User Manual.pdf
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 2051585 |
| Application ID | tBLlMqlBzFsBWmsLV6zFiA== |
| Document Description | User Manual.pdf |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 6.5kB (81270 bits) |
| Date Submitted | 2013-08-22 00:00:00 |
| Date Available | 2014-02-18 00:00:00 |
| Creation Date | 2013-08-16 16:00:44 |
| Producing Software | Acrobat Distiller 10.0.0 (Windows) |
| Document Lastmod | 2013-08-16 17:11:50 |
| Document Title | Microsoft Word - M530S User Manual for FCC_0715_0816v2 |
| Document Creator | PScript5.dll Version 5.2.2 |
| Document Author: | sandy |
User Manual BandLuxe M530S LTE/EVDO Module Introduction Thank you for your purchase of the M530S LTE/EVDO Module. This device is designed to access the Internet via 4G technology. Features LTE/EVDO Uplink speeds up to 50 Mbps Downlink speeds up to 100 Mbps Operating Frequency Bands o LTE: Band 25/26/41 o EVDO: BC0/BC1/BC10 Getting Started Getting Started This chapter will provide a hardware overview of the M530S LTE/EVDO Module. The module is operated with defined voltage and pin assignments according to the specification in the next page. Package Contents 1. 1. M530S LTE/EVDO Module 1. 1. Getting Started Specifications Note: Specifications are subject to change without notice. Form Factor Dimension (LxWxH, mm) Weight (g) Chipset Connectivity and Data Speed LTE Band LTE Data Rate 3GPP Protocol Support CDMA 1xRTT/EV-DO EVDO version eHRPD Location solution Antenna port RF Antenna Port LTE MIMO EVDO/CDMA Diversity Support GPS RF Antenna Connector Type Interface USB SIM Connector UART LED Control GPIOs Power Info Voltage Power consumption Power save mode Environment Operation Temperature Storage Temperature Operating System supported PCI Express Mini Card 50.95 x 36 x 3.9 mm 10.6 g Qualcomm MDM9615 FDD: B25/B26, TDD: B41 FDD: Downlink up to 100Mbps, Uplink up to 50Mbps TDD: Downlink up to 68Mbps, Uplink up to 17Mbps (in configuration 3) Release 9, UE Category 3 BC0/BC1/BC10 Rev. 0, Rev. A Yes Standalone GPS, A-GPS, GPS XTRA, Composite Glonass and GPS GNSS systems Main, Aux and GNSS B25/B26/B41, DL 2x2 SU-MIMO Yes Yes, Supports Passive GPS antenna IPEX 20279 USB 2.0 HS Interface to SIM Connector as PIN assignment. Yes Yes, x 3 PINs for LED control signal Yes, these pins can be optionally configured for UIM, SPI, I2C, or LED use. 3.7 V typical, 3.5V ~ 4.2V voltage swing Max. 3.5W in worst conditions, Typical 2W Supported and with 28nm Qualcomm Chipset for lower power consumption. -30oC to 60oC -30oC to 85oC Linux, MAC OS X, Windows Other Supporting Features AT Commands OMA-DM FW Upgrade Support Yes Yes, OMA-DM is an optional feature Yes, support FW upgrade by DM platform or proprietary auto-checking method Certifications GCF, CCF, FCC, ALU IOT, Ericsson IOT, Samsung IOT, Sprint certification Conformance of Environmental Regulation Environmental Regulation RoHS Getting Started Federal Communication Commission Interference Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. Getting Started This device is intended only for OEM integrators under the following conditions: 1. 2. The antenna must be installed such that 20 cm is maintained between the antenna and users, and The transmitter module may not be co-located with any other transmitter or antenna. As long as 2 conditions above are met, further transmitter test will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed IMPORTANT NOTE: In the event that these conditions can not be met (for example certain laptop configurations or co-location with another transmitter), then the FCC authorization is no longer considered valid and the FCC ID can not be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate FCC authorization. End Product Labeling This transmitter module is authorized only for use in device where the antenna may be installed such that 20 cm may be maintained between the antenna and users. The final end product must be labeled in a visible area with the following: “Contains FCC ID: UZI-M30S58”. The grantee's FCC ID can be used only when all FCC compliance requirements are met. Manual Information To the End User The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the user’s manual of the end product which integrates this module. The end user manual shall include all required regulatory information/warning as show in this manual.
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.6 Linearized : Yes Encryption : Standard V2.3 (128-bit) User Access : Print, Annotate, Fill forms XMP Toolkit : Adobe XMP Core 4.0-c316 44.253921, Sun Oct 01 2006 17:14:39 Create Date : 2013:08:16 16:00:44+08:00 Creator Tool : PScript5.dll Version 5.2.2 Modify Date : 2013:08:16 17:11:50+08:00 Metadata Date : 2013:08:16 17:11:50+08:00 Producer : Acrobat Distiller 10.0.0 (Windows) Format : application/pdf Title : Microsoft Word - M530S User Manual for FCC_0715_0816v2 Creator : sandy Document ID : uuid:21cd4899-c3af-41ad-814a-8ae07548ccf2 Instance ID : uuid:972518e9-55df-44ff-a763-ab43c0c0def7 Page Count : 7 Author : sandyEXIF Metadata provided by EXIF.tools