BRK FAL-TEM Wireless Temperature Sensor User Manual OLTEMP

BRK Brands Inc Wireless Temperature Sensor OLTEMP

M7U-FAL-TEM_User Manual

INTRODUCTIONCongratulations on your purchase of the ONELINK WirelessTemperature Sensor. This device senses temperaturechanges ranging between 14˚F to 112˚F (-10˚C to 44˚C). This Quick Start Guide describes how to set up and troubleshoot your Temperature Sensor.For a full system set-up manual, please visit our website: www.onelinkhome.comCONTROLLING YOUR SENSORUsing your computer and the Wireless Gateway, you locally manage yourhome environment with the ONELINK Wireless System. When configured, thesystem can notify you of any new events by sending an e-mail when your Temperature Sensor detects an event (atemperature change) that moves beyond the user specified limits.How It WorksThe Sensor monitors ambient temperature and if the temperature movesbeyond your set temperature range, it sends an event to your WirelessSystem Gateway. When the External Temperature Probe is connected to the Temperature Sensor, the internal sensor element is disabled.INSTALLATION OVERVIEWYour package contains the following:Installing your sensor is a simple process.1. Locate the antenna and screw it into the top-left corner of the sensor untilit is secure. Sharp objects should be stored out of reach of children toprevent injury.2. Insert batteries. On the top of the sensor, slide open the door and inserttwo AAA alkaline batteries. The inside of the sensor indicates the polarity(+ and -) of the batteries. Close the door after inserting batteries.The sensor does not support rechargeable NiCad or NiMH batteries.3. Mount the sensor.Installing Your Wireless Temperature SensorYour sensor can either be mounted on a wall or just sit on a horizontal surface.Wall Mount Your Wireless Temperature SensorWarning: When mounting near a window, drilling too close to the glasscould break the glass and possibly cause it to shatter and cause injury.The window extends deeper into the frame than can be seen; therefore,ensure your screw is beyond the glass before drilling. Thoroughly cleanand dry the surface.1. You can mount the sensor securely using the screwsin the hardware kit. Using the holes on the drillingtemplate found later in this guide, mark the positionof the holes to be drilled. For drywall or other composite surfaces use a 7/32” drill bit. Drill a holefor each of the mounting screws and insert a plasticwall anchor into each hole. For other solid surfaces, use a 1/16” drill bit. Drill a pilot hole for each of the mounting screws.2. Ensure that fresh batteries have been installed.3. Mount the sensor onto the screws and slide up to lock into place.Attaching the Temperature ProbeThe probe, which attaches to the Temperature Sensor, is immersible anddesigned to monitor the temperature of air or water. A pool, aquarium, deep freezer, or baseboard radiator are just a few suggested places to monitor ambient air or water temperature.1. Insert the plug into the bottom of the sensor.2. Place the Temperature Probe in the locationyou wish to monitor.Wall Mount Drilling TemplateMounting tools: Screwdriver, electric drill or awl. On hard surfaces, it is recommended that you pre-drill 1/2-inch deep pilot holes with a drill bitslightly smaller than the bracket mounting screws before securing the bracketto the surface. When mounting a sensor on soft surfaces like sheetrock, usean awl to punch holes in the material slightly smaller than the plastic anchorsincluded in the hardware mounting kit.The illustration is drawn to a one-to-one scale, which means that it provides the exact dimensions required to mount the unit.AAAAAATemperature SensorHardwareMounting KitTemperature Sensor ProbeBatteriesAntennaFeature Locator1.6 mm (1/16 inch)maximum 1QUICK START GUIDETemperature SensorM08-0234-002 07/12Installation HintsPlease consider the following points when mounting the sensor:• The ONELINK Temperature Sensor is constructed for indoor use.• Typically, the sensor’s range is 65-200 feet from the Gateway, dependingon the number of obstacles. These can include metal framing, thick walls,and other wireless devices. It is recommended that different positions betried for optimal results.Features and Specifications• Attaches to any flat non-metal surface• Operates on 2-AAA Alkaline batteries• LED indicator when sensor is triggeredFrequency range: 915 MHzTypical open air range (line of sight): 200 ft (60 m)Typical indoor range: 65 feet (20 m)Sensor size: 1.613” x .615” x 3.441”Operational temperature:14˚ to 112˚ F with all components operating within manufacturer thermal limitsBattery compartment To pDrill holes inthese positions2.0 in
TROUBLESHOOTINGProblemLED does not light upSolution• Ensure the batteries are properly inserted with the correct polarity.• Ensure you are using fully charged AAA batteries.ProblemWireless System Gateway does not recognize the sensor during setupSolution• Ensure sensor is powered. Position the sensor in closer proximity to your Wireless System Gateway and try again. Ensure there are no otherwireless devices interfering with the sensor. The sensor transmits on the915 MHz frequency.ProblemEvents are not triggeredSolution• Is the sensor registered with your Wireless Gateway?• Ensure that you have the proper settings configured for the sensorProblemSensor continually sends an eventSolution• Ensure that you have the proper settings configured for the sensor. For example, you have armed the sensor.