Baicells Technologies EG7035 LTE Outdoor CPE User Manual BaiCells EG7035

Download:
Mirror Download [FCC.gov]
Document ID	3037256
Application ID	vXjJtknVbJc5j+ylY1/ozA==
Document Description	Users Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	191.63kB (2395340 bits)
Date Submitted	2016-06-22 00:00:00
Date Available	2016-06-28 00:00:00
Creation Date	2017-12-08 19:45:46
Producing Software	GPL Ghostscript 9.18
Document Lastmod	2017-12-08 19:45:46
Document Title	BaiCells EG7035 User Manual
Document Creator	Microsoft® Word 2010
Document Author:	admin

BaiCells EG7035 User Manual
V1.0
All rights reserved © BaiCells Technologies Co., Ltd.
About This Document
This document introduces the specifications of BaiCells EG7035 CPE and guides users to
install and configure it.
Copyright Notice
BaiCells copyrights this specification. No part of this specification may be reproduced in
any form or means, without the prior written consent of BaiCells.
Disclaimer
This specification is preliminary and is subject to change at any time without notice.
BaiCells assumes no responsibility for any errors contained herein. For more information,
please consult our technical engineers.
Revision Record
Date
15 Jun,2015
Version
Description
Author
V1.0
Initial released.
Tang Houcheng
Contact Us
E-mail: support@baicells.com
Phone: 86-10-62607100
Website: http://www.baicells.com/
Contents
1.
2.
3.
Product Overview ....................................................................................................... 1
1.1
Introduction .............................................................................................................. 1
1.2
Features ..................................................................................................................... 1
1.3
Product Description.................................................................................................... 2
1.4
Appearance ............................................................................................................... 2
1.5
Interface and Button ................................................................................................ 3
1.6
LED Indicators ........................................................................................................... 3
Technical Specifications ............................................................................................... 4
2.1
Basic Specification .................................................................................................... 4
2.2
RF Specification ........................................................................................................ 4
2.3
SW Specification ....................................................................................................... 4
2.4
Device Management .................................................................................................. 5
2.5
Environment Specification ......................................................................................... 5
2.6
Regulatory Compliance .............................................................................................. 6
Product Installation....................................................................................................... 8
1.1 Installation Steps ............................................................................................................. 8
4.
CPE Configuration ....................................................................................................... 9
4.1
Log in .......................................................................................................................... 9
4.2
Basic Configuration .................................................................................................... 9
4.2.1
Network Mode.................................................................................................... 9
4.2.2
LTE Setting ........................................................................................................ 10
4.2.3
Setting Connect Method .................................................................................. 11
4.2.4
Manual Connect Network ................................................................................ 11
4.2.5
Setting Scan Mode ............................................................................................ 12
4.2.6
Setting Frequency (Earfcn) ............................................................................... 12
4.2.7
APN Management ............................................................................................ 13
Appendix A
FAQs......................................................................................................... 14
A.1
The POWER indicator does not turn on. .................................................................. 14
A.2
Fails to Login to the web management page. .......................................................... 14
A.3
The CPE fails to search for the wireless network. .................................................... 14
A.4
The power adapter of the CPE is overheated. ......................................................... 14
A.5
The parameters are restored to default values. ...................................................... 14
Appendix B
Product List .............................................................................................. 15
Contents of Figure
Figure 1-1 EG7035 Appearance .................................................................................. 2
Figure 1-2 Interface and Button of EG7035 ................................................................. 3
Figure 3-1 Install the Sample .......................................................................................... 8
Figure 3-2 Connection Diagram ...................................................................................... 8
Figure 4-1 Login Page .................................................................................................. 9
Figure 4-2 Setup Network Mod .................................................................................. 10
Figure 4-3 LTE Setting................................................................................................ 10
Figure 4-4 Setup Connect Method ............................................................................. 11
Figure 4-5 Setup Scan Mode ..................................................................................... 12
Figure 4-6 Setting frequency ...................................................................................... 13
Figure 4-7 APN Management ..................................................................................... 13
Contents of Table
Table 1-1 EG7035 Product Description ........................................................................ 2
Table 1-2 EG7035 Appearance Index .......................................................................... 2
Table 1-3 Description of EG7035 Interface and Button ............................................... 3
Table 1-4 LED Indicators .............................................................................................. 3
Table 2-1 Basic Specification ....................................................................................... 4
Table 2-2 RF Specification ........................................................................................... 4
Table 2-3 SW Specification .......................................................................................... 4
Table 2-4 Device Management..................................................................................... 5
Table 2-5 Environment Specification ............................................................................ 6
1. Product Overview
1.1
Introduction
Baicells is a high-tech company dedicated in wireless broadband access solutions and
service operation. With the advent of the Internet+ era, the development of WBB is
imminent. Through continuous innovation, Baicells launches the world first mobile
broadband system based on the Internet architecture and unlicensed spectrum.
Baicells can provide serious CPEs, include indoor and outdoor unit on different
spectrums.
Baicells EG7035 is a high performance outdoor CPE. EG7035 has the superior
wireless access performance and comprehensive routing capabilities, which have the
abilities to bring the end-users WBB services.
1.2
Features
EG7035 is designed according to the simplicity principle, which can evolve in a short
period and realize fast customization, delivery and deployment as well. The main
features of EG7035 is as follows:

