Belkin F8E825-USB Mini Wireless Optical Mouse User Manual P74211 A F8E825 USB man

Belkin International, Inc. Mini Wireless Optical Mouse P74211 A F8E825 USB man

User Manual

MiniWireless Optical MouseNavigate your notebook with optical precision and wireless freedomUser ManualF8E825-USBBATTERY INSTALLATION1. Press and hold the bottom release tab as youslide the top cover off. (fig. 1)2. Insert 2 AAA batteries. (fig. 1-2)3. Replace the top cap and close it. !CAUTION:•Be sure to check polarity (+ or – sign) andinsert battery properly.•Make sure battery type is AAA alkaline (1.5V).•Remove the batteries if mouse will not be in use for a long time.•Each time you replace the batteries, repeat themouse setup by following the “setup forlinkage” (fig. 5).HARDWARE INSTALLATION1. Shut down the computer. 2. Connect the receiver either directly or with theUSB extension cable to the USB port on the PC.(fig. 2)3. Place the receiver beside the notebook ordesktop PC. (fig. 3)4. Turn on the PC.5. Switch on the power of the wireless mouselocated on the backside of the mouse. (fig. 4)!CAUTION:While traveling, please switch off the unit to savebattery power. (fig. 4)DRIVER INSTALLATION1. Insert the installation CD into your CD-ROM drive.2. The CD should automatically load theinstallation. If it does not load, click “Start”then “Run”, then type “X:\setup” (replace “X”with the correct drive letter for your CD-ROMdrive, usually D). Then follow through the on-screen instructions to complete theinstallation.3. When the setup is complete, the system willrestart automatically. It will show a mouse iconin the bottom right-hand corner of the screen.!CAUTION:Some computers running Windows® 98 will requireinsertion of the Windows 98 CD to finish theinstallation of the driver.ID SETUP1. Aim the front point of the mouse at the receiver.2. IMPORTANT: FIRST, PRESS THE CONNECTBUTTON OF THE MOUSE; THEN PRESS THECONNECT BUTTON OF THE RECEIVER (fig. 5).NEVER REVERSE THIS PROCEDURE.3. When the connect button of the receiver ispressed, the LED inside the receiver willlight. As soon as the linkage is completed, theLED will go off.4. The setup must be completed within oneminute. If setup time exceeds one minute,repeat procedure. BUTTON FUNCTION SETUP1. Start the setup from the Control Panel ordirectly click on the mouse icon at the bottomright corner of the screen. It shows thefollowing functions: -Button: set up for either right or left hand,and adjust the speed -Wheel: set up the functions for hot keys and zooming-Motion: set up the speed of the mouse pointer2. After the function is set up, press “Yes” to storethe new setup.SETUP FOR MULTI-USERSWhen using more than one MiniWireless OpticalMouse in the same location, set up one mouse at atime. You must complete the setup for each mousebefore beginning the next.ENVIRONMENTTo avoid environmental interference, which willshorten the effective operation distance, pleasenote the following:1. Do not put the mouse and receiver on a metalcabinet or desk. Metal creates RF interference,which may impair the RF communication andshorten the communication distance. 2. Keep a distance of more than 1.5m betweenfig. 1fig. 4fig. 3fig. 2fig. 5fig. 1-2press upP74211-A_F8E825-USB man.qxd 7/8/03 5:06 PM Page 1
your mouse and another operational RF deviceto avoid interference.3. The optical sensor of the mouse will not workcorrectly if placed on a mirror, glass, or on anyreflecting or half-tone painted surface. TROUBLESHOOTINGThe cursor doesn’t react when I move the mouse.1. This is probably because the distance betweenthe receiver and mouse exceeds the workingrange. Simply adjust so that the mouse is closerto the receiver. 2. Make sure that the mouse is not placed on areflective surface such as a mirror, glass, half-tone painted surface, or on a 3D mousepad. When using this wireless device on a metal table or near metal furniture, use a non-reflective, thick mouse pad to reduce thepotential for interference.3. Your ID setup may not have worked properly.Please repeat the ID setup process. TECHNICAL SPECIFICATIONSWorks with Windows 98, 2000, Me, or XPWhen using Windows 98 and setting up the mouseusing a USB port, you may need your Windows 98installation CD. UNINSTALL INSTRUCTIONS1. Go to “Start” then “Programs” and select “BelkinF8E825-USB mini wireless optical mouse”.2. You should then see the “uninstall” option.Left-click on it.3. Choose your desired language and click “OK”. 4. Then follow the on screen instructions tocomplete the uninstall. Note: You may encounter some “Locked FileDetected” screens during the uninstall. If so left-click on the “Reboot” option for them. It willthen remove those locked files during the nextreboot of your system.FCC/CE StatementDECLARATION OF CONFORMITY WITH FCC RULES FORELECTROMAGNETIC COMPATIBILITYWe, Belkin Corporation, of 501 West Walnut Street, Compton, CA90220, declare under our sole responsibility that the product,F8E825-USB, to which this declaration relates, complies with Part15 of the FCC Rules. Operation is subject to the following twoconditions: (1) this device may not cause harmful interference,and (2) this device must accept any interference received,including interference that may cause undesired operation.Caution: Exposure to Radio Frequency Radiation.The radiated output power of this device is far below the FCCradio frequency exposure limits. Nevertheless, the device shall beused in such