Behringer Digital Pro Mixer Ddm4000 Users Manual DIGITAL_PRO_MIXER_DDM4000

Behringer-Digital-Pro-Mixer-Ddm4000-Owners-Manual behringer-digital-pro-mixer-ddm4000-owners-manual

: Behringer Behringer-Digital-Pro-Mixer-Ddm4000-Users-Manual-752240 behringer-digital-pro-mixer-ddm4000-users-manual-752240 behringer pdf

Open the PDF directly: View PDF .
Page Count: 32

User Manual

DIGITAL PRO MIXER DDM4000

Ultimate 5-Channel Digital DJ Mixer with Sampler,

4 FX Sections, Dual BPM Counters and MIDI

2DIGITAL PRO MIXER DDM4000 User Manual

Thank you

Herzlichen Glückwunsch! Mit dem DDM4000 besitzt Du einen DJ-Mixer, mit dem

Du Deiner Zeit weit voraus bist. Der DDM4000 ist ein erstklassiger digitaler 32-Bit

DJ Mixer mit zahlreichen kreativen Funktionen, der jedoch dank einer intuitiven

Benutzeroberäche sofort leicht zu bedienen ist. Mit Funktionen wie Editieren,

Speichern und Aufrufen von Einstellungen bist Du sofort vertraut.

Table of Contents

Thank you .......................................................................2

Important Safety Instructions ...................................... 3

Legal Disclaimer ............................................................. 3

Limited warranty ............................................................ 3

1. Introduction ............................................................... 4

2. Controls and Connections ........................................ 5

3. Operation ................................................................. 11

4. BPM and Eects Section ......................................... 16

5. Sampler ....................................................................20

6. Further Settings.......................................................22

7. The DDM4000 as MIDI Controller ...........................23

8. Installation ...............................................................24

9. Specications ...........................................................25

10. Appendix ................................................................ 26

3DIGITAL PRO MIXER DDM4000 User Manual

Important Safety

Instructions

LEGAL DISCLAIMER

LIMITED WARRANTY

Terminals marked with this symbol carry

electrical current of su cient magnitude

to constitute risk of electric shock.

Use only high-quality professional speaker cables with

¼" TS or twist-locking plugs pre-installed. Allother

installation or modi cation should be performed only

by quali edpersonnel.

This symbol, wherever it appears,

alertsyou to the presence of uninsulated

dangerous voltage inside the

enclosure-voltage that may be su cient to constitute a

risk ofshock.

This symbol, wherever it appears,

alertsyou to important operating and

maintenance instructions in the

accompanying literature. Please read the manual.

Caution

To reduce the risk of electric shock, donot

remove the top cover (or the rear section).

No user serviceable parts inside. Refer servicing to

quali ed personnel.

Caution

To reduce the risk of  re or electric shock,

do not expose this appliance to rain and

moisture. The apparatus shall not be exposed to dripping

or splashing liquids and no objects  lled with liquids,

suchas vases, shall be placed on the apparatus.

Caution

These service instructions are for use

by quali ed service personnel only.

Toreduce the risk of electric shock do not perform any

servicing other than that contained in the operation

instructions. Repairs have to be performed by quali ed

servicepersonnel.

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with dry cloth.

7. Do not block any ventilation openings. Install in

accordance with the manufacturer’s instructions.

8. Do not install near any heat sources such as

radiators, heat registers, stoves, or other apparatus

(including ampli ers) that produce heat.

9. Do not defeat the safety purpose of the polarized

or grounding-type plug. A polarized plug has two blades

with one wider than the other. A grounding-type plug

has two blades and a third grounding prong. The wide

blade or the third prong are provided for your safety. Ifthe

provided plug does not  t into your outlet, consult an

electrician for replacement of the obsolete outlet.

10. Protect the power cord from being walked on or

pinched particularly at plugs, convenience receptacles,

and the point where they exit from the apparatus.

11. Use only attachments/accessories speci ed by

themanufacturer.

12. Use only with the

cart, stand, tripod, bracket,

or table speci ed by the

manufacturer, orsold with

the apparatus. When a cart

is used, use caution when

moving the cart/apparatus

combination to avoid

injury from tip-over.

13. Unplug this apparatus during lightning storms or

when unused for long periods of time.

14. Refer all servicing to quali ed service personnel.

Servicing is required when the apparatus has been

damaged in any way, such as power supply cord or plug

is damaged, liquid has been spilled or objects have fallen

into the apparatus, the apparatus has been exposed

to rain or moisture, does not operate normally, or has

beendropped.

15. The apparatus shall be connected to a MAINS socket

outlet with a protective earthing connection.

16. Where the MAINS plug or an appliance coupler is

used as the disconnect device, the disconnect device shall

remain readily operable.

TECHNICAL SPECIFICATIONS AND APPEARANCES

ARE SUBJECT TO CHANGE WITHOUT NOTICE AND

ACCURACY IS NOT GUARANTEED. BEHRINGER,

KLARKTEKNIK, MIDAS, BUGERA, AND TURBOSOUND

ARE PART OF THE MUSIC GROUP MUSICGROUP.COM.

ALL TRADEMARKS ARE THE PROPERTY OF THEIR

RESPECTIVE OWNERS. MUSICGROUP ACCEPTS NO

LIABILITY FOR ANY LOSS WHICH MAY BE SUFFERED

BY ANY PERSON WHO RELIES EITHER WHOLLY OR

IN PART UPON ANY DESCRIPTION, PHOTOGRAPH

OR STATEMENT CONTAINED HEREIN. COLORS AND

SPECIFICATIONS MAY VARY FROM ACTUAL PRODUCT.

MUSIC GROUP PRODUCTS ARE SOLD THROUGH

AUTHORIZED FULLFILLERS AND RESELLERS ONLY.

FULLFILLERSAND RESELLERS ARE NOT AGENTS OF

MUSICGROUP AND HAVE ABSOLUTELY NO AUTHORITY

TO BIND MUSICGROUP BY ANY EXPRESS OR IMPLIED

UNDERTAKING OR REPRESENTATION. THIS MANUAL

IS COPYRIGHTED. NO PART OF THIS MANUAL MAY

BE REPRODUCED OR TRANSMITTED IN ANY FORM

OR BY ANY MEANS, ELECTRONIC OR MECHANICAL,

INCLUDING PHOTOCOPYING AND RECORDING OF ANY

KIND, FOR ANY PURPOSE, WITHOUT THE EXPRESS

WRITTEN PERMISSION OF MUSICGROUPIPLTD.

ALL RIGHTS RESERVED.

© 2013 MUSICGroupIPLtd.

Trident Chambers, Wickhams Cay, P.O. Box 146,

Road Town, Tortola, British Virgin Islands

For the applicable warranty terms and conditions

and additional information regarding MUSIC Group’s

Limited Warranty, please see complete details online at

www.music-group.com/warranty.

4DIGITAL PRO MIXER DDM4000 User Manual

1. Introduction

Hook up your turntables and CD/MP3 players to its 4 stereo channels,

each with fully programmable EQ and Kill switches. Put ultimate versatility

at your ngertips with fully programmable beat-sync’able multi-FX modules,

a pair of high-precision BPM counters and a digital crossfader with custom

curve adjustment. And the super-cool BPM-sync’d sampler with real-time pitch

control, loop and reverse functions will make your crowd go wild.

◊ Please read this manual to familiarize yourself with the control

elements of the unit and its functions. After you have carefully

read this manual, keep it for future reference.

1.1 Before you get started

1.1.1 Shipment

Your DDM4000 was carefully packed at the factory, and the packaging

was designed to protect the unit from damage caused by rough handling.

Nevertheless, we recommend that you carefully examine the packaging and its

contents for any signs of physical damage that may have occurred during transit.

◊ If the unit is damaged, please do NOT return it to us; instead,

notify your dealer and the shipping company immediately,

otherwise claims for damage or replacement may not be granted.

◊ We recommend using a case to ensure optimal protection of the device.

◊ Please always use the original packaging to avoid damage due to

storage or shipping.

◊ Never let unsupervised children play with the DDM4000 or

with its packaging.

◊ Recycle whenever possible.

1.1.2 Initial operation

Ensure adequate air supply and to avoid overheating do not place the unit

near radiators etc.

◊ Before you connect your DDM4000 to the mains, please make sure

that your local voltage matches the voltage required by the unit.

Caution! The following applies only to units that can be switched between

120 V and 230 V: The fuse holder on the mains connector has 3 triangular

markings, with two of these triangles opposing each other. The DDM4000 is set

to the operating voltage printed next to these markers and can be set to another

voltage by turning the fuse holder by 180°.

◊ Please note that when operating the unit at 120 V, a higher fuse rating

is required. Please refer to the “Specifications” for details.

◊ If you set the unit to a different mains voltage, be sure to use a fuse

of the correct type and rating. Please refer to the “Specifications”

for details.

◊ Blown fuses must be replaced by fuses of the same type and rating!

Please refer to the “Specifications” for details.

 Caution!

◊ Before changing the fuse, switch off the device and pull the plug to

avoid electric shock or damage to the device.

The DDM4000 power connection is made by using the enclosed cable and

the amplier’s standard IEC receptacle. It meets all of the international safety

certication requirements.

◊ Please make sure that all units have a proper earth connection. For your

own safety, never remove or disable the earth conductor from the unit

or of the AC power cord.

IMPORTANT NOTES CONCERNING INSTALLATION

◊ The sound quality may diminish within the range of powerful

broadcasting stations and high-frequency sources. Increase the

distance between the transmitter and the device and use shielded

cables for all connections.

1.1.3 Online registration

Please register your new BEHRINGER equipment right after your purchase

by visiting http://behringer.com and read the terms and conditions of our

warranty carefully.

Should your BEHRINGER product malfunction, it is our intention to have it

repaired as quickly as possible. To arrange for warranty service, please contact

the BEHRINGER retailer from whom the equipment was purchased. Should your

BEHRINGER dealer not be located in your vicinity, you may directly contact

one of our subsidiaries. Corresponding contact information is included in

the original equipment packaging (Global Contact Information/European

Contact Information). Should your country not be listed, please contact the

distributor nearest you. A list of distributors can be found in the support area of

our website (http://behringer.com).