Support TD-LTE network according to the operator’s choice.

LTE comply to 3GPP Release9 CAT4.

LTE TDD 3650MHz - 3700MHz

Support the 100Mbps Ethernet WAN.

Intuitionist and convenient Web-based management.

Built-in LTE bipolar directional high gain antenna.

Support TR069 and OMA-DM network management protocol.

Support Cell lock. SIM lock. Pin lock.

User-friendly design of LED indicator.

Power supply with PoE.

Protection support IP67.

Support pole installation or wall mounting.
1.3
Product Description
EG7035 CPE product is shown in Table 1-1.
Table 1-1 EG7035 Product Description
Product
EG7035
1.4
Description
3.65G LTE Customer Premise Equipment
Appearance
The appearance of EG7035 is shown in Figure 1-1, and is described in Table 1-2.
Figure 1-1 EG7035 Appearance
Table 1-2 EG7035 Appearance Index
Index
Dimension
Weight
Color
Description
About 280mm * 280mm * 135mm
About 1000g
French grey
1.5
Interface and Button
The interface of EG7035 is shown in Figure 1-2, and is described in Table 1-3.
Figure 1-2 Interface and Button of EG7035
Table 1-3 Description of EG7035 Interface and Button
Connectors
ETH RJ45
USIM Slot
Restore Button
1.6
Description
One LAN
Support 1.8V/3.0V USIM
Long press over 10s to restore the factory settings
LED Indicators
Table 1-4 LED Indicators
LED Name
PWR
LTE Signal
LAN
Description
Power
Indicator
3 LTEs,
Indicate
connection
state and
signal
strength
Color LED Behavior
Green OFF
Steady On
Green All OFF
ALL blanking
One LED Steady
On
Two LED Steady
On
Three LED Steady
On
Eth Indication Green OFF
Steady On
Blanking
Status Indicator
No Power Supply
Power On
No Connected
Connecting
Connected, the
signal is weak
Connected, the
signal is medium
Connected, the
signal is strong
Ethernet connection
is not established
Ethernet connection
is normal
Ethernet interface
data being
transmitted
2. Technical Specifications
2.1
Basic Specification
Table 2-1 Basic Specification
Specification
LTE Standard
Ethernet LAN
Port
LED Indicators
USIM
Restore Button
Description
3GPP Release 9
One RJ-45 port 10/100
auto-sensing, auto-MDX, 12V ~
24V PoE
Power/LET Signal/LAN Indicator
Support 1.8V/3.3V 2FF USIM
Tact Button
Power Supply


2.2
Input: Universal range
100~240V AC
Output: 12V 1A
Comment
None
None
None
None
Long press over 10s
to restore the
factory settings
None
RF Specification
Table 2-2 RF Specification
Feature
Capability
Value
LTE Mode
Channel Bandwidth
MAX Output Power
LTE Standard
Frequency
Antenna Gain
2.3
TDD LTE
5/10/15/20
17
3GPP R9
3650 ~ 3700
19.5
Unit
None
MHz
dBm
None
MHz
dBi
SW Specification
Table 2-3 SW Specification
Item
Language Settings
Network Mode
Description
English
Bridge / NAT
SIM
Network Connection
setup
LTE Scan Mode
VPN
NAT
Statistics
2.4

















