BandRich M280 M280 HSUPA Half Mini Card Module User Manual BandRich M280 UMTS Module Ver 03

Download:
Mirror Download [FCC.gov]
Document ID	1075777
Application ID	QX38lQVDSli10jC4rQSi5A==
Document Description	BandRich M280 UMTS Module User Manual Ver 03
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	30.84kB (385505 bits)
Date Submitted	2009-03-04 00:00:00
Date Available	2009-03-05 00:00:00
Creation Date	2009-03-03 10:32:00
Producing Software	Acrobat Distiller 8.1.0 (Windows)
Document Lastmod	2009-03-03 10:32:00
Document Title	Microsoft Word - BandRich_M280_UMTS Module_User Manual_Howard_update.doc
Document Creator	PScript5.dll Version 5.2
Document Author:	howard_liang

®
BandLuxe M280 Series HSUPA Module
User Manual
Class:
User Manual
Doc. No.:
M280-D-001
Doc. Version:
1.0
Publish Date:
2008-Nov-06
THE SPECIFICATIONS AND INFORMATION REGARDING THE PRODUCTS IN THIS MANUAL ARE SUBJECT
TO CHANGE WITHOUT NOTICE. ALL STATEMENTS, INFORMATION, AND RECOMMENDATIONS IN THIS
MANUAL ARE BELIEVED TO BE ACCURATE BUT ARE PRESENTED WITHOUT WARRANTY OF ANY KIND,
EXPRESS OR IMPLIED. USERS MUST TAKE FULL RESPONSIBILITY FOR THEIR APPLICATION OF ANY
PRODUCTS.
THE SOFTWARE LICENSE AND LIMITED WARRANTY FOR THE ACCOMPANYING PRODUCT ARE SET
FORTH IN THE INFORMATION PACKET THAT SHIPPED WITH THE PRODUCT AND ARE INCORPORATED
HEREIN BY THIS REFERENCE.
NOTWITHSTANDING ANY OTHER WARRANTY HEREIN, ALL DOCUMENT FILES AND SOFTWARE OF
THESE SUPPLIERS ARE PROVIDED “AS IS” WITH ALL FAULTS. PRODUCT AND THE ABOVE-NAMED
SUPPLIERS DISCLAIM ALL WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING, WITHOUT LIMITATION,
THOSE OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT OR
ARISING FROM A COURSE OF DEALING, USAGE, OR TRADE PRACTICE.
IN NO EVENT SHALL PRODUCT OR ITS SUPPLIERS BE LIABLE FOR ANY INDIRECT, SPECIAL,
CONSEQUENTIAL, OR INCIDENTAL DAMAGES, INCLUDING, WITHOUT LIMITATION, LOST PROFITS OR
LOSS OR DAMAGE TO DATA ARISING OUT OF THE USE OR INABILITY TO USE THIS MANUAL, EVEN IF
PRODUCT OR ITS SUPPLIERS HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
BandRich M280
Datasheet
Document Number: M280-D-001
BandRich Inc.
8F., No. 188, Baociao Rd., Sindian City
TAIPEI, TAIWAN, R.O.C.
http://www.bandrich.com
COPYRIGHT ©2007-2008 BandRich All rights reserved.
