BUFFALO 09101466-0 802.11n Wireless miniPCI User Manual

BUFFALO INC. 802.11n Wireless miniPCI Users Manual

Manual

PDBU-31119-X000-A0  1/8BUFFALO INC.User’s manual of 802.11n miniPCI            BUFFALO INC. Broadband Solutions Business Unit Product Name：802.11n Wireless miniPCIProduct Number：WZR-G300NDocument Number：PDBU-31119-X000-A0Rev. Date Description of change Prepared byA0 2006/04/19 first edition Nakazono(YKK-013-04)
PDBU-31119-X000-A0  2/8BUFFALO INC.Table of Contents1. Introduction2. System block diagram3. Product Spec3-1. System Configration3-2. Basic Spec4. Outline Dimension5. Manufacturing Test5-1. Instruction5-2. Test Configration5-3. Test Flow and Criteria6. Assembly and Label information6-1. Instruction6-2. Assembly drawing6-3. Label Drawing7. Packaging and Shipment7-1. Instruction7-2. Packing drawing7-3. Shipment method8. Restrictions about production 8-1. Manufacturers of aluminum electrolytic capacitor which BUFFALO approves 8-2. Manufacturers where BUFFALO prohibited use9. Federal Communication Commission Interference Statement
PDBU-31119-X000-A0  3/8BUFFALO INC.1. IntroductionThis document describes the design specifications of 802.11n Wireless miniPCI.This product guarantees compatibility with IEEE 802.11n draft compliant goods.And this product is compatible with IEEE802.11b/g legacy goods.2. System block diagramPower SupplyDipole AntennaAntenna Switch TX PAAntenna SwitchPCI BusRegulator PCI bus+3.3V+2.5V+1.8VWZR-G300N BLOCK DIAGRAMDipole AntennaDipole AntennaAntenna SwitchTX PAMAC, B/B(4321)Transceiver(2055)
PDBU-31119-X000-A0  4/8BUFFALO INC.3. Product Spec3-1. System ConfigrationITEM ContentsInterface / System bus support PCIStandard IEEE 802.11g、802.11bData rete (Mbps) 54,48,36,24,18,12,9,6,11,5.5,2,120MHz BW: 130,117,104,78,52,39,26,1340MHz BW: 270,243,216,162,108,81,54,27Modulation PSK/CCK,DQPSK,DBPSK,OFDMNetwork architectures Infrastructure and ad hocOperating channels 2.4GHz: 11 for North America, 13 for Europe, and 14 for JapanRF Output Power 2x2: 2.4GHz 11n 15 dBm2x2: 2.4GHz 11g 18 dBm2x2: 2.4GHz 11b 17 dBmAntenna connectors U.FL-R-SMT-1(10) HIROSE or compatibility connectorPower requirements DC 3.3VPower consumption Average standby < 20mWSecurity IEEE 802.1x, WEP/WEP2, WPA/WPA2, TKIP, Weak-key avoidance, CCX, CCX2.0, CCX3.0, 128bit OCB mode AES, IEEE 802.11iCertifications IEEE 802.11-compliant, Wi-Fi CERTIFIED, ACPI power management3-2. Basic SpecBasic Spec ContentsGarver version WMIB-200GN_V02Schematic version WMIB-200GN_V02SBOM version 970-300-0035RWeight 25gReglation Japan MIC（Telec） ○ （apply by Buffalo）FCC ClassB ○CE ○Wifi ○ (apply by Buffalo)
PDBU-31119-X000-A0  5/8BUFFALO INC.4. Outline Dimension
PDBU-31119-X000-A0  6/8BUFFALO INC.5. Manufacturing TestThe production company must report test result of wireless to BUFFALO in production test.It must show that a produced product satisfies TELEC standard.5-1. Instruction5-2. Test Configration5-3. Test Flow and Criteria6. Assembly and Label information6-1. Instruction6-2.Assembly drawing6-3.Label Drawing7. Packaging and Shipment7-1. Instruction7-2. Packing drawing7-3. Shipment method8. Restrictions about production 8-1. Manufacturers of aluminum electrolytic capacitor which BUFFALO approvesChoose aluminum electrolytic capacitor among the following manufacturers.凱美電機（ＪＡＭＩＣＯＮ）智寶（ＴＥＡＰＯ）世昕（ＬＵＸＯＮ）ＴＡＩＣＯＮ輝城(L-tec) 8-2. Manufacturers where BUFFALO prohibited useThe aluminum electrolytic capacitor must not use the following manufacturers.GloriaLELON(立隆)FuhjyyuThe ceramic condenser must not use the following manufacturers.PanOverSeaTeamYoung（天揚）The PCB must not use the following manufacturers.TOPSEARCH
PDBU-31119-X000-A0  7/8BUFFALO INC.9. Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device,pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protectionagainst harmful interference in a residential installation. This equipment generates, uses and canradiate radio frequency energy and, if not installed and used in accordance with the instructions, maycause harmful interference to radio communications. However, there is no guarantee that interferencewill not occur in a particular installation. If this equipment does cause harmful interference to radio ortelevision reception, which can be determined by turning the equipment off and on, the user isencouraged to try to correct the interference by one of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. This device complies with Part 15 of the FCC Rules. Operation is subject to the following twoconditions: (1) This device may not cause harmful interference, and (2) this device must accept anyinterference received, including interference that may cause undesired operation. FCC Caution: Any changes or modifications not expressly approved by the party responsible forcompliance could void the user's authority to operate this equipment. IMPORTANT NOTE: FCC Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolledenvironment. This equipment should be installed and operated with minimum distance 20cmbetween the radiator & your body. This transmitter must not be co-located or operating in conjunction with any other antenna ortransmitter. Buffalo declares that WZR-G300N (FCC ID: FDI-09101466-0) is limited in CH1~CH11 for 2.4GHz by specified firmware controlled in U.S.A.
PDBU-31119-X000-A0  8/8BUFFALO INC.This device is intended only for OEM integrators under the following conditions:1) The antenna must be installed such that 20 cm is maintained between the antenna andusers, and 2) The transmitter module may not be co-located with any other transmitter or antenna.As long as 2 conditions above are met, further transmitter test will not be required. However, theOEM integrator is still responsible for testing their end-product for any additional compliancerequirements required with this module installed (for example, digital device emissions, PCperipheral requirements, etc.).IMPORTANT NOTE: In the event that these conditions can not be met (for example certain laptopconfigurations or co-location with another transmitter), then the FCC authorization is no longerconsidered valid and the FCC ID can not be used on the final product. In these circumstances, theOEM integrator will be responsible for re-evaluating the end product (including the transmitter) andobtaining a separate FCC authorization.End Product LabelingThis transmitter module is authorized only for use in device where the antenna may be installedsuch that 20 cm may be maintained between the antenna and users (for example: Access point,Router…etc). The final end product must be labeled in a visible area with the following: “ContainsTX FCC ID: FDI-09101466-0”.Manual Information That Must be IncludedThe OEM integrator has to be aware not to provide information to the end user regarding how toinstall or remove this RF module in the users manual of the end product which integrate thismodule.The users manual for OEM integrators must include the following information in a prominentlocation “ IMPORTANT NOTE: To comply with FCC RF exposure compliance requirements, theantenna used for this transmitter must be installed to provide a separation distance of at least 20cm from all persons and must not be co-located or operating in conjunction with any other antennaor transmitter.

Navigation menu