Belkin F5D6131 Wireless Access Point User Manual P73829 A F5D6130 man

Download:
Mirror Download [FCC.gov]
Document ID	330615
Application ID	fJJ29WIyv7GFXUmi2nrECA==
Document Description	User manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	128.38kB (1604809 bits)
Date Submitted	2003-06-06 00:00:00
Date Available	2003-06-06 00:00:00
Creation Date	2001-12-07 16:43:47
Producing Software	Acrobat Distiller 4.0 for Macintosh
Document Lastmod	2003-05-29 16:56:03
Document Title	P73829-A_F5D6130-man.qxd
Document Creator	QuarkXPressª: LaserWriter 8 8.7
Document Author:	danas

Wireless Network
Access Point
User Manual
F5D6130
Table of Contents
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1–2
Product Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Knowing your Belkin Wireless Access Point . . . . . . . . . . . . . . . . . 4–5
Quick Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6–7
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8–10
Installing the Wireless Access Point Manager Software . . . . . . . 11–12
Using the Belkin Wireless Access Point Manager . . . . . . . . . . . 13–21
Wireless Networking Using 802.11b . . . . . . . . . . . . . . . . . . . . 22–25
Glossary of Wireless Networking Terms . . . . . . . . . . . . . . . . . . 26–27
Glossary of Wired Networking Terms . . . . . . . . . . . . . . . . . . . 28–29
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32-33
Introduction
Thank you for purchasing the Belkin 11Mbps Wireless Access Point (WAP)
and welcome to the world of wireless networking. Now you can take
advantage of this great new technology and gain the freedom you need
around the home or office without using cables. The WAP acts as a bridge
between your existing wired network and your wireless equipped
computers. The easy installation and setup will have you networking
wirelessly in minutes. Please be sure to read through this manual
completely to be sure that you are getting the most out of your WAP.
Key Features
Wide Area Coverage at High Speeds
The Belkin WAP provides coverage over an indoor area up to 300 feet in
radius and an outdoor area over 1,800 feet in radius.
Up to 128-bit Security Encryption
Your Belkin WAP is capable of encrypting (scrambling) the transmitted radio
waves so you can be sure that your data is secure. The optional encryption
feature allows you to encrypt at 64-bits or 128-bits using a key that you
enter yourself.
MAC Address Filtering
For added security, you can set up a list of MAC addresses (unique client
identifiers) that are allowed access to your wireless network. Every computer
equipped with a wireless network adapter has its own MAC address. Simply
enter these MAC addresses into a list using the Belkin Wireless 802.11b
Network Manager software, and access to your network through the WAP is
restricted to only those MAC addresses.
Introduction
Applications
• Wireless roaming with a laptop around the home or office
Gain the freedom you need around the home or office with no cables.
• Difficult-to-wire environments
For use in buildings with solid or finished walls or open areas where
wiring is difficult to employ.
• Frequently Changing Environments
Offices or environments that frequently rearrange the workplace and
change location.
• Temporary LANs for special projects or peak time
Trade shows, exhibitions, and construction sites that need a network on
a temporary basis. Companies that need additional workstations for a
peak activity period.
• SOHO (Small Office/Home Office)
SOHO users who need easy and quick setup.
Package Contents
• Belkin Wireless Network Access Point
• Power Supply
• Belkin 802.11b Wireless Manager Software
• User Manual
System Requirements
• At least one computer equipped with an 802.11b compliant wireless
Ethernet adapter
• TCP/IP networking protocol installed on each computer
Product Specifications
Specifications
Wireless Standard:
802.11b
Radio Technology:
Direct Sequence Spread Spectrum (DSSS)
Operating Channels:
IEEE 802.11 compliant
11 channels (US, Canada)
13 channels (ETSI)
14 channels (Japan)
Data Rate:
11, 5.5, 2, 1Mbps per channel (Auto-Rollback)
Typical Indoor
Operating Range:
590 ft.(180M) @ 11Mbps
984 ft.(300M) @ 5.5Mbps
1476 ft.(450M) @ 2Mbps
1800 ft.(550M) @ 1Mbps
Network Standards:
IEEE 802.3 10BaseT
LED Indicator:
Link, Activity, and Power
Frequency Band:
ISM Band, 2400 ~ 2483.5MHz
Modulation Type:
QPSK, BPSK, CCK
Data Rate:
1/2/5.5/11Mbps per channel
Protocol:
CSMA/CA (Collision Avoidance) with ACK
Output Power:
13dBm ~ 20dBm (50 mW) (max.)
