2" bolts (Item #48)
• Three (3) 3/8" washers (Item #54)
• Two (2) #10X3/4" self tapping screws
(Item #44)
optional
i i
[] Match up the oval bosses on the
incline seat rest (Item #21) with the oval
cutouts in the lower lat tower (Item #t)
as shown in Figure K.
[] Place the incline bench rest back (Item
#22) on the rear of the lower lat tower
(Item #1) and match up the three holes
for the 3/8" bolts as shown in Figure K.
Note: Make sure the textured, nonmachined side of the incline rest back
faces outward away from the machine,
[] Slide the three (3) 3/8"X2" bolts (Item #48) into
the three holes in the incline bench rest back (Item
#22) through the lower lat tower (Item #1) and into
the incline seat rest (Item #21) as shown in Figure
K. Securely tighten these three bolts.
[] Screw the two (2) #10X3/4" (Item #44) screws
into the incline bench rest back (Item #22) as
shown in Figure K.
Figure
K
Components
for this I
step are in Box 4
I
lat tower
Step 11: ROD BOX INSTALLATION
Locate the following parts for this step:
• Rod box with Power Rods {Item #23)
• Rod box frame {Item #24)
• Three (3) #10Xl" self tapping screw
(Item #45)
• Three (3) 1/4" washers (Item #55)
[] Slide rod box with Power Rods (Item
#23) into rod box frame (Item #24) as
shown in Figure L.
[] Tighten three (3) #10Xl" screws {Item
#45) with three (3) 1/4" washers {Item
#55) through the slot in rod box frame
(Item #24) and into the screw bosses in
the bottom of the rod box with Power
Rods {Item #23) as shown in Figure L.
Figure
L
Unit appears
this following
assembly
Components for this
step are in
Box 1 & Box 4
I
I
Step 12: ROD BOX FRAME
Locate the
• Rod Box
• Three (3)
• Three (3)
INSTALLATION
following parts for this step:
with Power Rods with frame {Items #23 & 24)
3/8"X3/4" bolts {Item #46)
3/8" washers {Item #54)
[] Start two (2) 3/8"X3/4" bolts {Item #46) with 3/8" washers {Item
#54) into the lower two holes in the rear of the lower lat tower
{Item #1) as shown in Figure M.
[] Slide the rod box frame (Assembly #24) onto the two bolts
making sure the rod box frame is behind the washers as shown in
Figure M.
[] Thread the third 3/8"X3/4" bolt {Item #46) into the top hole of
the rod box frame (Item #24). Securely tighten all bolts.
CAUTION:
When hooking up the Power Rods, do
not stand directly over the tops of the
rods. Stand off to the side while
connecting and disconnecting
the
Power Rods from the cables.
Unit appears
like
this following
this
assembly
step
(shown
with
optional
tower)
lat
Figure
M
step
like
this
Step 13: LOWER
LAT CROWN INSTALLATION
Locate the following parts for this step:
• Lower lat crown (Item #76)
[] Press Lower Lat Tower Crown (Item #76) into open end of lower
lat tubing to finish off. Bottom surface of lower lat crown should be
in contact with incline bench rest.
Note: if you have attached
discard this piece.
Components for this
step are in
Box 4
a lat tower, skip this step and
I
I
Figure
Step 14: BENCH
REST BRACKET
N
INSTALLATION
Locate the following parts for this step:
• Bench (Item #25)
• Bench rest bracket (Item #26)
• Three (3) 1/4"X1-1/2" phillips head screws (Item #41)
• Three (3) 1/4" Washers (Item #55)
[] Assemble the bench rest bracket (Item #26) to the back of the
bench (Item #25) using three (3) 1/4"X1-1/2" phillips head screws
(Item #41) and three (3) 1/4" washers (Item #55) as shown in
Figure N.
Note: Double check to make sure bench is stable in the
incline position and the foot rest assembly
is properly
positioned when the bench is in the flat position, in the flat
position, the bench should NOT rest on the foot rest.
Figure
Components for this
step are in
Box 3 & Box 4
I
I
0
The Lat Assembly is an optional attachment which,
depending on the machine you ordered, may or may
not be part of your Bowflex.
Lat Assembly
Lat Assembly
Parts List
Item No.
Qty.
Part No.