Table of Contents
Section 1
1.1
1.2
1.3
1.4
1.5
1.6
1.7
Introduction ............................................................................. 1
General Description .................................................................................................................. 1
Features .................................................................................................................................... 2
1.2.1 WCDMA ....................................................................................................................... 2
1.2.2 E-GPRS ....................................................................................................................... 2
1.2.3 Baseband Functionality................................................................................................ 2
1.2.4 Software Functionality.................................................................................................. 3
M280 HALF PCI-Express Mini Card Interface .......................................................................... 4
1.3.1 Pin Description ............................................................................................................. 4
1.3.2 Installation Instructions ................................................................................................ 5
Network LED indicate device .................................................................................................... 6
USB Interface............................................................................................................................ 7
USIM Interface .......................................................................................................................... 7
Antenna Guidelines and RF Connection .................................................................................. 8
1.7.1 Antenna specifications ................................................................................................. 8
1.7.2 Antenna connector....................................................................................................... 8
Section 2
Device Driver Interface ......................................................... 10
Section 3
AT Command Set Reference ................................................ 11
Section 4
Packing Information.............................................................. 16
Section 5
Federal Communications Commission (FCC) Statement.. 17
Section 1
1.1
Introduction
General Description
The M280 module series is HALF PCI Express Mini Card providing WWAN (HSUPA, HSDPA,
WCDMA, EGPRS, and GPS) connectivity to laptops or any other device equipped with a HALF PCI
Express Mini Card slot.
Figure 1-1
Top View
Figure 1-2
Bottom View
1.2
Features
1.2.1
WCDMA
1.2.2
E-GPRS
1.2.3
FDD 850/1900/2100 MHz
Power Class 3 (+24dBm)
WCDMA 384/384 kbps downlink/uplink modem operation
HSUPA 2Mbps uplink modem operation (SW upgradable to 5.7Mbps)
HSDPA 7.2Mbps downlink modem operation
Supports UL and DL Compressed Modes
Supports Circuit and Packet-Switched Data
M280V supports 3G voice call via PCM interface
The UMTS 2100 is only use in Europe and not available for America
850/900/1800/1900 MHz
GSM Power Class 4 (2W) for 850/900 bands
GSM Power Class 1 (1W) for 1800/1900 bands
EDGE class E2 (+27 dBm in 850/900 bands, +26 dBm in 1800/1900 bands)
GPRS/EGPRS Multislot Class 12 (4 slots Rx, 4 slots Tx, 5 slots active max)
GPRS/EGPRS Class B Type 1 MT
GPRS CS1-CS4; EGPRS MCS1-MCS9
Circuit Switched Data: 14.4 and 9.6 kbps
M280V supports GSM voice call via PCM interface
Baseband Functionality
The M280 module interfaces with host device through HALF PCI Express Mini Card interface. The
interface equips with USB2.0 interface, USIM interface, LED control signal, Wake# signal to request
host device return from sleep/suspended state, and W_Disable# signal to disable radio operation.
There are several GPIO pins (2.6V compatible) reserved for customized applications, please contact
BandRich for discussion. Besides the above mentioned interfaces, M280V also provides PCM
interfaces reserved for voice applications. The M280-LC features low power consumption but
requires higher input voltage than HALF PCI standard.
1.2.4
Software Functionality
M280 module series is supplied with device driver of Microsoft Windows Vista 32/64, Windows XP
SP2 above, Windows 2000 SP4 above, Mac OSX 10.4 above, and Linux Fedora 8, Unbuntu 7, Open
SuSE 10.
1.3
M280 HALF PCI-Express Mini Card Interface
1.3.1
Table 1-1
Pin Description
M280 Module Series Connector Pin-out
Pin No.
Name
Pin No.
Name
WAKE#/GPIO1 (optional)
Vaux
PCM_DOUT (M280V only)
GND
PCM_DIN (M280V only)
N.C./GPIO2 (optional)
N.C.
UIM_PWR
GND
10
UIM_DATA
11
PCM_SYNC (M280V only)
12
UIM_CLK
13
PCM_CLK (M280V only)
14
UIM_RESET
15
GND
16
N.C.
17
N.C.
18
GND
19
N.C.
20
W_DISABLE#
21
GND
22
HW_RST#
23
N.C./GPIO3 (optional)
24
Vaux
25
N.C.
26
GND
27
GND
28
N.C.
29
GND
30
N.C.
31
N.C.
32
N.C.
33
N.C.
34
GND
35
GND
36
USB_D-
37
GND
38
USB_D+
39
Vaux
40
GND
41
Vaux
42
LED_WWAN# *
43
GND
44
N.C.
