Barco PFWX 51B & PFWU User Manual To The 5dc9e0a7 A1de 4554 9288 071287fc8dc3
User Manual: Barco PFWX-51B & PFWU-51B to the manual
Open the PDF directly: View PDF .
Page Count: 82
Download | ![]() |
Open PDF In Browser | View PDF |
PFWX-51B & PFWU-51B 8VHUPDQXDO Barco nv Projection Division Noordlaan 5, B-8520 Kuurne Phone: +32 56.36.82.11 Fax: +32 56.36.883.86 Support: www.barco.com/esupport Visit us at the web: www.barco.com Printed in China Revision: 03 Changes Barco provides this manual ’as is’ without warranty of any kind, either expressed or implied, including but not limited to the implied warranties or merchantability and fitness for a particular purpose. Barco may make improvements and/or changes to the product(s) and/or the program(s) described in this publication at any time without notice. This publication could contain technical inaccuracies or typographical errors. Changes are periodically made to the information in this publication; these changes are incorporated in new editions of this publication. The latest edition of Barco manuals can be downloaded from the Barco web site www.barco.com or from the secured Barco web site https://my.barco.com. Copyright © All rights reserved. No part of this document may be copied, reproduced or translated. It shall not otherwise be recorded, transmitted or stored in a retrieval system without the prior written consent of Barco. EN55022/CISPR22 Class A ITE (Information Technology Equipment) Class A ITE is a category of all other ITE which satisfies the class A ITE limits but not the class B ITE limits. Such equipment should not be restricted in its sale but the following warning shall be included in the instructions for use: Warning : This is a class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures. Federal Communications Commission (FCC Statement) This equipment has been tested and found to comply with the limits for a class A digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area may cause harmful interference, in which case the user will be responsible for correcting any interference at his own expense. Guarantee and Compensation Barco provides a guarantee relating to perfect manufacturing as part of the legally stipulated terms of guarantee. On receipt, the purchaser must immediately inspect all delivered goods for damage incurred during transport, as well as for material and manufacturing faults Barco must be informed immediately in writing of any complaints. The period of guarantee begins on the date of transfer of risks, in the case of special systems and software on the date of commissioning, at latest 30 days after the transfer of risks. In the event of justified notice of complaint, Barco can repair the fault or provide a replacement at its own discretion within an appropriate period. If this measure proves to be impossible or unsuccessful, the purchaser can demand a reduction in the purchase price or cancellation of the contract. All other claims, in particular those relating to compensation for direct or indirect damage, and also damage attributed to the operation of software as well as to other services provided by Barco, being a component of the system or independent service, will be deemed invalid provided the damage is not proven to be attributed to the absence of properties guaranteed in writing or due to the intent or gross negligence or part of Barco. If the purchaser or a third party carries out modifications or repairs on goods delivered by Barco, or if the goods are handled incorrectly, in particular if the systems are commissioned operated incorrectly or if, after the transfer of risks, the goods are subject to influences not agreed upon in the contract, all guarantee claims of the purchaser will be rendered invalid. Not included in the guarantee coverage are system failures which are attributed to programs or special electronic circuitry provided by the purchaser, e.g. interfaces. Normal wear as well as normal maintenance are not subject to the guarantee provided by Barco either. The environmental conditions as well as the servicing and maintenance regulations specified in the this manual must be complied with by the customer. Trademarks Brand and product names mentioned in this manual may be trademarks, registered trademarks or copyrights of their respective holders. All brand and product names mentioned in this manual serve as comments or examples and are not to be understood as advertising for the products or their manufacturers. TABLE OF CONTENTS 1. SAFETY 1 1.1 General considerations 1 1.2 Important safety instructions 2 2. GENERAL 5 2.1 Installation requirements 5 2.2 Unpacking the projector 6 2.3 Initial inspection 7 2.4 Projector configurations 8 2.5 Projector air inlets and outlets 10 2.6 Installation process overview 11 3. PHYSICAL INSTALLATION 12 3.1 Remote control unit (RCU) 12 3.2 Lenses 14 3.3 Connecting the projector with the power net 18 3.4 Alignment of a table mounted projector 19 3.5 Mounting the Ceiling mount 21 4. PROJECTOR PARTS AND FUNCTIONS 22 4.1 Projector front view 22 4.2 Projector Rear view 22 4.3 Input and Communication 23 4.4 Status lights of LED 26 4.5 Opening the I/O cover 27 4.6 Connecting the projector to other devices 28 5. GETTING STARTED 33 5.1 RCU & Local keypad 33 5.2 Remote Control and OSD Lite on Screen 33 5.3 Power on projector 34 5.4 Power off projector 35 5.5 Range of effective remote control signal reception 35 5.6 Source selection 35 TABLE OF CONTENTS 5.7 Changing OSD language 36 5.8 Adjusting the lens by horizontal and vertical lens shift 36 5.9 Introduction the OSD Lite on screen 37 6. ADVANCED OSD MENU 38 6.1 How to activate the Advanced OSD menu 38 6.2 How to navigate in the Advanced menu structure? 39 6.3 Advanced menu memory 39 7. IMAGE 40 7.1 Image menu overview 40 7.2 Display Mode 41 7.3 Brightness 41 7.4 Contrast 41 7.5 Computer 42 7.6 Auto Image 43 7.7 Advanced 44 7.8 Input Balance 45 8. SETTINGS 1 48 8.1 Settings 1 menu overview 48 8.2 Source 49 8.3 Projection 49 8.4 Aspect Ratio 50 8.5 Keystone 52 8.6 Digital Zoom 52 8.7 Advanced 1 52 8.8 Advanced 2 53 9. SETTINGS 2 54 9.1 Settings 2 menu overview 54 9.2 Auto Source 55 9.3 No Signal Power Off 56 9.4 Auto Power On 56 9.5 Lamp Mode 56 TABLE OF CONTENTS 9.6 Reset All 56 9.7 Status 56 9.8 Advanced 1 57 9.9 Advanced 2 59 10. MAINTENANCE 60 10.1 Lamp Replacement 60 10.2 Clean the dust 62 10.3 Cleaning the lens 62 10.4 Cleaning the exterior of the projector 62 10.5 Simple troubleshooting 63 11. PROJECTOR SPECIFICATION 65 11.1 PFWU-51B Specifications 65 11.2 PFWX-51B Specifications 67 11.3 Standard Source Files 69 11.4 Dimension 72 12. ENVIRONMENTAL INFORMATION 73 12.1 Disposal information 73 12.2 Rohs compliance 73 12.3 Production address 75 1.Safety 1. SAFETY About this chapter Read this chapter attentively. It contains important information to prevent personal injury while installing and using a PFWX-51B/PFWU-51B projector. Furthermore, it includes several cautions to prevent damage to the PFWX-51B/PFWU-51B projector. Ensure that you understand and follow all safety guidelines, safety instructions and warnings mentioned in this chapter before installing your PFWX-51B/PFWU-51B projector. After this chapter, additional “warnings” and “cautions” are given depending on the installation procedure. Read and follow these “warnings” and “cautions” as well. 1.1 General considerations When referring in this document to the term “PRESENT SERIES” means that the content is applicable for following Barco products: • PFWX-51B • PFWU-51B WARNING: Ensure you understand and follow all the safety guidelines, safety instructions, warnings and cautions mentioned in this manual. WARNING: Be aware of suspended loads. WARNING: Wear a hard hat to reduce the risk of personal injury. WARNING: Be careful while working with heavy loads. WARNING: Mind your fingers while working with heavy loads. CAUTION: High pressure lamp may explode if improperly handled. General safety instructions • Before operating this equipment please read this manual thoroughly and retain it for future reference. • Installation and preliminary adjustments should be performed by qualified Barco personnel or by authorized Barco service dealers. • All warnings on the projector and in the documentation manuals should be adhered to. • All instructions for operating and use of this equipment must be followed precisely. • All local installation codes should be adhered to. Notice on safety This equipment is built in accordance with the requirements of the international safety standards IEC60950-1, EN60950-1, UL60950-1 and CAN/CSA C22.2 No.60950-1, which are the safety standards of information technology equipment including electrical business equipment. These safety standards impose important requirements on the use of safety critical components, materials and insulation, in order to protect the user or operator against risk of electric shock and energy hazard and having access to live parts. Safety standards also impose limits to the internal and external temperature rises, radiation levels, mechanical stability and strength, enclosure construction and protection against the risk of fire. Simulated single fault condition testing ensures the safety of the equipment to the user even when the equipment’s normal operation fails. PFWX-51B/PFWU-51B 10/02/2014 1 1.Safety Users definition Throughout this manual, the term SERVICE PERSONNEL refers to persons having appropriate technical training and experience necessary to be knowledgeable of potential hazards to which they are exposed (including, but not limited to HIGH VOLTAGE ELECTRIC and ELECTRONIC CIRCUITRY and HIGH BRIGHTNESS PROJECTORS) in performing a task, and of measures to minimize the potential risk to themselves or other persons. The term USER and OPERATOR refers to any person other than SERVICE PERSONNEL, AUTHORIZED to operate professional projection systems. A PFWX-51B/PFWU-51B projector is intended "FOR PROFESSIONAL USE ONLY" by AUTHORIZED PERSONNEL familiar with potential hazards associated with high voltage, high intensity light beams, ultraviolet exposure and high temperatures generated by the lamp and associated circuits. Only qualified SERVICE PERSONNEL, knowledgeable of such risks, are allowed to perform service functions inside the product enclosure. 1.2 Important safety instructions To prevent the risk of electrical shock • This product should be operated from a mono phase AC power source. • This apparatus must be grounded (earthed) via the supplied 3 conductor AC power cable. If none of the supplied power cables are the correct one, consult your dealer. If you are unable to insert the plug into the outlet, contact your electrician to replace your obsolete outlet. Do not defeat the purpose of the grounding-type plug. • Do not allow anything to rest on the power cord. Do not locate this product where persons will walk on the cord. To disconnect the cord, pull it out by the plug. Never pull the cord itself. • Use only the power cord supplied with your device. While appearing to be similar, other power cords have not been safety tested at the factory and may not be used to power the device. For a replacement power cord, contact your dealer. • Do not operate the projector with a damaged cord. Replace the cord.Do not operate the projector if the projector has been dropped or damaged until it has been examined and approved for operation by a qualified service technician. • Position the cord so that it will not be tripped over, pulled, or contact hot surfaces. • If an extension cord is necessary, a cord with a current rating at least equal to that of the projector should be used. A cord rated for less amperage than the projector may overheat. • Never push objects of any kind into this product through cabinet slots as they may touch dangerous voltage points or short out parts that could result in a risk of fire or electrical shock. • Do not expose this projector to rain or moisture. • Do not immerse or expose this projector in water or other liquids. • Do not spill liquid of any kind on this projector. • Should any liquid or solid object fall into the cabinet, unplug the set and have it checked by qualified service personnel before resuming operations. • Do not disassemble this projector, always take it to an authorized trained service person when service or repair work is required. • Do not use an accessory attachment which is not recommended by the manufacturer. • Lightning - For added protection for this video product during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet. This will prevent damage to the device due to lightning and AC power-line surges. To prevent personal injury • Isolate electrically before replacing the lamp or lamp house. Caution: Hot lamp (house). • Caution: High pressure lamp may explode if improperly handled. Refer servicing to qualified service personnel. • To prevent injury and physical damage, always read this manual and all labels on the system before inserting the lamp casing, connecting to the wall outlet or adjusting the projector. • To prevent injury, take note of the weight of the projector. Minimum 2 persons are needed to carry the projector. • To prevent injury, ensure that the lens and all covers are correctly installed. See installation procedures. • Warning: high intensity light beam. NEVER look into the lens ! High luminance could result in damage to the eye. • Warning: extremely high brightness lamps: This projector uses extremely high brightness lamps. Never attempt to look directly into the lens or at the lamp. If the projection distance is less than 6 meter, any person needs to be at least 4 meters away from the projected image. Avoid close range reflection of the projected image on any reflecting surface (such as glass, metal, …) . When operating the projector, we strongly recommend wearing suitable safety glasses. • Before attempting to remove any of the projector’s covers, you must turn off the projector and disconnect from the wall outlet. • When required to switch off the projector, to