manner that the potential for human contact normaloperation is minimized.When connecting an external antenna to the device, the antennashall be placed in such a manner to minimize the potential forhuman contact during normal operation. In order to avoid thepossibility of exceeding the FCC radio frequency exposure limits,human proximity to the antenna shall not be less than 20cm (8inches) during normal operation.Federal Communications Commission NoticeThis equipment has been tested and found to comply with thelimits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonableprotection against harmful interference in a residentialinstallation.This equipment generates, uses, and can radiate radio frequencyenergy. If not installed and used in accordance with theinstructions, it may cause harmful interference to radio ortelevision reception, which can be determined by turning theequipment off and on, the user is encouraged to try and correctthe interference by one or more of the following measures:•Reorient or relocate the receiving antenna.•Increase the distance between the equipment and thereceiver.•Connect the equipment to an outlet on a circuit differentfrom that to which the receiver is connected.•Consult the dealer or an experienced radio/TV technician for help.ModificationsThe FCC requires the user to be notified that any changes ormodifications to this device that are not expressly approved byBelkin Components may void the user’s authority to operate the equipment.Canada-Industry Canada (IC)The wireless radio of this device complies with RSS 139 & RSS210 Industry Canada. This Class B digital complies with CanadianICES-003.Cet appareil numérique de la classe B conforme á la norme NMB-003 du Canada.Europe-European Union NoticeRadio products with the CE alertmarking comply with the R&TTEDirective (1995/5/EC) issued bythe Commission of the EuropeanCommunity. Compliance with this directive implies conformity to thefollowing European Norms (in brackets are the equivalentinternational standards). • EN 60950 (IEC60950) – Product Safety• EN 300 328 Technical requirement for radio equipment.• ETS 300 826 General EMC requirements for radio equipment.To determine the type of transmitter, check the identificationlabel on your Belkin product.Products with the CE marking comply withthe EMC Directive (89/336/EEC) and the LowVoltage Directive (72/23/EEC) issued by theCommission of the European Community.Compliance with these directives impliesconformity to the following European Norms (in brackets are theequivalent international standards).• EN 55022 (CISPR 22) – ElectromagneticInterference• EN 55024 (IEC61000-4-2,3,4,5,6,8,11) –Electromagnetic Immunity• EN 61000-3-2 (IEC610000-3-2) – Power Line Harmonics• EN 61000-3-3 (IEC610000) – Power Line Flicker• EN 60950 (IEC60950) – Product SafetyProducts that contain theradio transmitter are labeled with CE 0682 or CE alert markingand may also carry the CE logo.Belkin Corporation Limited Lifetime Product WarrantyBelkin Corporation warrants this product against defects inmaterials and workmanship for its lifetime. If a defect isdiscovered, Belkin will, at its option, repair or replace theproduct at no charge provided it is returned during the warrantyperiod, with transportation charges prepaid, to the authorizedBelkin dealer from whom you purchased the product. Proof ofpurchase may be required. This warranty does not apply if the product has been damaged byaccident, abuse, misuse, or misapplication; if the product hasbeen modified without the written permission of Belkin; or if anyBelkin serial number has been removed or defaced.THE WARRANTY AND REMEDIES SET FORTH ABOVE AREEXCLUSIVE IN LIEU OF ALL OTHERS, WHETHER ORAL ORWRITTEN, EXPRESSED OR IMPLIED. BELKIN SPECIFICALLYDISCLAIMS ANY AND ALL IMPLIED WARRANTIES, INCLUDING,WITHOUT LIMITATION, WARRANTIES OF MERCHANTABILITY ANDFITNESS FOR A PARTICULAR PURPOSE.No Belkin dealer, agent, or employee is authorized to make anymodification, extension, or addition to this warranty.BELKIN IS NOT RESPONSIBLE FOR SPECIAL, INCIDENTAL, ORCONSEQUENTIAL DAMAGES RESULTING FROM ANY BREACH OFWARRANTY, OR UNDER ANY OTHER LEGAL THEORY, INCLUDINGBUT NOT LIMITED TO LOST PROFITS, DOWNTIME, GOODWILL,DAMAGE TO OR REPROGRAMMING, OR REPRODUCING ANYPROGRAM OR DATA STORED IN OR USED WITH BELKINPRODUCTS.Some states do not allow the exclusion or limitation of incidentalor consequential damages or exclusions of implied warranties, sothe above limitations of exclusions may not apply to you. Thiswarranty gives you specific legal rights, and you may also haveother rights that vary from state to state.Belkin Corporation501 West Walnut StreetCompton • CA • 90220 • USATel: 310.898.1100Fax: 310.898.1111Belkin Components, Ltd.Express Business ParkShipton Way Rushden • NN10 6GLUnited KingdomTel: +44 (0) 1933 35 2000Fax: +44 (0) 1933 31 2000Belkin Components B.V.Starparc Building Boeing Avenue 3331119 PH Schiphol-Rijk The NetherlandsTel: +31 (0) 20 654 7300Fax: +31 (0) 20 654 7349Belkin, Ltd.7 Bowen CrescentWest Gosford • NSW 2250AustraliaTel: +61 (0) 2 4372 8600Fax: +61 (0) 2 4372 8603Tech SupportUS: 310.898.1100 ext. 2263800.223.5546 ext. 2263Europe: 00 800 223 55 460Australia: 1800 666 040© 2003 Belkin Corporation. All rights reserved. All trade names are registeredtrademarks of respectivemanufacturers listed.P74211-Abelkin.comP74211-A_F8E825-USB man.qxd 7/8/03 5:06 PM Page 2

Navigation menu