PIN Management
SIM Lock
Create, delete, and edit APNs
Set up dial-up connection automatically
Set up dial-up connection manual
Full Band
Cell Lock
Band / Frequency Preferred
Support VPN pass through
Support PPTP tunnel mode
Port forwarding
Port trigger
DMZ
UPnP
LAN Link Status
Transmit / Receive traffic
Running Time
Device Management
Table 2-4 Device Management
Item
Maintenance
TR069
Port mirror
Syslog
Diagnostics
2.5
Description
 Date & Time setting
 Reset
 Restore factory settings
 Restore/Backup Configuration File
 Local upgrade
 FOTA upgrade
Can enable or disable TR069 Management
Can enable or disable the port mirror function
Support the syslog function can send the log to the
PC via LAN
Support the Ping and trace route
Environment Specification
Table 2-5 Environment Specification
Feature
Operating Temperature
Storage Temperature
Operating Humidity
Drop
Protected Level
2.6
Capability
-40℃ ~ 55℃
-40℃ ~ 70℃
5% ~ 95%
0.8m
IP67
Regulatory Compliance
FCC Compliance
This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference,
and (2) this device must accept any interference received, including interference
that may cause undesired operation.
Any Changes or modifications not expressly approved by the party responsible
for compliance could void the user's authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential
installation. This equipment generates uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following
measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.

Consult the dealer or an experienced radio/TV technician for help.
Warning
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated
with minimum distance 20 cm between the radiator & your body.
IC Compliance
This device complies with Industry Canada licence-exempt RSS standard(s).
Operation is subject to the following two conditions: (1) This device may not cau
se interference, and (2) This device must accept any interference, including inter
ference that may cause undesired operation of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux ap
pareils radio exempts de licence.
L'exploitation est autorisée aux deux conditions suivantes:
(1) l'appareil ne doit pas produire de brouillage, et
(2) l'utilisateur de l'appareil doit accepter tout brouillage
radioélectrique subi, même si le
brouillage est susceptible d'en compromettre le fonctionnement.
The antenna(s) used for this transmitter must be installed to provide a
separation distance of at least 20 cm from all persons and must not be
collocated or operating in conjunction with any other antenna or transmitter,
End-Users must be provided with transmitter operation conditions for satisfying
RF exposure compliance.
3. Product Installation
1.1
Installation Steps
1. Assemble waterproof parts. Plug cable local connection, as shown in Figure 3-1.
2. Open the waterproof cover, and according to the instructions on the SIM card.
3. Connected to the adapter, Pay attention to the adapter interface identify.
Figure 3-1 Install the Sample
4. Mount adapter, and electricity, you can see the LED turn light, as shown in Figure
3-1.
Figure 3-2 Connection Diagram
4. CPE Configuration
4.1
Log in
By using a Web browser to login the CPE management page, the CPE configuration
management. Log on to the Web management page steps are as follows:
1. Power on.
2. In the address column of browser, type in http://192.168.1.1, then press Enter ,
login in page is shown in Figure 4-1.
Figure 4-1 Login Page
3. Enter the user name and password, click "Login" button. After password
authentication, you can log on to the web management page.
The default user name/password:
admin/admin.
In order to more secure your data, it is recommended that you open the firewall,
and keep your login password, WLAN FTP passwords and password.
4.2
Basic Configuration
4.2.1 Network Mode
To set the network mode, perform the following steps:
1. Choose Network Setting>Network Mode.
2. In the Network Mode area, select a mode between Route and Bridge.
3. Click Submit .
Figure 4-2 Setup Network Mod
4.2.2 LTE Setting
To set the LTE Network, perform the following steps:
1. Choose Network Setting>LTE Setting.
2. In the LTE Setting area, you can configure the LTE network.
3. In the LTE Setting area, you can also view the network information such as
frequency, DL&UL MCS, RSRP, RSRQ, CINR, SINR, Tx Power, Cell ID, PCI, MCC and
MNC.
Figure 4-3 LTE Setting
10
4.2.3 Setting Connect Method
To set the LTE network connect method, perform the following steps:
1. Choose Network Setting>LTE Setting.
2. In the LTE Setting area, you can set the connect method.
3. There are two methods to connect the LTE network, it is needed to choose a
method between Auto and Manual, if you want to auto connect to the LET
network you should choose the Auto, otherwise you should choose Manual.
4. Click Submit .
Figure 4-4 Setup Connect Method
4.2.4 Manual Connect Network
To manual connect the network, perform the following steps:
1. Choose Network Setting>LTE Setting.
2. Set the Connect Method to Manual.
3. Click PLMN to scan the network and select a network you want to connect. If you
don’t want to use this function, it will auto select a network to connect.
4. If you want to connect to the LTE network, you should click connect button to
connect the network, otherwise you can click the button Disconnect to
disconnect from LTE network.
11
4.2.5 Setting Scan Mode
To set the LTE network scan mode, perform the following steps:
1. Choose Network Setting>LTE Setting.
2. In the LTE setting area, you can set the scan mode.
3. You can choose full Band, PCI Lock, or a band the CPE supported.
Figure 4-5 Setup Scan Mode
4.2.6 Setting Frequency (Earfcn)
To set the frequency, perform the following steps:
1. Choose Network Setting>LTE Setting.
2. In the LTE setting area, click to set the frequency.
3. In the Frequency Setting area, you can choose a band, then click Add list to
choose an Earfcn Number.
4. Click Submit .
12
Figure 4-6 Setting frequency
4.2.7 APN Management
1. To set and manage APN, perform the following steps:
2. Choose Network Setting>APN Management.
3. In the APN Management area, you can set the APN.
4. Choose an APN number which you want to set.
5. In the APN Setting area you can set the APN parameters, such as enable or
disable the APN, APN name, username, password and so on.
6. If you want set an APN as default gateway, you should check that is enabled.
7. Click Submit .
Figure 4-7 APN Management
13
Appendix A FAQs
A.1
The POWER indicator does not turn on.