Registering your purchase and equipment with us helps us process your repair

claims more quickly and eciently.

Thank you for your cooperation!

 Caution!

◊ Extreme output volumes may damage your hearing and/or

your loudspeakers. Turn down all volume and level controls before

you switch on the unit. Always set the volume to an appropriate level.

5DIGITAL PRO MIXER DDM4000 User Manual

Fig. 2.0: Overview of DDM4000

(2.1) (2.4)

(2.2)

(2.5)

(2.6)

(2.3)

(2.1)

(2.9)

(2.7)

(2.8)

2.1 Stereo channels 1 – 4

2.2 Microphone channel

2.3 Crossfader section

2.4 Main and phones section0

2.5 BPM and eects section

2.6 Sampler

2.7 Rear panel connectors

2.8 Rear panel outputs

2.9 Power section

2. Controls and Connections

This chapter describes the various controls and connections of the DDM4000 mixer. We have divided the console into several functional sections for a better overview.

6DIGITAL PRO MIXER DDM4000 User Manual

2.1 Stereo channels 1 – 4

(4)

(1)

(3)

(5)

(6)

(9)

(10)

(7)

(8)

(2)

Fig. 2.1: Stereo channel strips

(1) The input select switch lets you switch between two signal sources.

Select Line to hear the signal of the Line input (67). Select Phono/Line to

listen to the incoming source signal at the Phono/Line (68) input.

(2) The GAIN knob adjusts the level of the input signal. The actual level

is displayed on the level meter (3).

(3) The 7-segment LED meter indicates the level of the input signal.

(4) Each input channel features a 3-band equalizer (HIGH, MID and LOW)

with kill feature, giving you up to 12 dB of boost and a maximum cut

of -∞ dB (kill). The kill feature lets you mute the given frequency range.

When each EQ knob is turned fully left, the signal is eectively muted.

All EQ parameters can be adjusted in Channel Setup.

(5) The MODE push button changes the functionality of the preset push button

(6) from Multi to Single.

(6) The preset push buttons P1, P2 and P3 allow you to store and activate

equalizer presets. When activated in Single Mode, these push buttons

provide a maximum cut of -∞ dB (kill function).

(7) Press the PFL push button to listen in on the channel’s signal

using headphones.

(8) The fader controls the channel volume.

(9) The CURVE switch adjusts the response of the fader. In SOFT Mode, the fader

responds slower to steady fader movement in the upper range and quicker in

the lower range. In Sharp Mode, the fader adjusts the volume quicker in the

upper third and slower in the lower range. In MID Mode, the fader responds

in a linear fashion. Since a dierence in volume levels is heard when

switching between modes, don’t use this switch while playing music!

(10) The CF ASSIGN push button lets you determine on which side of the

crossfader (20) (A or B the signal is to be heard.

2.2 Microphone channel

(11) (12)

(13)

(16)

(17)

(18)

(19)

(14)

(15)

Fig. 2.2: Microphone channel

(11) The GAIN knob adjusts the level of the microphone signal at the MIC 1 input.

(12) This switch determines which signal is to be displayed on the level meter (13).

IN VU shows the unprocessed input level which helps you to adjust the

microphone signal correctly. XMC VU shows the level after it has passed

the Ultramic processor.

(13) The 7-segment LED meter indicates the level of the microphone channel.

(14) The microphone channel strip features a 3-band equalizer

(HIGH, MID and LOW). The range is +/-12 dB.

(15) The ON/OFF push button turns the microphone channel on and o.

(16) The MIC SETUP push button opens the Mic Setup menu on the display.

This allows you to adjust the settings of the equalizer, the Ultramic processor

and the MIC FX (eects processor).

(17) The XMC ON push button activates the ULTRAMIC processor, which includes

a 2-band compressor and expander. Ultramic settings can be adjusted in

Mic Setup.

(18) The MIC FX ON push button activates the microphone eects processor.

Select the eect in Mic Setup.

(19) The TALK ON push button activates the Talkover function. This attenuates

the volume level of the music as soon as you speak into the microphone.

This is a very useful function to make yourself heard over the music

being played. You can adjust all the relevant settings in Talk Setup.

7DIGITAL PRO MIXER DDM4000 User Manual

2.3 Crossfader section

(26)

(29)

(25)

(24)

(21)(23)

(22)

(20)

(28)

(27)

Fig. 2.3: Crossfader section

(20) The replaceable crossfader is used to fade between the signals that are

assigned to its two sides A and B. You can assign the stereo channels and

sampler using the CF Assign push buttons (10) and (65).

(21) The CF ON push button activates the crossfader. When the push button is

not pressed, the signals of the individual channels are routed straight to the

Main outputs.

(22) There are 3 Kill push buttons (HIGH, MID and LOW) on each side of the

crossfader which let you mute the given frequency range. In Crossfader

Setup (see Chapter 3.4.2), it is possible to activate a special X-OVER mode

that enhances the crossfader’s functionality in combination with the

Kill push buttons. For more information, read Chapter 3.4.1.

(23) Press the FULL FREQ push button to remove any frequency cuts of

the KILL EQ (22).

(24) The CURVE knob lets you seamlessly adjust the response of the crossfader.

The REVERSE function allows you to reverse the conguration of the crossfader.

This way you can toggle between Channel A and B at the ick of a switch

(25) REVERSE HOLD activates a permanent Reverse function. The crossfader

fades between sides A and B in the reverse direction. This means that A

is now on the right and B on the left side.

(26) REVERSE TAP activates a momentary Reverse function. This means that

A and B are interchanged as long as the TAP push button is held down.

The BOUNCE TO MIDI CLOCK function provides an automatic, quick crossfading

synchronized to the rhythm of the music (“bouncing”). The bounce speed is

determined by the MIDI Clock.

(27) Press the BOUNCE TO MIDI CLK push button to activate the bouncing.

Once the push button is pressed, the signal repeatedly jumps from A to B

and back again corresponding to the interval pre-selected by using the

BEAT push buttons (28).

(28) The BEAT push buttons let you determine the Bounce rate, which can range

between one and 16 beats.

(29) These LEDs indicate the number of beats you have chosen.

◊ Find a detailed description of this function in Chapter 3.4.3.

2.4 Main and phones section

(36)

(35)

(32)

(31)

(30)

(37)

(38)

(40)

(39)

(34)

(33)

Fig. 2.4: Main and Phones section

MAIN OUTPUT:

(30) The OUTPUT A knob controls the volume of output A ( (73) ).

(31) The BALANCE knob adjusts the stereo panning of output A.

(32) The OUTPUT B knob controls the volume of output B ( (74)).

(33) The high-resolution, 22-segment OUTPUT LEVEL meter indicates

the level of the output signal on OUTPUT A.

(34) ULTRAMIZE ON/OFF push button: The Ultramizer is an eect that

enhances the loudness and assertiveness by dynamic compression.

In Ultramizer Setup (see Chapter 3.5.1), you can congure the Ultramizer.

(35) The LOAD push button lets you load the user settings of the entire mixer.

The settings that are active when the device is turned o are loaded when

the device is switched back on again. Read more about saving and loading

user settings in Chapter 3.5.2.

PHONES:

(36) Connect the headphones to the PHONES jack (¼" TRS connector).

(37) The OUTPUT knob controls the volume of the head-phones.

(38) The MIX knob adjusts the balance between PFL signal and

PGM signal (PFL = Pre Fader Listening, fader independent pre-listening

of individual channels; PGM = Program, Master signal). When the

knob is turned completely to the left, you only hear the PFL signal,

whereas when turned completely to the right the Master signal is heard.

Between these two positions, you can adjust the mix of both signals.

(39) The PUNCH EQ function helps synchronize two tracks. You can orient

yourself to the snare or the bass drum or both. Press the SNARE or

BASS push button to emphasize the selected sound in the headphones.

(40) When the SPLIT push button is pressed, the PFL signal is heard in the

left headphone and the PGM signal is only heard in the right headphone.

8DIGITAL PRO MIXER DDM4000 User Manual

2.5 BPM and eects section

(41) (46) (47) (48) (51)

(50)

(45)

(50)

(42) (49) (43) (52)(53)

Fig. 2.5: BPM Counter and Eects section (here FX 1)

The DDM4000 has 2 identical eects units. There are 2 additional independent

eects units for the mic signal and the Sampler. All eects can be used at the

same time. The BPM Counter and MIDI Clock are also found in this section.

(41) The graphic display shows BPM values, eect names and eect parameters

as well as channel assignments. It also leads you through Console Setup.

(42) The FX ON push button activates the eects unit.

(43) Press the FX ASSIGN push button to assign an eects unit to a

signal source (push button ashes). The possible input sources are listed

on the display. Select the preferred source by turning and pressing the

PARAMETER knob (45).

(44) The DEPTH knob adjusts the eect intensity (depth). For some eects,

it also lets you adjust the mix between the original signal (dry) and

the eect signal (wet).

(45) Press the PARAM (eter) knob to select the eect parameters. By turning

the knob, you can change the parameter shown on the display.

(46) Press SELECT/LOW to access the eects list (on the display). Turn and press

the knob (45) to load a preset.

(47) Press the PARAM/MID push button to access the eect parameters.

Turn the knob (45) to change the parameter value.

(48) Press DEFAULT/HIGH to restore a preset.

◊ When the effect is activated (by pressing the FX ON push button),

the push buttons (46) (LOW), (47) (MID) and (48) (HIGH) are used as

Kill switches in the effect’s signal path.

(49) Depending on the selected eect, the BEAT push buttons can adjust

time-related parameters. However, the values entered are not in

milliseconds or similar units, but in beats.

(50) To enter the tempo manually, tap this push button (at least 2 x) in the rhythm

of the music (TAP). By keeping the AUTO BPM/TAP push button pressed a

little longer (> 1 s), the automatic tempo input (AUTO BPM) is reactivated.

