Beats Electronics 81000057 Portable Stereo Sound System User Manual Pill UserGuide 071812 REV4

Beats Electronics, LLC Portable Stereo Sound System Pill UserGuide 071812 REV4

User manual

BeatsPill Active Ingredients: (Portable Stereo Bluetooth Speaker)8.5HR EN 1. POWER ON/OFFTo Turn on BeatsPill, firmly press and release the power button, the Beats logo will light and after a brief startup period, an audio cue will indicate the system is on. To turn Beatspill off, firmly press and release the power button. The Beats logo will fade out and an audio cue will indicate power off.2. CONNECTEDTo pair Beatspill with a compatible bluetooth device for A2DP (stereo audio) and/or HFP (phone calls), press and hold the rear power button for a full 5 sec. The rear BT LED will blink WHITE rapidly, indicating that Beatspill is in pairing mode and is discoverable by a source device. Pairing mode can be cancelled by pressing the power button. Beatspill will remain in pairing mode for approx. 3 minutes. If no pair is achieved, it will enter an unconnected state and pairing mode must be reinitiated.ConnectedWhen Beatspill is successfully paired and connected to a Bluetooth device, the rear BT LED will be solid WHITE. When Beatspill is not connected to any BT device, the rear BT LED will be unlit. Beatspill can remember up to eight paired devices in its memory and will automatically try to connect with the most recently connected device , however, HFP (telephone) devices will take priority over stereo audio devices when Beatspill searches for an auto connection. StealingIf Beatspill is paired to two or more compatible devices and automatically connects to a non-preferred device, you can “steal” the connection with your preferred device by selecting “beatspill” in your devices BT list IMPORTANT SAFETY INFORMATION1. READ these instructions.2. KEEP these instructions.3. HEED all warnings.4. FOLLOW all instructions.5. DO NOT use this apparatus near water.6. CLEAN ONLY with dry cloth.7. DO NOT block any ventilation openings.Install in accordance with the manufacturer’s instructions.8. DO NOT install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.9. PROTECT the power cord from being walked on or pinched, particularly at the plugs and the point where it exits from the apparatus.10. ONLY USE attachments/accessories specified by the manufacturer.11. UNPLUG this apparatus during lightning storms or when unused for long periods of time.12. DO NOT expose this apparatus to dripping or splashing and ensure that no objects filled with liquids, such as vases, are placed on the apparatus.13. To completely disconnect this apparatus from the AC mains, disconnect the power supply cord plug from the AC receptacle.14. The mains plug of the power supply cord shall remain readily operable.and initiating a connection.3. AUX INPUTTo play audio using the supplied 3.5mm cable, simply plug the cable into the music source device into the “audio in” jack on the Beatspill. 4. AUDIO OUTThe audio output of the Beatspill can be used to connect to the line in of an alternate audio system, such as a home theater, or BeatsbyDre Beatbox. This allows the pill to act as a Bluetooth receiver for audio playback devices that do not have Bluetooth capability. When audio out jack is used, the Beatspill internal speakers will be disabled and the volume controls are also inactive. When a phone call is received while also using the audio out, audio out will be temporarily disabled and phone call functionality will be enabled on the Beatspill.5. VOLUMEWhen using BT or Aux in as the audio source, the Beatspill volume can be adjusted with the volume up and down buttons on the front top surface of the Beatspill. To quickly adjust the volume, press and hold the up or down volume button. *Volume buttons are disabled when Audio out is used.6. BLUETOOTH CONTROLSAudio play and pauseWhen listening to stereo audio wirelessly thru a connected bluetooth device (A2DP) music can be paused and un-paused by pressing the front B logo multifunction button (MFB). Phone CallsBeatspill can be used to make and receive phone calls when connected to a HFP1.6 Bluetooth compatible handset. Audio playback will be paused when a phone call is in progress. To answer a call when connected to a BT compatible handset, press the front MFB. This will accept an incoming call. To Reject an incoming call, press and hold the MFB. To Hang up a call in progress, press the front MFB. To answer an incoming call when already on a call in progress: press the front MFB. This will answer the incoming call and put the current call on hold. To Reject an incoming call when already on a call in progress: press and hold the MFB. This will reject the incoming call and current call will remain active. To switch between an active call and a call on hold: press the front MFB. Pressing again will switch back to the previous call. To Switch the audio output back to the handset instead of Beatspill: press the MFB twice quickly when on an active call.7. CHARGING AND BATTERYTo charge the Beatspill, plug the USB cable into the rear USB port and into a USB compatible power supply/ source. Charging will be indicated by a solid RED ring around the USB port. When full charge is reached, the ring around the USB port will change to solid GREEN. Battery life should be approximately 8.5 hrs at moderate listening levels. When Beatspill detects that it has 20% battery life remaining and USB cable is unplugged, USB port will blink, indicating that power source should be connected.8. TECHNICAL SPECIFICATIONSWeight: 325gBattery Life: 8.5 hours (average at 80dB)Power Adapter Output Rating: 5Vdc, 2.1APower Adapter Input Rating: 100-240V ~ 50/60Hz, 0.5ABeatsPill Active Ingredients: (Portable Stereo Bluetooth Speaker)8.5HR EN 1. POWER ON/OFFTo Turn on BeatsPill, firmly press and release the power button, the Beats logo will light and after a brief startup period, an audio cue will indicate the system is on. To turn Beatspill off, firmly press and release the power button. The Beats logo will fade out and an audio cue will indicate power off.2. CONNECTEDTo pair Beatspill with a compatible bluetooth device for A2DP (stereo audio) and/or HFP (phone calls), press and hold the rear power button for a full 5 sec. The rear BT LED will blink WHITE rapidly, indicating that Beatspill is in pairing mode and is discoverable by a source device. Pairing mode can be cancelled by pressing the power button. Beatspill will remain in pairing mode for approx. 