45
N.C.
46
N. C.
47
N.C.
48
N.C.
49
N.C.
50
GND
51
N.C.
52
Vaux
For more information, please refer to HALF PCI-SIG, HALF PCI Express Mini Card
Electromechanical Specification 1.2. http://www.half PCIsig.com/home
1.3.2
Installation Instructions
IF you want to insert the module into the connector, make sure the power is OFF and follow the steps
as below:
a.
Insert the module into the connector at the angle of 20 degrees.
b.
Firmly insert the module into the connector, and press the module down into the securing clips
until the card clicks into place.
Figure 1-3
Installation Figure
Diversity
Main
After inserting the module into the connector, you can connect the antenna with the module. The main
antenna is on the right side and the diversity antenna (RX only) is on the left side.
Please keep the antenna more than 20cm away from all persons.
1.4
Network LED indicate device
The Network LED indicated device is ground-referenced current sink. The host drives the device to
provide a current path and an appropriate voltage for LED at PIN 42 of M280 module. Figure 2-2
shows the block diagram of the current drivers. Table 2-3 describes the LED output characteristics in
different states.
Figure 1-4
LED Current Driver Example
Table 1-2 LED Output
LED State
Module Status Description
LED Characteristics
OFF
Module is not powered.
LED is OFF.
ON
Module is powered and camped on
network, but not transmitting or receiving.
LED is continuously ON.
Slow blink
Module is powered and searching for
network (not yet registered on network).
LED is flashing at a steady slow
speed.
250ms±5% ON period and
750ms±5% OFF period
Intermittent
blink
LED is flashing intermittently
during data transfer activity.
Module is transmitting or receiving
50ms±5% ON period and
250ms±5% OFF period
1.5
USB Interface
M280, M280V and M280-LC module are compliant with USB2.0 in all three modes (Low speed, Full
speed, and high speed). When two devices are connected via a USB interface, one of the devices must
act as a host, and the other device must act as a peripheral. The host is responsible for initiating and
controlling traffic on the bus. For example, the USB specification requires PCs to act as hosts, and
other devices such as M280 to act as devices.
Figure 1-5
1.6
USB Interface
USIM Interface
The universal subscriber identification module (USIM) is a smart card for UMTS/GSM cellular
applications. The USIM provides the required subscription information to allow the mobile equipment
to attach to a GSM or UMTS network. The USIM also provides the subscriber's verification
procedures as well as authentication methods for network authentication during the network
registration procedures. Upon power-up or after a soft-reset, the clock and data lines to the USIM will
be active through the initialization process. Figure 2-3 shows the SIM card pin definition. It’s
recommended to implement hardware USIM detection mechanism or complete avoiding USIM
hot-plug through mechanical design. The reference design for hardware USIM detection is provided
in the “Application Note for BandLuxe Module USIM Detection Recommendation”.
Table 1-3
SIM Card Pin Definition
Pin No.
Description
Vcc
RST
CLK
GND
Vpp
I/O
y
1.7
USIM_CLK and USIM_RST signal, include 33pF filter capacitors is required to be placed near
the SIM connector.
Route all USIM signals carefully – isolate them from sensitive analog and RF signals.
External ESD diodes are necessary to protect the chip on the module; the ESD diodes should be
placed near the connector.
Refer to the reference circuits below:
Antenna Guidelines and RF Connection
This section describes general guidelines for the design of multi-band antenna required for the M280
module series.
1.7.1
Antenna specifications
Frequency range
GSM850 (824-894 MHz)
EGSM900 (880-960 MHz)
DCS1800 (1710-1880 MHz)
PCS1900 (1850-1990 MHz)
WCDMA 850/1900/2100 (824-894 / 1850-1990 / 1920-2170 MHz)
The UMTS 2100 is only use in Europe and not available for America
Gain
Radiation pattern: omni-directional
Gain averaged in space in all frequencies: > -3dBm
Gain for Diversity Antenna
1.