17
1
10033
Description
UPPER LAT CROSS BAR W/PULLEYS
19
1
10031
UPPER LAT TOWER
20
1
10032
STRAP HOOK
46
6
10103
BOLT, 3/8" X 3/4"
31
2
10038
LAT CABLE
50
2
10109
BOLT, 3/8" X 2-3/4"
33
2
50334
SNAP HOOK
54
10
90138
WASHER,
34
1
10037
50" BENT BAR
57
2
90196
NUT, 38", NYLON
Item
#: 17
Qty.:
Part
Item
1
#: 10033
Descr:
Upper
Cross
Lat
Bar w/
#: 19
Item
Qty.:
Part #: 10031
Part
Descr:
Descr:
Upper
Lat
Description
10163
SCREW,
Item
2
#: 31
1
Qty.:
#: 10032
Part
Tower
pulleys
Part No.
40
1/4" x 5/8"
PHILLIPS
#: 20
oty.: 1
Item No. Qty.
Strap
Hook
2
#: 10038
Descr:
Lat
Cable
Length:
HEAD
3/8"
Item
#: 33
Item
Qty.:
2
Qty.:
Part
#: 50334
Descr:
Snap
MACHINE
LOCK
#: 34
1
Part #: 10037
Hook
Descr:
50" Bent
Bar
56.25"
Item #: 57
#: 40
Item
Item
Item
#: 46
Qty.:
Qty.:
8
Part
#: 10103
#: 10109
Descr:
Descr:
3/8"X2-3/4"
Bolt
3/8"
Bolt
Qty.:
2
Item
2
Part
Part
Qty.:
#: 50
X 3/4"
Part
#: 54
#: 10163
Descr:
1/4"X5/8"
Phillips Head
Machine
Screw
2
#: 90196
Descr:
Qty.:
10
Part
#: 90138
Descr:
3/8"
3/8"
Nylon
Nut
Washer
Lock
Step 1: LAT TOWER
ASSEMBLY
Locate the following parts for this step:
• Lat cross bar w/pulleys
(Item #17)
• Upper lat tower (Item #19)
• Two (2) 3/8"X2-3/4"
bolts (Item #50)
• Four (4) 3/8" washers (Item #54)
• Two (2) 3/8" nylon lock nuts (Item #51)
• Strap hook (Item #20)
• Two (2) 1/4"X5/8" phillips head screws (Item #40)
[] Attach the lat cross bar assembly (Item #17) to the upper lat
tower (Item #19) with two (2) 3/8"X2-3/4" bolts (Item #50), four
(4) 3/8"washers
(Item #54) and two (2) 3/8" nylon lock nuts
(Item #57) as shown in Figure I.
Strap
Hook
_
[] Attach the strap hook (Item #20) to the rear of the upper lat
tower using two (2) 1/4"X5/8" phillips head screws (Item #40)
also shown in Figure I. Make sure the strap hook loop faces
downward as shown in the inset.
Note: Take care to securely
upper lat tower.
tighten
Components
for this step are in
the Lat Attachment
Box
Step 2: LAT TOWER
Figure
the lat cross bar to the
Unit appears
like this
I
following
assembly
I
this
step
INSTALLATION
Note: It is recommended
that two
people be used to accomplish
this
step. Take care to insure the
upper lat assembly
is properly and
securely attached
to the base
assembly.
Figure
Locate the following parts for this
step:
• Six (6) 3/8"X3/4" bolts (Item #46)
• Six (6) 3/8" washers (Item #54)
• Upper lat tower assembly (from
Step 9)
go to Step 10 on Page 11
to finish assembly.
Plug
Unit
appears
like
this
foflowing
this
assembly
q_
*Remove and discard the foam plug
from the lat tower cable storage hole.
J
"Foam
[] Assemble the upper lat tower
assembly to the base unit using six (6)
3/8"X3/4" bolts (Item #46) and six (6)
3/8" washers (Item #54) as shown in
Figure J.
Please
I
step
The Leg Assembly is an optional attachment which,
depending on the machine you ordered, may or may not
be part of your Bowflex.
