BTI Wireless LPA2100 Multi-Carrier Power Amplifier User Manual

Bravo Tech (Shenzhen) Co. Ltd. Multi-Carrier Power Amplifier Users Manual

UserManual.wiki >

LPA2100 User Manual

Users Manual

LPA2100-160-SW01 BRAVO TECH INC Add.: 6185 Phyllis Drive Unit D, Cypress, CA 90630 Phone: 1-714-230-8333 Website: www.bravotechinc.com Revision: SP·LPA2100-160-SW01·REV.APage: 1 LPA2100-160-SW01 SPECIFICATION 1. System advantages Bravo Tech Inc 's newly introduced Multi-Carrier High Power Outdoor Booster platform provides higher downlink EIRP and improved uplink sensitivity at the same time to extend the coverage of existing cellular networks. This multi-carrier based product platform can also work with customized BTS to extend capacity of original BTS with a low system total cost. This product platform features: • Support multi-carrier CDMA signals, with mixed mode operation • Output maximum power 160W, support carriers number up to 4. • Very High System Efficiency • Extensive product monitoring and control (local and remote) • Centralized system control/display/alarms • Great system reliability supported by architecture built-in redundancy • Powered by 30VDCavailable • Extensive protection for lightning, voltage surge, and any high failure rate assemblies • Compact system size and light weight 2. System Block Diagram

LPA2100-160-SW01 BRAVO TECH INC Add.: 6185 Phyllis Drive Unit D, Cypress, CA 90630 Phone: 1-714-230-8333 Website: www.bravotechinc.com Revision: SP·LPA2100-160-SW01·REV.APage: 2 3. Electrical Specifications PARAMETER SPECIFICATION Frequency 2110 ~ 2155 MHz Output Power 160Watts average max. ( CDMA2000, PAR：8.0dB) Spurious Emission -45dBc@∆f=885-1.25MHz, 30kHz RBW -55dBc@∆f=1.25-1.98MHz, 30kHz RBW -55dBc@∆f=1.25-2.25MHz, 30kHz RBW -13dBm@∆f=2.25-4MHz, 30kHz RBW RF Gain 57.0 ± 1.0dB @ frequency range, +30Vdc, room temp. Normal Operating Voltage +30Vdc±1.0Vdc Operating Voltage +29Vdc ~ +31Vdc RF Gain Variation over Voltage & Temperature ±1.5dB @ +29≤Vsup≤+31V, -20℃ to +50℃ Gain Flatness Peak to Peak 0.2dB over any 5MHz Input/Output Return Loss -16dB min. Output Protection Mismatch protected with isolator Efficiency ≥12%@+30Volts, Po=+52dBm Operating Temperature -20℃ to +50℃ (Air Temperature inside System), Operating point Output power:52.5dBm ± 0.5dB Operating range 6dB min Input Power ALC Over Pwr Output Pwr:53dBm ± 0.5dB 4. Alarm and Functions Specifications TTL output for the alarm pins. Normal is High, Alarm is Low. 4.1 Over temperature alarm Alarm and shutdown at 85 base temperature, auto℃-recover at 65 base temperature.℃ 4.2 Over power alarm Alarm and shutdown when output power is over 52.5dBm, no auto-recover. 4.3 ALC 4.3.1 ALC level: 52.5±0.5dBm 4.3.2 ALC range: ≥6dB 4.4 Over driver alarm Alarm and shutdown when input power is over+1dBm, no auto-recover. 4.5 Transistor fail alarm Alarm and shutdown when gain reduce 10dB, no auto-recover 4.6 VSWR alarm Alarm and shutdown when reject is over 43dBm, no auto-recover.

LPA2100-160-SW01 BRAVO TECH INC Add.: 6185 Phyllis Drive Unit D, Cypress, CA 90630 Phone: 1-714-230-8333 Website: www.bravotechinc.com Revision: SP·LPA2100-160-SW01·REV.APage: 3 5. Description of the connectors 5.1 RF Part Port Name Type Warning Input SMA Female (50Ω) Normal :-5.2dBm maxium input power +1dBm. Output N Female (50Ω) Normal :51.76dBm maxium output power 52.5dBm. 5.2 DC power Port Name Type NO Warning A1、A2 VDC type +30V, range 24~32V DC IN D-Sub type DSCD175PS1M (Male) A3、A4 GND to VDC 5.3 Communication Connector type: USB Note: Manufacter use to debug. 5.4 LED Indication Figure 1 Power Amplifier Indicators Table 1 Specification of Power Amplifier Indicator Light Item Label Color State Specification MAJOR ALM Red On MINOR ALM Yellow Off 1 RF ON Green Off Power amplifier alarms and shuts down MAJOR ALM Red Off MINOR ALM Yellow On 2 RF ON Green Off Power amplifier alarms but still works MAJOR ALM Red Off MINOR ALM Yellow Off 3 RF ON Green On Power amplifier works normally

LPA2100-160-SW01 BRAVO TECH INC Add.: 6185 Phyllis Drive Unit D, Cypress, CA 90630 Phone: 1-714-230-8333 Website: www.bravotechinc.com Revision: SP·LPA2100-160-SW01·REV.APage: 4 5.5 Warning 1. Check the power supply voltage is between 24V and 32V or not before electrify, better to setup in 30V. Power of power supply shall bigger than 1400W. 2. Ensure the power supply polarity is right, port A1、A2 are anode, and port A3、A4 are cathode. 3. Ensure the output line is connected and input power is not over load before connect the RF input line. 4. Use the type N connector as output connector, for the high output power, suggest to using the φ3 upwards RF cable to connect. At the same time, output matching demand all right, SWR more than 1.5 is better, but less than 3.0. 5. Product operating should be cooled by air flow, air flow more than 150cfm. 6. Product operating room temperature can’t above 50o ,also can’t below -20o。

LPA2100-160-SW01 BRAVO TECH INC Add.: 6185 Phyllis Drive Unit D, Cypress, CA 90630 Phone: 1-714-230-8333 Website: www.bravotechinc.com Revision: SP·LPA2100-160-SW01·REV.APage: 5 6. Dimension Figure 2 Dimension 345 450 Left Right FrontRear Unit: mm

LPA2100-160-SW01 BRAVO TECH INC Add.: 6185 Phyllis Drive Unit D, Cypress, CA 90630 Phone: 1-714-230-8333 Website: www.bravotechinc.com Revision: SP·LPA2100-160-SW01·REV.APage: 6 Figure 3 Mechanical drawing

LPA2100-160-SW01 BRAVO TECH INC Add.: 6185 Phyllis Drive Unit D, Cypress, CA 90630 Phone: 1-714-230-8333 Website: www.bravotechinc.com Revision: SP·LPA2100-160-SW01·REV.APage: 7 7. Assembled Figure 4 Assembled Instructions 1. Lock 5 screws 4-40, L3/8 inch with Philip's type screwdriver to fasten the front side of PA to the Front Plate of Booster as shown above. 2. Lock 3 screws 4-40, L5/8 inch with Philip's type screwdriver to fasten the back side of PA to a connection board which is connected to the soleplate of Booster. 5 screws 4-40, L3/8 inch 3 screws 4-40, L5/8 inch

Navigation menu