BandRich 35M168 LTE/EVDO REV. A MODULE User Manual M535U User Guide 20140220
BandRich Inc. LTE/EVDO REV. A MODULE M535U User Guide 20140220
BandRich >
User Manual
M535U User Guide 1. Connect the evaluation board with USB to Data & Power. 2. Follow the direction to insert the SIM card. 3. Turn on the Power Switch. 4. Launch Putty and select Serial. 5. Launch Device Manager and check the AT CMD port. 6. Input the AT CMD port to Putty. 7. Input AT command (at$qcrmcall=1,1)to establish the connection between PC and M535U. 8. How to install M535U to other host devices. Insert the module to assigned standard PCI‐E mini card slot. Secure the module using two screws and attach the cables (LTE1/2 & GPS if applicable) appropriately. Manual Information to the End User The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the user’s manual of the end product which integrates this module. The end user manual shall include all required regulatory information/warning as show in this manual. Federal Communication Commission Interference Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: ‐ Reorient or relocate the receiving antenna. ‐ Increase the separation between the equipment and receiver. ‐ Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. ‐ Consult the dealer or an experienced radio/TV technician for help. Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This transmitter must not be co‐located or operating in conjunction with any other antenna or transmitter. Radiation Exposure Statement This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20 cm between the radiator & your body. End Product Labeling When the module is installed in the host device, the FCC ID label must be visible through a window on the final device or it must be visible when an access panel, door or cover is easily re‐moved. If not, a second label must be placed on the outside of the final device that contains the following text: “Contains FCC ID: UZI‐35M168” The grantee's FCC ID can be used only when all FCC compliance requirements are met. This device is intended only for OEM integrators under the following conditions: (1) The antenna must be installed such that 20 cm is maintained between the antenna and users, (2) The transmitter module may not be co‐located with any other transmitter or antenna, except has been assessed in accordance with FCC multi‐transmitter product guidelines. (3) To comply with FCC regulations limiting both maximum RF output power and human exposure to RF radiation, the maximum antenna gain including cable loss in a mobile exposure condition must not exceed: When in stand‐alone configuration: 。 9.0 dBi in Cellular band 。 8.0 dBi in PCS band 。 7.5 dBi in AWS band 。 11.0 dBi in 700 MHz band When co‐located with a 5 dBi Wi‐Fi antenna: 。 6.0 dBi in Cellular band 。 8.0 dBi in PCS band 。 7.5 dBi in AWS band 。 7.5 dBi in 700 MHz band In the event that these conditions cannot be met (for example certain laptop configurations or co‐location with another transmitter), then the FCC authorization is no longer considered valid and the FCC ID cannot be used on the final product. In these circumstances, the OEM integrator will be responsible for re‐evaluating the end product (including the transmitter) and obtaining a separate FCC authorization.
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.6 Linearized : Yes Encryption : Standard V4.4 (128-bit) User Access : Print, Extract, Print high-res Author : sandy Create Date : 2014:02:20 16:44:43+08:00 Modify Date : 2014:02:26 17:26:37+08:00 XMP Toolkit : Adobe XMP Core 4.2.1-c043 52.372728, 2009/01/18-15:08:04 Format : application/pdf Creator : sandy Title : Microsoft Word - M535U User Guide 20140220 Creator Tool : PScript5.dll Version 5.2.2 Metadata Date : 2014:02:26 17:26:37+08:00 Producer : Acrobat Distiller 10.0.0 (Windows) Document ID : uuid:3e38d906-2d13-42a3-9c52-8f2b1b654f59 Instance ID : uuid:4cedbf3e-aa25-4e21-9592-d89ce8a67c65 Page Count : 5EXIF Metadata provided by EXIF.tools