Within 3 dB comparing to gain of primary antenna recommended
2.
No worse than 6 dB of gain of primary antenna
Maximum VSWR
< 2.5:1 with 50 reference impedance
Polarization
Linear
1.7.2
Antenna connector
The antenna connector type used is a U.FL microwave coaxial connector. It is also can be used for
testing purpose.
Figure 1-6
Antenna Connector Position and Type
Main Antenna
Connector
Diversity Antenna
Connector
Section 2
Device Driver Interface
Basically the module will manifest itself as a composite USB device which creates stubs which the
other higher level drivers hook into and provide their respective function. The composite USB device
could be modem, NDIS interface, AT command interface or diagnostics interface. All device drivers
used by OS have been created for Microsoft Windows Vista 32/64, Windows XP SP2 above, Windows
2000 SP4 above, Mac OSX 10.4 above, and Linux Fedora 8, Unbuntu 7, Open SuSE 10.
Either the modem or the NDIS interface can be used to transfer data; and AT command interface or
diagnostic interface could be used to send/receive information of the module via the Connection
Manager (CM) application. For more information about supporting AT commands please refer to
section 4.
10
Section 3
AT Command Set Reference
For the description of BandLuxe AT Command API, please refer to Table 3-1 for reference.
Table 3-1
Abbreviations and Acronyms Table
BandLuxe HSPA Modem AT Command Interface API
Serial Port Name: BandLuxe AT CMD Interface
AT Command
Command description
Command Format
AT&F
Set all current parameters to manufacturer defaults
AT&F[]
AT&V
Display current configuration
AT&V[]
ATE
Enable command echo
ATE
ATI
Display product identification information
ATI
ATQ
Set result code presentation mode
ATQ[]
ATV
Set result code format mode
ATV[]
ATZ
Set all current parameters to user defined profile
ATZ[]
ATS3
Write command line termination character
ATS4
Set response formatting character
ATS5
Write command line editing character
AT+GMI
Request manufacturer identification
S3=
S3?
S3=?
S4=
S4?
S4=?
S5=
S5?
S5=?
AT+GMI
AT+GMM
Request model identification
AT+GMM
AT+GMR
Request revision identification of software status
AT+GMR
AT+GSN
Request serial number identification
AT+GSN
AT+GCAP
Request complete TA capabilities list
AT+CBST
Select bearer service type
AT+GCAP
AT+GCAP?
AT+CBST=[[, [, ]]]
AT+CBST?
AT+CBST=?
AT+CRLP
Select radio link protocol param
AT+CRLP=[[, [, [, ]]]]
AT+CRLP?
AT+CRLP=?
AT+CREG
Network registration
AT+CREG=[]
AT+CREG?
AT+CREG=?
AT+CGREG
GPRS network registration status
AT+CGREG=[]
AT+CGREG?
AT+CGREG=?
AT Command
Command description
Command Format
AT+CFUN
Full functionality mode
AT+CFUN=[,]
AT+CFUN?
AT+CFUN=?
AT+GCAP
Request complete TA capabilities
list
AT+GCAP
AT+GCAP=?
AT+CSCS
Used Character Set
AT+CSCS=[]
AT+CSCS?
AT+CSCS=?
AT+CEER
AT+CMEE
Cause Location ID for the extended AT+CEER
error report
Report Mobile Terminal Error
AT+CMEE=[]
AT+CMEE?
AT+CMEE=?
AT+CGDCONT
Define PDP Context
AT+CGDCONT=[ [, [,
[, [, ,]]]]]]
AT+CGDCONT?
AT+CGDCONT=?
AT+CGDSCONT Define Secondary PDP Context
AT+CGDSCONT=[,[,[,]]]
AT+CGDSCONT?
AT+CGDSCONT=?