access parts inside, always disconnect the power cord from the power net. • The power input at the projector side is considered as the disconnect device. When required to switch off the projector, to access parts inside, always disconnect the power cord at the projector side. In case the power input at the projector side is not accessible (e.g. ceiling mount), the socket outlet supplying the projector shall be installed nearby the projector and be easily accessible, or a readily accessible general disconnect device shall be incorporated in the fixed wiring. • Do not place this equipment on an unstable cart, stand, or table. The product may fall, causing serious damage to it and possible injury to the user. 2 PFWX-51B/PFWU-51B 10/02/2014 1.Safety • It is hazardous to operate without lens or shield. Lenses, shields or ultra violet screens shall be changed if they have become visibly damaged to such an extent that their effectiveness is impaired. For example by cracks or deep scratches. • Warning: Protection from ultraviolet radiation: Do not look directly in the light beam. The lamp contained in this product is an intense source of light and heat. One component of the light emitted from this lamp is ultraviolet light. Potential eye and skin hazards are present when the lamp is energized due to ultraviolet radiation. Avoid unnecessary exposure. Protect yourself and your employees by making them aware of the hazards and how to protect themselves. Protecting the skin can be accomplished by wearing tightly woven garments and gloves. Protecting the eyes from UV can be accomplished by wearing safety glasses that are designed to provide UV protection. In addition to the UV, the visible light from the lamp is intense and should also be considered when choosing protective eye wear. • Exposure to UV radiation: Some medications are known to make individuals extra sensitive to UV radiation. The American Conference of Governmental Industrial Hygienists (ACGIH) recommends occupational UV exposure for an-8 hour day to be less than 0,1 micro-watts per square centimeters of effective UV radiation. An evaluation of the workplace is advised to assure employees are not exposed to cumulative radiation levels exceeding these government guidelines. The exposer of this UV radiation is allowed for only 1 hour per day for maintenance and service persons. • Mercury Vapor Warnings: Keep the following warnings in mind when using the projector. The lamp used in the projector contains mercury. In case of a lamp rupture, explosion there will be a mercury vapor emission. In order to minimize the potential risk of inhaling mercury vapors: - Ensure the projector is installed only in ventilated rooms. - Replace the lamp module before the end of its operational life. - Promptly ventilate the room after a lamp rupture, explosion has occurred, evacuate the room (particularly in case of a pregnant woman). - Seek medical attention if unusual health conditions occur after a lamp rupture, explosion, such as headache, fatigue, shortness of breath, chest-tightening coughing or nausea. To prevent fire hazard • Do not place flammable or combustible materials near the projector! • Barco large screen projection products are designed and manufactured to meet the most stringent safety regulations. This projector radiates heat on its external surfaces and from ventilation ducts during normal operation, which is both normal and safe. Exposing flammable or combustible materials into close proximity of this projector could result in the spontaneous ignition of that material, resulting in a fire. For this reason, it is absolutely necessary to leave an “exclusion zone” around all external surfaces of the projector whereby no flammable or combustible materials are present. The exclusion zone must be not less than 50 cm (20”) for all DLP projectors. The exclusion zone on the lens side must be at least 5 m. Do not cover the projector or the lens with any material while the projector is in operation. Keep flammable and combustible materials away from the projector at all times. Mount the projector in a well ventilated area away from sources of ignition and out of direct sun light. Never expose the projector to rain or moisture. In the event of fire, use sand, CO2 or dry powder fire extinguishers. Never use water on an electrical fire. Always have service performed on this projector by authorized Barco service personnel. Always insist on genuine Barco replacement parts. Never use non-Barco replacement parts as they may degrade the safety of this projector. • Slots and openings in this equipment are provided for ventilation. To ensure reliable operation of the projector and to protect it from overheating, these openings must not be blocked or covered. The openings should never be blocked by placing the projector too close to walls, or other similar surface. This projector should never be placed near or over a radiator or heat register. This projector should not be placed in a built-in installation or enclosure unless proper ventilation is provided. • Projection rooms must be well ventilated or cooled in order to avoid build up of heat. • Let the projector cool down completely before storing. Remove cord from the projector when storing. • Heat sensitive materials should not be placed in the path of the exhausted air or on the lamp house. To prevent projector damage • This projector has been designed for use with a specific lamp (house) type. See installation instructions for its correct type. • The air filters of the projector must be cleaned or replaced on regular base (a "clean" booth would be monthly-minimum). Neglecting this could result in disrupting the air flow inside the projector, causing overheating. Overheating may lead to the projector shutting down during operation. • The projector must always be installed in a manner which ensures free flow of air into its air inlets and unimpeded evacuation of the hot air from its cooling system. • In order to ensure that correct airflow is maintained, and that the projector complies with Electromagnetic Compatibility (EMC)requirements, it should always be operated with all of it’s covers in place. • Slots and openings in the cabinet are provided for ventilation. To ensure reliable operation of the product and to protect it from overheating, these openings must not be blocked or covered. The openings should never be blocked by placing the product on a bed, sofa, rug, or other similar surface. This product should never be placed near or over a radiator or heat register. The device should not be placed in a built-in installation or enclosure unless proper ventilation is provided. • Ensure that nothing can be spilled on, or dropped inside the projector. If this does happen, switch off and unplug the mains supply immediately. Do not operate the projector again until it has been checked by qualified service personnel. • Do not block the projector cooling fans or free air movement around the projector. Loose papers or other objects may not be nearer to the projector than 30 cm (12") on any side. PFWX-51B/PFWU-51B 10/02/2014 3 1.Safety • Do not use this equipment near water. • Special care for Laser Beams:Special care should be used when DLP projectors are used in the same room as high power laser equipment. Direct or indirect hitting of a laser beam on to the lens can severely damage the Digital Mirror Devices™ in which case there is a loss of warranty. • Never place the projector in direct sun light. Sun light on the lens can severely damage the Digital Mirror Devices TM in which case there is a loss of warranty. • Save the original shipping carton and packing material. They will come in handy if you ever have to ship your equipment. For maximum protection, repack your set as it was originally packed at the factory. • Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning. Never use strong solvents, such as thinner or benzine, or abrasive cleaners, since these will damage the cabinet. Stubborn stains may be removed with a cloth lightly dampened with mild detergent solution. • To ensure the highest optical performance and resolution, the projection lenses are specially treated with an anti-reflective coating, therefore, avoid touching the lens. To remove dust on the lens, use a soft dry cloth. Do not use a damp cloth, detergent solution, or thinner. • Rated maximum ambient temperature, t a= 40 °C (104 °F). • The lamp house shall be replaced if it has become damaged or thermally deformed. On servicing • Do not attempt to service this product yourself, as opening or removing covers may expose you to dangerous voltage potentials and risk of electric shock. • Refer all servicing to qualified service personnel. • Attempts to alter the factory-set internal controls or to change other control settings not specially discussed in this manual can lead to permanent damage to the projector and cancellation of the warranty. • Unplug this product from the wall outlet and refer servicing to qualified service technicians under the following conditions: - When the power cord or plug is damaged or frayed. - If liquid has been spilled into the equipment. - If the product has been exposed to rain or water. - If the product does not operate normally when the operating instructions are followed. Adjust only those controls that are covered by the operating instructions since improper adjustment of the other controls may result in damage and will often require extensive work by a qualified technician to restore the product to normal operation. - If the product has been dropped or the cabinet has been damaged. - If the product exhibits a distinct change in performance, indicating a need for service. • Replacement parts: When replacement parts are required, be sure the service technician has used original Barco replacement parts or authorized replacement parts which have the same characteristics as the Barco original part. Unauthorized substitutions may result in degraded performance and reliability, fire, electric shock or other hazards. Unauthorized substitutions may void warranty. • Safety check: Upon completion of any service or repairs to this projector, ask the service technician to perform safety checks to determine that the product is in proper operating condition. • Possible explosion hazard: Always keep in mind the caution below: CAUTION: Do not touch a lamp during operation and right after it is turned off as it is extremely hot. Lamp contains mercury. It's brokeage might cause mercury or broken glass pieces to folow out of lamp housing. To avoid exposure the risk of mercury poisoning. Don't drop, hit, force or scratch while handing a lamp. To prevent battery explosion • Danger of explosion if battery is incorrectly installed. • Replace only with the same or equivalent type recommended by the manufacturer. • For disposal of used batteries, always consult federal, state, local and provincial hazardous waste disposal rules and regulations to ensure proper disposal. 4 PFWX-51B/PFWU-51B 10/02/2014 2.General 2. GENERAL About this chapter Read this chapter before installing your PFWX-51B/PFWU-51B projector. It contains important information concerning installation requirements for the PFWX-51B/PFWU-51B projector, such as minimum and maximum allowed ambient temperature, humidity conditions, required safety area around the installed projector, required power net, etc. Furthermore, careful consideration of things such as image size, ambient light level, projector placement and type of screen to use are critical to the optimum use of the projection system. Overview • • • • • • Installation requirements Unpacking the projector Initial inspection Projector configurations Projector air inlets and outlets Installation process overview WARNING: Barco provides a guarantee relating to perfect manufacturing as part of the legally stipulated terms of guarantee. Observing the specification mentioned in this chapter is critical for projector performance. Neglecting this can result in loss of warranty. 2.1 Installation requirements Environment conditions Table below summarizes the physical environment in which the PFWX-51B/PFWU-51B projector may be safely operated or stored. Environment Ambient Temperature Operating 5°C (41°F) to 35°C (95°F) Non-Operating -10°C (14°F) to 60°C (140°F) Humidity 10% to 85% RH Non-condensed 5% to 90% RH Non-Condensed Altitude -60 (-197Ft) to 3000m (9843Ft) -60 (-197Ft) to 10000m (32810Ft) Let the projector acclimatize after unpacking. Neglecting this may result in a startup failure of the Light Pro- cessor Unit. Cooling requirements The projector is fan cooled and must be installed with sufficient space around the projector head, minimum 30 cm (12 inch) to ensure sufficient air flow. It should be used in an area where the ambient temperature, as measured at the projector air inlet , does not exceed +35°C (+95°F). Clean air environment A projector must always be mounted in a manner which ensures the free flow of clean air into the projectors ventilation inlets. For installations in environments where the projector is subject to airborne contaminants such as that produced by smoke machines or similar (these deposit a thin layer of greasy residue upon the projectors internal optics and imaging electronic surfaces, degrading performance), then it is highly advisable and desirable to have this contamination removed prior to it reaching the projectors clean air supply. Devices or structures to extract or shield contaminated air well away from the projector are a prerequisite, if this is not a feasible solution then measures to relocate the projector to a clean air environment should be considered. Only ever use the manufacturer’s recommended cleaning kit which has been specifically designed for cleaning optical parts, never use industrial strength cleaners on the projector’s optics as these will degrade optical coatings and damage sensitive optoelectronics components. Failure to take suitable precautions to protect the projector from the effects of persistent and prolonged air contam- inants will culminate in extensive and irreversible ingrained optical damage. At this stage cleaning of PFWX-51B/PFWU-51B 10/02/2014 5 2.General the internal optical units will be noneffective and impracticable. Damage of this nature is under no circumstances covered under the manufacturer’s warranty and may deem the warranty null and void. In such a case the client shall be held solely responsible for all costs incurred during any repair. It is the clients responsibility to ensure at all times that the projector is protected from the harmful effects of hostile airborne particles in the environment of the projector. The manufacturer reserves the right to refuse repair if a projector has been subject to knowingly neglect, abandon or improper use. Main Power requirements The PFWX-51B/PFWU-51B projector operates from a nominal mono phase power net with a separate earth ground PE. Projector Power requirements PFWX-51B AC INPUT 100-240V 4.8A 50/60Hz PFWU-51B AC INPUT 100-240V 4.8A 50/60Hz The power cord required to connect the projector with the power net is delivered with the projector. Projector weight Do not underestimate the weight of the PFWX-51B/PFWU-51B projector. The projector weights about ±12 kg (±26.5 lb.) without lens. Be sure that the pedestal or ceiling mount on which the projector has to be installed is capable of handling five (5) times the complete load of the system. 