Beijing Kingsmith Technology WPA1F WalkingPad Walking Device User Manual

Beijing Kingsmith Technology Co.,Ltd WalkingPad Walking Device

User Manual

Model No.: WPA1FUser ManualWalkingPad Walking DevicePlease read this manual carefully before operating the product and keep it properly.
Content1. Product and Accessories2. Function schematic diagram3. Guide for initial operation4. Learn to use WalkingPad5. Safety Notice6. Maintenance and servicing7. Hazardous substances declaration8. Trademark and legal declaration 1817161309070302Caution: The user is cautioned that changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the eq-uipment.This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause un-desired operation.NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits aredesigned to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interfer-ence to radio communications. However, there is no guarantee that interference will not occur in a particular installation.If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following mea-sures:-- Reorient or relocate the receiving antenna.-- Increase the separation between the equipment and receiver.-- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.-- Consult the dealer or an experienced radio/TV technician for help.FCC Radiation Exposure Statement:This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.This transmitter must not be co-located or operating in conjunction with anyother antenna or transmitter.User Manual
01Welcome to useMain Product01 Product and AccessoriesThank you for choosing WalkingPad Walking Device , hereinafter referred to as a WalkingPad, which posess various advantages including exquisite, simple, innovative integral design. From now on, enjoy the quality life of walking at home.Please carefully check whether the contents of the package are complete and intact. If there is any missing or damaged, please contact the seller.Power Cable Wrench Remote Controller Lanyard Silicone OilOther accessoriesParts02Expansion dimensionsFolding dimensionsThe area of Walking belt Gross weight Net weight Maximum loadApplicable age Applicable heightPerformance &indicatorsMinimum speedMaximum speedPower InputRated voltageDetailed parametersSport mode822×547×129mm/32.5"ｘ21.5"ｘ5"1200×415mm/47"ｘ16.5"1432×547×129mm/56.5"ｘ21.5"ｘ5"68 Ibs / 31kg 62 lbs / 28kg 220 lbs / 100kg 12-60 years oldUnlimited0.5 mi/hr 0.5 km/hr3.75 mi/hr 6 km/hr 746W110-120V~Standby mode /Fixed mode /Automatic modeUser Manual
03 04Walking BeltFold HingeRoller Power switch Power plugRoller Mode ButtonDisplay PanelMode Indicator Light02 Function schematic diagram1.Product main body
05 06Fault Warning LightAutomatic Mode Manual ModeStandby ModeDisplay Time Display Speed Show Distance Show Steps2.Introduction of the function of the indicator panel 3.Walkingpad remote controlACCELERATIONDECELERATION MODESTART/STOP LANYARDBATTERY COVER 02 Function schematic diagram
07 089. Start to use the walker.7. Enter novice guide. 8.Complete learning to get all functions, Otherwise, the Speed Limit is 1.75mi/hr,3.75mi/hr can be unlocked after novice guide.03 Guide for initial operation4. Connect the power line and turn on the switch.6. Open the App,follow the promptsto set up the device.1.Choose flat ground to place the walkingpad. It is forbidden to placeit on a thick and soft cushion.2. Unfold the walkingpad slowly and press it down to completely flat.3.Check and adiust the walking belt in the middle position .10. If the belt deviates from the orbit in use,please adjust properly. SEE: 06 Mainten-ance and servicing.5.Search "Walkingpad" App from Apple Store or Android Google Play and complete installation.
093. Instructions of fixed speed modecontrol (primary mode)04 Learn to use WalkingPad1. Mode instructionStandby ModeLight of the Standby mode is on;Motor and sensor stop response.Fixed speed modeLight of the fixed speed mode is on; Control the speed throughthe remote control or APP. Automatic ModeLight of the automatic mode is on; Speed is automatically controlled by intelligent algorithm.2. Instructions of the standby mode control. The motor and sensor stop respo-nding in this mode to prevent non-users from accidentally triggeringthe WalkingPad.Mode SwitchShort press: return the previous mode.Standby Mode Fixed speed modeACCELERATIONShort press: increase speed by 0.25mi.START/STOPShort press: start or stop the WalkingPad.DECELERATIONShort press: reduce speed by 0.25mi.MODE SWITCH Short press: switch to automatic mode. Long press: switch to standby mode.10In this mode, the speed of the WalkingPad canbe controlled by the remote control. It is re-commended that beginners use the fixed speedmode first and then use the automatic mode after being skilled in using the WalkingPad.Thefixed speed mode is controlled by remote co-ntrol by default, that is, the START/STOP buttonof the remote control is used to start or stop the WalkingPad, which can be modified in the client “Personalized”.