Leg Assembly
Leg Assembly
Parts List
55
4
90153
1/4" WASHER
70
2
90189
PIVOT BUSHING
61
1
10053
LEG EXTENSION
SEAT ASSEMBLY
71
2
10170
HEX HEAD BOLT, 1/4" X 2-3/4"
62
1
10051
LEG EXTENSION
MAIN
72
2
90204
NUT, 1/4" NYLON
63
1
10052
LEG EXTENSION
FOOT TUBE
64
1
10054
LEG EXTENSION
PIVOT TUBE
65
6
50304
FOAM ROLLER
66
3
95206A
3/4"X15
67
2
10056
LEG EXTENSION
68
2
90161
1" SMALL
69
6
90218
3/4"
Item
#: 61
Qty.:
Part
Item
1
#: 10053
Descr:
Part
Leg Extension
Seat Assembly
1
Part
Item
Qty.:
#: 10056
Length:
Item
#: 63
Part
Part
Descr:
Leg Ext.
Cable
Item
#: 64
Item
1
Qty.:
1
Qty.:
#: 10052
Part
#: 10054
Part
Descr:
2
Descr:
STAR KNOB
Leg Extension
Foot Tube
Leg Ext.
Main Fra
#: 67
Qty.:
TUBE
CABLE
Qty.:
#: 10051
Descr:
Item
CHROME
LOCK
END CAP
#: 62
Qty.:
3/4"
FRAME
Descr:
Leg Extension
Pivot Tube
Descr:
#: 65
Item
6
#: 66
Qty.:
#: 50304
Part
Leg Extension
Roller
3
#: 95206A
Descr:
Leg Extension
Chrome Tube
J
#: 68
2
#: 90161
1" Smafl
Item
#: 69
Qty.:
Part
Item #: 70
6
Qty.:
#: 90218
Descr:
3/4"
2
Part #: 90189
End Cap
Descr:
Pivot Rushing
Knob
73.50"
©
Item
#: 51
Qty.:
Part
Item
3
Qty.:
#: 90139
Descr:
3/8"
Bolt
#: 71
Part
X 3"
Item
Item
Qty.:
Item #: 54
Part
Qty.:
Descr:
6
2
#: 10170
Descr:
1/4"X2-3/4"
3/8"
Washer
Bolt
Item
Qty.:
Part
Descr:
#: 55
4
#: 90156
1/4"
Washer
Qty.:
Part
3
Descr:
#: 90196
#: 72
2
#: 90204
1/4"
Nylon
Nut
3/8"
Nylon
Nut
Part #: 90138
Descr:
#: 57
Lock
Lock
Step 1 : LEG EXTENSION
FOOT TUBE INSTALLATION
Locate the following parts:
• Leg extension main frame (Item #62)
• Leg extension foot tube (Item #63)
• Two (2) 3/8"X3" bolt (Item #51)
• Two (2) 3/8" nylon lock nuts (Item #57)
• Four (4) 3/8" washers (Item #54)
Figure
P
[] Insert the leg extension foot tube (Item #63) into the
leg extension main frame (Item #62) saddle bracket,
aligning the holes in the bracket with the holes in the foot
tube, as shown in Figure P.
[] Insert two 3/8"X3" bolts (Item #51) with 3/8" washers
(Item #54) through the holes in both tubes as shown in
Figure P.
[] Install 3/8" washers (Item #54) and then 3/8" nylon
lock nuts (Item #57) onto the bolts and securely tighten.
Components
for this step
are in the Leg Extens on Box
Unit appears
this following
assembly
Step 2: LEG ASSEMBLY
EXTENSION
like
this
step
TUBE
Locate the following parts
• Leg extension main frame (Item #62)
• Leg extension pivot tube (Item #64)
• 3/8"X3" bolt (Item #51)
• 3/8" nylon lock nut (Item #57)
• Two (2) 3/8" washers (Item #54)
%
[] Untwist the twist-tie that is holding the
bushings in place in the leg extension pivot tube
(Item #64).
[] Place the leg extension tube (Item #64) as
shown in Figure Q. The tube is symmetrical so
orientation does not matter.
[] Insert the 3/8"X3" bolt (Item #51) with a 3/8"
washer (Item #54) on it through the leg
extension main frame (Item #62) and through
the leg extension tube (Item #64) as shown in
Figure Q.
[] Install a 3/8" washer (Item #54) onto the bolt
and securely tighten the 3/8" nylon lock nut
(Item #57).