2.2 Unpacking the projector 1. Remove the tape around the carton box, then open the box. 2. Take out the foam upper the projector. 3. Take out the projector. 6 PFWX-51B/PFWU-51B 10/02/2014 2.General After unpacking let the projector acclimatizes to a room temperature higher then 5°C (41°F) and lower then 35°C (95°F). Neglecting this may result in a start up failure of the Light Processor Unit. Save the original shipping carton and packing material, they will be necessary if you ever have to ship your projector. For maximum protection, repack your projector as it was originally packed at the factory. 2.3 Initial inspection General Before shipment, the projector was inspected and found to be free of mechanical and electrical defects. As soon as the projector is unpacked, inspect for any damage that may have occurred in transit. Save all packing material until the inspection is completed. If damage is found, file claim with carrier immediately. The Barco Sales and Service office should be notified as soon as possible. Box content After unpacking the projector it is recommended to check if all following items where included: • • • • • • Projector with standard lens mounted. Three power cords CD (Contents has this installation manual) One Safety manual One remote control unit (RCU) Two AAA size batteries for the RCU. Type: size-AAA (R03). Only Carbon-Zinc or Alkaline-Manganese Dioxide type batteries should be used. Lamp is mounted inside the lamp house at delivery. Mechanical check This check should confirm that there are no broken knobs or connectors, that the cabinet and panel surfaces are free of dents and scratches, and that the operating panel is not scratched or cracked. The Barco Sales and Service office should be notified as soon as possible if this is not the case. PFWX-51B/PFWU-51B 10/02/2014 7 2.General 2.4 Projector configurations The different configurations Depending on the installation the projector can be mounted in different ways, the different configurations are: 1. Front / Table (F/T) 2. Front / Ceiling (F/C) (upside down) 3. Rear / Table (R/T) 4. Rear / Ceiling (R/C) (upside down) Front projection The projector is installed, either in a table mount or ceiling mount configuration, at the same side of the screen as the audience. AUDIENCE SCREEN F/C F/T FLOOR Front projection 8 PFWX-51B/PFWU-51B 10/02/2014 2.General Rear projection The projector is installed, either in a table mount or ceiling mount configuration, at the other side of the screen opposite the audience. AUDIENCE BACKSTAGE SCREEN R/C R/T FLOOR Rear projection Positioning the projector SCREEN SW A SH SH PD B CD B CD SCREEN SW SCREEN FLOOR Positioning projector The projector should be installed at right angles (horizontally and vertically) to the screen at a distance PD. Note the distance (A) between lens centre and table surface is slightly variable. This distance (A) is nominal 8.3 cm in case all feet are turned in completely and the vertical lens shift is set to zero (0). On axis / off axis projection The position of the projector with reference to the screen may also be different depending on the installation. Basically the projector can be positioned in On-Axis or Off-Axis configuration. On-Axis configuration means that the projector is positioned so as to have the centre of the lens coinciding with the centre of the screen. Off-Axis projection is obtained by shifting the lens up, down, left or right. Several parameters can be calculated determining the position in any installation. Formula to calculate the distance CD for On-Axis projection: CD = SH/2 + B - A Shift range The lens can be shifted with respect to the DMD (P) which result in a shifted image on the screen (Off-Axis). A 100% shift means that the centre point of the projected image is shifted by half the screen size. In other words, the centre point of PFWX-51B/PFWU-51B 10/02/2014 9 2.General the projected image falls together with the outline of the image in an On-Axis projection. Due to mechanical and optical limitations it’s recommended to keep the shift values within the field of view (F) as illustrated below. Within these shift ranges the projector and lens perform excellently. Configuring the projector outside these shift ranges will result in a slight decline of image quality. F U P +110% SIDE VIEW +110% U -10 % D +10% L -30% R F L P D -30% -10% TOP VIEW P R +10% F Vertical and horizontal shift range P F DMD. Field of view. It is mechanical possible to shift outside the recommended field of view, but it will result in a decline of image quality depending on the used lens and the zoom position of the used lens. Furthermore, shifting too much in both directions will result in a blurred image corner. Horizontal and vertical projector tilt ranges Avoid to reduce the usage of lamp life. Suggest the projector rotated and mounted vertical angle not > ±15°. Side to side tilt, however, must not exceed ±10°. This limit ensures that the lamp in the projector operates properly and safely. B MAX MAX 10° 10° A A MAX MAX 10° 10° ±15° ±15° A C A B C Tilting allowed without problems No tilting allowed in this area No tilting allowed in this area 2.5 Projector air inlets and outlets Ventilation inlet: The internal cooling fan draws cool air from the ventilation inlet into the projector. Ventilation outlet: The hot air generated inside the projector is dispersed through the ventilation slot. Make sure the ventilation slot is free from 10 PFWX-51B/PFWU-51B 10/02/2014 2.General obstruction. Ventilation inlet Ventilation outlet 2.6 Installation process overview Quick setup The following steps describe briefly how to setup your PFWX-51B/PFWU-51B projector in a table mount front projection. Note that each step refers to a corresponding procedure, which is more detailed and illustrated. 1. Install the batteries of the remote control. See page 12: Remote control unit (RCU). 2. Place the projector on a solid table in front of the screen at the expected throw distance. Adjust the feet to ensure that the projector is installed at right angles (horizontally and vertically) with the screen. See page 19: Alignment of a table mounted projector and page 36: Adjusting the lens by horizontal and vertical lens shift. 3. Connect the projector with the local power net. See page 18: Connecting the projector with the power net. 4. Select and install an appropriate lens, which covers the throw ratio ( = screen size / projector screen distance). See page 9: Positioning the projector. 5. Switch ON the projector. See page 18: Connecting the projector with the power net. 6. Connect your source to the appropriate input module. See page 23: Input and Communication. 7. Zoom and shift the lens until the image is properly projected on the screen, Do this by using the “ZOOM” and “FOCUS” ring on the lens. If necessary, level the projector from side to side by turning the adjustable feet in or out. See page 16: Lens zoom. or adjust the Lens Shift manually. See page 36: Adjusting the lens by horizontal and vertical lens shift PFWX-51B/PFWU-51B 10/02/2014 11 3.Physical Installation 3. PHYSICAL INSTALLATION About this projector This chapter describes how the mechanical set up of the projector has to be done and how to realize the electrical connections. Overview • • • • • Remote control unit (RCU) Lenses Connecting the projector with the power net Alignment of a table mounted projector Mounting the ceiling mount 3.1 Remote control unit (RCU) Introduction Remove the cover by sliding it in the direction indicated by the arrow. ´ Insert two new AAA batteries (observe the polarity). Replace the cover. ´ Notes for the Remote control unit • • • • • • • • • 12 Be sure to insert the batteries in the corresponding orientations to match the polarities. Do not mix new batteries with used batteries as it would shorten the life of new batteries or cause leakage. Only used AAA batteries as instructed; do not attempt to insert different types of batteries into the remote control. If the remote is going to be unused for long periods of time, be sure to remove the batteries to prevent leakage, which could damage the remote control. The liquid contents in the batteries is harmful to the skin; do not touch the leakage with your bare hands directly. When installing fresh batteries, be sure to clean up the leakage thoroughly. Under most circumstances, you only need to point the remote control towards the screen and the IR signal would be reflected off the screen and picked up by the IR sensor on the projector.But under specific circumstances, the projector may fail to receive signals from the remote control due to environmental factors.When this happens, orient the remote control at the projector and try again. If the range of effective remote control signal reception decreases or if the remote control stops working, replace the batteries. If the infrared receiver is exposed to fluorescent lamp or strong sunlight, the remote control may not operate normally. Refer to the regulations enforced by your local government on the disposal of used batteries; improper disposal could damage the environment. PFWX-51B/PFWU-51B 10/02/2014 3.Physical Installation Remote Control overview ON/OFF HOME OK ARROW RIGHT ARROW UP ARROW LEFT ARROW DOWN LED INDICATION BATTERY COMPARTMENT IR LED'S Basic Remote Command result RCU Lite action start the projector press "ON/OFF" turn off the projector press "ON/OFF" show main menu on screen press "HOME" move through menu press "arrow keys" select button press "OK" select and return to previous menu press "OK" return to previous menu without selecting press "HOME" clear OSD Lite of screen press "HOME" PFWX-51B/PFWU-51B 10/02/2014 > 13 3.Physical Installation 3.2 Lenses Available lenses for the PFWX-51B/PFWU-51B projector PWFX-51B Lens standard Lens short throw Lens long throw R9832757 R9832758 R9832759 F lens (1.62-2.03:1) F lens (0.81:1) F lens (2.03-3.05:1) Lens standard Lens short throw Lens long throw R9832757 R9832758 R9832759 F lens (1.54-1.93:1) F lens (0.77:1) F lens (1.93-2.89:1) PWFU-51B Projection lenses are optional accessories. Please contact your local dealer to acquire the projection lens that suits your need most. Removing the Existing Lens From the Projector 1. Push down and release the lens shift cover to open. 2. Push the LENS RELEASE button to the unlock position. 3. Grasp the lens. 4. Rotate the lens counterclockwise. The lens disengages. 5. Carefully pull out the lens. 14 PFWX-51B/PFWU-51B 10/02/2014 3.Physical Installation Installing a New Lens Remove both end caps from the lens. 1. Align the notches and correctly position the electrical contact pad as shown in the picture. Electrical contact pins 2. Rotate the lens clockwise until it clicks in place. Electrical contact pins should be in the direction as shown in the picture. PFWX-51B/PFWU-51B 10/02/2014 15 3.Physical Installation Lens focus Sharpen the picture by rotating the focus ring. —> Lens zoom Adjust the projected picture to the size that you need using the zoom ring. Original image size 16 Zoom out Zoom in PFWX-51B/PFWU-51B 10/02/2014 3.Physical Installation Lens Shift In addition to using the adjustable feet to adjust projection angle, you can also use the Lens Shift function to adjust the projected image. • Moving the lens vertically The distance of vertical lens movement is +110% , -30% of half the screen height in both directions.For instance, if you are using a 80" × 50" screen, you will be able to move the image upwards no more than 27.5'' or downwards no more than 7.5''. Ra lennge o ad s sh f ve jus ift rtic tm al en t Range o fv lens shif ertical t adjustm ent This illustration shows normal vertical lens shift without the use of special specification lens or projector. Please make sure the center of lens is retangular to the center of the screen. • Moving the lens horizontally The distance of horizontal lens movement is 10% of half the screen width in both directions. For instance, if you are using a 80" × 50" screen, you will be able to move the image left or right by no more than 4". Ra n ho ge o riz f len ont s s al ad hif jus t tm en t Ra n ho ge o riz f len ont s s al ad hif jus t tm en t This illustration shows normal horizontal lens shift without the use of special specification lens or projector. PFWX-51B/PFWU-51B 10/02/2014 17 3.Physical Installation 3.3 Connecting the projector with the power net CAUTION: Use only the power cord provided with the projector. 1. Connect the female side of the power cord with the power input socket of the projector (1). 