Beijing Kingsmith Technology WPA1F WalkingPad Walking Device User Manual
Beijing Kingsmith Technology Co.,Ltd WalkingPad Walking Device
User Manual
Model No.: WPA1F
User Manual
WalkingPad Walking Device
Please read this manual carefully before operating the product and keep it properly.
Content
1. Product and Accessories
2. Function schematic diagram
3. Guide for initial operation
4. Learn to use WalkingPad
5. Safety Notice
6. Maintenance and servicing
7. Hazardous substances declaration
8. Trademark and legal declaration 18
17
16
13
09
07
03
02
Caution: The user is cautioned that changes or modifications not expressly approved by
the party responsible for compliance could void the user's authority to operate the eq-
uipment.This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference, and (2) this
device must accept any interference received, including interference that may cause un-
desired operation.NOTE: This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy and,
if not installed and used in accordance with the instructions, may cause harmful interfer-
ence to radio communications. However, there is no guarantee that interference will not
occur in a particular installation.If this equipment does cause harmful interference to radio
or television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following mea-
sures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
-- Consult the dealer or an experienced radio/TV technician for help.
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment.This transmitter must not be co-located or operating in conjunction with any
other antenna or transmitter.
User Manual
01
Welcome to use
Main Product
01 Product and Accessories
Thank you for choosing WalkingPad
Walking Device
, hereinafter referred to as a WalkingPad, which posess various
advantages including exquisite, simple, innovative integral design. From now on, enjoy the quality life of walking at home.
Please carefully check whether the contents of the package are complete and intact. If there is any missing or
damaged, please contact the seller.
Power Cable Wrench Remote Controller Lanyard Silicone Oil
Other accessoriesParts
02
Expansion dimensions
Folding dimensions
The area of Walking belt
Gross weight
Net weight
Maximum load
Applicable age
Applicable height
Performance &indicators
Minimum speed
Maximum speed
Power Input
Rated voltage
Detailed parameters
Sport mode
822×547×129mm/
32.5"ｘ21.5"ｘ5"
1200×415mm/
47"ｘ16.5"
1432×547×129mm/
56.5"ｘ21.5"ｘ5"
68 Ibs / 31kg
62 lbs / 28kg
220 lbs / 100kg
12-60 years old
Unlimited
0.5 mi/hr 0.5 km/hr
3.75 mi/hr 6 km/hr
746W
110-120V~
Standby mode /
Fixed mode /Automatic mode
User Manual
03 04
Walking Belt
Fold Hinge
Roller
Power switch
Power plug
Roller
Mode Button
Display Panel
Mode Indicator Light
02 Function schematic diagram
1.Product main body
05 06
Fault Warning Light
Automatic Mode Manual ModeStandby Mode
Display Time Display Speed Show Distance Show Steps
2.Introduction of the function of the indicator panel 3.Walkingpad remote control
ACCELERATION
DECELERATION
MODE
START/STOP
LANYARD
BATTERY COVER
02 Function schematic diagram
07 08
9. Start to use the walker.7. Enter novice guide. 8.Complete learning to get all functions,
Otherwise, the Speed Limit is 1.75mi/hr,
3.75mi/hr can be unlocked after novice
guide.
03 Guide for initial operation
4. Connect the power line and turn
on the switch.
6. Open the App,follow the prompts
to set up the device.
1.Choose flat ground to place the
walkingpad. It is forbidden to place
it on a thick and soft cushion.
2. Unfold the walkingpad slowly
and press it down to completely
flat.
3.Check and adiust the walking
belt in the middle position .
10. If the belt deviates from the orbit in use,
please adjust properly. SEE: 06 Mainten-
ance and servicing.
5.Search "Walkingpad" App from
Apple Store or Android Google
Play and complete installation.
09
3. Instructions of fixed speed mode
control (primary mode)
04 Learn to use WalkingPad
1. Mode instruction
Standby Mode
Light of the Standby mode is on;
Motor and sensor stop response.
Fixed speed mode
Light of the fixed speed mode
is on; Control the speed through
the remote control or APP.
Automatic Mode
Light of the automatic mode is on;
Speed is automatically controlled by
intelligent algorithm.
2. Instructions of the standby
mode control.
The motor and sensor stop respo-
nding in this mode to prevent non-
users from accidentally triggering
the WalkingPad.
Mode Switch
Short press: return the previous mode.
Standby Mode Fixed speed mode
ACCELERATION
Short press: increase speed by 0.25mi.
START/STOP
Short press: start or stop the
WalkingPad
.
DECELERATION
Short press: reduce speed by 0.25mi.
MODE SWITCH
Short press: switch to automatic mode.
Long press: switch to standby mode.
10
In this mode, the speed of the WalkingPad can
be controlled by the remote control. It is re-
commended that beginners use the fixed speed
mode first and then use the automatic mode
after being skilled in using the WalkingPad.The
fixed speed mode is controlled by remote co-
ntrol by default, that is, the START/STOP button
of the remote control is used to start or stop the
WalkingPad, which can be modified in the client
“Personalized”.
4. Description of automatic mode control (advanced mode)
This mode is advanced mode, which is more
difficult and can be used completely without
the remote control. It is recommended for
users who have good sports coordination or
have walking machine experience.
Mode switch:
Short press: switch to the fixed speed mode
Long press: switch to the standby mode
Automatic Mode
04 Learn to use WalkingPad
5. Remote Controller Notice
If the remote controller has no
response or you change a new
one, The remote controller and
walking device need to
re-establishing communication.
