BaBaiBa Technology MPSPG96 Aluminium Tube Bluetooth Selfie Stick User Manual
Shenzhen BaBaiBa Technology Co., Ltd. Aluminium Tube Bluetooth Selfie Stick
User manual
Adjustable smartphone mount can support practically
any smartphone or phablet. Strong and sturdy
enough for any smartphone. Expands up to 3.5” wide.
The head can be adjusted to allow for 180° movement
and settings. Loosen the lock knob to position your
head and tighten it once you have achieved your
desired position. Folds inward for compact storage.
You can also remove the smartphone holder and
mount a GoPro directly to the SelfieStick, or mount a
point & shoot camera via the included 1/4”-20 mount.
SelfieStick has five “twist and lock” sections. To
deploy the sections, grasp the foam grip in one hand
and the smartphone holder in the other hand.
Rotate the grip counter-clockwise. You will feel each
section unlock with each slight rotation. Once all of
the sections are unlocked, extend the SelfieStick to
your desired length. Then rotate clockwise to lock the
sections in place.
Bluetooth shutter release with buttons for Apple and
Android. You can control the functions on your
smartphone or phablet up to 30 feet away from the
SelfieStick.
The SelfieStick comes with a foam grip on the bottom
section so you can comfortably and securely grip your
SelfieStick.
Owner’s Manual
Aluminium Tube Bluetooth Selfie Stick
Specifications:
Compatibility: Apple, Android
Load capacity: 1 lb.
Weight: 6 oz.
Maximum length: 34.5 in.
Minimum length: 10 in.
Leg sections: 5
Leg material: aluminum
Maximum working distance: 30 feet
Warranty: 1 year
Product design and specifications subject to change without notice.
How to use:
1. On initial use, charge the SelfieStick for 1 hour by con-
necting the included cable between the micro USB input
on the bottom of the Selfie Stick, and a USB charging
device.
2. Slide the On/Off Switch located on the bottom of the
SelfieStick to “On”. The LED will begin to blink.
3. Turn on your smartphone’s Bluetooth function.
4. When your phone has found “Sunpak” pair to that
device. Once paired, the LED will turn off and you can
go the camera functions on your phone.
5. Attach your phone to the adjustable mount of the
SelfieStick.
6. Twist the foam grip section counter-clockwise to unlock
the sections. Extend to your desired length and twist
clockwise to lock the sections.
7. Press the Shutter Release button on the SelfieStick to
take a picture or video.
8. Unscrew and remove the lock screw to mount a GoPro
or the Point & Shoot adapter to the SelfieStick.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not
cause harmful interference, and (2) this device must accept any interference received, including interference that may cause
undesired operation.
Caution: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to
operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This
equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
--Reorient or relocate the receiving antenna.
--Increase the separation between the equipment and receiver.
--Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
--Consult the dealer or an experienced radio/TV technician for help.