2. Secure the power plug by locking the plug holder clamp (2). Connect to Wall plug 3. Connect the male side of the power cord to the local power net. This power cord for Europe and Korea 18 This power cord for USA This power cord for China PFWX-51B/PFWU-51B 10/02/2014 3.Physical Installation CAUTION: Ensure that the power net meets the power requirements of the projector. WARNING: Do not attempt operation if the AC supply and cord are not within the specified voltage and power range. CAUTION: Once the projector is switched to standby, the lamp cooling fans will continue to run for approx- imately five minutes to ensure that the projector and lamp have sufficiently cooled, at which point the fans will automatically decrease to standby. To avoid thermal stress that can lead to premature lamp failure, never unplug the power cord while the lamp cooling fans are running. Never unplug the power cord to power down the projector, first switch off the power switch and then unplug the power cord. 3.4 Alignment of a table mounted projector How to align the projector 1. Place the projector in the desired location. Take into account the zoom range of the used lens and the size of the screen. 2. Project one of the internal grid patterns on the screen. 3. Turn the adjustable feet in or out until the projected grid pattern has a perfect rectangle shape and is leveled. PFWX-51B/PFWU-51B 10/02/2014 19 3.Physical Installation SCREEN When this is achieved, the projector is set horizontal and vertical at right angles to the screen. SCREEN Angle adjustment Angle adjustment 20 PFWX-51B/PFWU-51B 10/02/2014 3.Physical Installation 3.5 Mounting the Ceiling mount Necessary tools Open wrench 17 mm How to mount 1. Turn the projector upside down. 2. Adjustment knob to the back of the projector. Make sure that the mounting holes matches the holes in the projector. 3. Insert a bolt in each corner and turn in these bolts. 130.00 110.00 130.00 110.00 CEILING MOUNT SCREW M M4*0.7*12 PAN 26.50 165.00 NOte: Please check your support system for compatability. PFWX-51B/PFWU-51B 10/02/2014 21 4.Projector Parts and Functions 4. PROJECTOR PARTS AND FUNCTIONS Overview • • • • • Projector front view Projector Rear view Input and Communication Status lights of LED Connecting the projector to other devices 4.1 Projector front view Lens Len Shoft Cover LED indicator Lamp Ventilation outlet Infrared receiver Adjustable foot Adjust the height and angle of the projector with the adjustable foot The internal cooling fan draws hot air vis the ventilation outlet to the projector. 4.2 Projector Rear view Ventilation slot The hot air generated inside the projector is dispersed through the ventilation slot. Make sure the ventilation slot is free from obstruction. Infrared sensor 22 PFWX-51B/PFWU-51B 10/02/2014 4.Projector Parts and Functions 4.3 Input and Communication 1 15 14 2 3 9 4 5 6 13 7 12 8 11 10 1. HDMI HDCP compatible digital image input; connects to sources using HDMI or DVI. 2. DVI-D The projector can be connected to a PC or other device with a DVI-D output to the DVI-D connector. 3. DISPLAYPORT The projector can be connected to a display device with a displayport output to the displayport connector to video, audio, USB and data. PFWX-51B/PFWU-51B 10/02/2014 23 4.Projector Parts and Functions 4. RJ-45 Ethernet port The projector can be connected to a LAN (local area network) using the Ethernet port on the communication interface. Once connected to the LAN, users are capable of accessing the projector from any location, inside or outside (if allowed) their company network using the control software: Projector Toolset. This toolset locates the projector on the network in case there is a DHCP server or the user can insert the correct IP-address of the projector to access the projector. Once accessed, it is possible to check and manipulate all the projector settings. Remote diagnostics, control and monitoring of the projector can then become a daily and very simple operation. The network connectivity permits to detect potential errors and consequently improve the time to servicing. The connector used for the Ethernet ports (E) are of rugged Neutrik EtherCon RJ45 type, which is compatible with standard RJ45 cable connector. Straight (most common) as well as cross linked network cables can be used. PIN 1 2 3 4 5 6 7 8 RJ45 port Description RXD+ RXDTXD+ TXD- 5. USB CHARGE(1.5A) The projector can be connected to mobile device through the USB connector to provide battery charging function. USB cable is not included. 6. AUDIO OUT The projector can be connected to a device with an audio input to the audio out connector to relay an audio signal. 7. SERVICE The projector is connected through the port for servicing. 24 PFWX-51B/PFWU-51B 10/02/2014 4.Projector Parts and Functions 8. RS232 RS232 input The communication interface of the PFWX-51B/PFWU-51B projector supports RS232 serial communication. You can use the RS232 input to connect a local PC to your PFWX-51B/PFWU-51B projector. By this way you can configure and control your PFWX-51B/PFWU-51B projector from your local PC. Advantages of using RS232 serial communication: • • • • • easy adjustment of the projector via PC (or MAC). allow storage of multiple projector configurations and set ups. wide range of control possibilities. sending data to the projector (update). copying data from the projector (backup). PIN 1 2 3 4 5 6 7 8 9 RS232 input (Sub-D) port Signal (No connection) RD TD (No connection) Ground (No connection) RTS CTS (No connection) RS232 An Electronic Industries Association (EIA) serial digital interface standard specifying the characteristics of the communication path between two devices using either D-SUB 9 pins or D-SUB 25 pins connectors. This standard is used for relatively short-range communications and does not specify balanced control lines. RS-232 is a serial control standard with a set number of conductors, data rate, word length and type of connector to be used. The standard specifies component connection standards with regard to computer interface. It is also called RS-232-C, which is the third version of the RS-232 standard, and is functionally identical to the CCITT V.24 standard. Logical ’0’ is > + 3V, Logical ’1’ is < -3V. The range between -3V an d +3V is the transition zone. 9. VGA OUT Connect the RGB cable to a display (Loop thru only for VGA1). 10. VIDEO Connects to VCR, laser disc players or other component image sources.Also connects to the composite image synchronized input from RGBS input source. 11. S-VIDEO Standard S-Video input that connects to DVD players, satellite receiver or Super VHS (S-VHS) VCR. 12. YPbPr Standard and high definition (480i/480p/576i/576p/720p/1080i/1080p) component input, connects to DVD/HD-DVD/BD player, HD set-top-box or other SD/HD input source. PFWX-51B/PFWU-51B 10/02/2014 25 4.Projector Parts and Functions 13. RGBHV Optional multi purpose input which can be inserted in the free slots. Input Signal RGBHV Component Video Input (Sub-D) port B/Pb R/Pr B R Pb Pr G/Y G Y H H - V V - 14. VGA Standard 15-pin VGA connection socket to connect to RGB, high-definition component input or PC.The projector will automatically detect the resolution of the input signal. 15. 3D SYNC OUT(5V) The projector can be connected to a 3D emitter to send an infrared signal to 3D glasses (not supplied). Connect to a 3D IR emitter to allow for wireless synchronization with 3D glasses devices. 4.4 Status lights of LED Status LED location OFF/STAND BY The LED indicator shows solid RED when the projector is off and at standby mode. ON The LED indicator is off when the projector is on. ERROR The LED indicator is blinking at a 0.25 second interval when there is error occurred in projector. Please contact authorized service personnel for help. During start-up The LED indicator is blinking at a 2 seconds interval when the projector power on. 1 sec 1 sec 1 sec 1 sec 1 sec OFF/Standby ON Error During Start-Up 26 PFWX-51B/PFWU-51B 10/02/2014 4.Projector Parts and Functions 4.5 Opening the I/O cover How to open the I/O cover 1. Loosen the 3 screws from cover. 2. Pull out the right cover. 3. Push to release the left cover. And pull out the left cover. 4. Lift up the I/O cover. 5. Connect the desired input source. 6. Install the right and left cover back and tighten 3 screws. PFWX-51B/PFWU-51B 10/02/2014 27 4.Projector Parts and Functions 4.6 Connecting the projector to other devices HDMI connection Signals from image source offer the best projection image quality when sent through HDMI. Therefore, try to use input devices with HDMI output as the source of image. HDMI/DVI input source (BD/HD-DVD/DVD player, HD set-top-box, gaming consoles and so forth) DVI-D Input devices using DVI-D output, such as: desktop, notebook, or all-in-one computers, can be connected through the DVI-D port. Both DVI and HDCP DVI are supported and can be connected to the DVI connector of this projector. In case a HDCP DVI signal is connected to the DVI input, the DVI output image will not show the image of this source. A gray window will be displayed instead. 28 PFWX-51B/PFWU-51B 10/02/2014 4.Projector Parts and Functions DISPLAYPORT Connect your notebook and desktop computer or display device to the displayport connector to transmit video, audio, USB or data signals. AUDIO OUT (for HDMI, DISPLAYPORT source) Connect the projector to a device with an audio input port to relay the audio signal between the projector and the audio device. 3D SYNC OUT (5V): Connect 3D IR glasses transmitter Connect a 3D emitter device to the Displayport port to allow for the synchronization between the projector and 3D glasses. 3D IR glasses 3D IR Emitter PFWX-51B/PFWU-51B 10/02/2014 29 4.Projector Parts and Functions USB CHARGE (1.5A) Connect your handheld device to the USB port to use the power charging function (1.5A). Device charging cable not included. VGA connection Connect your PC or other devices with VGAoutput to the VGAinput connectors on the projector to be used as the source of image input. RGBHV connection G/Y B/Pb R/Pr H V Desk Top or Notebook 30 PFWX-51B/PFWU-51B 10/02/2014 4.Projector Parts and Functions VGA OUT (Loop thru only for VGA1) Connect the 15-pin D-sub cable and connect one end to the projector's VGA out port. Connect the other end to a monitor to use the loop-through function. YPbPr connection Take the 3 cabled RGB component video connectors from the source equipment to the projector’s jacks. DTV set-top-box or other component (YPbPr) input source Y Pb Pr S-VIDEO/VIDEO If the image input device offers both S-Video and Video connection, it is recommended that you choose S-Video to obtain better image quality. If both the S-Video and Video inputs are connected to the projector, the projector will prioritize SVideo signal input and image from the Video input will not be played. PFWX-51B/PFWU-51B 10/02/2014 31 4.Projector Parts and Functions RJ-45 Connect the RJ45 cable from a network device to the projector's RJ45 port. The Ethernet (RJ45) cable is not provided. (Ethernet) SERVICE: (Engineering use only) Connect the projector's service port to a PC using the supplied cable to perform maintenance. The port is for service only. RS-232C Connect a PC or home theater control/automation system (if present) to the RS-232 port on the PFWX-51B/PFWU-51B. Use a standard, 9-pin serial cable, wired straight-through. 32 PFWX-51B/PFWU-51B 10/02/2014 5.Getting Started 5. GETTING STARTED Overview • • • • • • • • • RCU Using the Remote Control and OSD Lite on Screen Power on projector Power off projector Range of effective remote control signal reception Source selection Changing OSD language Adjusting the lens by horizontal and vertical lens shift Introduction the OSD Lite on screen 5.1 RCU & Local keypad How controlling the projector? The projector can be controlled by the remote control unit. Remote control functions. This remote control includes a battery powered infrared (IR) transmitter that allows the user to control the projector remotely. This remote control is used for source selection, control, adaptation and set up. 5.2 Remote Control and OSD Lite on Screen Using Remote control and OSD Lite on Screen Basic OSD Lite naviagtion result show main menu of OSD Lite on screen RCU Lite action OSD Lite on screen press "HOME" main menu appears in bottom right corner To move through the OSD Lite press "arrow keys" button will turn red when the function is available go to desired function press "OK" the menu of the desired function will appear leave the menu or clear the screen press "HOME" the main menu will be displayed or when you are in the main menu the screen will be cleared Hotkey / Short Cut Remo result mute picture on the projector unmute picture on the projector PFWX-51B/PFWU-51B 10/02/2014 RCU Lite ->OSD Lite action -> on screen > press any key 33 5.Getting Started Main menu is on screen. RCU Lite -> OSD LIte go to button action -> on screen result select input manually > go to input desired (default setting = auto select) make the image brighter or darker use arrow keys to slide default setting= middle adapt the contrast between light/dark areas use arrow keys to slide default setting= middle > > > best condition to view “computer” images (default setting=PRESENTATION or VIDEO) select color preset most fitted for your image best option to view movies 100% bright adjust aspect ratio > go to aspect ratio desired (default setting = FILL) adjust keystone > > select language > go to language desired (default setting = ENGLISH) show lamp info > > show lamp mode > go to lamp mode desired (default setting = POWER) show projector info enter advanced menu > > > contact your service technician to enter the advanced menu > 5.3 Power on projector How to power on. Press on the remote control. The startup screen will display in approximately 30 seconds. When the projector is turned off, it is required to wait for at least 90 seconds to re-start the projector to complete the cooling of lamp. 34 PFWX-51B/PFWU-51B 10/02/2014 5.Getting Started 5.4 Power off projector How to power off 1. Press 2. Press key of the remote, a message displays on the projector's screen. key again to confirm, otherwise the message disappears after 5 seconds. 