AT+CGTFT
Traffic Flow Template
AT+CGTFT=[, [,

[,
[,
[, [,
[,
[,
[, ]]]]]]]]]
AT+CGTFT?
AT+CGTFT=?
AT+CGEQREQ
3G Quality of Service Profile
(Requested)
AT+CGEQREQ=[ [,
[,
[,
[,
[,
[,
[,
[,
[,
[,
[,
[,
[,
[,]]]]]]]]]]]]]]]
AT+CGEQREQ?
AT+CGEQREQ=?
12
AT Command
Command description
Command Format
AT+CGEQMIN
3G Quality of Service Profile
(Minimum acceptable)
AT+CGEQMIN=[ [,
[,
[,
[,
[,
[,
[,
[,
[,
[,
[,
[,
[,
[,]]]]]]]]]]]]]]]
AT+CGEQMIN?
AT+CGEQMIN=?
AT+CGQREQ
Quality of Service Profile
(Requested)
AT+CGQREQ=[[,[,[,
[,[,]]]]]]
AT+CGQREQ?
AT+CGQREQ=?
AT+CGQMIN
Quality of Service Profile (Minimum AT+CGQMIN=[[,[,[,
acceptable)
[,[,]]]]]]
AT+CGQMIN?
AT+CGQMIN=?
AT+CGEREP
Subscriber number
AT+CGEREP=[[,]]
AT+CGEREP?
AT+CGEREP=?
AT+CGPADDR
Show PDP address
AT+CGPADDR=[ [, [,…]]]
AT+CGPADDR=?
AT+CGCLASS
GPRS mobile station class
AT+CGCLASS= []
AT+CGCLASS?
AT+CGCLASS=?
AT+CGSMS
Select service for MO SMS
messages
AT+CGSMS=[]
AT+CGSMS?
AT+CGSMS=?
AT+CSMS
Select Message Service
AT+CSMS=
AT+CSMS?
AT+CSMS=?
AT+CMGF
Select SMS message format
AT+CMGF=[]
AT+CMGF?
AT+CMGF=?
AT+CSCA
Service Centrer Address
AT+CSCA=[,]
AT+CSCA?
AT+CSCA=?
AT+CSMP
Set SMS text mode parameters
AT+CSDH
Show SMS text mode parameters
13
AT+CSDH=[]
AT+CSDH?
AT+CSDH=?
AT Command
Command description
Command Format
AT+CSQ
Request signal strength
AT+CSQ
AT+CSQ=?
AT+CPIN
Check PIN Status
AT+CPIN=[,]
AT+CPIN?
AT+CPIN=?
AT+CGATT
PS attach / detach
AT+CGATT= []
AT+CGATT?
AT+CGATT=?
AT+CGACT
PDP context activate or deactivate AT+CGACT=[ [,[,[,…]]]]
AT+CGACT?
AT+CGACT=?
AT+CGCMOD
PDP Context Modify
AT+CPBS
Select phone book memory storage AT+CPBS=
AT+CPBS?
AT+CPBS=?
AT+CPBR
Read Phonebook Memory entries
AT+CPBR=[,]
AT+CPBR?
AT+CPBF
Find Phonebook Memory entries
AT+CPBF=
AT+CPBF=?
AT+CPBW
Write phone book entry
AT+CPBW=[][,[,[,]]]
AT+CPBW=?
AT+CPMS
Preferred Message Storage
AT+CPMS=[, [,]]
AT+CPMS?
AT+CPMS=?
AT+CNMI
New Message Indications to TE
AT+CNMI=[[,[,[,[,]]]]]
AT+CNMI?
AT+CNMI=?
AT+CMGL
List Messages
AT+CMGL[=]
AT+CMGL=?
AT+CMGR
Read Message
AT+CMGR=
AT+CMGR=?
AT+CMGS
Send SMS message
AT+CMGS=[,]
AT+CMGS=?
