BRYANT Furnace/Heater, Gas Manual L1001009
User Manual: BRYANT BRYANT Furnace/Heater, Gas Manual BRYANT Furnace/Heater, Gas Owner's Manual, BRYANT Furnace/Heater, Gas installation guides
Open the PDF directly: View PDF 
.
Page Count: 2
| Download | |
| Open PDF In Browser | View PDF |
Installation Instructions NOTE: Read installation. the entire SAFETY instruction manual before starting the CONSIDERATIONS CUT Improper maintenance, installation, adjustment, or use can cause explosion, other conditions property damage. which may cause Consult a qualified alteration, fire, electrical death, personal installer, service service, shock, or injury, agency, or or your distributor or branch for information or assistance. The qualified installer or agency must use factory-authorized kits or accessories when modifying this product. Refer to the individual instructions Follow packaged all safety with the kits or accessories codes. Wear safety glasses, codes, the current editions Code (NFGC) NFPA 54/ANSI Electrical Code (NEC) NFPA 70. and Fuel the refer to the current of Canada Installation CAN/CSA-BI49.1 and .2 Natural Gas and Propane Codes, and Canadian Electrical Code CSA C22.1 Recognize safety information. you manuals, this symbol CAUTION. DANGER the signal of the National This is the safety-alert on be alert to the potential Understand severe see words the unit Standards symbol/_. and in instructions for personal DANGER, injury or death. Sheet metal parts may have sharp edges or burrs. Use care and wear appropriate protective clothing, safety glasses and gloves when handling parts and servicing furnaces. FIRE, EXPLOSION, HAZARD Failure personal WARNING, WARNING signifies personal injury or product and property damage. to highlight suggestions which will result installation, reliability, or operation. ELECTRICAL Failure to follow this warning death and/or property damage. could SHOCK The ability to properly perform service on this requires certain expertise, mechanical skills, equipment. If you do not possess these, do not perform any service on this equipment other procedures recommended in the User's Manual. in possible equipment tools, and attempt to than those or and hazards NOTE is used in enhanced SHOCK result in personal Before installing or servicing unit, always turn electrical and gas to unit and tag with appropriate There may be more than one disconnect ELECTRICAL to follow this warning could result iniury, death and / or property damage. Table 1 -Models Kit Part Used with Models KGAHA6101PSW 58HDV040 359BAY036040 KGAHA6201PSW 58HDV060 359BAY036060 58HDX060 359AAV036060 PG9YAB036060 KGAHA6301PSW 58HDV080 359BAY060080 58HDX080 359AAV036080 PG9YAB036080 359AAV048080 PG9YAB048080 KGAHA6401PSW 58H DVl O0 359BAY0601 O0 58H DXl O0 359AAV060100 PG9YAB060100 which could result in personal injury or death. CAUTION is used to identify unsafe practices which may result in minor FIRE, EXPLOSION, HAZARD iniury. injury. These words are used with the safety-alert symbol. identifies the most serious hazards which will result in personal may result in personal Gas National In Canada, When editions this caution clothing, of the National Z223.1 to follow when installing. protective and work gloves. Have a fire extinguisher available. Read these instructions thoroughly and follow all warnings or cautions include in literature and attached to the unit. Consult local building HAZARD Failure switch. injury, off main lockout. INTRODUCTION This instruction switch shown covers DESCRIPTION the installation of high-altitude pressure kits in condensing furnaces. The switch set points on the label attached to the front of the switch. KIT The high-altitude items: High altitude Installation switch high-altitude ft. (1219 kit contains the pressure kit is required for the M) above sea level. following 1 assembly instructions 1 INSTALLATION OF PRESSURE SWITCH TO BLOWER /INDUCER ASSEMBLY 1. Mark switch USAGE installation of the condensing furnaces when installed with a Category IV vent system at altitudes equal to or higher than 4000 CONTENTS pressure switch This are AND two (2) wires connected switch and the two (2) wires switch. to the high-fire connected pressure to the transition TO TRANSITION BOX / COLLECTOR BOX 2. Disconnect the four (4) wires from the pressure switches, 3. Mark and disconnect switches. the pressure tubes from the pressure MOUNTING BRACKET 4. Remove the two bracket 5. Install (2) screws from the front mounting (See Fig. 1). new high bracket altitude pressure switches and mounting with two (2) screws. 6. Reconnect switches. the pressure tubes to the high altitude pressure Aog37g Fig. 1 - Pressure 7. Reconnect wiring wires to the switches 2009 CAC / BDP • Manufacturer reserve8 in the furnace diagram. 8. Check furnace for proper stallation Instructions). Copyright as shown Switch 7310 W. Morris St. • the right to change, operation Indianapolis, at any time, (refer to furnace IN 46231 specification8 In- Printed and design8 without in U.S.A. notice Edition and without 2 obligations. Date: 06/09 Catalo_l Replaces: No: IIK-KGAHAO101-02 IIK KGAHA6101 01
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.2 Linearized : No Page Count : 2 Page Layout : SinglePage Page Mode : UseNone Producer : Goby Monitor Application version 4, 0, 0, 13 Create Date : Fri Feb 12 04:13:08 2010 Author : Title : Subject :EXIF Metadata provided by EXIF.tools