Components
for this step
are in the Leg Extens on Box
Figure
Q
Unit
appears
like
Step 3: LEG EXTENSION
SEAT INSTALLATION
__
Locate the following parts:
• Leg extension assembly (from previous step)
• Leg extension seat assembly {Item #61)
• Two (2) 1/4"X2-3/4"
bolt {Item #71)
• Two (2) 1/4" nylon lock nuts {Item #72)
• Four (4) 1/4" washers {Item #55)
_Hinges
#
[] Place the leg extension seat {Item #61) on top of
the horizontal tube on the leg extension assembly
{Item #62) with the hinge brackets facing the direction
shown in Figure R.
[] Insert two 1/4"X2-3/4" bolts {Item #71) with 1/4"
washers {Item #55) through the brackets on the
bottom of the leg extension seat {Item #61).
Figure
R
Unit appears
this following
[] Install 1/4" washers {Item #55) onto the bolts and
securely tighten 1/4" nylon lock nuts {Item #72) on the
bolts.
Components
assembly
for this step
are in the Leg Extens on Box
Step 4: INSTALLING THE LEG EXTENSION
CHROME TUBES AND FOAM ROLLERS
Locate the following parts
• Portion of leg extension attachment already
assembled
• Three (3) leg extension chrome tubes {Item #66)
• Six (6) leg extension rollers {Item #65)
• Six (6) leg extension tube end caps {Item #69)
• Two (2) 73.50" leg extension cables {Item #67)
Components
for this
step are in Leg
Extension Box
Figure
S
®
[] Back out the screws that are in the end holes of the
leg extension pivot tube {Item #64) just enough to
slide the chrome tube through the holes.
[] Slide Chrome tubes into all three holes as shown in
Figure S.
[] Slide the LARGE LOOP of the leg extension cables
(Item #67) onto the lowest chrome tube, one on each
side of the leg extension pivot tube.
[] Slide the foam rollers (Item #65) onto the
chrome tubes (Item #66) as shown in Figure T.
[] Push the roller end caps (Item #69) into the
ends of the chrome tubes (Item #66) as shown
in Figure T.
_
Unit
assembly
this
Note: You may need to use a rubber mallet
to get the end caps securely into the
chrome tubes.
appears
like
step
following
this
Figure
T
step
like
this
Step 5: INSTALLING
THE LEG EXTENSION
ATTACHMENT
Unit
appears
like
this following
this
assembly
step
[] Place the leg extension on the end of the rail and tighten
the two small star knobs (Item #68) through the sides of
the leg extension rail bracket and into the rail as shown in
Figure U.
(shown
with
optional/at
tower)
[] Take the leg attachment cables and snap them into the
cable storage clips on the bracket under the seat rail.
!
Figure
U
BEFORE EACH USE OF THE EQUIPMENT,
CHECK ALL FASTENERS, SNAP HOOKS,
CABLES AND PULLEY FUNCTIONS.
TIGHTEN AND FASTEN AS NEEDED.
CHECK PULLEYS AND CABLES FOR
WEAR AND FUNCTION.
ASSEMBLING YOUR BOWFLEX T-BAR
Your T-bar was shipped fully assembled with the metal bar
resting in the loops of the nylon strap. If, however, the bar and
the nylon strap separated during shipping, follow these
instructions for reassembly.
[] The nylon strap has one flat side and one side with several
twists. Lay the nylon strap on a flat surface with the flat
side down, as shown in Figure V.
Figure
V
Figure
W
Figure
X
Figure
Y
Lift the strap by the metal rings and hold it in front of you.
Turn the strap completely over with the twisted side down.
Grab the strap in the center with the index finger of one
hand. See Figure W.
[] Use your index finger and thumb of your free hand to
spread the strap into two loops, as shown in Figure X
[] Using your free hand, slide the bar through the loops.
Remove your fingers from the loop. The strap should wrap
around the bar evenly and slide loosely and freely around
the bar. See figure Y.
Expanding your Bowflex
Ultimate from 310 pounds
to 410 pounds
Step 1: Simply slide
the new rods into the
back of the Ultimate's
rod pack. Make sure
the new Power Rods
are secure and fully
seated into the base
before
using
them.
POWER ROD _ UPGRADE
FOR ONLY$99
1-800.269-3539
t
Please
fold over and tape
before
mailing
Please
fold
before
mailing
over
and
tape
!
Place
Stamp
Here
The Nautilus Group, Inc.