3. Let cool down the projector until the fan stop. At least 15 seconds for cooling cycle. 4. Disconnect the power cord from the power net. CAUTION: Never disconnect the power cord before the fan stop. 5.5 Range of effective remote control signal reception The diagram below illustrates the range of effective remote control signal reception. 12 m 40° 40° 12 m Avoid placing the remote control at places of high temperature or humidity as it could cause the remote control to malfunction. 5.6 Source selection Press HOME on the remote control to activate OSD Lite on Screen, then select " " for the desired source. INPUT PFWX-51B/PFWU-51B 10/02/2014 35 5.Getting Started 5.7 Changing OSD language By factory default, the OSD menu of the projector is displayed in English. If you wish to switch to a different language, Press the button on the remote control , select the language you prefer for the OSD. 5.8 Adjusting the lens by horizontal and vertical lens shift 1. Push down and release the top cover to open. 2. Turn the Horizontal and Vertical lens shift knobs to shift the lens horizontally or vertically. 3. Push the top cover down to close. Horizontal Lens Shift Lever Vertical Lens Shift Lever 36 PFWX-51B/PFWU-51B 10/02/2014 5.Getting Started 5.9 Introduction the OSD Lite on screen Press the button on the remote control, you can see the OSD Lite on screen as above picture. INPUT LANGUAGE Use this function to select the input souce. You can choice AUTO SELECT, HDMI, DVI, VGA. Use this function to select the different language of the OSD Lite on screen. Refer to page 52: Language. BRIGHTNESS INFO Adjust the level of black in the image to increas or decrease image brightness. Refer to page 41: Brightness. Show the information of lamp. CONTRAST Adjust the level of white in the image to increase or decrease image contrast. Refer to page 41: Contrast. COLOR MODE Select ECO, Normal, POWER mode of lamp. Refer to page 56: Lamp Mode. SERVICE Display this projector's information. Use this menu to select the display mode. ASPECT RATIO You can select differnt aspect via this function. Refer to page 50: Aspect Ratio. Advanced This function is for futher adjust the projector. For professional use. Refer to page 38: Advanced OSD Menu. KEYSTONE Use this function to adjust the from the tilt to not inclined. Refer to page 52: Keystone. PFWX-51B/PFWU-51B 10/02/2014 37 6.Advanced OSD Menu 6. ADVANCED OSD MENU The advanced menu only available for Professional use. Need enter the password to use this function. Overview The Advanced menu is the further function to control and align the projector, the following functions can be done: • Advanced OSD introduction. • Image adjustment: these adjustments are organized per image source and contain the aspect ratio, timings and image settings. • Settings 1: The Settings 1 menu allows you to save and access customized settings. • Settings 2: The Settings 2 menu allows you to save and access customized settings. 6.1 How to activate the Advanced OSD menu Press the button on the remote control to call the Basic OSD Lite on screen. Select the “ADVANCED” and press the password then the screen will show the advance OSD as below: The password for the advanced OSD is "left, left, right, down". 38 PFWX-51B/PFWU-51B 10/02/2014 6.Advanced OSD Menu 6.2 How to navigate in the Advanced menu structure? Once in the Advanced menu structure, use the or key on the remote control or on the local keypad to scroll through the items in the displayed menu. The selected item will get a background color. To activate a selected submenu or function, press on the remote. When on a submenu, to return one step to the parent menu, press HOME. To escape the menu structure when on a menu, press HOME. How to make an OSD adjustment? With the remote control navigate through the Advanced menu structure until the desired item is selected. Press the key until the desired item is reached. Press With the remote control, press the or or to finalize the adjustment. key until the desired value (setup) is reached. Press EXIT to finalize the adjustment. Direct adjustment within the menu: Use the or key to directly adjust the current value. or, Via bar scale adjustment : Once an item is selected, press to open the bar scale menu. Use the or key to adjust the current value. The bar scale will move accordingly. Press to finalize the adjustment. or, When the bar scale is displayed, via direct input. Press to activate the input field. 6.3 Advanced menu memory Each menu with sub menus, remembers its last selected sub item value even when leaving the menu structure and that as long as the projector is running. PFWX-51B/PFWU-51B 10/02/2014 39 7.Image 7. IMAGE Overview • • • • • • • • Image menu overview Display Mode Brightness Contrast Computer Auto Image Advanced Input Balance 7.1 Image menu overview Image Display Mode Presentation, Bright, Video, User1 Brightness 0~100 Contrast 0~100 Computer Auto Image Execute Advanced Input Balance Image Image Computer Advanced Horizontal Position -5~5 Vertical Position -5~5 Frequency 0~31 Tracking -5~5 Brilliant Color -5~5 Sharpness -5~5 Gamma 0~31 Color Temperature Warm, Normal, Cold Video AGC On, Off Video Saturation 0~100 Video Tint 0~100 Input Configuration Auto, YUV HD, YUV STD, RGB-PC, RGB-Video Input Balance Image Input Balance Black Balance Offset Image Input Balance Black Balance Offset Red Offset -1023~1023 Green Offset -1023~1023 Blue Offset -1023~1023 Image Input Balance White Balance Red Gain 0~200 Green Gain 0~200 Blue Gain 0~200 White Balance Depending on the type of the connected source, some settings are grayed out. 40 PFWX-51B/PFWU-51B 10/02/2014 7.Image 7.2 Display Mode There are many factory presets optimized for various types of images. • • • • Presentation: Good color and brightness from PC input. Bright: Maximum brightness from PC input. Movie: For home theater. User 1: User’s own settings. 7.3 Brightness The brightness function is used to adjust the black level in the input picture. It adds or subtracts an offset, or bias in to the red, green and blue signals. Brightness adjustment can be done with the Brightness key on the RCU or via the menu structure. It is recommended that you adjust the image to the following status: • • • • • The darkest black bar of the image should disappear into the background. The dark gray area should be barely visible. The light gray area should be clearly visible. The white area should appear real and mellow. The image should only display black, gray and white (with no other colors). 7.4 Contrast The contrast function is used to adjust the contrast between the light and the dark areas of the displayed image. It applies a gain to the red, green and blue signals. Contrast adjustment can be done with the Contrast key on the RCU or via the menu structure. The following image illustrates the results of direct contrast adjustment using a random image: Lowered contrast Original image Enhanced contrast Contrast and Brightness are interrelated options that affect one another; when you adjust one of them, you might have to fine tune other settings to get the best projection results. PFWX-51B/PFWU-51B 10/02/2014 41 7.Image The following image illustrates the results of direct brightness adjustment using a random image: Reduced brightness Original image Enhanced brightness 7.5 Computer Horizontal Position Use or to adjust the projected image’s horizontal position. If the projected image is not at the center of the screen (i.e. shifted to right or left) and ends up being cropped, use this function to adjust the image’s horizontal position.The following image is an example of test image from an external signal source: Native picture Skewed left Skewed right Vertical Position Use or to adjust the projected image’s vertical position. If the projected image is not at the center of the screen (i.e. shifted up or down) and ends up being cropped, use this function to adjust the image’s vertical position.The following image is an example of test image from an external signal source: Native picture 原始圖面 Skewed down 圖面下偏 Skewed Up 圖面上偏 It is recommended that when adjusting the image, the horizontal total should be adjusted before the horizontal phase. However, if the image still flickers even after you have adjusted both, try lowering the image noise. Frequency Use or to adjust the projected image’s phase. Use this function to adjust the phase of pixel sampling clock (relative to input signal). Should the image still flicker or show noise (i.e. edges on texts) after optimization, adjust phase accordingly. 42 PFWX-51B/PFWU-51B 10/02/2014 7.Image Tracking Press or to adjust the horizontal total. Use this function to adjust the clock frequency of pixel sampling (horizontal pixel frequency of the analog input source generated by the ADC). If you notice flickering or verticle lines in the image, it means that the pixel sampling frequency is insufficient. You can use this function to adjust the frequency to achieve consistent image quality. The following image is an example of test image from an external signal source: ² Adjust image quality by changing the value of horizontal total to smoothen the image. In order to adjust timings the pattern should be used is pixel (on/off) For saving usage. If user needs to clear those Signal info saving function: (Available for VGA and BNC sources.) When a signal is locked and one of those settings(Horizontal Position/ Vertical Position/ Frequency/ Tracking) is adjusted, the current timing info and the settings will be auto stored into memory. If again, when a new timing has been locked and which is the same as one of the previously stored timings in memory, system will auto load and apply those settings for this timing which has been stored in the memory. Each source has 20 memory locations settings of current timing, please execute the Auto Image which is located at Advanced Menu->Image menu page to clear the current timing settings. NOte: An execution of Reset All will clear all of saved timing info. 7.6 Auto Image When Auto Image was selected in the Advanced menu, press OK to execute the automatic image adjustment function. By executing this function, the projector will resync the image. Use this function when the image source is unstable or when you notice deterioration in image quality and the projector will automatically adjust the image size, phase and timing. (The adjustment also applies to PIP input source). NOte: If user needs to clear Hor.Position, Ver.Position, Frequency, Tracking settings stored in memory of current timing, please execute the Auto Image which is located at Advanced Menu > Image menu page. This function will use auto locked result as setting value instead. PFWX-51B/PFWU-51B 10/02/2014 43 7.Image 7.7 Advanced Brilliant Color This feature utilizes a new color processing algorithm and system level enhancements to enable higher brightness while providing truer, more vibrant colors in picture. It enable a greater than 50% brightness increase in mid-tone images, which are common in video and natural senes, so the projector reproduces images in realistic and true colors. Sharpness The adjustment of sharpness primarily changes the value of high frequency detail. You can connect the projector to an external image source to display an image resembling the one shown below to adjust the image sharpness. The following image illustrates the results of direct sharpness adjustment using a random image: Reduced sharpness Original image Enhancedsharpness Gamma Different Gamma settings will affect viewers' perception of the image. Generally speaking, for images that are darker, it is recommended that Gamma be set higher to yield better image quality in darker regions by sacrificing details in brighter areas. In contrast, when projecting brighter images, you can set the Gamma lower to give up details in the darker areas to make the brighter areas (i.e. clouds) more visible. You can choose from five different gamma settings (1.8, 2.0, 2.2, 2.4, B&W, Linear) on the projector. The projector's default gamma value is at 2.2. Every setting has precisely defined phases to display all primary colors (red, green, blue) and secondary colors (yellow, cyan, magenta) in millions of pixels. Changing any number in the setting will change the resulting color and rearrange the color "triangle". Color Temperature You can choose from Warm, Normal and Cold. Color temperature refers to the change in light color under different energies that is perceived by the naked eye. The change of color temperature from Warm to Cold for visible light goes from orange red Ò white Ò blue The projector’s default color temperature is set at Normal and it is suitable for most situations. As color temperature change to Cold, the image will appear to be more blue; as it change to Warm, the image will appear redder. When you choose “Native”, the projector will disable the white adjustment function of the input device. 