(51) Turn the CONSOLE SETUP knob to adjust the tempo of the MIDI Clock

(press and turn simultaneously = coarse adjustment). A short press on

the knob conrms the entry made. A long press on the knob lets you

access Console Setup (see Chapter 3.1).

(52) The MIDI START/STOP/ESC turns on the MIDI Clock.

(53) The ADJUST push buttons let you transfer the tempo of the BPM counter

to the MIDI Clock.

◊ All functions of the BPM and Effects section are described in

detail in Chapter 4.

2.6 Sampler

(54)(54)

(57)

(59)

(63)

(65)

(62)

(56)

(60)

(64)

(66)

(61)

(58)

Fig. 2.6: Sampler section

(54) Press the INSERT push button to add the sampler signal to the channel

(Insert Mode). If the push button is not activated, the sampler is mixed to

the selected channel (Mix Mode). In both cases, playback is initiated with

the REC SOURCE push buttons. When the sampler is routed to the crossfader,

the LED of the INSERT push button goes out.

(55) The VOLUME/MIX knob controls the volume of the sampler (in Mix Mode)

as well as the volume balance between input signal and Sampler

(in Insert Mode).

(56) The REC SOURCE push buttons let you select the channel for recording

and playing back samples.

(57) Press the PFL push button to listen in on the sampler signal with the headphones.

(58) SAMPLE LENGTH adjusts the recording time (1–16 beats or endless recording ∞).

(59) RECORD/IN lets you record to the Sampler. Select a bank beforehand.

By pressing the push button a second time, the recording is stopped

(only in ∞ Mode).

(60) BANK ASSIGN is used to select a bank in which the recorded material

is stored. The selected bank is indicated by the relevant MODE push button

(61) which signalizes the readiness to record.

(61) The MODE push buttons (Bank 1 and Bank 2) are used to select the sampler’s

types of playback (Reverse and Loop). A short tap activates or deactivates

the Reverse function; pressing the push button a little longer activates or

deactivates the Loop function.

(62) Press the PLAY/OUT push button to start the playback of the

recorded sample. When the Loop function is deactivated, the sample is

only played back as long as the PLAY push button is pressed.

(63) Press SMP FX ON push button to activate the Brake eect.

(64) Press the SELECT push button to determine the length of the brake

(1, 4 or 8 Beat Brake, which is shown in the center of the display).

(65) The CF ASSIGN push button lets you determine on which side of the

crossfader the sampler signal is to be routed to.

9DIGITAL PRO MIXER DDM4000 User Manual

(66) You can even trigger the sampler with the crossfader when the sampler

is assigned to it. To order to do so, simply press the CF START push button.

But beforehand, use BANK ASSIGN to select the bank that should be played

back when using the fader.

2.7 Rear panel connectors

(71)(72)(68)(67)(70)(69) (69)

Fig. 2.7: Rear panel connectors

(67) The LINE inputs are used to connect the Line signals

(for example, CD players, soundcards and drum machines).

(68) The PHONO inputs let you connect turntables.

(69) Use the PHONO/LINE switches to set the PHONO inputs to Line level

in order for you to be able to connect a CD player to the PHONO inputs.

◊ Caution! Devices with Line output levels, such as CD players,

can cause distortion and destroy the preamplifier. Press the

PHONO/LINE switch before connecting devices with Line level

to the highly sensitive PHONO inputs.

(70) The GND connectors are used to ground the turntables.

(71) The balanced XLR connectors provide a connection for dynamic microphones.

(72) This is the LEVEL control for the MIC 2 input.

2.8 Rear panel outputs

(73) (74) (75) (76)

Fig. 2.8: Rear panel connectors

(73) These are the OUT A outputs (XLR) allowing you to connect to

an amplier. Use the OUTPUT A control (30) to adjust the volume level.

Additionally, the SUBWOOFER output lets you hook up a subwoofer.

A crossover is integrated into the DDM4000. The crossover frequency

is adjusted in Output Setup (see Chapter 6.2).

◊ When powering up the system, turn on the connected amplifier

last to prevent spikes that can easily damage your loudspeakers.

Before turning on the amplifier, make sure that no signal is

going through the DDM4000 in order to avoid sudden and

unpleasant surprises. We recommend turning down all faders

and knobs beforehand.

(74) The MAIN OUT connector panel consists of OUT A, OUT B and TAPE outputs:

• The signal at OUT A is the same as at the XLR outputs (73).

• You can connect an additional amplier to output OUT B which can be

used for a DJ booth or a second club zone, for example. The volume of

the OUT B signal is (independent of OUT A) individually adjusted with

the OUTPUT B knob (32).

• The TAPE output allows you to connect a recording device in order to

tape-record your mix. The output level is independent of OUT A and

OUT B and can be adjusted in Output Setup (see Chapter 6.2).

(75) DIGITAL OUT is the digital output of the DDM4000. This is where you nd

the TAPE signal in CD quality (16 bit/44.1 kHz).

◊ Use Output Setup (see Chapter 6.2) to adjust further settings of the

output section.

(76) These are the MIDI IN, MIDI OUT and MIDI THRU connectors that allow you

to connect external MIDI equipment and synchronize with their MIDI Clock.

◊ Read more about the MIDI functions of the DDM4000 in Chapter 7.

2.9 Power section

(79)

(78)

(77)

Fig. 2.9: The POWER section

(77) Power is supplied via an IEC connector. The matching cable is provided

with the unit.

(78) FUSE RETAINER/VOLTAGE SELECTOR. Please make sure that the voltage

indicated by the voltage selector matches the local voltage before you

connect the unit to the main power supply. Always replace blown fuses

with fuses of the same type and rating. Some units feature a fuse retainer

in which a selection between 230 V and 120 V is possible. Please be aware:

When using your unit outside of Europe with 120 V, a fuse with a higher

rating is required.

(79) Use the POWER switch to turn on the DDM4000. Before connecting the

unit to the power mains, ensure that the POWER switch is in OFF position.

When the unit is in operation, ensure that the mains plug is accessible.

◊ Attention: The POWER switch does not fully disconnect the unit

from the mains. To disconnect the unit from the mains, pull out the

main cable plug or appliance coupler. When installing the product,

ensure the plug or appliance coupler is readily operable. Unplug the

power cord completely when the unit is not used for long periods

of time.

The serial number of the DDM4000 is found on the bottom side of the device.

10 DIGITAL PRO MIXER DDM4000 User Manual

2.10 Hookup example

CD player Turntable

Drum Machine

DJ Booth

Dance oor

Digital Recorder

Microphone

Fig. 2.10: Application example of hooking up the DDM4000

11 DIGITAL PRO MIXER DDM4000 User Manual

3. Operation

3.1 Console setup

Console Setup allows you to make all standard settings for the DDM4000.

1) Press the CONSOLE SETUP knob (51) for approximately 2 seconds.

The setup list appears in the center of the display.:

2) Turn the CONSOLE SETUP knob to select the setup you want to edit.

3) Press the CONSOLE SETUP knob to conrm the selection.

Exit Console Setup:

• Press the ESC push button (52) to exit Console Setup.

Some of the setup pages can be accessed in dierent ways. This is the case

for Mic Setup and User Settings:

Open Mic Setup:

1) Press the MIC SETUP push button (16) to access Mic Setup.

2) Press the MIC SETUP push button (16) again to exit Mic Setup.

Open User Settings:

1) Press the LOAD push button (35) to access User Settings.

2) Press the LOAD push button (35) again to exit User Settings.

3.1.1 Selection lists on screen

The individual setup pages contain further selection lists, which appear either

on the left or right side of the display, in addition to the Console Setup list.

Left:

1) Turn the left PARAMETER knob (45) (in the FX 1 section) to select the

preferred function from the list.

2) Press the left PARAMETER knob to conrm the selection.

Right:

1) Turn the right PARAMETER knob (45) (in the FX 2 section) to select the

preferred function from the list.

2) Press the right PARAMETER knob to conrm the selection.

3.2 Using stereo channels

3.2.1 EQ modes: SINGLE and MULTI

The equalizer provides Preset push buttons, labeled P1, P2 and P3, with which

preset congurations are stored. The behavior of the push buttons depend on

the selected EQ mode: Single Mode or Multi Mode. After switching on the device,

Single Mode is active.

SINGLE Mode:

In Single Mode, the push buttons P1, P2 and P3 (6) are each permanently

assigned to a frequency band (P1 = HIGH, P2 = MID, P3 = LOW). This means that

a Preset can be assigned to each EQ control. When activated, the Preset push

buttons provide a Kill function with maximum attenuation (-∞ dB).

Preset settings in SINGLE Mode

P1 HIGH Kill -∞ dB Suppresses high frequencies

P2 MID Kill -∞ dB Suppresses mid frequencies

P3 LOW Kill -∞ dB Suppresses low frequencies

Tab. 3.1: Functionality of Preset push buttons in Single Mode

The degree of cut can, however, be modied. Alternatively, a frequency boost

can also be stored. In case you want to boost instead of cutting the bass

(Punch function), proceed as follows:

1) Turn the LOW knob (4) to the right until you have reached the

boost you want.

2) Press and hold the MODE push button (5) while pressing P3 (6).

3) Press P3 to load the Preset. The bass frequencies are now boosted.

P3 ashes blue.

This way you can also program the mids and highs with P2 and P1 respectively.

Reset:

The Preset push buttons can be restored to their initial states at all times

(Reset function):

• Press MODE (5) for approximately 2 seconds. The MULTI LED briey lights up

to conrm the reset.

MULTI Mode:

In Multi Mode, the Preset push buttons are not assigned to individual EQ bands,

but are assigned to the 3-band equalizer as a whole. This way you can create

three EQ presets and assign these to the Preset push buttons. When activated,

the Preset push buttons are assigned as follows:

Preset settings in MULTI Mode

P1 High pass Suppresses MID and LOW

P2 Band pass Suppresses HIGH and LOW

P3 Low pass Suppresses HIGH and MID

Tab. 3.2: Functionality of Preset push buttons in Multi Mode

• To activate Multi Mode, press the MODE push button (5).