1400 N.E. 136th Ave.
Vancouver, WA 98684
Information
about your Bowflex Ultimate
(Keep for your records)
What
Warranty
Is Covered
The Nautilus Group, Inc. warrants
to the original purchaser
of the Bowflex _ home fitness machine to be free from defects in
materials or workmanship,
with the exceptions
stated below. This warranty
is not transferable
or applicable to any person other
than the original purchaser.
Bowflex
The Bowflex patented
Power
original purchaser
for seven
Ultimate. The warranty
does
must completely
fill out the
98684 within thirty (30) days
Ultimate
Rod: resistance is covered by a No-Time-Limit
Warrant)a
The Bowflex Ultimate is warrantied
to the
(7) years. This seven year warranty
covers all defects in material or workmanship
of the Bowflex
not cover commercial
use or misuse & abuse by the consumer.
To make this warranty
effective, you
owner registration
card and return it to The Nautilus Group, Inc., 1400 NE 136th Ave. Vancouver,
WA
of your purchase of the Bowflex.
Warranties
Do Not Cover
• A Bowflex pun'hased
for commercial
or institutional
use.
• Damage due to use by persons who weigh more than 300 pounds.
• Damage due to abuse, misuse, accident or acts of God (such as floods).
• Consequential
or incidental
damages.
Some states do not allow the exclusion or limitation
of incidental or consequential
may not apply to you.
damages,
so the above
limitation
or exclusion
What We Will Do
The Nautilus
possible,
Group,
The Nautilus
Inc. will repair
Group,
any Bowflex
Inc. at its option,
that proves
will either
to be a defect in materials
replace
How
your
Bowflex
or workmanship.
or refund
your purchase
In the event repair
is not
price.
To Get Service
Simply return the defective part at your expense to The Nautilus Group, Inc., 1400 NE 136th Ave. Vancouver,
WA 98684. Include
explanation
of the problem. For information,
you may contact a service representative
at 1-800-269-3539
or write us at the above
address, Attention
Warrant)a
Adequate
protective packaging
of the defective parts or unit and cost of shipping to the above
address
are your
This warranty
responsibilit)a
The repaired
part or unit will be returned
to you at the company's
gives you specific
legal rights,
How State Law Applies
and you may also have other rights
which vary
expense.
from state to state.
an
BOWFLEX
6 WEEK SATISFACTION
GUARANTEE
We want you to know that Bowflex is a superior product. Your satisfaction is guaranteed. If for
some reason you are not 100% satisfied with your Bowflex, please follow the instructions below
in order to return your merchandise and receive a refund of the purchase price, less shipping
and handling.
Call our Customer Service Department at (800) 607-3539 for a Return Authorization
Number. Return authorization will be granted if:
1) You purchased your Bowflex Machine directly from The Nautilus Group, Inc.
2) If you are calling within 6 weeks of delivery date of merchandise. Returns should be
shipped to The Nautilus Group, Inc., 1400 N.E. 136th Ave., Vancouver, WA 98684.
All returned merchandise must be properly packaged in the original boxes and in good
condition. Please note: You are responsible for return shipping and any damage or
loss to merchandise which occurs during return shipment to The Nautilus Group, Inc,
We highly recommend that insure your shipment.
3.
Please mark all boxes clearly with:
Return Authorization Number
Name
Address
Phone Number
Boxes without this information clearly marked on the outside may be refused.
4.
Please make copies of your original invoice and put one in each box of merchandise.
Merchandise must be received by The Nautilus Group, Inc. within two weeks of the date you
were issued your Return Authorization Number.
Refunds
may be denied
or delayed
if these are not completely
followed.
This Bowflex Satisfaction Guarantee applies only to merchandise purchased by consumers, directly
from The Nautilus Group, Inc. This guarantee does not apply to sales made by dealers or distributors.
The Nautilus Group, Inc.
1400 N.E. 136th Ave. Vancouver, WA 98684
Bowflex
PN 10204AA
(0503)
and the Bowflex Logo
istered trademarks
© 2003 The Nautilus Group, tnc.
of Nautilus, Inc., a NYSEqisted
WA98684
company
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.2 Linearized : No Page Count : 23 Page Layout : SinglePage Page Mode : UseNone Producer : Goby Monitor Application version 3, 2, 1, 4 Create Date : Thu Apr 05 01:44:59 2007 Author : Title : Subject :EXIF Metadata provided by EXIF.tools