Receive Sensitivity:
Min. -78dBm for 11Mbps @BER 10E-5;
Min. -82dBm for 5.5/2/1Mbps @BER 10E-5
Encryption:
64/128-bit WEP (Wired Equivalent Privacy)
Antenna Type:
2dBi (max.) @ External PCB patch diversity antenna
Power Consumption:
5V, 750mA max.
Physical Dimensions:
114.5 x 54 x 5.0mm
Weight:
50 g
OS Support:
Windows® 95 (OSR2), 98, 2000, NT,
Millennium Edition
Certification:
FCC Class B, CE Mark, C-Tick
Knowing your Belkin Wireless Access Point
Ethernet
Link/Activity LED
Transmit/Receive LED
Power LED
Power LED
Indicates that the WAP is receiving power
Transmit/Receive LED
Flashing Green: Indicates data is being transmitted
Flashing Amber: Indicates data is being received
Ethernet Link/Activity LED
Solid Green: Indicates a valid Ethernet (Wired) cable link
Flashing Orange: Indicates Ethernet (Wired) activity
Knowing your Belkin Wireless Access Point
Rotatable Dual
Dipole Antennas
DC Power Jack
RJ45 Ethernet
Jack
DC Power Jack
Connect the 9V DC connector from the power supply to this jack.
RJ45 Ethernet Jack
Connect an Ethernet cable to this socket, and connect to an open RJ45
10BaseT port on a switch or hub.
Rotatable Dual Dipole Antennas
Two unidirectional dipole antennas are located on the side of the WAP. The
antennas can rotate 360 degrees. The antennas should be oriented in the
vertical position for best operation.
Quick Setup
Quick Setup—Connecting the WAP to your
existing network
The factory settings of the Belkin WAP were chosen to get you up and
running quickly.
Desktop PC
Desktop PC
Cable/DSL
Modem
Notebook with Wireless
Notebook Network Card
Belkin Router
or Switch
Wireless
Access Point
Notebook with Wireless
Notebook Network Card
Step 1: Installation Site Selection
In general, the best location to place the WAP is at the center of your wireless
coverage area, within line-of-sight of all wireless stations. Ensure all stations are
within the service range of the WAP.
Step 2: Hardware Setup
1.Connect your wired LAN to the WAP via a 10Mbps connection using a
Category 3 or Category 5 cable with a standard RJ45 connector (not a
Quick Setup
crossover cable). This connection from your wired LAN would come from
a hub or switch connected to your LAN or a cable/DSL router.
2.Connect the external power supply to the 5V DC socket on the rear panel
of the WAP.
Step 3: Install the Belkin WAP Manager Software
1.Insert the CD into the CD-ROM drive.
2.Access your CD-ROM drive by double-clicking on the CD-ROM icon in
the "My Computer" window. Double-click on the "Setup" icon and follow
the directions in the installation wizard.
Step 4: Configure the Wireless-Equipped Computer(s) to Communicate with
the WAP
1.Start up the wireless-equipped computer and configure the
wireless-equipped PC to connect to an SSID of "WLAN" or "Any".
2.If not done already, configure the wireless-equipped PC to "Obtain IP
Address Automatically".
3.Restart the wireless-equipped PC.
Your Belkin WAP is now fully configured. To configure advanced features,
please reference the Installation section.
Default Settings:
WAP Parameter
AP Name
SSID
Channel
RTS Threshold
IP Address
Subnet Mask
Default Gateway
DHCP Client
Encryption
MAC Address Filter
Password
Default Value
MiniAP
WLAN
11
2346
192.168.0.254
255.255.255.0
0.0.0.0
Enabled
Disabled
Disabled
MiniAP (case-sensitive)
Installation
Selecting an appropriate site for your WAP
Selecting an appropriate site for your WAP will ensure the best
performance. First, a few rules of thumb:
• Avoid locating the WAP near metal objects such as appliances like
refrigerators, ovens, and washer/dryers. Keep in mind that your
appliances may be on the other side of the wall in the area that you
may be considering to locate the WAP.