The MULTI LED lights up.

To create your own EQ presets, proceed as follows:

1) Adjust the equalizer as needed by turning the LOW, MID and HIGH knobs.

2) Press and hold the MODE push button (5) while pressing P1 (6).

3) Press P1 to load the EQ Preset. P1 ashes yellow.

Two more EQ Presets can be stored with P2 and P3.

Reset:

The Preset push buttons can be restored at all times:

• Press MODE for approximately 2 seconds. The SINGLE LED briey lights

up to conrm the reset.

12 DIGITAL PRO MIXER DDM4000 User Manual

3.2.2 Channel setup

In Channel Setup, you can ne-tune the characteristics of the stereo

channels’ equalizer. It is also possible to adjust a Subsonic Filter (low-cut

lter) for all four channels. For example, this lter can be used to suppress

low-frequency noise from turntables.

1) Press the CONSOLE SETUP knob (51) for approximately 2 seconds.

2) Select “Channel Setup” by turning and pressing the CONSOLE SETUP knob.

Channel Setup appears on the display.

The equalizer of the stereo channels has 3 bands with dierent characteristics.

The Mid band is a peak lter whose center fre-quency and bandwidth

(Q factor) can be modied. Both outer bands Low and High are shelving lters.

In Channel Setup, following settings are available for each of the 4 channels:

Channel Xover (Crossover):

LOW: Cuto frequency of the Low lter. All frequencies below the adjusted

value are cut or boosted.

MID: Center frequency of the Mid band. All frequencies around this value

are boosted or cut. The bandwidth is determined by the parameter Mid Q

(see below).

HIGH: Cuto frequency of the High lter. All frequencies above the adjusted

value are boosted or cut.

1) Press the left PARAMETER knob (45) to select the parameter

(LOW, MID or HIGH).

2) Turn the PARAMETER knob to change the cuto frequency and center

frequency of the selected band.

Mid Q:

The Q factor determines the behavior of the lter. The higher the value,

the narrower the bandwidth. Mid Q aects the mids band.

• Turn the CONSOLE SETUP knob (51) to change the value of the Q factor.

Subsonic frequency:

You can adjust the cuto frequency of the low-cut lter on each stereo channel.

All frequencies below the cuto frequency are attenuated.

1) Press the right PARAMETER knob (45) to select the channel.

2) Turn the PARAMETER knob to change the cuto frequency.

Exiting Channel Setup:

• Press the ESC push button (52) to exit Channel Setup.

3.3 Operating the microphone channel

3.3.1 Mic setup

You can make adjustments to the sound settings of the Microphone channel,

the Ultramic processor and the Mic eects by using Mic Setup. This is how to

access Mic Setup:

1) Press the CONSOLE SETUP knob (51) for approximately 2 seconds.

2) Select “Mic Setup” by turning and pressing the CONSOLE SETUP knob.

Alternatively, you can access Mic Setup as follows:

• Press the MIC SETUP push button (16) on the microphone channel.

The MIC SETUP push button lights up as long as you are using Mic Setup.

Mic Setup appears on the display containing several submenus. On the

left-hand side of the display you see a list from which the following submenus

can be selected:

• Turn the left PARAMETER knob (45) to select the submenu you want to edit:

EQ Freq/Pan page:

This page shows level meters for both microphone signals. In addition, you can

make sound settings for the equalizer on the Microphone channel. Here you can

adjust the stereo image of the microphone signal as well as the signal relation

of both microphones to each other. The individual parameters are as follows:

MIC 1: Level meter for Microphone 1

MIC 2: Level meter for Microphone 2

LOW: Cuto frequency of the LOW control knob

MID: Center frequency of the MID control knob

HIGH: Cuto frequency of the HIGH control knob

Q MID: Q factor of the mids band

1) Press the CONSOLE SETUP knob (51) to select the parameter

(LOW, MID, HIGH, Q MID).

2) Turn the CONSOLE SETUP knob to change the value of the selected parameter.

PAN1: Position of Microphone 1 in the stereo image

PAN 2: Position of Microphone 2 in the stereo image

OUT B: Volume of the microphone channel at Output B

1) Press the right PARAMETER knob (45) to select the parameter

(PAN 1, PAN 2, OUT B).

2) Turn the PARAMETER knob to change the value of the parameter.

13 DIGITAL PRO MIXER DDM4000 User Manual

EQ GAIN page:

This page lets you make user default sound settings, which aect the microphone

channel in relation to the equalizer. For example, storing a boost of 5 dB in these

settings aects the signal even when the HIGH rotary knob is set to 0, that is the

center position. The high frequencies can additionally be boost or cut with the

HIGH knob. This function helps to remove problematic frequencies of your voice

or to improve speech comprehensibility.

MIC 1 LOW CUT: Cuto frequency of the high-pass lter

(Microphone 1)

MIC 1 LOW, MID, HIGH: EQ default settings for Microphone 1

1) Press the CONSOLE SETUP knob (51) to select the parameter

(LOW, MID, HIGH).

2) Turn the CONSOLE SETUP knob to change the value of the selected parameter.

MIC 2 LOW CUT: Cuto frequency of the high-pass lter

(Microphone 2)

MIC 2 LOW, MID, HIGH: EQ default settings for Microphone 2

1) Press the right PARAMETER knob (45) to select the parameter

(LOW, MID, HIGH).

2) Turn the PARAMETER knob to change the value of the selected parameter.

ULTRA MIC 1 and 2:

The Ultramic processor is a 2-band compressor that reduces the dynamic range of

speech. The level of loud sounds is reduced and the level of quiet sounds is raised.

This decreases the dierence between the loudest and quietest passages.

By splitting the signal into two frequency bands, a thicker, more powerful

sound is achieved without the typical artifacts, such as pumping sound or a

loss of clarity.

The settings for both microphone signals are made separately. That’s the reason

for having two Ultramic pages. For Mic 1, select the page “Ultramic 1” and choose

“Ultramic 2” for Mic 2. The parameters on both pages are identical so that they

only have to be described once.

You can see several level meters on the display. Three parameters of the

compressor are adjustable plus you can also load presets.

The meters:

MIC I Shows the input level

MIC 0 Shows the output level

COM Shows the compression ratio for the low (L) and

high (H) frequency band

EXP Shows the attenuation of the expander for the low (L) or

high (H) frequency band

Adjustable parameters

THRSH Threshold species the cuto frequency of the Ultramic processor

FREQ Adjusts the crossover frequency between the upper

and lower frequency band

EFFIC Eciency: Adjusts the level of compression

1) Press the CONSOLE SETUP knob (51) to select the parameter

(THRSH, FREQ, EFFIC).

2) Turn the CONSOLE SETUP knob to change the value of the

selected parameter.

Ultramic presets:

The following default settings can be loaded:

1) Turn the right PARAMETER knob (45) to select the preset.

2) Press the PARAMETER knob to load the preset.

MIC FX page:

On the Mic FX page, you can select the type of eect you want to use

for the microphone signal. The following eects are available:

1) Turn the right PARAMETER knob (45) to select the preset.

2) Press the PARAMETER knob to load the preset.

Each eect can be modied in order to suit your individual taste. Two parameters

are available for this reason. The second parameter always adjusts the eect

Dry/Wet Mix—this applies to all eects.

Eect descriptions:

FLANGER: A anger eect occurs through frequency modulation. You can adjust

the speed of the LFO (Low Frequency Oscillator).

PHASER is similar to a anger. Only this time around, modulation is

achieved through phase-shifting. You can adjust the speed of the LFO.

DELAY is a signal delay. You can change the delay time (Time).

ECHO is similar to the delay eect, with the dierence that the delayed signal is

repeated several times.

PITCH changes the pitch of the signal and therefore the pitch of the vocalist’s and

speaker’s voice. Shift is used to adjust the pitch.

14 DIGITAL PRO MIXER DDM4000 User Manual

BITCRUSHER reduce the digital resolution. The bit depth is adjustable.

REVERB is a reverberation eect. Eight dierent types of reverberation

are available. These are described in detail in Chapter 4.1.4.

1) Press the CONSOLE SETUP knob (51) to select a parameter.

2) Turn the CONSOLE SETUP knob to change the value of this parameter.

You can match the time parameter of the anger, phaser, delay and echo eects

to the beat by tapping the tempo with the left TAP push button (50) as long as

Mic Setup is displayed (MIC SETUP push button (16) shines when active).

Exiting Mic Setup:

• Press the ESC push button (52) to exit Mic Setup.

3.3.2 Talk setup

The Talkover function is useful when making announcements while the music

is playing. The level of the music, is attenuated as soon as you speak into

the microphone. All necessary settings of this function are made in Talk Setup.

This is how you access Talk Setup:

1) Press the CONSOLE SETUP knob (51) for approximately 2 seconds.

2) Select “Talk Setup” by turning and pressing the CONSOLE SETUP knob.

The Talk Setup page appears on the display.

This page displays level meters for both microphones. On the left-hand side

of the screen, there is a list from which you can select a Talkover preset.

Loading presets:

1) Turn the left PARAMETER knob (45) to select the preset.

2) Press the PARAMETER knob to load the preset.

Editing talkovers:

The following parameters of the Talkover function are adjustable:

THRSH Threshold. The music signal is attenuated as soon as the

microphone signal exceeds this value.

MAX. ATT Maximum Attenuation. This lets you adjust the music’s maximum

attenuation while speaking into the microphone.

SPEED Adjusts the speed at which the signal’s volume level is reduced.

1) Press the right PARAMETER knob (45) to select the parameter

(THRSH, MAX. ATT, SPEED)

2) Turn the PARAMETER knob to change the value of the parameter.

Exiting Talk Setup:

• Press the ESC push button (52) to exit Talk Setup.

3.4 Operating the crossfader

The use of the Crossfader is easy to understand, even for a DJ novice.

