BTC Korea Co 190M LCD Monitor User Manual 190M
BTC Korea Co Ltd LCD Monitor 190M
Users Manual
190M LCD Monitor
User Manual
This equipment has been designed for the normal use. It is certified to comply with
Electron Wave Suitable Registration. The user this equipment in everywhere
including residential areas.
Notice
This equipment is one of first class quality. The LCD panel is composed of about 4
Million pixels and may have some faulty pixels. LCD panels with a maximum of 10
faulty pixels are classified as products of good quality. This standard is accepted by
other manufacturers of LCD panels. An LCD panel without any faulty pixels is too
expensive for the average customer. Our ”A” class panels have the least 5 faulty
pixels. We guarantee that our panels will provide the user with high quality
performance. Therefore, no product exchanges or refunds will be made in regards to
this matter.
190M LCD Monitor
IMPORTANT
SAFEGUARDS
IMPORTANT SAFEGUARDS
Always be careful when using your LCD Monitor. To reduce the risk of fire, electrical shock, and other
injuries, keep these safety precautions in mind when installing, using, and maintaining your machine.
Do not open the monitor. Contact your dealer if the monitor is not operating
properly.
Do not place the monitor in direct sunlight or close to any heat source. -
Product malfunction or fire hazard may occur.
Do not drop metal objects like coins or hairpins into the monitor. -Electrical
shock or fire hazard may result.
Provide a secure connection to the power supply and do not use damaged
power cords or plugs. -Electrical shock or fire hazard may result.
Do not place the monitor in exposed places or near water.
Do not clean the monitor with water or touch it with wet hands. -Electrical
shock or fire hazard may result.
During lightening storms, unplug the monitor from the wall outlet and do not
touch it. -Electrical shock or fire hazard may result
Not using the monitor for hours, unplug the monitor from the wall outlet. -
Dust may cause heat, fire, shock or short circuit
IMPORTANT SAFEGUARDS
In case of any smoke or abnormal noise, immediately stop use of product and
pull the power cord from the wall outlet. Then call your local dealer or service
representative for assistance. -Any subsequent use may result in fire or
electric shock.
Install the monitor at the specified position from the wall to be well
ventilated. - A rise in temperature of monitor may cause fire.
Install the monitor in stable place. - An unstable monitor may crash or fall.
Personal injury, damage, or malfunction may result.
Do not block ventilation openings with any curtain or tablecloths. - The
increase of inside temperature may cause fire
DO not drop the unit or make any scratch on the panel when you move the
product. -Any scratch on the panel or drop of the product may cause
functional failure.
When moving the monitor, turn it off and disconnect all cables and the
plug. - Product damage, electric shock, or fire hazard may result.
When disconnecting from the wall outlet, grab the plug. - Grabbing the cord
may result in heat generation or fire hazard.
IMPORTANT SAFEGUARDS
Do not press hard with your finger or scratch with sharp object on the surface
of the LCD. -Any damage on the surface of the LCD may cause functional
failure.
When you clean the monitor and the surface of LCD, be sure to pull the plug
from wall outlet. Use soft cloth instead of using damp duster.
Do not use any chemicals such as industrial polisher, abrasive solution, wax,
benzene, alcohol, or clearing detergents. - Chemical cleaners may fade,
dissolve, or crack the monitor surface.
| FCC Part 15 Notice |
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to pro-vide reasonable protection
against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not in-stalled and used
in accordance with the instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
CAUTION : Changes or modifications not expressly approved by the manufacturer responsible for
compliance could void the user’s authority to operate the equipment.
190M LCD Monitor
ACCESSORIES
ACCESSORIES
Please make sure the following accessories are provided with your LCD Monitor. If any items are missing,
contact your dealer.
Monitor AC Adapter
D-Sub Cable CD Manual(CD Title)
Quick Installation Guide Audio Cable
Warranty Card
190M LCD Monitor
PREPARATION
PREPARATION
Connection
1. Power Connection : Connect the [POWER Cable] to the power terminal on the back of the monitor.
2. Connection of PC : Connect the signal cable(D-SUB cable) to the monitor output socket of the
computer and the other end to D-SUB on the back of the monitor.
3. AUDIO IN : Connect an audio cable to AUDIO IN on the back of the Monitor and the other end to
AUDIO OUT terminal of the sound card on your computer.
AUDIO OUT : Connect an audio cable to the AUDIO OUT of the back of the Monitor and the other
end to the external speakers.
PREPARATION
Mounting Device [Separation] & [Union]
1. Separation
1) Turn off your monitor and unplug its power cord.
2) Lay the monitor face-down ward on a flat surface with a
cushion beneath it to protect the screen.
3) Remove the screws( A ) and then remove the Mounting
Device from the monitor.