Make sure that the power cable is connected properly and the CPE is
powered on.

Make sure that the power adapter is compatible with the CPE.
A.2
Fails to Login to the web management page.

Make sure that the CPE is started.

Verify that the CPE is correctly connected to the computer through a
network cable. If the problem persists, contact authorized local service
suppliers.
A.3
The CPE fails to search for the wireless network.

Check that the power adapter is connected properly.

Check that the CPE is placed in an open area that is far away from
obstructions, such as concrete or wooden walls.

Check that the CPE is placed far away from household electrical appliances
that generate strong electromagnetic field, such as microwave ovens,
refrigerators, and satellite dishes.
If the problem persists, contact authorized local service suppliers.
A.4
The power adapter of the CPE is overheated.

The CPE will be overheated after being used for a long time. Therefore,
power off the CPE when you are not using it.

Check that the CPE is properly ventilated and shielded from direct sunlight.
A.5

The parameters are restored to default values.
If the CPE powers off unexpectedly while being configured, the parameters
may be restored to the default settings.
After configuring the parameters, download the configuration file to quickly
restore the CPE to the desired settings
14
Appendix B Product List
Index
Content
EG7035 CPE
Picture
Amount
12V/1A adapter
PoE Combiner
Mounting bracket
User Manual
n/a
15
BaiCells EG7035 Bracket Installation Guide
V1.0
All rights reserved © BaiCells Technologies Co., Ltd.
Assemble Bracket
Install bracket and screw on, do
not tighten the screws.
Install ground wire and
lock the screw.
Tighten four screws using allen
hexagon wrench.
Put U shape screw on bracket of
lock wall and install it on CPE
bracket.
Screw on four bacaket srews.
Install on Pole
Loop U shape screw on pole
and put on pole bracket.
Adjust CPE to a suitble position.
Tighten four screws.
Tighten U shape screw nut
using wrench.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : Yes
Encryption                      : Standard V4.4 (128-bit)
User Access                     : Print, Extract, Print high-res
Author                          : admin
Create Date                     : 2016:06:21 14:13:18+08:00
Modify Date                     : 2016:06:22 13:58:34-07:00
Subject                         : V1.0
Language                        : zh-CN
Tagged PDF                      : No
XMP Toolkit                     : Adobe XMP Core 5.2-c001 63.139439, 2010/09/27-13:37:26
Format                          : application/pdf
Creator                         : admin
Description                     : V1.0
Title                           : BaiCells EG7035 User Manual
Creator Tool                    : Microsoft® Word 2010
Metadata Date                   : 2016:06:22 13:58:34-07:00
Producer                        : Microsoft® Word 2010
Document ID                     : uuid:2b932dc5-95e1-4f52-bc4c-1c23bcd43ca3
Instance ID                     : uuid:e1b08637-bc64-4f81-a03b-7121d32175a8
Page Count                      : 24

EXIF Metadata provided by EXIF.tools