3 minutes. If no pair is achieved, it will enter an unconnected state and pairing mode must be reinitiated.ConnectedWhen Beatspill is successfully paired and connected to a Bluetooth device, the rear BT LED will be solid WHITE. When Beatspill is not connected to any BT device, the rear BT LED will be unlit. Beatspill can remember up to eight paired devices in its memory and will automatically try to connect with the most recently connected device , however, HFP (telephone) devices will take priority over stereo audio devices when Beatspill searches for an auto connection. StealingIf Beatspill is paired to two or more compatible devices and automatically connects to a non-preferred device, you can “steal” the connection with your preferred device by selecting “beatspill” in your devices BT list FCC STATEMENTFCC-ID: COW81000057This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:Reorient or relocate the receiving antenna.Increase the separation between the equipment and receiver.Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.Consult the dealer or an experienced radio/TV technician for help.FCC RADIATION EXPOSURE STATEMENTThis equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body.This equipment complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:(1) This device may not cause harmful interference, and(2) This device must accept any interference received, including interference that may cause undesired operation.CAUTIONThe manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void the user authority to operate the equipment.CANADA STATEMENTThis device complies with Industry Canada RSS-210. Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. The device meets the exemption from the routine evaluation limits in section 2.5 of RSS 102 and compliance with RSS-102 RF exposure, users can obtain Canadian information on RF exposure and compliance.IMPORTANT SAFETY INFORMATION The exclamation point, within an equilateral triangle, is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product. The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electrical shock.WARNING: To reduce the risk of fire or electrical shock, do not expose this apparatus to rain or moisture.WARNING: No naked flame sources – such as candles – should be placed on the product.WARNING: Batteries (battery pack or batteries installed shall not be exposed to excessive heat such as sunshine, fire or the like.Place the equipment near a main power supply outlet and make sure that you can easily access the power breaker switch.CAUTION: Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type.and initiating a connection.3. AUX INPUTTo play audio using the supplied 3.5mm cable, simply plug the cable into the music source device into the “audio in” jack on the Beatspill. 4. AUDIO OUTThe audio output of the Beatspill can be used to connect to the line in of an alternate audio system, such as a home theater, or BeatsbyDre Beatbox. This allows the pill to act as a Bluetooth receiver for audio playback devices that do not have Bluetooth capability. When audio out jack is used, the Beatspill internal speakers will be disabled and the volume controls are also inactive. When a phone call is received while also using the audio out, audio out will be temporarily disabled and phone call functionality will be enabled on the Beatspill.5. VOLUMEWhen using BT or Aux in as the audio source, the Beatspill volume can be adjusted with the volume up and down buttons on the front top surface of the Beatspill. To quickly adjust the volume, press and hold the up or down volume button. *Volume buttons are disabled when Audio out is used.6. BLUETOOTH CONTROLSAudio play and pauseWhen listening to stereo audio wirelessly thru a connected bluetooth device (A2DP) music can be paused and un-paused by pressing the front B logo multifunction button (MFB). Phone CallsBeatspill can be used to make and receive phone calls when connected to a HFP1.6 Bluetooth compatible handset. Audio playback will be paused when a phone call is in progress. To answer a call when connected to a BT compatible handset, press the front MFB. This will accept an incoming call. To Reject an incoming call, press and hold the MFB. To Hang up a call in progress, press the front MFB. To answer an incoming call when already on a call in progress: press the front MFB. This will answer the incoming call and put the current call on hold. To Reject an incoming call when already on a call in progress: press and hold the MFB. This will reject the incoming call and current call will remain active. To switch between an active call and a call on hold: press the front MFB. Pressing again will switch back to the previous call. To Switch the audio output back to the handset instead of Beatspill: press the MFB twice quickly when on an active call.7. CHARGING AND BATTERYTo charge the Beatspill, plug the USB cable into the rear USB port and into a USB compatible power supply/ source. Charging will be indicated by a solid RED ring around the USB port. When full charge is reached, the ring around the USB port will change to solid GREEN. Battery life should be approximately 8.5 hrs at moderate listening levels. When Beatspill detects that it has 20% battery life remaining and USB cable is unplugged, USB port will blink, indicating that power source should be connected.8. TECHNICAL SPECIFICATIONSWeight: 325gBattery Life: 8.5 hours (average at 80dB)Power Adapter Input Rating: 100-240V ~ 50/60Hz, 0.5A3.2.4.5. 6.7. 1.CutCutCutCutCutCutCutCutFoldFoldFoldFoldFoldFoldFold FoldFold FoldFoldFoldBEATSPILL USER GUIDE - xx196[7.716]49.4[1.945]27.5[1.082]526.5[20.73]172.5[6.791]49.4[1.945]49.4[1.945]49.4[1.945]154[6.063]172.5[6.791]FRONTLANGUAGE PANEL 1ILLUSTRATED INSTRUCTIONS FRONTLANGUAGE PANEL 2BlackFILE NAME:DIELINE:PROJECT:MANAGER:DESIGNER:VIEW:DESIGNER:AMENDED BY:REVISION:ARTWORK INFO:DIELINE INFO:REVISION:1500 Sansome Street, Roundhouse One, San Francisco, CA 94111 | 415.632.1170 | www.ammunitiongroup.comCLIENT: JOB NO: DATE:FINISHES:INKS USED:CUTCREASEBLEED07/12/2012Beats LLCPill_UserGuide_071212.aixxBeatsPill User GuideHamish ThainKatie King Rumford Katie King RumfordFront Hamish Thainxxxx01 01CLIENT REF:N/A:05Power Adapter Output Rating: 5Vdc, 2.1A

Navigation menu