Pairing method: Restart walking
device and short press the
MODE Button of Controller many
times during display "WAIT".
6. Fault Waming Linght
The Fault Warning Light is off when the
walking machine is working well. While
error occurs, the fault warning light is on
and the display panel shows the error code
E01：Drive communication fault
E02：Motor abnormalities
E05：Overcurrent protection
E06：Motor Protection
E08：Sensor Fault
E10: High temperature protection, automatic
recovery after the end of countdown.
E11:
Overload protection, please add lubricating
oil, and resume automatically after countdown.
Entering this area, the
WalkingPad will slow
down automatically
under the automatic
mode.
Entering this area, the
WalkingPad will start
or accelerate under
the automatic mode.
11 12
Short press: stop the
WalkingPad
.
Under this automatic mode,
set as the intelligent start
and stop, the WalkingPad
will start automatically to the
target speed(default is
1.75 mi/hr) while entering this
area.
13 14
05 Safety Notice
Please keep a rear distance of
50cm or more.
Please do not stand up on the
walking machine when it is un-
der power on and auto-calibrat-
ion situation.
Please choose sport shoes.
Using on uneven ground is
prohibited.
Anti-pinch Prohibition of vertical placement
Please keep a distance of
50cm or more for both sides.
Prohibition of lateral placement Please pull out the plug when
you’re not using it.
Anti-involved, please do
not trample.
Folding the machine if not power
off is prohibited.
It is strictly prohibited to walk up
and down the walking device
when running.
15 16
06 Maintenance and servicing
1. Clean the walking machine
2. Adjust the belt
3. Lubricate the Belt
Unplug the unit from the electrical source before you begin.
Pour a little gentle detergent in the cotton rag or towel. Don’t pour the
detergent on the belt directly, and don’t use acid or corrosive cleaners.
Wipe down the frame, motor encasement and belt. Don’t wipe backside of the belt.
After a period of using, the end part may appear dust and stains, that’s
normal situation, and just clean up.
Pressing both Mode Button and Acceleration Button on the remote controller over
3 seconds.
The display panel shows “CALI” and the speed is 2.5mi/hr(4km/h).
If belt moves left: Turn the left adjusting screw a half-circle clockwise.
If belt moves right: Turn the right adjusting screw a half-circle clockwise.
If belt is slipping: Turn both left and right adjusting screw a half-circle clockwise
at same time.
Unplug the unit from the electrical source before you begin.
Lift up the belt and apply the silicone to the underside surface of the belt.
Power on the walking machine.
Make the machine running with 2.5mi/hr(4km/h) 10 to 20 seconds.
No more 5 to 10ml lubricant, too much will make the belt slipping.
Silicone oil once every 3 months.
05 Safety Notice
Please keep your sight
horizontal to avoid
dizziness.
More than one person
to use the machine at
same time is prohibited.
Using machine with
peg is prohibited.
Trampling the machine
head is prohibited.
Walking sideways
on the machine is
prohibited.
Walking backwards
on the machine is
prohibited.
Please do not use the
walking machine if you
are aged people or
pregnant women.
Minors must be
accompanied by
an adult.
Horizon
Check whether need to readjust after use 1 to 2 minutes.
17 18
Beijing Kingsmith Technology Co., Ltd has patents of WalkingPad Walking Machine series products.
This manual is created by Kingsmith and owns the copyright.Any form of unauthorized distribution,
reproduction, publication, release or quotation by any institution or individual is prohibited without Kingsmith's written
permission, not allow using the patents.
This manual contains as much as possible functions and instructions for use when it is printed. However, due to pro-
duct imperfections, design changes, etc., may still have discrepancies with the product you purchased. In view of pr-
oduct updates, this manual and the actual product may vary in color, appearance, etc., actual supplies prevail.
This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction conc-
erning use of the appliance by a person responsible for their safety.Children should be supervised to ensure that
they do not play with the appliance.This appliance can be used by children aged from 8 years and above and
persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have
been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards
involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by childr-
en without supervision.
07 Hazardous substances declaration 08 Trademark and Legal Declaration
The table of Hazardous Substances
X〇
〇
〇
〇
〇
〇
〇
〇
〇
〇
〇
〇
〇
〇
〇
〇
〇
〇
〇
〇
〇
〇
〇
〇
〇
〇 〇 〇 〇
This form has been prepared in compliance with the provisions
of SJ/T 11364.
○: Indicates that the content of said hazardous substance in all
of the homogenous materials in the component is within the limits
required by GB/T 26572.
X: Indicates that the content of said hazardous substance excee-
ds the limits required by GB/T 26572 in at least one homogenous
material in the component.
Part Name
Electronic
Components
Metal Parts
Shell
Battery
Other Parts
Lead
(Pb)
Mercury
(Hg)
Cadmium
(Cd)
Hexavalent
Chromium
(Cr(VI))
Polybrominated
Biphenyls
(PBB)
Polybrominated
diphenyl ethers
(PBDE)
Manufacturer: Beijing Kingsmith Technology Co., Ltd
Address:Floor 4, Building 25, Area 18, ABP Park, Fengtai, Beijing, China.
Product performance standard: Q/FTSMS0001-2017
Manufacturer: Beijing Kingsmith Technology Co., Ltd
Address:Floor 4, Building 25, Area 18, ABP Park, Fengtai, Beijing, China
FCC ID: 2ARDB-WPA1F