AT+CMGD
Delete SMS message
AT+CMGD=
AT+CMGD=?
AT+CNMA
New SMS message acknowledge
to ME/TE
AT+CNMA
AT+CNMA=?
AT+COPS
Operator selection
AT+COPS[=[, [, ]]]
AT+COPS?
AT+COPS=?
AT+CLCK
Facility lock
AT+CLCK=,[,[,]]
AT+CLCK=?
AT+CGCMOD=[[,[,…]]]
AT+CGCMOD=?
14
AT Command
Command description
Command Format
AT+CPWD
Change password
AT+CPWD=,,
AT+CPWD=?
AT+CUSD
Unstructured supplementary
service data
AT+CUSD=[[,[,]]]
AT+CUSD?
AT+CUSD=?
AT+CIMI
Read IMSI
AT+CIMI
AT+CIMI=?
AT+CGMI
Request manufacturer identification AT+CGMI
AT+CGMM
Request model identification
AT+CGMM
AT+CGMR
Request revision identification
AT+CGMR
AT+CGSN
AT+CGSN
AT+CNUM
Request product serial number
identification
Subscriber number
AT+CSIM
Generic SIM access
+COLP=[]
AT+CRSM
Restricted SIM access
AT+CRSM=[,[,,,[,]]]
AT+CRSM=?
AT+COPN
Read operator names
AT+COPN
AT+COPN=?
AT+CPOL
Preferred PLMN list
AT+CPOL=[][,[,]]
AT+CPOL?
AT+CPOL=?
AT+CPLS
Selection of preferred PLMN list
AT+CPLS=
AT+CPLS?
AT+CPLS=?
AT+CTZR
Time Zone Reporting
AT+CTZR=
AT+CTZR?
AT+CTZR=?
The retries count of PIN1, PIN2,
PUK1 or PUK2
AT+CPINC
AT+CPINC=?
AT+CPINC
15
AT+CNUM
AT+CNUM=?
Section 4
Packing Information
For the information about packing of shipment, packing material, and storage environment
recommendation, please refers to “BandLuxe Module Packing and Storage Recommendation”.
16
Section 5
Federal Communications Commission (FCC)
Statement
You are cautioned that changes or modifications not expressly approved by the part
responsible for compliance could void the user’s authority to operate the equipment.
15.105(b)
Federal Communications Commission (FCC) Statement
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the following
measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
-Consult the dealer or an experienced radio/TV technician for help.
Operation is subject to the following two conditions:
1) this device may not cause interference and
2) this device must accept any interference, including interference that may cause undesired
operation of the device.
FCC RF Radiation Exposure Statement:
1. This Transmitter must not be co-located or operating in conjunction with any other antenna or
transmitter.
2. This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with a minimum distance of 20
centimeters between the radiator and your body.
Note: The end product shall has the words “Contains Transmitter Module
FCC ID: UZI-M280
This device complies with part 15 of the FCC Rules. Operation is subject to the condition that this
device does not cause harmful interference.
17
『減少電磁波，請妥善使用』

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
XMP Toolkit                     : Adobe XMP Core 4.0-c316 44.253921, Sun Oct 01 2006 17:14:39
Producer                        : Acrobat Distiller 8.1.0 (Windows)
Creator Tool                    : PScript5.dll Version 5.2
Modify Date                     : 2009:03:03 10:32+08:00
Create Date                     : 2009:03:03 10:32+08:00
Format                          : application/pdf
Title                           : Microsoft Word - BandRich_M280_UMTS Module_User Manual_Howard_update.doc
Creator                         : howard_liang
Document ID                     : uuid:fc81ccd9-2c50-41a4-bc79-ebd22342015a
Instance ID                     : uuid:c437fce9-a4b6-428a-9f3b-a9085e50106a
Page Count                      : 21
Author                          : howard_liang

EXIF Metadata provided by EXIF.tools