4. Description of automatic mode control (advanced mode)This mode is advanced mode, which is moredifficult and can be used completely without the remote control. It is recommended for users who have good sports coordination or have walking machine experience.Mode switch:Short press: switch to the fixed speed modeLong press: switch to the standby modeAutomatic Mode04 Learn to use WalkingPad5. Remote Controller Notice If the remote controller has no response or you change a new one, The remote controller andwalking device need to re-establishing communication.Pairing method: Restart walking device and short press the MODE Button of Controller many times during display "WAIT". 6. Fault Waming LinghtThe Fault Warning Light is off when the walking machine is working well. Whileerror occurs, the fault warning light is onand the display panel shows the error codeE01：Drive communication faultE02：Motor abnormalitiesE05：Overcurrent protectionE06：Motor ProtectionE08：Sensor FaultE10: High temperature protection, automaticrecovery after the end of countdown.E11: Overload protection, please add lubricatingoil, and resume automatically after countdown.Entering this area, theWalkingPad will slow down automatically under the automatic mode.Entering this area, the WalkingPad will start or accelerate under the automatic mode.11 12Short press: stop the WalkingPad. Under this automatic mode,set as the intelligent start and stop, the WalkingPad will start automatically to the target speed(default is 1.75 mi/hr) while entering this area.
13 1405 Safety NoticePlease keep a rear distance of 50cm or more.Please do not stand up on the walking machine when it is un-der power on and auto-calibrat-ion situation. Please choose sport shoes.Using on uneven ground is prohibited.Anti-pinch Prohibition of vertical placement Please keep a distance of 50cm or more for both sides.Prohibition of lateral placement Please pull out the plug when you’re not using it.Anti-involved, please do not trample.Folding the machine if not power off is prohibited.It is strictly prohibited to walk upand down the walking device when running.
15 1606 Maintenance and servicing1. Clean the walking machine2. Adjust the belt3. Lubricate the BeltUnplug the unit from the electrical source before you begin.Pour a little gentle detergent in the cotton rag or towel. Don’t pour the detergent on the belt directly, and don’t use acid or corrosive cleaners.Wipe down the frame, motor encasement and belt. Don’t wipe backside of the belt.After a period of using, the end part may appear dust and stains, that’s normal situation, and just clean up.Pressing both Mode Button and Acceleration Button on the remote controller over 3 seconds.The display panel shows “CALI” and the speed is 2.5mi/hr(4km/h).If belt moves left: Turn the left adjusting screw a half-circle clockwise.If belt moves right: Turn the right adjusting screw a half-circle clockwise.If belt is slipping: Turn both left and right adjusting screw a half-circle clockwise at same time.Unplug the unit from the electrical source before you begin.Lift up the belt and apply the silicone to the underside surface of the belt.Power on the walking machine.Make the machine running with 2.5mi/hr(4km/h) 10 to 20 seconds.No more 5 to 10ml lubricant, too much will make the belt slipping.Silicone oil once every 3 months.05 Safety NoticePlease keep your sight horizontal to avoid dizziness.More than one personto use the machine at same time is prohibited.Using machine with peg is prohibited.Trampling the machine head is prohibited.Walking sideways on the machine is prohibited.Walking backwards on the machine is prohibited.Please do not use the walking machine if you are aged people or pregnant women.Minors must be accompanied by an adult.HorizonCheck whether need to readjust after use 1 to 2 minutes.
17 18Beijing Kingsmith Technology Co., Ltd has patents of WalkingPad Walking Machine series products.This manual is created by Kingsmith and owns the copyright.Any form of unauthorized distribution, reproduction, publication, release or quotation by any institution or individual is prohibited without Kingsmith's written permission, not allow using the patents.This manual contains as much as possible functions and instructions for use when it is printed. However, due to pro-duct imperfections, design changes, etc., may still have discrepancies with the product you purchased. In view of pr-oduct updates, this manual and the actual product may vary in color, appearance, etc., actual supplies prevail.This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction conc-erning use of the appliance by a person responsible for their safety.Children should be supervised to ensure thatthey do not play with the appliance.This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazardsinvolved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by childr-en without supervision.07 Hazardous substances declaration 08 Trademark and Legal DeclarationThe table of Hazardous SubstancesX〇〇〇〇〇〇〇〇〇〇〇〇〇〇〇〇〇〇〇〇〇〇〇〇〇〇 〇 〇 〇This form has been prepared in compliance with the provisions of SJ/T 11364.○: Indicates that the content of said hazardous substance in all of the homogenous materials in the component is within the limits required by GB/T 26572.X: Indicates that the content of said hazardous substance excee-ds the limits required by GB/T 26572 in at least one homogenous material in the component.Part NameElectronic ComponentsMetal PartsShellBatteryOther PartsLead(Pb)Mercury(Hg)Cadmium(Cd)HexavalentChromium(Cr(VI))Polybrominated Biphenyls(PBB)Polybrominated diphenyl ethers(PBDE)Manufacturer: Beijing Kingsmith Technology Co., LtdAddress:Floor 4, Building 25, Area 18, ABP Park, Fengtai, Beijing, China. Product performance standard: Q/FTSMS0001-2017
Manufacturer: Beijing Kingsmith Technology Co., LtdAddress:Floor 4, Building 25, Area 18, ABP Park, Fengtai, Beijing, ChinaFCC ID: 2ARDB-WPA1F

Navigation menu