4) Remove the screws( B ) and then remove the Mounting
Device from the monitor.
2. Union
1) Align the Mounting Device with the holes( B ) in the Rear
Cover and secure it with the screws.
2) Cover the Mounting Device with the Mounting Device cover
and secure it with screws( D ).
190M LCD Monitor
OPERATION
AND
CONTROL
OPERATION & CONTROL
LCD Monitor Control Overview
1) Controls
1. LCD Panel
2. Menu Button : Use this button to open the OSD and activate a highlighted menu items.
3. Select Button : Use this button to activate a highlighted menu item.
Allows the monitor to self-adjust to the incoming video signal.
4. Adjust Buttons : These buttons allow you to highlight and adjust items in the OSD.
Increases or decreases the level of speaker volume.
5. Power Button : Turns ON/OFF the monitor.
6. Built-in Speakers
OPERATION & CONTROL
2) Terminals
1. Power In Terminal
: Connect the [POWER Cable] to the power terminal on the back of the monitor.
2. D-SUB Terminal
: Connect the monitor D-SUB connector and the PC using the D-SUB signal cable.
3. AUDIO IN Terminal : Connect the audio output of the PC.
4. AUDIO OUT Terminal : Connect the stereo speaker system to Audio output.
5. VESA HOLE for fixing on the wall.
: Supports VESA mounting standard for use with various VESA mounting devices.
190M LCD Monitor
BASIC
EXPLANATION
BASIC EXPLANATION
The front part of panel of this model consists of following function buttons. Description for each of
function button is shown below.
Power Button
Turns ON/OFF the monitor.
Menu Button
Use this button to open the OSD and activate a highlighted menu items.
SELECT Button
Use this button to activate a highlighted menu item.
Allows the monitor to self-adjust to the incoming video signal.
Adjust Buttons
These buttons allow you to highlight and adjust items in the OSD.
Increases or decreases the level of speaker volume.
190M LCD Monitor
BASIC
OPERATION
BASIC OPERATION
Turning on POWER
Press MAIN POWER.
BASIC OPERATION
OSD Adjustment
Set OSD value with the instructions described below.
BASIC OPERATION
Frequently used function
1) Monitor Self-Adjust
Self-Adjust to the incoming video signal.
Press the "SELECT" Button. (SELECT -> YES -> Self-Adjust)
2) Adjust Speaker Volume
Increases or decreases the level of speaker volume.
3) Reset Factory Default
Screen parameters are replaced with the factory default values.
4) White Balance
Select this menu to use automatic color balance function.
190M LCD Monitor
DESCRIPTION
AND
DIRECTORIES
OF ALL MENUS
DESCRIPTION & DIRECTORIES OF ALL MENUS
OSD for Each Adjustment Items
1. DISPLAY ADJUST
a. BRIGHTNESS : Adjust to brighten or darken the picture.
b. CONTRAST : The contrast control determines the white level of the picture.
c. PHASE : Fine tuning of the screen even though it is not easily distinguishable with naked eyes.
d. CLOCK : Adjust the horizontal-size(size of horizontal screen)of the entire screen.
e. H-POSITION : Move the entire screen to the left or right.
f. V-POSITION : Move the entire screen to the below or upper.
g. FACTORY DEFAULT : Screen parameters are replaced with the factory default values.
2. MISC ADJUST
a. DOS MODE : Use this menu to select either 640X400 or 720X400 of Dos mode.
b. WHITE BALANCE : Select this menu to use automatic color balance function.
c. R GAIN : The user can adjust the Red Settings.
d. G GAIN : The user can adjust the Green Settings.
e. B GAIN : The user can adjust the Blue Settings.
f. COLOR TEMPERATURE : Use this menu to adjust color temperature.
3. OSD ADJUST
a. OSD H-POS : You can change the horizontal position where the OSD menu appears on your monitor
b. OSD V-POS : You can change the vertical position where the OSD menu appears on your monitor
c. OSD OFF TIME : The OSD will automatically turn off if no adjustments are made for a certain time
period.
d. OSD TRANSPARENCY : Changes the transparent(or opaque) status of the background of the OSD.
e. LANGUAGE : OSD language and appearance can be changed.
4. EXIT : Use this menu to exit from OSD menu screen.
190M LCD Monitor
VOCABULARY
VOCABULARY
Dot pitch
The image on a monitor is composed of red, green and blue dots. The closer the dots, the higher the
resolution. The distance between two dots of the same color is called the 'Dot Pitch'.
Horizontal Frequency
The time to scan one line connecting the right edge to the left edge of the screen horizontally is called
Horizontal Cycle. The inverse number of the Horizontal Cycle is called Horizontal Frequency.