But the DDM4000 wouldn’t be a digital mixer if it hadn’t a couple of special

functions to oer that cannot be easily realized with an analog DJ Mixer.

3.4.1 Crossfader modes: KILL and X-OVER

There are three push buttons labeled HIGH, MID and LOW ( (22) ) on the left-hand

side and on the right-hand side of the Crossfader. When activated, they function

as Kill switches, that is they can suppress specic frequency bands.

X-Over (Crosssover) Mode lets you realize completely new, breathtaking eects.

In this mode, it is possible to assign specic frequency bands to Side A and B

that can then be crossfaded.Here’s an example to make the functionality clear:

1) Move the crossfader (20) to the left (A).

2) Press the FULL FREQ push button (23) in Section A.

3) Press the Kill push button (22) “MID” in Section B.

In the left crossfader position, the A signal is played back in its complete

frequency range. By moving the crossfader to the right, only the mid frequencies

of the B signal are faded in while the mids of the A signal are faded out.

The low and high frequencies of the A signal remain audible. As a result,

the low and high frequencies of the A signal together with the mid frequencies

of the B signal are audible at the output of the mixer.

X-Over Mode keeps your mixing style fresh and unique. You can activate

X-Over Mode in Crossfader Setup.

3.4.2 Crossfader setup

This is how you access Crossfader Setup:

1) Press the CONSOLE SETUP knob (51) for approximately 2 seconds.

2) Select “Crossfader Setup” by turning and pressing the CONSOLE SETUP knob.

The Crossfader Setup page appears on the display:

On the display’s left side, you can adjust the frequency crossfade of the

Kill push buttons. On the right side, you can select Cross-fader Mode.

XOVER CF (Crossover Center Frequency):

LOW: Crossover frequency between LOW and MID

HIGH: Crossover frequency between MID and HIGH

1) Press the left PARAMETER knob (45) to select the parameter (LOW, HIGH).

2) Turn the PARAMETER knob to change the value fo the selected parameter.

Crossfader Mode:

1) Turn the right PARAMETER knob (45) to select the mode (KILL, X-OVER).

2) Press the PARAMETER knob to conrm.

15 DIGITAL PRO MIXER DDM4000 User Manual

Exiting Crossfader Setup:

• Press the ESC push button (52) to exit Crossfader Setup.

3.4.3 Bounce to MIDI clock

This function automates bouncing. Bouncing is hard crossfading with the

crossfader in the rhythm of the music. The internal MIDI Clock needs to be

active for this function to work. The clock is a reference for the bounce speed

that ranges between one and 16 beats.

Before pressing the BOUNCE TO MIDI CLK push button to start the bounce,

you should specify a the Bounce speed:

1) Start the MIDI Clock by pressing MIDI START-STOP push button (52).

2) Select the bounce speed by using the BEAT push buttons (28).

The LEDs (29) indicate the beats.

3) Now press the BOUNCE TO MIDI CLK push button (27) to start the bounce.

When the crossfader is on Side A, the bounce starts with the A signal,

whereas when the crossfader is on B, the bounce starts with the B signal.

3.5 Operating the main section

There are also several functions in the Main section that surpass the functional

capacity of an analog mixer. This way complete mixer settings can be stored

and loaded. And the Ultramizer makes sure that your beats sound even fatter.

3.5.1 Ultramizer

The Ultramizer is a multiband processor that compresses the audio signal in

order to achieve a better perception of volume without having to increase

the level. As a result, the performance of an amplier is optimally used and your

music feels louder than it really is. The processing takes place in two individual

frequency bands in order to achieve a more powerful sound without the

unwanted side eects, such as the pumping eect and loss of high frequencies.

1) Press the ULTRAMIZE ON/OFF push button (34) to activate the Ultramizer.

2) Press the CONSOLE SETUP knob (51) for approximately 2 seconds.

3) Select “Ultramize” by turning and pressing the CONSOLE SETUP knob.

The display switches to the Ultramizer page. Here you can change settings

plus load and edit presets:

Loading presets:

1) Turn the left PARAMETER knob (45) to select the preset.

2) Press the PARAMETER knob to load the preset.

Editing the Ultramizer:

RANGE Describes the adjustable dynamic range. A value of 10 dB results in

a maximum level boost of 10 dB.

TIME Changes the adjustable speed of the Ultramizer.

• Turn the CONSOLE SETUP knob (51) to change the TIME parameter.

• Turn the PARAMETER knob (45) to change the RANGE parameter.

Exiting the Ultramizer setup:

• Press the ESC push button (52) to exit the Ultramizer setup.

3.5.2 Loading and saving user settings

A great advantage of a digital mixer is the possibility to store entire mixer

settings in order to recall them later on at the ick of a switch. Big studio

consoles refer to this function as “Snapshot” because all settings are captured

(as with a snapshot). This lets you adjust the mixer to your way of working and

recall settings you made at any time.

Just imagine, a club has the DDM4000 which is being used by several DJs.

Each DJ has stored personal EQ settings, kill frequencies, Ultramizer and

Eect settings, so that when it is his or her turn, the preferred settings can be

recalled immediately. The other way around, a guest DJ, who is not accustomed

to the DDM4000, is able to take o without having to adjust any settings

in advance.

◊ After switching on the device, the last selected preset is loaded.

Loading user settings:

1) Press the LOAD push button (35). The LOAD push button ashes.

“User Setup” appears on the screen, displaying the preset list:

2) Turn the left PARAMETER knob (45) to select a user setting

(or the factory preset).

3) Press the PARAMETER knob again to load the user setting.

Storing user settings:

1) Press the LOAD push button (35) to access User Setup with its preset list.

2) Turn the CONSOLE SETUP knob (51) to select a memory location.

3) Press the CONSOLE SETUP knob to store the user setting.

◊ It is not possible to overwrite the factory preset.

Ultramizer presets

Gentle Boost Gentle volume boost

Boost Noticeable volume boost

Pump Strong volume boost with pumping eect

Full Maximum volume boost

Full Pump Maximum volume boost with pumping eect

16 DIGITAL PRO MIXER DDM4000 User Manual

Exiting User Setup:

• Press the LOAD push button (35) or the ESC push button (52)

to exit User Setup.

3.6 Operating the phones section

You can use the headphones to listen to two dierent signals: 1. The PGM

signal (=Program): This is the signal at the MAIN output. 2. The PFL signal

(=Pre Fader Listen): This is the signal which can be routed to the PFL bus by using

the PFL push buttons (7). The PFL signal is fader-independent, which means it

can even be heard when the faders are pulled down.

When the SPLIT push button (40) is not pressed, both the PGM and PFL signal are

played back in stereo in the headphones. The mix of both signals is adjusted with

the MIX knob (38). When the knob is turned completely to the left, the PFL signal

is heard, whereas when turned completely to the right, the PGM signal is heard in

both headphones.

Working in Split Mode:

• Press the SPLIT push button (40) to activate Split Mode.

When using Split Mode, the PFL signal is played back on the left headphone

while the PGM signal is played back on the right headphone (both mono signals).

4. BPM and Eects Section

Fig. 4.1: BPM and Eects section

The BPM and Eects section in the middle of the mixer can either be used for

the stereo channels or the master signal. Both processors can also be combined

to be used as dual eect for individual channels. What’s more, both Microphone

channel and Sampler feature their own eect processors, which are described in

individual chapters (Chapter 3.3.1 and Chapter 5.4).

Display:

The display shows the following information:

A Shows the eect type and the parameter values.

B Shows the calculated speed in BPM (Beats Per Minute). It Also gives

information on the signal assignment and the Tap function.

C This section shows the BPM-synchronized eect parameters as beats

on the right side. On the left, you see the activity of the Kill function in

the eect path.

D This information refers to the Sampler and/or the MIDI Clock

(see Chapter 5).

4.1 Eects section

(51)(48)(47)(46)(41)

(50)

(44)

(49)(43)

(45)

(42) (53) (52)

Fig. 4.2: Eects section (here FX 1)

4.1.1 Selecting the signal source

To use an eect, you rst have to assign the eect to a signal source.

This assignment also applies to the BPM Counter. Possible input sources

are as follows:

INPUT 1 – INPUT 4: Stereo channels 1 – 4.

MUSIC: Stereo sum signal (main signal).

CHAIN: CHAIN assigns the eect to the signal of the other eects section,

so that 2 eects are triggered consecutively.

Selecting a signal for FX 1:

1) Press the FX 1 ASSIGN push button (43).

2) Turn the left PARAMETER knob (45) to select a signal source from the list.

3) Press the left PARAMETER knob to conrm the selection.

17 DIGITAL PRO MIXER DDM4000 User Manual

Selecting a signal for FX 2:

1) Press the FX 2 ASSIGN push button (43).

2) Turn the right PARAMETER knob (45) to select a signal source from the list.

3) Press the right PARAMETER knob to conrm the selection.

4.1.2 Activating an eect

1) Press the FX ON push button (42) to activate the eect. Both the FX ON

push button and the EFFECT/BAND push button (46) – (48) ash.

2) Turn the DEPTH knob slowly to the right until you hear the eect

as is intended.

Kill function on the eect path:

A specially eective way of alienation is to remove individual frequency bands

from the eect processing. There are three additional Kill switches that are found

on the signal path leading to the eects unit. The EFFECT/BAND push buttons

of the activated eect ash blue corresponding to the frequency bands that are

active. By pressing the push buttons you are able to “kill” the frequency bands.

And the display shows the Kill function’s status.

• Press one of the EFFECT/BAND push buttons ( (46), (47), (48) ) while the eect

is active. The push-button LED of the deactivated band goes out.

4.1.3 Selecting an eect

Nine eect types are available. The eect table in Chapter 4.1.4 gives an

overview of the possible eects and their adjustable parameters.

1) Press the SELECT push button (46). The display shows a list of all

types of eects.

2) Turn the PARAMETER knob (45) to select the eect type.

3) Press the PARAMETER knob to load the eect type.