44 PFWX-51B/PFWU-51B 10/02/2014 7.Image Video AGC Video AGC refers to automatic gain correction function. When enabled, the AGC function applies gain corrections on the input necessary to display correct output colors. Video Saturation Press or to adjust the saturation of the projected image.If the color of the projected image seems to be overly bright and vivid, decrease the color saturation; if the color seems white and washed out, increase the color saturation. Video Tint Press or to adjust the tint (balance between magenta and green) of the projected image. Lowering the value will make the image appear greener; increasing the value will make the image appear redder. Input Configuration Press or range). to adjust the Input Configuration. This function adjusts the signal color space and output range level (Limit/Full 7.8 Input Balance Black Balance Offset This function involves the adjustment of the following red, green and blue offsets. The text itself is decorative. • Red Offset Press or to adjust the offset of red in dark scales. • Green Offset Press or to adjust the offset of green in dark scales. • Blue Offset Press or to adjust the offset of blue in dark scales. White Balance This function involves the adjustment of the following red, green and blue gains. The text itself is decorative. • Red Gain Press or • Green Gain Press or • Green Gain Press or to adjust the gain of red in bright scales. to adjust the gain of green in bright scales. to adjust the gain of blue in bright scales. Unbalanced color signals When transporting signals, there is always a risk of deterioration of the information contained in the signals. In case of information contained in the amplitude of the signals which is the case of data color signals (R, G, B),image 9-29 , we are quite sure that the amplitude of these color signals is subject to alterations. An example of alteration may be a DC component added to the signal, in the form of a DC offset repositioning the black level, since this black level (“brightness”) will become crucial later on (clamping circuit) it will result in “black not being black”. Another value that is subject to alteration is the amplitude of the signal, resulting in an altered “Gain” of the signal (“white level” or contrast). PFWX-51B/PFWU-51B 10/02/2014 45 7.Image The alterations of the three color signals will happen independently i.e. the colors will end to be unbalanced, image 9-30 B 0.7V Black level Image 9-29 G B R ∆G ∆R ∆Β Black level One can conclude here that a good color tracking can only be met by using three previously (input) balanced color signals Analog Digital Conversion The analog color signals must pass through an Analog/Digital conversion circuit prior to any digital processing in the PMP. A typical ADC transforms the analog value into an 8 bit coded digital signal. The graphic shows that when converting a signal containing a DC offset component the range of the converter is not optimally used. ADC R 255 i2 : video information ∆ 0 i1 : superfluous information Black level One can conclude here that a good data conversion can only be met by using three previously (input) balanced color signals The objective of input balancing The objective in input balancing is to “set” the same black level and the same white level for the three colors of a particular input source. Black level setting : brightness White level setting : contrast The same absolute black and white level for the three colors allows the same reference for Brightness and Contrast control of the picture ! These two references also set the range in which the ADC will work for that particular source (this explains also why each input balance setting is linked to a particular source and thus saved in the image file). 46 PFWX-51B/PFWU-51B 10/02/2014 7.Image Adjusting the input balance To balance the three color signals of a particular source there are conditions; in fact we must know the black and the white level of the source i.e.: 1. The source in question must be able to generate a white signal, ideally a 100% white (background) full screen pattern 2. The source in question must be able to generate a black signal, ideally a 100% black (background) full screen pattern A B White balance : In the projector, we will set the contrast for each color until we get a 100% light output picture when projecting a 100% white image (image A) Black balance : In the projector, we will set the brightness for each color until we get a 0% light output picture when projecting a 100% black image (image B). The changeover from min to max is indicated by the apparition of bright spots also called “digital noise” An alternative to a full screen White/black pattern is the standard gray scale pattern, the white bar will be used for white balance and the black bar for black balance. PFWX-51B/PFWU-51B 10/02/2014 47 8.Settings 1 8. SETTINGS 1 Overview • • • • • • • • Settings 1 menu overview Source Projection Aspect Ratio Keystone Digital Zoom Advanced 1 Advanced 2 8.1 Settings 1 menu overview Source Settings 1 Projection Front_Floor, Rear_Floor, Front_Ceiling, Rear_Ceiling Aspect Ratio Fill, 4:3, 16:9, Letter Box, Native, 2.35:1 Keystone -40~40 Digital Zoom -10~10 Advanced 1 Advanced 2 Settings 1 Settings 1 Advanced 1 Source Source DVI, HDMI, Display Port, VGA1, VGA2, BNC, Component Video, S-Video, Composite Video Language ENGLISH, FRENCH, SIMPLIFIED_CHINESE, JAPANESE, GERMAN, SPANISH, KOREAN, RUSSIAN TURKISH Security Lock On, Off Blank Screen Blank, Red, Green, Blue, White Splash Logo Std., Off, User Closed Captioning On, Off 3D Setting Screen Capture 48 PFWX-51B/PFWU-51B 10/02/2014 8.Settings 1 Settings 1 Advanced 1 Setting 3D Off, DLP-Link, IR 3D Sync Invert Off, On 3D Format Frame Sequential, Top/Bottom, Side-By-Side, Frame Packing (3D FramePacking HDMI source only) Test Pattern None, Grid, White, Red, Green, Blue, Black H Image Shift -50~50 V Image Shift -50~50 3D Settings 1 Advanced 2 8.2 Source Use this function to specify the source of image connected to the rear of the projector. For instance, if you have connected your PC as the video input source, you can choose RGB D-15(RGB-HV/SOG) to be the input for image projection. Options of input available on the projector include: DVI, HDMI, DisplayPort, VGA 1, VGA 2, BNC, Component Video, S-Video, Compositive Video. 8.3 Projection By default, the projector is configured for “frontal projection - desktop installation”. If you choose to install your projector in other setups, be sure to adjust the screen orientation to achieve the correct projection mode. Front projection - ceiling mode Press HOME OSD Lite MENU ADVANCED Enter Password Settings 1 Projection configured for “frontal projection - ceiling mode”. ; the projector is now Correct Picture canoe PFWX-51B/PFWU-51B 10/02/2014 canoe canoe 49 8.Settings 1 Rear projection - desktop installation Press HOME OSD Lite MENU ADVANCED Enter Password Settings 1 Projection configured for “rear projection - desktop installation”. ; the projector is now can Correct Picture oe eon canoe ac Rear projection - ceiling mode Press HOME OSD Lite MENU ADVANCED Enter Password Settings 1 Projection configured for "rear projection-ceiling mode". ; the projector is now Correct Picture canoe canoe eonac Front projection - desktop installation Press HOME OSD Lite MENU ADVANCED Enter Password Settings 1 Projection configured for "frontal projection - desktop installation". ; the projector is now 8.4 Aspect Ratio Relation between the horizontal & vertical dimension in which the window will be displayed, e.g. 4 by 3 or 16 by 9. Can also be expressed as a decimal number, such as 1.77. The larger the ratio or decimal, the wider the image (or the less the image is squared). The aspect ratio setting forces the projector to project an image using a defined aspect ratio. Aspect ratio Fill 4:3 16:9 Letterbox Native 2.35:1 Description Scale image to fill the screen vertically and add horizontal pillar-boxing. Standard television format Wide screen television format / anamorphic format 1.33:1 Scale image to fit screen Film format The projector’s full image size is 16:10 (1280x800, 1920×1200 dots).The following diagram illustrates the difference in various aspect ratio settings: 50 PFWX-51B/PFWU-51B 10/02/2014 8.Settings 1 Native input 16:10 Output aspect ratio 4:3 Output aspect ratio 16:9 Output aspect ratio 2.35 Output aspect ratio Letterbox Output aspect ratio Native Native input 4:3 Output aspect ratio 4:3 Output aspect ratio 16:9 Output aspect ratio 2.35 Output aspect ratio Letterbox Output aspect ratio Native Cropped portion of the image That when used for commercial purposes, including: projection of image in movie theaters, hotels, cafeteria and other public venues, compression or extension of image achieved through the change of aspect ratio may constitute copyright infringement to the rightful owner of the image. Please do so at your own discretion. PFWX-51B/PFWU-51B 10/02/2014 51 8.Settings 1 8.5 Keystone Vertical Keystone Use this function to correct keystoning caused by projection angle. —> The summation of the absolute value vertical keystone is limited to less than or equal to 40 8.6 Digital Zoom Press to digitally reduce the size of the image. Press to digitally magnify the size of the image. 8.7 Advanced 1 Language The user can change the language of the on screen menus and the local display menus to one of the available languages. You can choose from the following nine languages: English, French, Spanish, German, Simplified Chinese, Japanese, Korean, Russian and Turkish. Security Lock Press or to enable or disable security lock function. The password menu displays when Security Lock is On. Use the following keys HOME to cancel. , , or to setup a password.. Press Reset password If you need to reset password, please contact your service technician. Blank Screen Press or to select different color to blank the screen. Splash Logo You can use this function to have the projector display the Barco logo in the start up screen. Set Std to display the Barco logo during start up and Off to display a blank image. If no screen has been captured, the BARCO logo will be the start logo during start up when set to User. 52 PFWX-51B/PFWU-51B 10/02/2014 8.Settings 1 Closed Captioning Select the screen to display closed captioning. 3D Setting Enter the 3D menu. Select 3D options such as 3D, 3D Sync Invert, and 3D Format. 3D • Off: Close 3D mode. • DLP Link: Select DLP Link to use optimized settings for DLP Link 3D Glasses. • IR: Select IR to use optimized settings for IR-based 3D images. When Input source is HDMI 1.4a with AVI info frame, Default Value is DLP Link. Possible value is DLP-Link/IR. When Input source is VGA/DVI/Video/Svideo/HDMI 3D no Info frame, Default Value is Off. Possible value is Off/DLP-Link/IR. 3D Sync Invert Press or to enable or disable the 3D Sync invert function to invert images. 3D Format • • • • Frame Sequential: Display 3D signal in Frame Sequential format. Top/Bottom: Display 3D signal in Top and Bottom format. Side-By-Side: Display 3D signal in Side-by-Side format. Frame Packing (only for 3D source): The left and right images are packed into one video frame (twice the normal bandwith). Screen Capture Execute the Screen Capture function. After the screen has been successfully captured, the Splash Logo function will be set to User automatically and the logo will be replaced with this captured screen during start up. 8.8 Advanced 2 Test Patterns The projector comes with some standard built-in patterns for testers to calibrate the equipment. These include: None, Grid, White, Red, Green, Blue, Black. H Image Shift Shifts the projected image position horizontally. • Press • Press to move the image left on the projected screen. to move the image right on the projected screen. V Image Shift Shifts the projected image position vertically. • Press • Press to move the image up on the projected screen. to move the image down on the projected screen. PFWX-51B/PFWU-51B 10/02/2014 53 9.Settings 2 9. SETTINGS 2 Overview • • • • • • • • • Settings 2 menu overview Auto Source No Signal Power Off Auto Power On Lamp Mode Reset All Status Advanced 1 Advanced 2 9.1 Settings 2 menu overview Auto Source Off, On No Signal Power Off Off, On Settings 2 Auto Power On Off, On Lamp Mode ECO, Normal, POWER Reset All Status Advanced 1 Advanced 2 Active Source Video Information Settings 2 Status Lamp Hours (ECO, Normal, POWER) Software Version Serial Number Settings 2 Advanced 1 Menu Position Left, Right, Center, Down, Up Translucent Menu 0%, 25%, 50%, 75%, 100% Low Power Mode Off, Low Power Fan Speed Normal, High Lamp Hour Reset Network 54 PFWX-51B/PFWU-51B 10/02/2014 9.Settings 2 Settings 2 Advanced 1 Network Settings 2 Advanced 2 Settings 2 Advanced 1 Network Network State Connect, Disconnect DHCP Off, On IP Address 0~255, 0~255, 0~255, 0~255 Subnet Mask 0~255, 0~255, 0~255, 0~255 Gateway 0~255, 0~255, 0~255, 0~255 DNS 0~255, 0~255, 0~255, 0~255 Apply OK / Cancel Sleep Timer 0~600 Source Filter DVI Disable, Enable HDMI Disable, Enable DisplayPort Disable, Enable VGA1 Disable, Enable VGA2 Disable, Enable BNC Disable, Enable Component Video Disable, Enable S-Video Disable, Enable Composite Video Disable, Enable 9.2 Auto Source On Defaul setting. By enabling this function, the projector will automatically determine the source of input every time it is turned on so that the user will not have to make the selection on the OSD Menu. Setting the function off will require the user to specify source of image input on the OSD Menu in order for the projector to display the intended image. PFWX-51B/PFWU-51B 10/02/2014 55 9.Settings 2 9.3 No Signal Power Off Automatically shut off when no signal. (in minutes). If siwitch to On, the projector will automatically shut off after 15 minutes when no signal. 9.4 Auto Power On Automatically power on when AC power applied. 9.5 Lamp Mode When the lamp is set to ECO mode, the lamp is running at 280W. If the ambient temperature is higher than 35 degree Celsius, lamp will operate at ECO mode. In this case, lamp mode selection is unavailable. Lamp mode selection is available once the ambient temperature drops below 35 degree Celsius. • ECO When set to Eco mode, the wattage of the lamp will be at 280W. If the surrounding environment is sufficiently dark or if you do not require intense brightness, you can set the lamp to Eco mode to prolong its usage life. • Normal When set to Normal mode, the wattage of the lamp will be at 370W. If the projection environment requires brighter image, you can set the lamp to Normal for the highest projection brightness. • POWER When set to Power mode, the wattage of lamp will be at 330W. you can set the lamp to Power mode to prolong its usage life. 9.6 Reset All All settings of the projector will be set to the original factory settings. All user settings are erased with this operation. This function will not apply to items including no signal, network, Projector control, startup Logo, language, High Altitute mode and lamp hours When Factory Reset is executed, all source memories created by the projector (i.e. timings files) will be erased 9.7 Status Active Source To show which source is activated Video Information Showing resolution/H, V information at RGB mode. Showing color standard at Video mode. Lamp Hours (ECO, Normal, POWER) Lamp hour used information. ECO, Normal and POWER counter are separated. Software Version Showing system software version. Serial Number Showing serial number of this projector. 