• For best performance, locate the WAP as close to the center of the area
that you will be covering. Keep in mind that radio waves radiate
outward from the WAP in a circular pattern. Typical range is 100-150
feet indoors at 11Mbps. If the area you wish to cover is smaller than
200-300 feet wide, then locating the WAP in the center of the area
becomes less critical.
• Normally, the higher that you locate the WAP, the better the
performance and range will be. However, in an area such as an
average-sized house or small office, height is less critical.
• Remember that many things can cause a degrade of the radio signal
such as brick walls, metal-reinforced concrete, the metal housing of
appliances, or even wiring in the walls.
Connecting the WAP to a cable/DSL router, Ethernet
switch, or hub
1. Select a suitable site for your WAP.
2. Connect a CAT5 cable between the WAP and your cable/DSL
router’s LAN port, Ethernet switch, or hub by plugging one end of
the cable into the RJ45 jack on the WAP and the other end into an
open RJ45 jack on the cable/DSL router, Ethernet switch, or hub.
3. Connect the power supply to the WAP by plugging the round DC
connector into the DC jack on the WAP. Plug the power supply into
the wall. Verify that the Power LED and the Link LED are
illuminated. If both LEDs are illuminated, this indicates that the
WAP is connected properly.
4. Place the WAP on a desktop or mount it to a wall in the location
that you have chosen. Next, swivel the antennas so they are both
pointing up.
Installation
Connection and placement of your WAP is now complete. Go to
"Installing the WAP Manager Software" to learn how to configure
the WAP.
Desktop PC
Desktop PC
Cable/DSL
Modem
Wireless Notebook
Network Card
Belkin Router
or Switch
Wireless
Access Point
Wireless Notebook
Network Card
Fig. 1 Connecting the WAP to a cable/DSL router, Ethernet switch, or hub
Installation
Using the WAP to expand local coverage
The WAP can act as a central point of communication of your
wireless-equipped computers without connecting it to a wired network. Using
the WAP in this manner will effectively double the range between your
wireless-equipped computers by relaying the data from one computer to
another. Simply locate the WAP in the center of the area you will be
operating your network. The diagram below illustrates this concept.
Notebook Wireless
Notebook Network Card
Wireless
Access Point
Notebook with Wireless
Notebook Network Card
PC with Wireless Desktop
PCI Network Adapter
10
Installing the Wireless Access Point Manager Software
The Belkin 802.11b Wireless Manager Software allows you to connect to
the WAP and make changes to the configuration. Follow these steps to
install the software.
1. Insert the Belkin Wireless Network Access Point “CD-ROM” into your
CD-ROM drive.
2. Access your CD-ROM drive by double-clicking on the “CD-ROM” icon in
the “My Computer” window. Double-click on the “Setup” icon to start the
installation process.
3. The following screen will appear. Click "Next".
4. The installer will install the needed files to a folder named
"C:\Belkin\Belkin Wireless Access Point". If you wish to change this, click
"Browse" and select a folder. Click "Next" to continue.
11
Installing the Wireless Access Point Manager Software
5. The installer will create a
program folder called "Belkin
Wireless Access Point
Manager". If you wish to
change this, enter a name or
select from the list below.
Click "Next" to continue.
6. Click "Finish" to complete
the installation.
Start the WAP Manager Software by clicking "Start", "Programs", then
select "Belkin Wireless Access Point Manager", then click on "Belkin
Wireless Access Point Manager".
12
Using the Belkin Wireless Access Point Manager
Once you launch the WAP Manager Software, a window will open and begin
scanning for your WAP. The words "Scanning AP" will be displayed in the
bottom right corner of the window. When finished scanning, "Scanning
complete" will be displayed. You can connect to the WAP from any computer
on the network that is either wired or wireless. Your WAP is shipped from the
factory with the name "MiniAP". Instructions to change this are covered later in
this manual. If your WAP is installed properly, you should see the name
"MiniAP" in the “Wireless Manager” window when scanning has completed. If
not, see troubleshooting tips at the end of this manual.
