Belkin F5D6130 Wireless Access Point User Manual Revised Manual

Download:
Mirror Download [FCC.gov]
Document ID	178372
Application ID	hDxtYXP+blhVf3mp6maklw==
Document Description	Revised Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	1.97kB (24645 bits)
Date Submitted	2001-11-08 00:00:00
Date Available	2001-11-08 00:00:00
Creation Date	2001-03-14 11:32:32
Producing Software	Acrobat Distiller 4.0 for Windows
Document Lastmod	2001-11-08 10:45:57
Document Title	Revised Manual

Eumitcom
Eumticom Technlolgy Inc.
Quick Installation Guide
of
WLAN 11Mbps Access Point
WA3001A
Federal Communications Commission Statement
This device complies with FCC Rules Part 15. Operation is subject to the following
two conditions:
This device may not cause harmful interference.
This device must accept any interference received, including interference that may
cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection
against harmful interference in a residential installation.
This equipment generates, uses and can
radiate radio frequency energy. If this equipment is not installed and used in accordance with the
manufacturer's instructions, it may cause harmful interference to radio communications.
there is no guarantee that interference will not occur in a particular installation.
However,
If this equipment
does cause harmful interference to radio or television reception, which can be determined by during
the equipment off and on, the user is encouraged to try to correct the interference by one or more
of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment to an outlet on a circuit different from that
to which the receiver is connected.
! Consult the dealer or an experienced radio/TV technician for help.
The use of shielded cables for connection of the monitor to the graphics card is
required to assure compliance with FCC regulations. Changes or modifications to
this unit not expressly approved by the party responsible for compliance could void
the user's authority to operate this equipment.
FCC RF Radiation Exposure Statement:
This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with a minimum distance of
20 centimeters between the radiator and your body.
This transmitter must not be co-located or operating in conjunction with any other antenna or
transmitter.
Manufacturer's Disclaimer Statement
The information in this document is subject to change without notice and does not
represent a commitment on the part of the vendor. No warranty or representation, either
expressed or implied, is made with respect to the quality, accuracy or fitness for any
particular purpose of this document. The manufacturer reserves the right to make
changes to the content of this document and/or the products associated with it at any time
without obligation to notify any person or organization of such changes. In no event will
the manufacturer be liable for direct, indirect, special, incidental or consequential damages
arising out of the use or inability to use this product or documentation, even if advised of
the possibility of such damages. This document contains materials protected by copyright.
All rights are reserved. No part of this manual may be reproduced or transmitted in any
form, by any means or for any purpose without expressed written consent of its authors.
Product names appearing in this document are mentioned for identification purchases only.
All trademarks, product names or brand names appearing in this document are registered
property of their respective owners.
This device requires a radio license, unless it (including antenna ) is installed totally
inside a building. (User must obtain this license from Industry Canada ).
“To reduce potential radio interference to other users, the antenna type and its gain
should be so chosen that the equivalent isotropically radiated power (EIRP) is not
more than that required for successful communication.”
Printed in Taiwan
Introduction
WA3001A is an 11Mbps Access Point that bridges between wired Local Area
Network and one or more wireless mobile PC based stations. Connected to the
Ethernet backbone through RJ-45 connector, the single Access Point
wirelessly provides multiple data access with verity of mobile desktop or
laptop PC in covered propagation range. The Serial of Wireless LAN products
offer a fast, reliable, cost-effective solution.
I.
Release package
1. One Access Point
2. One Power Adapter (9V/1.11A)
3. One Floppy Diskette
II.
Hardware Installation
1. Connect the AP RJ45 port to a Ethernet 10BaseT Hub.
2. Connect the power adapter to power source and plug it into power hole of
AP.
III.
Software Installation
Following descriptions describe the steps to install the AP Utility
1. Power on the PC and boot it to the windows system
2. Insert the floppy diskette to the floppy driver.
3. Type the “A:\Utility\setup.exe” to start the Installation.
4. Follow the setup wizard to complete the setup process.
IV.
Access Point Setup and Configure
After AP Utility is installed, you may start to setup and configure the AP. You
could choose to configure the AP through the Ethernet or WLAN. If you want
to configure the AP by WLAN, you should have a WLAN PC or PCI adapter
installed and associate with the AP in advance. The default SSID of AP is
“WLAN”.
1. Lunch the WLAN AP Utility program from “ Access Point Utility” Folder.
2. Click item “Scan” under the menu item “AP” in the utility program to
search the AP in network.
3. If an AP is detected, the utility program will show the AP information .
4. Double click the found AP from the list table.
5. Input the IP Address, subnet mask and default gateway correctly, click
the “OK” button, you MUST assign the AP IP address with the value
that is located within the same subnet of the configured PC.
V.
Hardware Specification
Radio:
Frequency Band:
Modulation TYPE:
Operating Channels:
Radio Technology:
Data Rate:
Output Power:
Receive sensitivity:
Ethernet :
Wired Interface :
Complies with IEEE 802.11
2400 ~ 2483.5MHz ( for US, Canada, and ETSI)
2400 ~ 2497MHz (for Japan)
CCK,BPSK,QPSK
IEEE 802.11 compliant
11 channels (US, Canada)
13 channels (ETSI)
14 channels (Japan)
Direct Sequence Spread Spectrum
1 / 2 / 5.5 / 11 Mbps
> +15dBm
Min. -78dBm for 11Mbps; Min. -82dBm for 5.5/2/1
Mbps ;(@BER 10E-5)
Ethernet
IEEE 802.3 10 BaseT
Current Consumption : 5V, 750 m A Max.
Notice :
Eumitcom Technology Inc. reserves the right to change
specifications detailed in this document at any time without notice, and
assumes no responsibility for any errors within this document.
Eumitcom
Eumitcom Technology Inc.
2F, No. 2, Li Hsin Rd., Science-Based Industrial Park
Hsinchu 300, Taiwan, R.O.C.
Tel : 886-3-5785717 Fax : 886-3-5785817
Http://www.eumitcom.com

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.3
Linearized                      : No
Encryption                      : Standard V1.2 (40-bit)
User Access                     : Print, Copy, Fill forms, Extract, Assemble, Print high-res
Create Date                     : 2001:03:14 11:32:32
Producer                        : Acrobat Distiller 4.0 for Windows
Modify Date                     : 2001:11:08 10:45:57+08:00
Page Count                      : 7
Has XFA                         : No

EXIF Metadata provided by EXIF.tools