56 PFWX-51B/PFWU-51B 10/02/2014 9.Settings 2 9.8 Advanced 1 Menu Position You can use this function to designate which area on the image the OSD Menu will appear. As you can see from the diagram below, there are five positions where you can choose to have the OSD Menu displayed.The default setting is “Center”. UP Left Center Right Down Translucent Menu Press or to select OSD background translucent level. Low Power Mode The projector can be connected to a network via its RS232 and/or RJ45 port for remote operation with two separate boards to control the signal source from RS-232 and/or RJ45 ports. For complete remote operation of the projector over RJ45 port, it is recommended the "Low power mode" of OSD to be "Off" option, even if the projector in "Standby" state. By setting "Low power mode" being "Off" option, user would not be able o conserve power consumption in "Standby" state. Fan Speed Use this function to control the projector's cooling fan. You can set it to Normal or High. The default setting is Normal. Under normal circumstances, the projector will operate normally with this function set to Normal. By default, the projector will detect the temperature of the surrounding environment to regulate the speed of the cooling fan. When the ambient temperature rises, fan speed will increase (generates louder noise) to make sure the heat inside the projector gets discharged and keep the projector working normally. However, if you were to operate the projector in environment of excessive heat or in areas of high altitude, the projector may automatically shut down. When this happens, you can enable this function by setting it to High to force the cooling fan to work at a higher speed to regulate the temperature inside the projector. • High altitude region refers to area with elevation over 1500 meters (4900 feet). • When operating in normal altitude environments, the projector will adjust the cooling fan according to the temperature of the working environment. When the temperature rises above 30C, the projector will automatically increase fan speed. • According to the product specification, the maximum operating altitude for the projector is at 3000m@25C.This means that you should not be operating the projector in high altitudes when the working environment is over 25C. (Due to the air thinning substantially at high altitudes, the result of cooling achieved by the cooling fan is significantly reduced compared to operation on level ground. With low atmospheric pressure and high operating temperature, the cooling fan will not be able to disperse the heat adequately) Lamp Hour Reset Use this function to reset the hours for lamp to zero. After replacing the lamp, remember to reset the lamp hours to ensure the accuracy of lamp hours displayed in the OSD Menu PFWX-51B/PFWU-51B 10/02/2014 57 9.Settings 2 Network Projector (Ethernet) Wired LAN Terminal functionalites Remote control and monitoring of a projector from a PC (or Laptop) via wired LAN is also possible. Compatibility with Crestron / AMX (Device Discovery) / Extron control boxes enables not only collective projector management on a network but also management from a control panel on a PC (or Laptop) browser screen. • Crestron is a registered trademark of Crestron Electronics, Inc. of the United States. • Barco's Projector Toolset is a registered trademark of Barco, Inc. / Barco Federal Systems, LLC. Supported External Devices This projector is supported by the specified commands of the Crestron Electronics controller and related software (ex, RoomView®). http://www.crestron.com/ This projector is supported by Barco's Projector Toolset. http://www.barco.com/ For more detail of information about the diverse types of external devices which can be connected to the LAN/RJ45 port and remote/control the projector, as well as the related control commands supporting for each external device, kindly please get contact with the Support-Service team directly. Herewith the Web-Information of Projector status. By factory default, the network configuration is DHCP On. As well, projector can support to change to settings, DHCP Off. For more information, please visit http://www.barco.com/. IP Address Internet Protocol. The network layer of TCP/IP. Required for communication with the internet. 58 PFWX-51B/PFWU-51B 10/02/2014 9.Settings 2 Can only be used with a wireless network module installed. Subnet mask A number that is used to identify a subnetwork so that IP addresses can be shared on a local area network. Can only be used with a wireless network module installed. Subnet for Wired and Wifi must be different ! Gateway A router that serves as an entry point into and exit point out of a network. For example, a local network (LAN) may need a gateway to connect it to a wide area network (WAN) or to the Internet. Can only be used with a wireless network module installed. DHCP Dynamic host configuration protocol. DHCP is a communications protocol that lets network administrators manage centrally and automate the assignment of IP addresses in an organization’s network. Using the Internet Protocol, each machine that can connect to the Internet needs a unique IP address. When an organization sets up its computer users with a connection to the Internet, an IP address must be assigned to each machine. Without DHCP, the IP address must be entered manually at each computer and, if computers move to another location in another part of the network, a new IP address must be entered. DHCP lets a network administrator supervise and distribute IP addresses from a central point and automatically sends a new IP address when a computer is plugged into a different place in the network. Can only be used with a wireless network module installed. 9.9 Advanced 2 Sleep Timer Set the Sleep Timer interval. The projector powers off after the specified time period of inactivity (regardless of signal). Source Filter Press or to select the input sourcee,and press PFWX-51B/PFWU-51B 10/02/2014 or to enable or disable the automatic input searching.. 59 10.Maintenance 10. MAINTENANCE 10.1 Lamp Replacement The lifecycle of ordinary projection lamp typically lasts for 3500 hours before requiring replacement (different lamp configurations will affect lamp life). From the OSD Menu, you can go to " page 57: Lamp Hour Reset ". To check how long a lamp has been used. You should also replace the lamp when the projected image gets noticeably darker. Contact your local dealer to purchase new certified lamps for your projector. This procedure may only be performed by qualified technical service personnel. How to replace the projector lamp WARNING: Unplug the power cord before starting the procedure. Keep all flammable items away from lamp Never to remodel or disassembly on lamp housing Lamp contains mercury. If lamp bursts during operation. Keep yourself in sufficiently ventilate area in order to avoid inhaling mercury. 1. Turn off the projector and unplug the power cord. Let the projector cool for approximately 60 minutes before removing the lamp module for replacement. When you turn off the projector, the lamp inside the projector will still be very hot (approximately 200 ~ 300°C). If you attempt to replace the lamp without allowing the projector to cool, you could risk scalding yourself. This is why you should wait for no less than 60 minutes for the lamp to cool down in order to perform the replacement safely. 2. Loosen the screws from cover. 3. Pull out the right cover. 4. Use a screw driver to loosen the screws as shwon in the illustration. Grasp the metal rod on the lamp cover and pull the lamp out. 60 PFWX-51B/PFWU-51B 10/02/2014 10.Maintenance 5. Insert the new lamp in the direction shown in the illustration into the lamp assembly; tighten the two screws using a screw diver and make sure the lamp is firmly secured to prevent the lamp from shaking or poor contact. 6. Replace the right cover and tighten the screw. 7. Reconnect power to the projector and reset the lamp usage timer. Refer to page 57: Lamp Hour Reset. PFWX-51B/PFWU-51B 10/02/2014 61 10.Maintenance 10.2 Clean the dust 1. Remove most contamination with a vacuum cleaner. 2. Blow remaining dust away with compressed air in an other room or outside. 10.3 Cleaning the lens To minimize the possibility of damage to optical coatings, or scratches to lens surfaces, we have developed recommendations for cleaning. FIRST, we recommend you try to remove any material from the lens by blowing it off with clean, dry deionized air. DO NOT use any liquid to clean the lenses. Necessary tools Toraysee TM cloth (delivered together with the lens kit). Order number: R379058. How to clean the lens? 1. Always wipe lenses with a CLEAN Toraysee TM cloth. 2. Wipe lenses in a one single direction. Warning: Do not wipe back and forwards across the lens surface as this tends to grind dirt into the coating. 3. Do not leave the cleaning cloth in either an open room or lab coat pocket, as doing so can contaminate the cloth. 4. If smears occur when cleaning lenses, replace the cloth. Smears are the first indication of a dirty cloth. CAUTION: Do not use fabric softener when washing the cleaning cloth or softener sheets when drying the cloth. Do not use liquid cleaners on the cloth as doing so will contaminate the cloth. Other lenses can also be cleaned safely with this Toraysee TM cloth. 10.4 Cleaning the exterior of the projector How to clean the exterior of the projector? 1. Power off the projector and unplug the projector from the mains power net. 2. Clean the housing of the projector with a damp cloth. Stubborn stains may be removed with a cloth lightly dampened with a mild detergent solution. 62 PFWX-51B/PFWU-51B 10/02/2014 10.Maintenance 10.5 Simple troubleshooting The following table offers a list of common problems with projectors and how to troubleshoot. If the recommended solutions fail to resolve your problem, contact your local dealer to arrange for servicing; do not attempt to service the projector by yourself. Problem Possible cause Solution 1. The projector may be unplugged. 1. Plug the projector's power cord into a wall outlet. 2. T he AC socket may be faulty. You cannot turn on the projector 3. The lens cover is not replaced properly. 2. M ake sure the AC socket is working properly. 3. Make sure the lens cover has been properly replaced. You cannot turn on the projector after turning it off You have connected the projector to a DVD player as the input source but the image appears broken or split in halves. The picture looks dim The remote control does not operate normally You are able to turn on the projector and access the OSD Menu but no picture appears. The image is too bright or the bright areas are blurry You will not be able to turn on the projector within two minutes after you have just turned it off. This feature is designed to protect the lamp. The DVD player is connected to the projector Disable the progress scanning function on through component cables and you have set the DVD player. it to progressive scan. 1. The image brightness, contrast, color and tint might need proper adjustment. 1. Adjust the image brightness, contrast, color and tint. 2. The lamp is due for replacement. 2. Replace the projector lamp. 1. The battery might have run out. 1. Replace new batteries. 2. Y ou might have inserted the batteries in the wrong orientations. 2. Make sure the batteries are inserted in the right orientation. 3. You may be operating the remote control 3. Adjust the distance/angle between the too far away from the projector's IR sensor projector and the remote control and try or exceeded the maximum angle of signal again; if there are obstacles between the reception ; there might be an obstacle projector and the remote or source of between the projector and the remote intense light near the IR sensor resolve control or there might be a source of these situations and try again. intense light near the IR receiver. 4. Press the OK button on the remote control 4. T he remote control's address is not followed by the Address button until the consistent with the projector's address. panel of the remote control flashes once (approximately 5 seconds) and try again. 1. The projector may not be turned on properly or you have not selected the correct input source. The contrast might have been set too high. 1. The lens may not be in focus. PFWX-51B/PFWU-51B 10/02/2014 1. Make sure the projector is turned on properly and select the correct input source. 2. Y ou might not have connected the source 2. C heck the connection between the device correctly or the source might not be projector and the input device. connected to the projector at all. The image appears washed out The image brightness might have been set or the dark areas appear too too high. bright The image is blurry Wait for the projector to cool down completely before starting it up again (the projector's STAND BY indicator will turn blue) Lower contrast settings. Lower brightness settings. 1. Adjust Lines focus. 2. T he temperature or humidity of the 2. T urn of the projector first and wait for the projector's working environment may have moisture in the projector to evaporate. changed in mid operation (i.e. going from cold to warm or dry to humid), leading to condensation of moisture inside the projector. 63 10.Maintenance Problem The color of the image looks pale. Possible cause Solution The input signal type (RGBHV/YUV) might not have been connected properly. Check to make sure that the connections between the projector and the input device are correct. 