Connecting to the WAP
To make any changes to the configuration of the WAP, you must connect to
the WAP by entering a password. The WAP is password-protected to keep
unauthorized users from changing settings.
1. Click on "Command" and select "Connect AP…" in the drop-down menu.
13
Using the Belkin Wireless Access Point Manager
2. The "Input Password" window will appear. Your WAP ships from the factory
with the password set to "MiniAP". Keep in mind that the password is casesensitive, and enter the password.
Password = "MiniAP" (case-sensitive)
3. When connected, the word "Connected" will appear under the column
labeled "State". If you cannot connect, see the troubleshooting tips at the
end of this manual.
Configuring to the WAP
The WAP can be configured for many different parameters—from setting the
password to enabling the encryption. To configure the WAP, click on
"Command" and select "Configure AP".
14
Using the Belkin Wireless Access Point Manager
The "AP Setting" screen will appear.
This screen displays the WAP’s status and settings.
Fixed Parameters
BSSID
This displays the MAC address of the adapter. The MAC address is fixed
and cannot be changed.
Regulation Domain
Each country’s regulatory commission (FCC for the US) has specified a
specific set of channels for 802.11b to operate on. Each country is
different. To comply with the standards for each country, the WAP is
programmed at the factory for the proper regulatory domain. The
regulatory domain is fixed and cannot be changed.
WEP
This displays the status of the WEP encryption. Disabled = OFF. Enabled =
ON.
Associated Stations
This indicates the number of wireless clients (computers) connected to the
WAP. A total of 64 wireless clients can be connected at a single time.
15
Using the Belkin Wireless Access Point Manager
Firmware Version
Displays the version of firmware programmed into the WAP. Belkin may
from time to time upgrade the firmware and provide it, at no cost, for
download from the Belkin website. For more on upgrading the firmware,
visit www.networking.belkin.com/update.
Programmable Parameters
AP Name
The AP Name is used to help identify an WAP when multiple APs are
being used. For instance, in a large building using 20 APs, the names may
be "AP 1:WEST ROOM", or in a large house, "AP 5:Kitchen". To enter a
name, click in the name field and enter a name. When finished making
changes, click "Save" for the changes to take effect.
SSID
The Service Set Identifier (SSID) is like a name for the wireless network
and is sometimes called the "Network Name". All WAPs in a wireless
network should be set to the same SSID to enable clients to roam from
WAP to WAP. The wireless-equipped computers in the wireless network
should also be set to the same SSID to gain access to the network. The
default setting is "WLAN" (Wireless Local Area Network). To change the
SSID, simply click in the SSID field and enter a new SSID. When finished
making changes, click "Save" for the changes to take effect.
Channel
The 802.11b wireless standard supports up to 14 channels. The number of
available channels are limited to local regulations that determine which
channels are available. (FCC/IC: Channels 1-11; ETSI: Channels 1-13;
France: Channels 10-13; Spain: Channels 10-11; MKK: Channels 1-14.)
The default channel is 11. To change the channel, click the UP/DOWN
arrows next to the channel field. When finished making changes, click
"Save" for the changes to take effect.
RTS Threshold
This is the rate at which errors are checked. We recommend not
changing this.
16
Using the Belkin Wireless Access Point Manager
IP Address
An IP address can be manually entered. The default IP address is
192.168.0.254. To enter the IP address, click in the “IP Address” field and
enter the IP address.
Subnet Mask
A Subnet Mask can be manually entered. The default Subnet Mask is
255.255.255.0. To enter the Subnet Mask, click in the “Subnet Mask” field
and enter the Subnet Mask.
Default Gateway
A Default Gateway address can be manually entered. The Default
Gateway address is 0.0.0.0. To enter a Default Gateway address, click in
the “Subnet Mask” field and enter the Default Gateway address.
DHCP Client
The WAP can obtain an IP address, Subnet Mask, and Default Gateway
information automatically in a dynamic network environment. The default
setting is "Enabled". If the WAP is connected to a network that does not
employ DHCP, the default IP address, Subnet Mask, and Default Gateway
will be used. To enable or disable the DHCP Client, click on the down
arrow and select "Enabled" or "Disabled". When finished making changes,
click "Save" for the changes to take effect.