• The sensor can be configured so that it can send an event when the contacts are closed or when they are opened.FAQHow far away can the sensor be placed from my Wireless SystemGateway?Typically 65 feet (20 meters).Can I place the sensor in a different room than my Wireless SystemGateway?Yes, the sensor and Wireless System Gateway use radio frequencies tocommunicate with each other. These frequencies can go through objects like walls, ceilings and floors.How long will the battery last?The battery is expected to last up to 12 months. This depends on actual useand how often the sensor is triggered. Do not use rechargeable batteries.The light on the sensor is not on?This indicates that the sensor has gone into hibernation mode. It wakes upwhen the sensor is triggered.REGULATORY INFORMATIONFCC Notices:NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmfulinterference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used inaccordance with the instructions, may cause harmful interference to radiocommunications. However, there is no guarantee that interference will not occur in a particularinstallation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment offand on, the user is encouraged to try to correct the interference by one ormore of the following measures:• Reorient or relocate the receiving antenna.• Increase the separation between the equipment and receiver.• Connect the equipment into an outlet on a circuit different from that towhich the receiver is connected.• Consult the dealer or an experienced radio/TV technician for help.Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority tooperate the equipment.This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received,including interference that may cause undesired operation.Model: OLTEMPICES-003 StatementThis Class B digital apparatus complies with Canadian ICES-003.This device complies with Industry Canada licence-exempt RSS standard(s).Operation is subject to the following two conditions: (1) this device may notcause interference, and (2) this device must accept any interference, includinginterference that may cause undesired operation of the device.Cet appareil numérique de la classe B est conforme à la norme NMB-003 duCanada.Le présent appareil est conforme aux CNR d’Industrie Canada applicablesaux appareils radio exempts de licence. L’exploitation est autorisée aux deuxconditions suivantes: (1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi,même si le brouillage est susceptible d’en compromettre le fonctionnement.Model: OLTEMPA © 2012 BRK Brands, Inc. All rights reserved.Distributed by BRK Brands, Inc.3901 Liberty Street Road, Aurora, IL 60504-8122ONELINK®is a registered trademark of BRK Brands, Inc.First Alert®is a registered trademark of the First Alert Trust used under license.LIMITED WARRANTYONELINK Wireless Temperature SensorBRK Brands, Inc., ("BRK") the maker of First Alert®brand products warrantsthat for a period of one year from the date of purchase, this product will befree from defects in material and workmanship. BRK, at its option, will repairor replace this product or any component of the product found to be defective during the warranty period. Replacement will be made with a new or remanufactured product or component. If the product is no longeravailable, replacement may be made with a similar product of equal or greatervalue. This is your exclusive warranty.This warranty is valid for the original retail purchaser from the date of initialretail purchase and is not transferable. Keep the original sales receipt. Proof of purchase is required to obtain warranty performance. BRK dealers,service centers, or retail stores selling BRK products do not have the right to alter, modify or any way change the terms and conditions of thiswarranty.This warranty does not cover normal wear of parts or damage resulting from any of the following: negligent use or misuse of the product, use onimproper voltage or current, use contrary to the operating instructions, disassembly, repair or alteration by anyone other than BRK or an authorizedservice center. Further, the warranty does not cover Acts of God, such asfire, flood, hurricanes and tornadoes or any batteries that are included withthis unit.BRK shall not be liable for any incidental or consequential damages causedby the breach of any express or implied warranty. Except to the extent prohibited by applicable law, any implied warranty of merchantability or fitness for a particular purpose is limited in duration to the duration of theabove warranty. Some states, provinces or jurisdictions do not allow theexclusion or limitation of incidental or consequential damages or limitationson how long an implied warranty lasts, so the above limitations or exclusionmay not apply to you. This warranty gives you specific legal rights, and youmay also have other rights that vary from state to state or province toprovince.How to Obtain Warranty ServiceFor customer service, technical support, and warranty claims, contact ourCustomer Support Center at 1-800-323-9005 Monday - Friday 7:30 am to5:00 pm Central Standard Time.Battery LifeFor your ONELINK wireless devices that require batteries, use high-quality, non-corrosive batteries designed for use in electronic equipment. Battery lifeis up to one year with normal usage. Do not use rechargeable batteries inany ONELINK device.RegistrationRegister your product at:www.onelinkhome.com2Battery Regulations:• Always use the exact batteries specified by this User’s Manual. DO NOT use rechargeable batteries. For products requiring multiplebatteries, replace all batteries of a set at the same time. Do Not MixOld and New Batteries. Clean the battery contacts and also those ofthe device prior to battery installation. Install batteries correctly withregard to polarity (+ and -).• Keep battery out of reach of children. In the event a battery is swallowed, immediately contact your poison control center, yourphysician, or the National Battery Ingestion hotline at 202-625-3333as serious injury may occur. Please dispose of or recycle used batteries properly, following any local regulations. Consult your local waste management authority or recycling organization to find an electronics recycling facility in your area. DO NOT DISPOSEOF BATTERIES IN FIRE. BATTERIES MAY EXPLODE OR LEAK.

Navigation menu