1. The cables might not have been properly connected or the input device itself may be faulty. The image flashes occasionally. 2. If the problem persists, it may also mean the lamp might be faulty. The colors of the projected image are out of place (i.e. displaying red as blue). 1. Make sure the connector and the input device have been properly connected; check to see if the input device is in normal working order. 2. Replace the projector lamp. The G/Y, R/Pr, B/Pb cables from the input might have been incorrectly connected to the input. Please make sure the input source has been correctly connected to the projector. The temperature inside the projector might have risen. When the temperature inside the projector rises, the cooling fan will operate at a higher speed to discharge the internal heat more rapidly. The LED indicator on the projector’s front panel is blinking in red. The lamp or the cooling fan could be faulty. Refer to the definition of page 26: Status lights of LED. 1. During projection, the lamp suddenly goes off and the picture disappears. The lamp might have been damaged; check The lamp has reached the end of its service the LED indicator on the rear panel of the life; please replace it. projector and see if it is blinking in red. The noise from the cooling fan suddenly grew louder. 2.The lamp does not turn on even when the projector has been turned on. 64 PFWX-51B/PFWU-51B 10/02/2014 11.Projector Specification 11. PROJECTOR SPECIFICATION 11.1 PFWU-51B Specifications Description Specifications Projector type Single-chip DLP projector Technology 0.67" DMD Color Wheel 5-segment (RGBWY) Brightness* 4650 ANSI lumen Brightness (eco-mode)* 3450 ANSI lumen Resolution WUXGA 1920 × 1200 Micro display DLP 0.67" DMD Contrast ratio 1800 : 1 Brightness uniformity ANSI 0.85% Aspect Ratio 67% Lens type F LENS Lamp 1 x 370W P-VIP Lamp lifetime (ECO/Bright) 3500/1500 Transport with lamp Yes Orientation table - ceiling Integrated web server Yes 3D Yes Keystone Correction ±40° Vertical Ease of Use Simplified OSD menu + Remote control Input Resolutions Up to WUXGA (1920x1200) 60Hz Software tools Projection Toolset Control IR; RS232; RJ45 Network connection 10/100 Base-T, RJ-45 connection Projection lens - projection ratio • R9832757: F lens (1.54-1.93:1, 1.25X) • R9832758: F lens (0.77:1 FIX) • R9832759: F lens (1.93-2.89:1, 1.5X) Horizontal Lens Shift Range -10%~+10% Vertical Lens Shift Range -30%~+110% Input/Output ports 1 x HDMI 1 x DVI-D 1 x DISPLAYPORT 2 x VGA IN 1 x VGA OUT 1 x RGBHV 1 x YUV 1 x S-VIDEO 1 x VIDEO 1 x RJ-45 1 x 3D SYNC OUT Power requirements AC Input 100V - 240V (±10%) (auto ranging) Power consumption in Bright mode 480W@100V/460W@240V Power consumption in ECO mode 365W@100VAC/355W@240VAC Power consumption in standby mode <0.5W PFWX-51B/PFWU-51B 10/02/2014 65 11.Projector Specification Description Specifications Noise level Bright mode (typical at 25°C/77°F) 42dBA Noise level ECO mode (typical at 25°C/77°F) 37dBA Operational ambient temperature 5-35°C or 41-95°F Operating humidity 10-85% Dimensions (WxLxH) 460mmX446mmX209mm Weight ±12kg (±26.5 lb.) Shipping Dimensions 594X568X355mm Shipping Weight from Factory 16.8kg CB test certificate US emc Certifications US safety CE emc and safety CCC emc and safety Warranty 3 years standard warranty** (*) Measurement, measuring conditions, and method of notation all comply with ISO 21118 international standards. (**) Warranty and service conditions can differ from region to region. Contact your local sales or service representative for more details. 66 PFWX-51B/PFWU-51B 10/02/2014 11.Projector Specification 11.2 PFWX-51B Specifications Description Specifications Projector type Single-chip DLP projector Technology 0.65" DMD Color Wheel 5-segment (RGBWY) Brightness* 4750 ANSI lumen Brightness (eco-mode)* 3300 ANSI lumen Resolution WXGA 1280 x 800 Micro display DLP 0.65" DMD Contrast ratio 1800 : 1 Brightness uniformity ANSI 0.85 Aspect Ratio 67% Lens type F LENS Lamp 1 x 370W P-VIP Lamp lifetime (ECO/Bright) 3500/1500 Transport with lamp Yes Orientation table - ceiling Integrated web server Yes 3D Yes Keystone Correction ±40° Vertical Ease of Use Simplified OSD menu + Remote control Input Resolutions Up to WUXGA (1920x1200) 60Hz Software tools Projection Toolset Control IR; RS232; RJ45 Network connection 10/100 Base-T, RJ-45 connection Projection lens - projection ratio • R9832757: F lens (1.62-2.03:1, 1.25X) • R9832758: F lens (0.81:1 FIX) • R9832759: F lens (2.02-3.03:1, 1.5X) Horizontal Lens Shift Range -10%~+10% Vertical Lens Shift Range -30%~+110% Input/Output ports 1 x HDMI 1 x DVI-D 1 x DISPLAYPORT 2 x VGA IN 1 x VGA OUT 1 x RGBHV 1 x YUV 1 x S-VIDEO 1 x VIDEO 1 x RJ-45 1 x 3D SYNC OUT Power requirements AC Input 100V - 240V (±10%) (auto ranging) Power consumption in Bright mode 480W@100V/460W@240V Power consumption in ECO mode 365W@100VAC/355W@240VAC Power consumption in standby mode <0.5W Noise level Bright mode (typical at 25°C/77°F) 42dBA PFWX-51B/PFWU-51B 10/02/2014 67 11.Projector Specification Description Specifications Noise level ECO mode (typical at 25°C/77°F) 37dBA Operational ambient temperature 5-35°C or 41-95°F Operating humidity 10-85% Dimensions (WxLxH) 460mmX446mmX209mm Weight ±12kg (±26.5 lb.) Shipping Dimensions 594X568X355mm Shipping Weight from Factory 16.8kg CB test certificate US emc Certifications US safety CE emc and safety CCC emc and safety Warranty 3 years standard warranty** (*) Measurement, measuring conditions, and method of notation all comply with ISO 21118 international standards. (**) Warranty and service conditions can differ from region to region. Contact your local sales or service representative for 68 PFWX-51B/PFWU-51B 10/02/2014 11.Projector Specification more details. 11.3 Standard Source Files The unit automatically determines PC signals to select the appropriate resolution Some signals may require manual adjustment. Signal Resolution H-SYNC (KHz) V-SYNC (Hz) NTSC PAL/SECAM 640 x 400 # 720 x 400 # 720 x 400 640 x 480 640 x 480 640 x 480 640 x 480 800 x 600 * 800 x 600 800 x 600 800 x 600 800 x 600 ** 800 x 600 1024 x 576 1024 x 600 1024 x 600 * 1024 x 768 1024 x 768 1024 x 768 1024 x 768 ** 1024 x 768 1024 x 768 1152 x 864 * 1280 x 720 * 1280 x 720 1280 x 768 * 1280 x 768 * 1280 x 800 1280 x 800 1280 x 800 ** 1280 x 800 *** 1280 x 1024 1280 x 1024 #1280 x 1024 *** 1280 x 960 1280 x 960 *** 1360 x 768 *** 1400 x 1050 1440 x 900 *** 1440 x 900 1440 x 900 ## 1600 x1200 ## 1680 x 1050 ## 1680 x 1050 ## 1920 x 1200 ## 1920 x 1080 15.734 15.625 37.9 31.5 37.9 31.5 37.9 37.5 43.3 35.2 37.9 46.9 48.1 53.7 76.3 35.8 37.3 41.5 48.4 56.5 60 68.7 97.6 99 67.5 45 90 47.4 47.8 49.7 62.8 71.6 101.6 64 80 91.1 60 85.9 47.7 65.3 55.5 55.9 70.6 75 64.7 65.3 74 67.5 PC PFWX-51B/PFWU-51B 10/02/2014 60 50 85.08 70.1 85.04 60 72.8 75 85 56.3 60.3 75 72.2 85.1 120 60 60 65 60 70.1 75 85 120 120 75 60 120 60 59.9 59.8 74.9 84.9 119.9 60 75 85 60 85 60 60 59.9 59.9 75 60 59.9 60 60 60 COMPOSITE S_VIDEO ¡ ¡ - COMPONENT - RGB (Analog) ¡ ¡ ¡ ¡ ¡ ¡ ¡ ¡ ¡ ¡ ¡ ¡ ¡ ¡ ¡ ¡ ¡ ¡ ¡ ¡ ¡ ¡ ¡ ¡ ¡ ¡ ¡ ¡ ¡ ¡ ¡ ¡ ¡ ¡ ¡ ¡ ¡ ¡ ¡ ¡ ¡ ¡ ¡ ¡ ¡ ¡ DP/HDMI (Digital) ¡ ¡ ¡ ¡ ¡ ¡ ¡ ¡ ¡ ¡ ¡ ¡ ¡ ¡ ¡ ¡ ¡ ¡ ¡ ¡ ¡ ¡ ¡ ¡ ¡ ¡ ¡ ¡ ¡ ¡ ¡ ¡ ¡ ¡ ¡ ¡ ¡ ¡ ¡ ¡ ¡ ¡ ¡ ¡ ¡ ¡ 69 11.Projector Specification Signal Resolution H-SYNC (KHz) V-SYNC (Hz) 640 x 480 832 x 624 Apple Macintosh 1024 x 768 ## 1152 x 870 ## 480i SDTV ## 576i ## 576p EDTV ## 480p ## 720p ## 720p ## 1080i ## 1080i HDTV ## 1080p ## 1080p ## 1080p ## 1080p ## 1080p 35 49.7 60.2 68.7 15.734 15.625 31.3 31.5 37.5 45 33.8 28.1 27 28 33.7 56.3 67.5 COMPOSITE S_VIDEO 66.7 74.5 74.9 75.1 60 50 50 60 50 60 60 50 24 25 30 50 60 COMPONENT - ¡ ¡ ¡ ¡ ¡ ¡ ¡ ¡ ¡ ¡ ¡ ¡ ¡ RGB (Analog) ¡ ¡ ¡ ¡ - DP/HDMI (Digital) ¡ ¡ ¡ ¡ ¡ ¡ ¡ ¡ ¡ ¡ ¡ ¡ ¡ ¡ ¡ ¡ ¡ ¡: Supported frequency -: Not Supported frequency • "#" It means Displayable only. (4:3 only). • "##" It means may have a little noise is acceptable, Because video mode sync don’t auto adjustment. *3D note: • “*” It means the timing can support non-3D and 3D signal with Frame Sequential and Top-Bottom format. • “**” It means the timing can support non-3D and 3D signal with Frame Sequential format. • “***” It means the timing can support non-3D and 3D signal with Top-Bottom format. There 3D timing showing depend the EDID file and display card. It is possible that user cannot choose the above 3D timings on display card. Table of Supported Frequency For 3D mode in detailed The unit automatically determines PC signals to select the appropriate resolution. Some signals may require manual adjustment. Input Signal for D-SUB Signal SVGA XGA HDTV (720p) Resolution 800 x 600 1024 x 768 1280 x 720 Refresh Rate (Hz) 60/120 60/120 60/120 Input Signal for HDMI/DVI-D Signal SVGA XGA WSVGA (1024 x 600) HDTV (720p) Resolution 800 x 600 1024 x768 1024 x 600 1280 x 720 Refresh Rate (Hz) 60/120 60/120 60 60/120 True 3D Video Compatibility table 70 PFWX-51B/PFWU-51B 10/02/2014 11.Projector Specification Input Resolutions HDMI 1.4a 3D Input HDMI 1.3 Input timing 1280 x 720P @ 50Hz 1280 x 720P @ 60Hz 1280 x 720P @ 50Hz 1280 x 720P @ 60Hz 1920 x 1080i @50 Hz 1920 x 1080i @60 Hz 1920 x 1080P @24 Hz 1920 x 1080P @24 Hz 1920 x 1080i @ 50Hz 1920 x1080i @ 60Hz 1280 x 720P @50Hz 1280 x 720P @60Hz 1920 x 1080i @ 50Hz 1920 x1080i @ 60Hz 1280 x 720P @50Hz 1280 x 720P @60Hz 480i Top - and - Bottom Top - and - Bottom Frame packing Frame packing Side- by-Side (Half) Side- by-Side (Half) Top - and - Bottom Frame packing Side-by-Side(Half) SBS mode is on Top-and-Bottom TAB mode is on HQFS 3D format is Frame sequential *Please make sure your 3D glasses has 144hz function. *The native resolution of the panel is 1280 x 800 (for WXGA)/1920 x 1200(for WUXGA). Resolution others than native resolution may be display with uneven size of text or line. *HDTV timing main check tool is DVD player, VG828 is secondary. PFWX-51B/PFWU-51B 10/02/2014 71 11.Projector Specification 11.4 Dimension 453.00 mm 460.55mm 446.00 208.60 72 PFWX-51B/PFWU-51B 10/02/2014 12.Environmental Information 12. ENVIRONMENTAL INFORMATION 12.1 Disposal information Disposal Information Waste Electrical and Electronic Equipment This symbol on the product indicates that, under the European Directive 2002/96/EC governing waste from electrical and electronic equipment, this product must not be disposed of with other municipal waste. Please dispose of your waste equipment by handing it over to a designated collection point for the recycling of waste electrical and electronic equipment. To prevent possible harm to the environment or human health from uncontrolled waste disposal, please separate these items from other types of waste and recycle them responsibly to promote the sustainable reuse of material resources. For more information about recycling of this product, please contact your local city office or your municipal waste disposal service. For details, please visit the Barco website at: http://www.barco.com/en/AboutBarco/weee Disposal of batteries in the product This product contains batteries covered by the Directive 2006/66/EC which must be collected and disposed of separately from municipal waste. If the battery contains more than the specified values of lead (Pb), mercury (Hg) or cadmium (Cd), these chemical symbols will appear below the crossed-out wheeled bin symbol. By participating in separate collection of batteries, you will help to ensure proper disposal and to prevent potential negative effects on the environment and human health. Mercury Notice Hg LAMP CONTAINS MERCURY, DISPOSE ACCORDING TO STATE/LOCAL LAW. This Barco product consists of materials that may contain mercury, which must be recycled or disposed of in accordance with local, state, or country laws: · Within this system, the lamp in the projector contains mercury. 12.2 Rohs compliance Turkey RoHS compliance Türkiye Cumhuriyeti: EEE Yönetmeli ine Uygundur. [Republic of Turkey: In conformity with the EEE Regulation] 中国大陆 RoHS (Information for China ROHS compliance) 根据中国大陆《电子信息产品污染控制管理办法》( 也称为中国大陆 RoHS),以下部份列出了本产品中可能包 含的有毒有害物质或 元 素的名称和含量。 Table of toxic and hazardous substances/elements and their content, as required by China’s management methods for controlling pollution by electronic information products. PFWX-51B/PFWU-51B 10/02/2014 73 74 "X" ( ( ( , , ) “ ) ) RoHS O O X O O O O O O O O O O O X X X X X X O O X X X X X X ROHS Hg Pb O O O O O O X X O O O O O O O O O O O O O O O O O O O Cr(VI) RoHS ( SJ/T11363-2006 O SJ/T11363-2006 Cd O O O O O O O O O O O O O O PBB O O O O O O O O O O O O O O ), PBDE 12.Environmental Information 本产品中包含的有毒有害物质/成分的名称和含量。 PFWX-51B/PFWU-51B 10/02/2014 12.Environmental Information 12.3 Production address Factories Barco nv Entertainment Division Noordlaan 5, B-8520 Kuurne Phone: +32 56.36.82.11 Fax: +32 56.36.883.86 Support: www.barco.com/esupport Visit us at the web: www.barco.com PFWX-51B/PFWU-51B 10/02/2014 75
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.7 Linearized : No Tagged PDF : Yes XMP Toolkit : Adobe XMP Core 5.4-c005 78.147326, 2012/08/23-13:03:03 Create Date : 2014:10:07 09:10:24+08:00 Metadata Date : 2014:10:07 09:11:40+08:00 Modify Date : 2014:10:07 09:11:40+08:00 Creator Tool : Adobe InDesign CS6 (Windows) Instance ID : uuid:422a5ea6-b81a-417e-b2e2-cdbf8895c4b4 Original Document ID : xmp.did:78152C0204C8E211AC278CDBD9C43915 Document ID : xmp.id:1D291AABBE4DE4118603B849EF683CB3 Rendition Class : proof:pdf Derived From Instance ID : xmp.iid:1C291AABBE4DE4118603B849EF683CB3 Derived From Document ID : xmp.did:1C291AABBE4DE4118603B849EF683CB3 Derived From Original Document ID: xmp.did:78152C0204C8E211AC278CDBD9C43915 Derived From Rendition Class : default History Action : converted History Parameters : from application/x-indesign to application/pdf History Software Agent : Adobe InDesign CS6 (Windows) History Changed : / History When : 2014:10:07 09:10:24+08:00 Format : application/pdf Producer : Adobe PDF Library 10.0.1 Trapped : False Page Layout : SinglePage Page Mode : UseOutlines Page Count : 82 Creator : Adobe InDesign CS6 (Windows)EXIF Metadata provided by EXIF.tools