Security
The WAP features some methods of keeping your wireless network secure.
Using these methods can greatly increase your security and peace of mind.
Method 1: Encryption
For secure data transmissions, the Belkin WAP is capable of encrypting, or
"scrambling", the information that is sent over the air between your
computers. The WAP uses a form of encryption called WEP (Wired
Equivalent Privacy). There are two levels of WEP encryption—64-bit and
128-bit. As the numbers imply, 128-bit encryption is more secure than 64bit encryption. However, using 128-bit encryption can slow down the rate
at which data is sent between the wireless-equipped computers and the
WAP. WEP encryption uses keys to scramble and unscramble the data that
is being sent between wireless-equipped computers and the WAP. The
17
Using the Belkin Wireless Access Point Manager
WAP and the computers must use the same key to be able to communicate
using encryption. For more information, go to the section called “Using
WEP Encryption”.
Method 2: MAC Address Filtering
The WAP can be programmed with a list of MAC addresses that are
allowed to connect to the WAP. A MAC address is a unique "serial number"
that is assigned to every wireless adapter. For instance, if you own a Belkin
F5D6020 Wireless Notebook Network Adapter for your laptop, it has been
assigned its own MAC address at the factory. The MAC address is located
on a small sticker on the bottom of the product. Programming the WAP
with this MAC address and enabling the MAC address filtering feature lets
you manage which computers are allowed to connect to the WAP.
Using WEP Encryption
In the “Configuration” menu, click "Encryption". The following screen
will appear.
Select “64-bit” from the drop-down menu.
You will notice when using 64-bit
encryption, there are four keys labeled
"Key 1" through "Key 4". Only one key can
be used at a time. Keys can be entered
manually, but for ease-of-use, the software
can generate keys using a "passphrase" that
you enter. This passphrase can be easily
distributed to wireless-equipped computer
users in your network. For instance, creating
a key using the passphrase "Passphrase"
generates four keys in 64-bit encryption
mode and one key in 128-bit encryption mode. Users of laptops need only to
enter the passphrase and the key number into their computers’ wireless
management software to be able to communicate while using encryption. All
computers on the network must use the same encryption rate and passphrase.
The passphrase can be changed as often as desired.
18
Using the Belkin Wireless Access Point Manager
Setting 64-bit Encryption
1. Select 64-bit from the drop-down menu.
2. Select "Create with Passphrase".
3. Enter a passphrase and click "Apply".
4. Select the "Default Key ID" from the
drop-down menu. These are labeled
1–4. Click "Apply".
64-bit encryption is now enabled in the
WAP. Each wireless-equipped computer
(client) that needs to communicate with the
WAP must be set to the same encryption settings.
Setting 128-bit Encryption
1. Select 128-bit from the drop-down menu.
2. Select "Create with Passphrase".
3. Enter a passphrase and click "Apply".
128-bit encryption is now enabled in the
WAP. Each wireless-equipped computer
(client) that needs to communicate with
the WAP must be set to the same
encryption settings.
Using MAC Address Filtering
1. To set up the MAC filtering, click on "Command" and select
"Set MAC Filter".
19
Using the Belkin Wireless Access Point Manager
2. The “MAC Address Filter”
screen will appear. The WAP
comes from the factory with the
MAC Address Filter disabled. To
enable the filtering, select
“Enabled” from the
drop-down menu.
3. In the field next to "<
Source Exif Data: 
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
Encryption                      : Standard V1.2 (40-bit)
User Access                     : Print, Fill forms, Extract, Assemble, Print high-res
Create Date                     : 2001:12:07 16:43:47Z
Modify Date                     : 2003:05:29 16:56:03+08:00
Page Count                      : 37
Creation Date                   : 2001:12:07 16:43:47Z
Producer                        : Acrobat Distiller 4.0 for Macintosh
Author                          : danas
Mod Date                        : 2003:05:29 16:56:03+08:00
Metadata Date                   : 2003:05:29 16:56:03+08:00
Creator                         : danas
Title                           : P73829-A_F5D6130-man.qxd

EXIF Metadata provided by EXIF.tools