Belkin F5D6130 Wireless Access Point User Manual Revised Manual

Belkin International, Inc. Wireless Access Point Revised Manual

Revised Manual

Quick Installation GuideofWLAN 11Mbps Access PointWA3001AEumitcomEumticom Technlolgy Inc.
2Federal Communications Commission StatementThis device complies with FCC Rules Part 15. Operation is subject to the followingtwo conditions:This device may not cause harmful interference.This device must accept any interference received, including interference that maycause undesired operation.This equipment has been tested and found to comply with the limits for a Class B digital device,pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protectionagainst harmful interference in a residential installation. This equipment generates, uses and canradiate radio frequency energy. If this equipment is not installed and used in accordance with themanufacturer's instructions, it may cause harmful interference to radio communications. However,there is no guarantee that interference will not occur in a particular installation. If this equipmentdoes cause harmful interference to radio or television reception, which can be determined by duringthe equipment off and on, the user is encouraged to try to correct the interference by one or moreof the following measures:! Reorient or relocate the receiving antenna.! Increase the separation between the equipment and receiver.! Connect the equipment to an outlet on a circuit different from thatto which the receiver is connected.! Consult the dealer or an experienced radio/TV technician for help.The use of shielded cables for connection of the monitor to the graphics card isrequired to assure compliance with FCC regulations. Changes or modifications tothis unit not expressly approved by the party responsible for compliance could voidthe user's authority to operate this equipment.Manufacturer's Disclaimer StatementThe information in this document is subject to change without notice and does notrepresent a commitment on the part of the vendor. No warranty or representation, eitherexpressed or implied, is made with respect to the quality, accuracy or fitness for anyparticular purpose of this document. The manufacturer reserves the right to makechanges to the content of this document and/or the products associated with it at any timewithout obligation to notify any person or organization of such changes. In no event willFCC RF Radiation Exposure Statement:This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolledenvironment. This equipment should be installed and operated with a minimum distance of20 centimeters between the radiator and your body.This transmitter must not be co-located or operating in conjunction with any other antenna ortransmitter.
3the manufacturer be liable for direct, indirect, special, incidental or consequential damagesarising out of the use or inability to use this product or documentation, even if advised ofthe possibility of such damages. This document contains materials protected by copyright.All rights are reserved. No part of this manual may be reproduced or transmitted in anyform, by any means or for any purpose without expressed written consent of its authors.Product names appearing in this document are mentioned for identification purchases only.All trademarks, product names or brand names appearing in this document are registeredproperty of their respective owners.This device requires a radio license, unless it (including antenna ) is installed totallyinside a building. (User must obtain this license from Industry Canada ).“To reduce potential radio interference to other users, the antenna type and its gainshould be so chosen that the equivalent isotropically radiated power (EIRP) is notmore than that required for successful communication.” Printed in Taiwan
1IntroductionWA3001A is an 11Mbps Access Point that bridges between wired Local AreaNetwork and one or more wireless mobile PC based stations. Connected to theEthernet backbone through RJ-45 connector, the single Access Pointwirelessly provides multiple data access with verity of mobile desktop orlaptop PC in covered propagation range. The Serial of Wireless LAN productsoffer a fast, reliable, cost-effective solution.I. Release package1. One Access Point2. One Power Adapter (9V/1.11A)3. One Floppy Diskette
2II. Hardware Installation1. Connect the AP RJ45 port to a Ethernet 10BaseT Hub.2. Connect the power adapter to power source and plug it into power hole ofAP.III. Software InstallationFollowing descriptions describe the steps to install the AP Utility1. Power on the PC and boot it to the windows system2. Insert the floppy diskette to the floppy driver.3. Type the “A:\Utility\setup.exe” to start the Installation.4. Follow the setup wizard to complete the setup process.IV. Access Point Setup and ConfigureAfter AP Utility is installed, you may start to setup and configure the AP. Youcould choose to configure the AP through the Ethernet or WLAN. If you wantto configure the AP by WLAN, you should have a WLAN PC or PCI adapterinstalled and associate with the AP in advance. The default SSID of AP is“WLAN”.1. Lunch the WLAN AP Utility program from “ Access Point Utility” Folder.2. Click item “Scan” under the menu item “AP” in the utility program tosearch the AP in network.
33. If an AP is detected, the utility program will show the AP information .4. Double click the found AP from the list table.5. Input the IP Address, subnet mask and default gateway correctly, clickthe “OK” button, you MUST assign the AP IP address with the valuethat is located within the same subnet of the configured PC.V. Hardware SpecificationRadio: Complies with IEEE 802.11Frequency Band: 2400 ~ 2483.5MHz ( for US, Canada, and ETSI) 2400 ~ 2497MHz (for Japan)Modulation TYPE: CCK,BPSK,QPSKOperating Channels: IEEE 802.11 compliant 11 channels (US, Canada) 13 channels (ETSI) 14 channels (Japan)Radio Technology: Direct Sequence Spread SpectrumData Rate: 1 / 2 / 5.5 / 11 MbpsOutput Power: > +15dBmReceive sensitivity: Min. -78dBm for 11Mbps; Min. -82dBm for 5.5/2/1 Mbps ;(@BER 10E-5)Ethernet :Wired Interface : Ethernet IEEE 802.3 10 BaseT Current Consumption : 5V, 750 m A Max.
4Notice : Eumitcom Technology Inc. reserves the right to changespecifications detailed in this document at any time without notice, andassumes no responsibility for any errors within this document.EumitcomEumitcomEumitcomEumitcomEumitcom Technology Inc.2F, No. 2, Li Hsin Rd., Science-Based Industrial ParkHsinchu 300, Taiwan, R.O.C.Tel : 886-3-5785717 Fax : 886-3-5785817Http://www.eumitcom.com

Navigation menu