4.1.4 Eect descriptions

The following gives you a description of the available eects and

adjustable parameters. (BPM-synchronized parameters are printed in italic.) The

tables show you which controls are used to adjust the parameters. Chapter 4.1.5

describes eect processing. Chapter 4.1.6 gives you the information you need

to know about BPM-synchronized parameters.

FLANGER, PHASER, PAN:

FLANGER: The anger eect is achieved by frequency modula-tion. You are able

to adjust the speed of the LFO (Low Frequency Oscillator), the amount of the

eect signal that is fed back to the input (Feedback), the eect depth (Depth)

and the degree of phase shifting represented in rhythmical units (Phase).

Use Fade in case you want the anger to complete its period of oscillation

after the eect has been turned o, to avoid an abrupt truncation of the eect.

PHASER is similar to the anger. In this case the modulation is achieved through

phase shifting. You can adjust the speed of the LFO and the eect depth (Depth).

Use Fade to determine if the eect is to end abruptly or softly fade out.

PAN specied an eect which lets the signal move from the right to the left side

of the stereo image. This eect sounds the most intensive when the DEPTH knob

is turned right up. LFO adjusts the speed of the panning and Depth adjusts the

eect depth.

1/5 2/5 3/5 4/5 5/5

LFO Speed Feedback Depth Phase Fade Dry/Wet Mix

PHASER

LFO Speed Depth Fade — — Dry/Wet Mix

LFO Speed Depth — — — Dry/Wet Mix

PAN

FLANGER

Tab. 4.1: Eect parameters for Flanger, Phaser and Panning

DELAY, ECHO:

DELAY is a signal delay. The delay time (Time) can by synchronized with

the BPM Counter. A simple delay (Simple) and the 3-Pong Delay, which spreads

the delays across the whole stereo image, are available.

ECHO is similar to the delay. The only dierence is that the delayed signal is

repeated several times. Use Feedback to specify the number of times that the

delay is to be repeated. Fade determines if the echo is to fade out (On) or not

(O) when the eect is turned o.

1/5

TIME

2/5

MODE

3/5

FDBK

4/5

FADE

DELAY

10...

5930 ms

Simple

3Pong— — Dry/Wet Mix

ECHO

10...

5930 ms

Simple

3Pong0 - 100% Dry/Wet Mix

Tab. 4.2: Eect parameters for Delay and Echo

18 DIGITAL PRO MIXER DDM4000 User Manual

PITCHER, BITCRUSHER:

PITCHER changes the pitch of the music without changing the tempo.

Shift adjusts the pitch.

BITCRUSHER simulates a decrease in the digital resolution.

From soft lo- settings to toy sounds, everything is possible.

1/1

PITCH

Shift: -100 ... +100% —

BITCRUSHER

Depth: 0 ... +100% Dry/Wet Mix

Tab. 4.3: Eect parameters for Pitch and Bitcrusher

REVERB:

REVERB is a reverberation eect. Eight dierent reverb room simulations

are available. When Fade is activated, the reverberation decays and is not

truncated in case the eect is turned o.

Ambient is a very short reverb which lets you virtually hear the walls of the room.

Box delivers a spatial impression without long reections.

Cathedral: The long and dense reverb of a big cathedral, ideal for slow tracks.

Cavern: An intensive, high-frequency-dominant reverb based on a cave

with rocky walls.

Chamber produces the short reverb of a small room.

Chorus: A thick, warm reverberation which is shorter than that of Cathedral.

Concert simulates the well-dened reverb of a big concert hall.

Echo: A thick, short reverb with a longer pre-delay.

2/4

FADE

Ambient, Box, Cathedral,

Cavern, Chamber, Chorus,

Concert, Echo

Dry/Wet MixOn/O

1/4

MODE

Tab. 4.4: Eect parameters for Reverb

FILTER:

FILTER is an eect which is typically associated with synthesizer music.

Three types of lters are available: Band Pass, Low Pass and High Pass.

Resonance is used to increase the level of the lter frequency which makes

the eect sound more intensive. In LFO Mode, the lter frequency is controlled

by an LFO. Manual Mode lets you control the lter frequency with the

DEPTH knob (44).

1/1

FILTER

2/4

RESO

3/4

MODE

4/4

LFO

FILTER

Lowpass

Bandpass

Highpass

0 ... 100%

LFO

Manual

Frequency

LFO Speed

Tab. 4.5: Eect parameters for Filter

4.1.5 Editing eects

As already mentioned in the previous chapter, each eect has up to ve

parameters (depending on the eect type) with which you can adjust

the eect. In each case it is possible to adjust one parameter by using the

BEAT push buttons. In most cases, this is the BPM-synchronized parameter.

Eect parameters:

1) Press the PARAMETER push button (47) to select a parameter. This only

works when the eect is deactivated (the FX ON push button does not ash).

2) Alternatively, press the PARAMETER knob (45) to select a parameter.

3) Change the parameter value by turning the PARAMETER knob (45).

4) To switch to the next parameter, press PARAMETER (45) or (47) again.

Dry/Wet mix:

• Turn the MIX knob (44) slowly to the right to mix the eect (Wet) to the

original signal (Dry).

19 DIGITAL PRO MIXER DDM4000 User Manual

4.1.6 BPM-synchronized eect parameters

Some of the eect sound especially interesting when time-related parameters

respond to the rhythm of the music. The DDM4000 supports editable,

BPM-synchronized parameters.

Editing BPM-synchronized parameters:

1) Make sure that the BPM Counter calculates the correct value

(if applicable, enter manually with TAP, see Chapter 4.2).

2) Change the parameter step-by-step with the BEAT push buttons (49).

The selected value appears on the display.

DELAY, ECHO:

For the delay and echo eect, you can edit the delay time in musical units.

The number of beats is displayed:

Fig. 4.3: Beats and note values for delay and echo

A rhythmical representation of the whole looks like this

(showing a selection of several beats):

Fig. 4.4: Rhythmically represented delay parameter

FLANGER, PHASER, PAN, FILTER:

For the lter eect, the BPM synchronization is only possible in LFO Mode.

You can adjust the speed of the modulation (LFO speed). The values 1–32

correspond to the number of beats that are needed for one oscillation period:

Fig. 4.5: Beats and note values for modulation eects

The following picture results from the musical context:

Fig. 4.6: LFO parameter, represented in beats and bars

4.1.7 FX setup

FX Setup lets you specify the crossover frequencies between the individual bands

of the EFFECT/BAND push buttons (46) – (48) (Kill function on the eect path,

see Chapter 4.1.2). This is individually done for both eect devices.

Adjustable parameters:

FX 1 LOW / FX 2 LOW: Crossover frequency between LOW and MID.

FX 1 HIGH / FX 2 HIGH: Crossover frequency between MID and HIGH.

1) Press the left or right PARAMETER knob (45) to select the parameter for

FX 1 and FX 2.

2) Turn the left or right PARAMETER knob to change the value of

the selected value.

4.2 BPM counter

The Auto BPM Counter is automatically able to convert the tempo of the track

being played into BPM (Beats Per Minute). The detected BPM values are the

basis for all time-related eect parameters and for the recording duration

of the sampler. The BPM can be detected in two dierent ways: manually

and automatically. In both cases, the current BPM is shown in Section B of

the display.

20 DIGITAL PRO MIXER DDM4000 User Manual

Automatically detecting beats with AUTO BPM:

The BPM Counter detects the tempo of the signal source assigned to

the Eect section. The signal source is shown in the BPM section of the

display. (Assigning the signal source to the BPM/Eect section is described

in Chapter 4.1.1.)

1) Make sure that “Auto BPM” is activated. When active, the AUTO BPM

push button (50) shines yellow and the BPM indicator ashes on the display.

◊ Should Tap Mode be active (AUTO BPM push button shines blue),

press the AUTO BPM push button longer than one second to

activate Auto BPM.

2) Now the BPM Counter determines the BPM value of the played signal.

It is constantly brought up to date to be able to respond immediately to

any tempo changes.

Manually detecting beats with TAP:

1) Make sure that Tap Mode is activated. When active, the AUTO BPM/TAP

push button (50) shines blue and the BPM indicator shows “Manual.”

2) Tap the TAP push button (50) (at least 2x) in the rhythm of the music,

which results in a constant BPM value. Here’s a tip: while tapping,

listen in on the signal using the headphones.

◊ Should Auto BPM be active (AUTO BPM push button

shines yellow), go to Step 2. When tapping the tempo, Manual Mode

is automatically activated.

3) The BPM value can always be readjusted by tapping over and over again.

◊ The Auto BPM is always active when the device is turned on.

◊ Without a music signal (or one which is too quiet), the BPM value

flashes on the display. In addition, the message “Low Level” appears on

the display. The BPM value also flashes when the beat cannot be clearly

identified (message “Uncertain”).

4.3 MIDI clock

The MIDI Clock is used as a time reference for the Bounce function. In addition,

the MIDI Clock is given out at the MIDI output. This allows you to synchronize

external devices, which are able to receive MIDI Clock (such as drum machines

and grooveboxes) with the DDM4000.

(53)

(52)

(51)

Fig. 4.7: BPM section

• Press the push button (52) to start and stop the MIDI Clock.

You can adjust the tempo of the MIDI Clock. Alternatively, the MIDI Clock can also

be synchronized with one of the two BPM Counters:

MIDI BPM:

When in MIDI BPM Mode, “MIDI BPM” appears in the middle of the display

below the BPM indicator of the MIDI Clock. Adjust the tempo by turning the

CONSOLE SETUP knob (51). It is possible to make bigger value jumps by pressing

and simultaneously turning the knob.

FX 1/FX 2 BPM:

To transmit the detected tempo of the BPM Counter to the MIDI Clock,

press one of the ADJUST push buttons (53). By pressing the left BEAT push button,

the MIDI Clock adopts the tempo of the left BPM Counter. By pressing the right

BEAT push button, the MIDI Clock adopts the tempo of the right BPM Counter.

The assignment is indicated by displaying “FX 1 BPM” or “FX 2 BPM.”

