User Manual
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 3381824 |
| Application ID | ioeOzgyo96GTLLWDIZx40Q== |
| Document Description | User Manual |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 20.27kB (253380 bits) |
| Date Submitted | 2017-05-08 00:00:00 |
| Date Available | 2017-05-08 00:00:00 |
| Creation Date | 2017-03-17 16:10:30 |
| Producing Software | Adobe PDF Library 15.0 |
| Document Lastmod | 2017-03-17 16:10:30 |
| Document Title | User Manual |
| Document Creator | Adobe InDesign CC 2017 (Macintosh) |
Programming Electronic Limit Roller Shade Motors One Channel Remote Instructions Handsender Layout INPUT INDICATOR (LED) For the following commands, the motor must be placed into either “Pairing Mode” or “Programming Mode”. Pairing Mode OPEN To Enter Pairing Mode, disconnect power to the motor for 3-5 seconds, then reconnect. Alternate method: If handsender is already Paired, then hold STOP for approximately 5 seconds. Note that the motor will stay in Pairing Mode for 2 minutes. The motor will time out on it’s own, and you do not need to save and exit from Pairing Mode. STOP CLOSE Expected Response: Pair Handsender to Motor / Learn Channel Motor must be in Pairing Mode Hold Open and Close. Fn - The handsender will give a slow blink. - After 3-5 seconds, the motor will jog. - Motor will now work on this channel. Delete Channel from Motor Motor must be in Pairing Mode Hold Stop and Open. - The handsender will give a slow blink. - After 3-5 seconds, the motor will jog. - Motor will no longer respond to this channel. Delete All Channels Motor must be in Pairing Mode Hold Stop and Close. - The handsender will give a slow blink. - After 3-5 seconds, the motor will jog. - Motor will no longer respond to any channel. Programming Mode To enter Programming Mode, press and hold FN+STOP for approximately 5 seconds (until motor jogs). Note that all of these settings can be made without exiting from Programming Mode after each change (they can all be done in the same session). Programming mode lasts for 2 minutes. If you do not exit and save before the 2 minutes has expired, the motor will exit programming mode and cancel all changes. Reverse Motor Direction Motor must be in Programming Mode Hold Open and Close. Wait for motor to jog, then... continue with other programming options or hold Stop to save and exit. Expected Response: - The handsender will give a slow blink. - After 3-5 seconds, the motor will jog. Touch Control On/Off (Tumo Drapery Motor Only) Expected Response: Motor must be in Programming Mode Hold Fn and CLOSE to turn Touch Control off or... - The handsender will give a slow blink. - After 3-5 seconds, the motor will jog. - Touch Control is now OFF. - The handsender will give a fast blink. - After 3-5 seconds, the motor will jog. - Travel direction is now reversed. Hold Fn and OPEN to turn Touch Control on, then... - The handsender will give a slow blink. - After 3-5 seconds, the motor will jog. - Touch Control is now ON. - Shade will move to desired open position. continue with other programming options or hold Stop to save and exit. - The handsender will give a fast blink. - After 3-5 seconds, the motor will jog. - Settings are saved - Motor has left programming mode. Set Limits Motor must be in Programming Mode Hold Open to move shade to desired open position, then... hold Fn and OPEN to set upper limit, then... hold Close to move shade to desired close position, then... - The handsender will give a slow blink. - After 3-5 seconds, the motor will jog. - Upper limit is now set. - Shade will move to desired close position. hold Fn and CLOSE to set lower limit, then... - The handsender will give a slow blink. - After 3-5 seconds, the motor will jog. - Lower limit is now set. continue with other programming options or hold Stop to save and exit. - The handsender will give a fast blink. - After 3-5 seconds, the motor will jog. - Limits are now set. - Motor has left programming mode. © 2017 BTX Intelligent Fashion, LLC. Programming - 490.2076 - 012317 www.btxinc.com | 800-422-8839 FCC Caution § 15.19 Labelling requirements. This device complies with par t 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful inter ference, and (2) this device must accept any inter ference received, including inter ference that may cause undesired operation. § 15.21 Information to user. Any Changes or modifications not expressly approved by the par ty responsible for compliance could void the user’s authority to operate the equipment. § 15.105 Information to the user. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to par t 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful inter ference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful inter ference to radio communications. However, there is no guarantee that inter ference will not occur in a par ticular installation. If this equipment does cause harmful inter ference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the inter ference by one or more of the following measures: -Reorient or relocate the receiving antenna. -Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help. FCC ID: UGP-4902077
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : No Language : en-US XMP Toolkit : Adobe XMP Core 5.6-c137 79.159768, 2016/08/11-13:24:42 Create Date : 2017:03:17 16:10:30-05:00 Metadata Date : 2017:03:17 16:10:30-05:00 Modify Date : 2017:03:17 16:10:30-05:00 Creator Tool : Adobe InDesign CC 2017 (Macintosh) Instance ID : uuid:81d1f809-f3d9-124f-8106-2e2667721504 Original Document ID : xmp.did:d95eb9d7-a441-4232-8a4b-da3ba08a5ba9 Document ID : xmp.id:8e0e16b0-601f-45a7-9c32-64ca3d66f409 Rendition Class : proof:pdf Derived From Instance ID : xmp.iid:45a40109-1519-4dce-ad7b-973e0cd6e44e Derived From Document ID : xmp.did:45a40109-1519-4dce-ad7b-973e0cd6e44e Derived From Original Document ID: xmp.did:d95eb9d7-a441-4232-8a4b-da3ba08a5ba9 Derived From Rendition Class : default History Action : converted History Parameters : from application/x-indesign to application/pdf History Software Agent : Adobe InDesign CC 2017 (Macintosh) History Changed : / History When : 2017:03:17 16:10:30-05:00 Format : application/pdf Producer : Adobe PDF Library 15.0 Trapped : False Page Count : 2 Creator : Adobe InDesign CC 2017 (Macintosh)EXIF Metadata provided by EXIF.tools