Vertical Frequency
The screen must be redrawn several times per second in order to create and display an image for the
user. The frequency of this repetition per second is called Vertical Frequency or Refresh Rate.
Resolution
The number of horizontal and vertical dots used to compose the screen image is called 'resolution'.
Plug and Play
This is a function that provides the best quality screen for the user by allowing the computer and the
monitor to exchange information automatically.
190M LCD Monitor
TROUBLESHOOTING
TROUBLESHOOTING
Before calling for repair services, make the following checks for possible remedies to the encountered
symptoms.
Problem Possible Remedies
Screen is black and power indicator is off
Ensure that the power cord is firmly connected and the Monitor
is on.
Screen is black and power indicator is
blinks.
Ensure that the signal cable is firmly connected to the PC.
Ensure that the PC are turned on.
Screen position and size is incorrect. Press the AUTO Button.
Image is not stable and may appear to
vibrate.
Check that the display resolution and frequency from your PC is
an available mode for your Monitor.
On your computer check : Control Panel -> Display -> Settings.
The image is too light or too dark. Adjust the Brightness and Contrast.
Horizontal noise on the image. Adjust the AUTO.
Adjust the PHASE.
Vertical bars or stripes on the image. Adjust the AUTO.
Adjust the CLOCK.
190M LCD Monitor
SPECIFICATIONS
SPECIFICATIONS
Product Specification
MONITOR TYPE TFT LCD Flat Panel
VIEWABLE SCREEN SIZE 19.0” (48.184Cm)
RESOLUTION 1280 x 1024 (SXGA)
DISPLAY COLOR(Max.) 16.7M colors
PIXEL ARRANGMENT RGB Vertical stripe
PIXEL PITCH 0.294mm(H) x 0.294mm(V)
VIEWING ANGLES (H/V) 170 / 170 (Typ.)
RESPONSE TIME (ms) 25ms (Typ.)
CONTRAST RATIO 500:1 (Typ.)
BRIGHTNESS (cd/m²) 250 (Typ.)
OPERATING TEMPERATURE 0 (Min.), +50 (Max.)
STORAGE TEMPERATURE -20 (Min.), +60 (Max.)
RATED POWER Adapter 100-240V, 50~60Hz, DC 12V/5A
POWER CONSUMPTION MAX. 40W (standby : 3W)
POWER MANAGEMENT VESA DPMS Standard
PLUG & PLAY LEVEL VESA DDC 1/2B Compatible
BUILT-IN SPEAKERS 3W * 2 Stereo Type
VIDEO INPUT Analog/R.G.B., 0.7 Vp-p
INPUT CONNECTOR DC Power in, Audio in, VGA 15-pin D-sub
CONNECTOR OUTPUT CONNECTOR Audio out
USER CONTROLLER
KEYPAD Power, Menu, Select, Adjust Up/Down
REGULATORY APPROVAL MIC,CE,CB,TCO99
COLOR MANAGEMENT sRGB & ICC Profile
CABINET COLOR Ivory, SV, BK, Wh
DIMENSION (W X H X D) 443 x 453 x 216 mm
WEIGHT (kg) 6.95Kg(Net)
** This specification of the product might be changed without any notice.
SPECIFICATIONS
Display Mode
RESOLUTION
REFRESH
RATE
HORIZONTAL
FREQUENCY
PIXEL
FREQUENCY
STANDARD TYPE
640 X 350 70 Hz 31.5 KHz 25.175 MH VESA Standard
640 X 400 70 Hz 31.5 KHz 25.175 MH VESA Standard
720 X 350 70 Hz 31.5 KHz 28.35 MHz VESA Standard
60 Hz 31.5 KHz 25.175 MH Industry Standard
72 Hz 37.9 KHz 31.500 MHz VESA Standard
640 X480
75 Hz 37.5 KHz 31.500 MHz VESA Standard
56 Hz 35.1 KHz 36.600 MHz VESA Guidelines
60 Hz 37.9 KHz 40.000 MHz VESA Guidelines
72 Hz 48.1 KHz 50.000 MHz VESA Standard
800 X 600
75 Hz 46.9 KHz 49.500 MHz VESA Standard
43 Hz 35.5 KHz 44.900 MHz Industry Standard
60 Hz 48.4 KHz 65.000 MHz VESA Guidelines
70 Hz 56.5 KHz 75.000 MHz VESA Standard
1024 X 768
75 Hz 60.0 KHz 78.750 MHz VESA Standard
1152 X 864 75 Hz 67.5 KHz 108.000 MHz
VESA Standard
60 Hz 64.0 KHz 108.000 MHz
VESA Standard
1280 x 1024 75 Hz 80.0 KHz 135.000 MHz
VESA Standard