Cancel the assignment by turning the CONSOLE SETUP knob to specify

your own tempo.

The tempo of the MIDI BPM can also be transmitted to the BPM Counter. Hold the

left or right ADJUST push button (53) (or both at the same time) while selecting

the tempo with the CONSOLE SETUP knob (51). This function is useful when

assigning eects to a channel which is congured as MIDI controller so that the

Auto BPM function does not work.

5. Sampler

(54)

(60)

(61)

(64)

(66)

(65)

(63)

(62)

(59)

(58)

(57)

(56)

(55)

Fig. 5.1: Sampler section

A sampler is a device used to record and play back audio signals.

The DDM4000’s sampler lets you record two tracks which then can be

played back. These tracks are single short sequences, vocal phrases, rhythmic

loops or even longer song passages. Any audio signal fed to the mixer can be

used as signal source, usually found on the stereo channels, the Microphone

channel and the stereo sum. The maximum recording duration is 32 seconds.

The samples can be played back in various ways (as innite loop/loop, one time,

forward, reverse).

21 DIGITAL PRO MIXER DDM4000 User Manual

5.1 Recording samples

1) Select a signal source with the REC SOURCE push buttons (56).

The signal source is indicated above the REC SOURCE LEDs:

Signal sources:

1, 2, 3, 4: Stereo channel 1, 2, 3 or 4

MIC: Microphone channel

MST: Master (stereo sum)

2) Use the SAMPLE LENGTH push buttons (58) to specify the recording

duration you want. The length ranges between 1 and 16 beats or “∞”

(innite recording).

◊ The actual recording time depends either on the detected BPM tempo

or the MIDI Clock. The Sampler synchronizes with the BPM Counter

provided that the BPM Counter is assigned to Channel 1, Channel 2 or

Master. When this is not the case, the Sampler is synchronized with

the MIDI Clock.

3) Use BANK ASSIGN (60) to select the memory bank. The MODE push button

(61) of the selected bank lights up yellow to indicate its readiness to record.

4) Start the recording by using the RECORD/IN push button (59).

5) The recording stops after the number of beats specied beforehand.

6) Alternatively, stop the innite recording (∞) by pressing the PLAY/OUT

push button (45) or by pressing the REC push button again.

◊ The recoding duration of infinite recording (∞) is specified by pressing

the RECORD/IN push button (59) and the PLAY/OUT push button (62).

In case Loop Mode is activated at the same time, the sampler

immediately switches to playback by pressing the PLAY/OUT

push button.

Memory:

The maximum recording time is 32 seconds for both banks. The recording stops

when the memory is full.

The length of a sample and the time left are shown on the Sampler Mix display.

5.2 Playing back samples

1) Turn the VOLUME/MIX knob (55) to the center position.

2) Press the PLAY push button to start playback.

3) Press PLAY a second time to stop playback.

5.2.1 Insert function

The sample playback is carried out in Mix Mode or Insert Mode. In both cases

the sample is played back on the channel selected with REC SOURCE push

buttons (56). This can also be the stereo sum. When playing back in Mix Mode,

the sample is mixed to the specic channel or is routed to the crossfader.

When playing back the sample in Insert Mode, the sample is crossfaded to the

assigned channel.

• When playing back in Mix Mode, the INSERT push button (54) is not allowed

to be pressed (push-button LED is o). The VOLUME/MIX knob (55) is used

as a channel fader (volume) with which the sampler signal is mixed to the

signal source. The sampler signal is assigned to the crossfader by pressing

the CF ASSIGN push button (65)

• Press the INSERT push button (54) to play back the sample in

Insert Mode. The VOLUME/MIX knob (55) can now be used as crossfading

control (Mix). Turn the knob completely to the right to hear only the sample

during playback. When turning the knob to the left, the sample fades into

the signal source of the selected channel.

◊ Assigning the crossfader to the Sampler is only possible in Mix Mode.

As soon as the CF ASSIGN push button (65) is pressed, the Insert function

is automatically deactivated.

5.2.2 Reverse and loop playback

Use the MODE push buttons (61) for Bank 1/2 to determine the type of playback.

Select the playback mode for each bank:

REVERSE:

1) Tap the MODE push button to switch to Reverse Mode. The REVERSE LED

lights up. By pressing PLAY, the sample is played back in the reverse direction.

2) Tap the MODE push button again. The REVERSE LED goes out. The sample is

played back in the forward direction.

LOOP (innite loop):

1) Press the MODE push button for approximately 1 second to deactivate

Loop Mode. The LOOP LED goes out. The sample is played back as long

the PLAY push button is pressed. This type of playback is ideal for short

inserts/samples.

2) Press the MODE push button again for approximately 1 second to

activate Loop Mode. The LOOP LED lights up. The sample is played back

as innite loop by pressing PLAY.

5.2.3 Crossfader start

The Crossfader Start function lets you start the Sampler playback with

the crossfader. To be able to use this function, the Sampler needs to be

assigned to the crossfader.

1) Press the CF ASSIGN push button to route the Sampler to one side of the

crossfader (A or B).

2) Press CF START to activate Crossfader Start.

3) Press the BANK ASSIGN push button to select the bank that is to be

triggered by the crossfader.

Playback starts as soon as you move the crossfader to the side assigned

to the Sampler.

22 DIGITAL PRO MIXER DDM4000 User Manual

5.2.4 Pitch bend

The Pitch Bend function lets you change the speed of the sampler playback so

that it can be aligned to the tracks being played. There are two options:

1) Turn the BPM Adjust knob to permanently change the playback speed of the

sampler. Turn the knob to the right to speed up the tempo and turn the knob

to the left to slow down the tempo.

2) The ADJUST push buttons correspond to “Bend +” and “Bend –.”

Pressing one of these push buttons changes the speed for a short while,

in order for you to easily match the beat of the playing track.

5.3 Sampler eect

The sampler features a brake eect which simulates the braking of the rotating

platter until it comes to a halt. The length of the brakes are available as 1-beat-,

4-beat- und 8-beat brakes.

1) Press the BANK ASSIGN push button to select the memory bank that is

to be processed with the eect.

2) Select the length of the brake by continuously pressing the SELECT

push button (64). This is shown on the display.

3) Press the SMP FX ON push button (63) to activate the eect.

The push button ashes.

When the sampler comes to an end (SMP FX ON push button and PLAY/OUT push

button of the selected bank ash), the sampler-eect needs to be deactivated

by pressing SMP FX ON again in order to restart playback.

4) Press the SMP FX ON push button to restart playback.

6. Further Settings

6.1 Loading factory settings

1) Press the LOAD push button (35). The display switches to “User Setup”.

The LOAD push button lights up.

2) Select the factory preset by turning and pressing the left

PARAMETER knob (45).

3) Press the left PARAMETER knob to conrm the selection.

4) Press the LOAD push button (35) or the ESC push button (52)

to exit User Setup.

6.2 Output setup

1) Press the CONSOLE SETUP knob (51) for approximately 2 seconds.

2) Select “Output Setup” by turning and pressing the CONSOLE SETUP knob.

Output Setup appears on the display:

In Output Setup, you make the following settings:

Mono:

Use this function to switch the OUT B outputs (74) to mono.

1) Turn the left PARAMETER knob (45) to select OFF or ON.

2) Press the left PARAMETER knob to conrm.

MODE:

You can use Output A (73) together with the Subwoofer output, in which case

the bass frequencies are separated from the Main output (crossover function).

FULL-FREQ: MAIN OUT A (73) emits the entire frequency spectrum

(including the bass signal). The Subwoofer output gives

out the subwoofer signal.

CROSSOVER: The Subwoofer output gives out the subwoofer signal.

MAIN OUT A emits frequencies that are above the

crossover frequency.

1) Turn the CONSOLE SETUP knob (51) to select the mode

(FULL-FREQ, CROSSOVER).

2) Press the CONSOLE SETUP knob to conrm.

SUB OUT:

The following are used to adjust the crossover frequency and output level

of the subwoofer output.

FREQ: Crossover frequency between SUB OUT and MAIN OUT

GAIN: Output level of SUB OUT

TAPE / S/PDIF:

The levels of both Tape and S/PDIF outputs can be adjusted individually.

1) Press the right PARAMETER knob to select the parameter

(FREQ, GAIN or TAPE/ S/PDIF GAIN).

2) Turn the PARAMETER knob to change the value.

3) Press the ESC push button to exit Output Setup.

6.3 Adjusting display contrast

1) Press the LOAD push button (35). User Setup appears on the display.

2) Turn the right PARAMETER knob (45) to change the con-trast.

3) Press the LOAD push button to exit User Setup.

OUTPUT

SETUP

SUB-OUTS/PDIF

TAPE/

MONO

OFF

ON

MODE

FREQ GAIN GAIN

FULL-FREQ

CROSSOVER -6.0dB-3.0dB55Hz

OUT B

23 DIGITAL PRO MIXER DDM4000 User Manual

7. The DDM4000 as MIDI Controller

The DDM4000 can be used to control DJ or sequencer software

applications by converting individual mixer sections on the mixer to MIDI

controllers and assigning these to dened software functions. The MIDI

interface (76) is used to transmit the data. To connect to the mixer, the computer

requires a MIDI interface, which can be purchased as USB alternative for a

very reasonable price.

USB-MIDI Interface*

MIDI IN/OUT/THRU

Laptop

* not included

Fig. 7.1: Connecting the DDM4000 to a computer

7.1 MIDI protocol

The MIDI format is used for the data transmission. Knobs and faders send

Control Change messages (CC), and push buttons send Note messages

(see Table 10.2). Access the software settings to assign mixer controls to

software functions. Most software applications oer a learn function to

make the assigning even easier.

The MIDI transmission also works in the opposite direction. Basically, it is

conned to controlling the LEDs, so that a switching status in the software

application can also be shown on the DDM4000. In this case the DDM4000

receives CC messages from the computer. Each LED of the DDM4000 is assigned

to a CC number (see Table 10.3). Sending the value 0 makes the LED go out,

but sending the value 1 (or any higher value) turns on the LED.

7. 2 Common MIDI settings

The MIDI settings are made on the MIDI Setup page.

1) Press the CONSOLE SETUP knob (51) for approximately 2 seconds.

2) Select “MIDI Settings” by turning and pressing the CONSOLE SETUP knob.

The MIDI Setup page appears on the display:

This page allows you to make the following settings:

• Adjusting the MIDI channel (7.2.1)

• Sending a MIDI dump (7.2.2)

• Conguring the Microphone channel, Sampler and crossfader as

MIDI controller (7.3)

• Conguring stereo channels as MIDI controllers (7.4)

3) Press the ESC push button (52) to exit MIDI Setup.

◊ Save the settings you made in a user preset (see Chapter 3.5.2

“Storing user settings”) in case you want the settings to be active

the next time you switch on the device.

7.2.1 Setting the MIDI channel

The following describe how to specify the MIDI channel on which the DDM4000 is

to send controller data. The receiving device needs to be set to the same channel.

1) Open MIDI Setup (see Chapter 7.2).

2) Turn the left PARAMETER knob (45) to select the MIDI channel.

3) Press the ESC push button (52) to exit MIDI Setup.

7.2.2 Sending a MIDI dump

A MIDI dump sends the values of current controller positions. As a result,

the DDM4000’s settings are aligned with the connected computer.

1) Open MIDI Setup (see Chapter 7.2).

2) Press the left PARAMETER knob (45) to start the MIDI dump.

After sending the dump, the DDM4000 returns to MIDI Setup.

3) Press the ESC push button (52) to exit MIDI Setup.

24 DIGITAL PRO MIXER DDM4000 User Manual

7. 3 Conguring microphone channel,

sampler and crossfader as MIDI controller

The Microphone channel, the Sampler and the crossfader section can individually

be converted to MIDI controllers.

1) Open MIDI Setup (see Chapter 7.2).

2) Turn the CONSOLE SETUP knob (51) to select the mixer section

(MIC, SAMPLER, CROSSFADER) you want to use.

3) Press the CONSOLE SETUP knob to conrm the selection.

The LEDs of the selected section go out.

4) Press the ESC push button (52) to exit MIDI Setup.

Particularities of the crossfader:

It is not possible to assign the stereo channels to the crossfader when the

crossfader section is dened as controller. The Assign push buttons are

inoperative. The routing behaves as if the crossfader is deactivated: the signals

are directly fed to the mixer’s sum. As for the Sampler, the CF Assign function and

CF Start function are also inoperative. As usual, the routing of the Sampler signal

is realized with the REC SOURCE push button.

7.4 Conguring stereo channels as

MIDI controller

Using the channel fader (8), the EQ knobs (4) and the kill push buttons (5)

and (6) generates MIDI data when one of the 4 stereo channels is congured

as MIDI controller. The congured channel is still able to play back music,

however, the equalizer, the channel fader and the CF Assign function are

not active. In case an audio signal is being fed to the selected channel, it is routed

to the mixer’s sum without being processed and at full volume level. Simply mute

the signal in case the audio function is not required.

1) Open MIDI Setup (see Chapter 7.2).

2) Turn the right PARAMETER knob (45) to select the stereo channel you want

(and, if required, the Mute function).

3) Press the PARAMETER knob to conrm the selection. The push-button LEDs

of the selected channel go out.

4) Press the ESC push button (52) to exit MIDI Setup.

◊ Level jumps can occur when activating or deactivating the MIDI

controller function in a stereo channel depending on the position of

the equalizer and fader! Turn the OUTPUT knob in the Main and Phones

section completely to the left before activating this function.

8. Installation

The inputs and outputs of the BEHRINGER DDM4000 are RCA connectors.

The Headphone output is a stereo jack. The Microphone inputs are

XLR connectors.

◊ Make sure that only competent people install your DDM4000.

They must be sufficiently earthed during and after the

installation process. Otherwise, electrostatic discharges may

negatively affect the operating characteristics of your equipment.

output

For unbalanced use, pin 1 and pin 3

have to be bridged

1 = ground/shield

2 = hot (+ve)

3 = cold (-ve)

input

12

3

12

3

Balanced use with XLR connectors

Fig. 8.1: XLR connector

strain relief clamp

sleeve

ring

tip

sleeve

ground/shield

¼" TRS headphones connector

ring

right signal

tip

left signal

Fig. 8.2: ¼" headphones connector

shield sleevesleeve

tip tip

Fig. 8.3: RCA cable

25 DIGITAL PRO MIXER DDM4000 User Manual

9. Specications

Audio Inputs

Mic 1/2 (XLR, electronically balanced)

Max. input level -14 dBu

Input impedance 2 k

Phono (RCA)

Max. input level -18 dBu

Input impedance 47 k

Line (RCA)

Max. input level +30 dBu

Input impedance 15 k

Audio Outputs

OUT A (XLR, balanced)

Max. output level +21 dBu

Output impedance 200 

OUT A/OUT B/TAPE (RCA)

Max. output level +21 dBu

Output impedance 100 

Phones Out max. 260 mW @ 100  / 1% THD

S/PDIF (coaxial, 16 bit, 44.1 kHz)

Equalizer

Stereo Low -∞ dB/+12 dB

Stereo Mid -∞ dB/+12 dB

Stereo High -∞ dB/+12 dB

Mic Low -12 dB/+12 dB, Shelving

Mic Mid -12 dB/+12 dB, Peak

Mic High -12 dB/+12 dB, Shelving

Digital Eects Processor

DSP 2x Analog Devices Black Fin

AD/DA converter 24-bit Sigma-Delta

128-times oversampling/Cirrus

Sampling rate 44.1 kHz

LCD display 320 x 40 pixel

MIDI interface 5-pin DIN jacks In/Out/Thru

System Specications

Frequency response

Mic 25 Hz – 20 kHz, +0/-3 dB

Phono 20 Hz – 20 kHz, +0/-3 dB

Line 20 Hz – 20 kHz, +0/-3 dB

Signal-to-noise ratio

Mic > 87 dB

Phono > 83 dB

Line > 102 dB

Distortion (THD) < 0,009% (Line – OUT A)

Crosstalk < -80 dB / 1 kHz (Line)

Power Supply

Mains voltage/fuse

100 – 240 V~, 50/60 Hz T 1 A H 250 V

Power consumption max. 20 W

Mains connector standard IEC receptacle

Dimensions/Weight

Dimensions (H x W x D) approx. 4 ⁄ x 12 ⁄ x 15 ½"

approx. 110 x 320 x 392 mm

Weight approx. 12.2 lbs / 5.6 kg

BEHRINGER is constantly striving to maintain the highest professional standards. As a result of these efforts,

modifications may be made from time to time to existing products without prior notice. Specifications and

appearance may differ from those listed or illustrated.

26 DIGITAL PRO MIXER DDM4000 User Manual

10. Appendix

Parameter 1 Parameter 2 Parameter 3 Parameter 3 Parameter 4 Mix

FLANGER LFO Speed* Feedback Depth Phase Fade Dry/Wet Mix

PHASER LFO Speed* Depth Fade — — Dry/Wet Mix

DELAY Time* Mode:

Simple 3Pong — — — Dry/Wet Mix

ECHO Time* Mode:

Simple 3Pong Feedback Fade — Dry/Wet Mix

PITCH Shift — — — — Dry/Wet Mix

BITCRUSHER Depth — — — — Dry/Wet Mix

REVERB

Mode:

Ambient, Box, Cathedral, Cavern,

Chamber, Chorus, Concert, Echo

Fade — — — Dry/Wet Mix

PAN LFO Speed* Depth — — — Dry/Wet Mix

FILTER

Filter:

Lowpass

Bandpass

Highpass

Resonance

LFO:

LFO Speed*

—

—

Manual:

Depth

—

/

*These parameters can be synchronized with BPM

Fig. 10.1: Overview of eect parameters

27 DIGITAL PRO MIXER DDM4000 User Manual

Fig. 10.2: Mixer routings

MIC

L R

CH-1

L R

CH-2

L R

CH-3

L R

CH-4

L R

Sampler

L R

MASTER

MIC

L R

CH-1

L R

CH-2

L R

CH-3

L R

CH-4

L R

Sampler

L R

MASTER

L R

28 DIGITAL PRO MIXER DDM4000 User Manual

FEDERAL COMMUNICATIONS

COMMISSION COMPLIANCE

INFORMATION

Responsible Party Name: MUSIC Group Services US Inc.

Address: 18912 North Creek Parkway,

Suite 200 Bothell, WA 98011,

USA

Phone/Fax No.: Phone: +1 425 672 0816

Fax: +1 425 673 7647

DIGITAL PRO MIXER DDM4000

complies with the FCC rules as mentioned in the followingparagraph:

This equipment has been tested and found to comply with the limits for a ClassB

digital device, pursuant to part 15 of the FCC Rules. These limits are designed

to provide reasonable protection against harmful interference in a residential

installation. This equipment generates, uses and can radiate radio frequency

energy and, if not installed and used in accordance with the instructions, may cause

harmful interference to radio communications. However, there is no guarantee that

interference will not occur in a particular installation. If this equipment does cause

harmful interference to radio or television reception, which can be determined

by turning the equipment o and on, the user is encouraged to try to correct the

interference by one or more of the followingmeasures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit dierent from that to which the

receiver is connected.

• Consult the dealer or an experienced radio/TV technician forhelp.

This device complies with Part 15 of the FCC rules. Operation is subject to the

following two conditions:

(1) this device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that may

cause undesired operation.

Important information:

Changes or modications to the equipment not expressly approved by MUSIC Group

can void the user’s authority to use the equipment.

DIGITAL PRO MIXER DDM4000

29 DIGITAL PRO MIXER DDM4000 User Manual

30 DIGITAL PRO MIXER DDM4000 User Manual

31 DIGITAL PRO MIXER DDM4000 User Manual

We Hear You