Belkin F8M010 Low power FM Stereo transmitter User Manual

Belkin International, Inc. Low power FM Stereo transmitter P75185 F8M010 TuneCast 3 mnl indd

a href="https://usermanual.wiki/Belkin" itemprop="url"> Belkin >

User Manual

IntroductionUser ManualTuneCast® 3 Mobile FM Transmitter
Introduction Operating InstructionsOperating InstructionsCongratulations and thank you for purchasing the TuneCast 3 Mobile FM Transmitter from Belkin. This product is designed to play your portable audio device through your car, home, or portable stereo. Please review this User Manual carefully so that you can be sure to get the most from your TuneCast 3, virtually anywhere you go.Introduction | 01 | 02Stereo/MonoUsing the TuneCast 3 Mobile FM Transmitter1. Turn down your car stereo’s volume.2. Tune your stereo frequency to a channel with a weak broadcast signal. The ideal channel is one that is not broadcasting a radio program, or is doing so weakly.3. Connect the TuneCast 3 to your portable audio device. 4. Connect the included Auto Power Cord to your cigarette-lighter outlet in your car and to the bottom of your TuneCast 3 for optional powering in the car. 5. Press and hold the ON/OFF button for approximately two seconds. The display’s status bar will indicate when the device is powered on.6. Press the ” ” or “ ” button on the TuneCast 3 to match the frequency on the radio chosen in step 2. Pressing and holding either button will provide faster tuning.7. Adjust the volume on the audio device to about three-fourths of the maximum. Adjust the volume of your FM radio to the desired listening level.ON/OFFForward/Back3.5mm CablePreset 1Preset 2Memory PresetFrequencyPower SourceBattery or DC PowerStereo/Mono
Operating InstructionsOperating Instructions | 03Storing and Using Presets1. To store a preset, select the desired frequency using ” ” or “ ” buttons. Press and hold the desired preset button (1 or 2) for two seconds (the status bar will give you visible feedback). An audible beep sounds in the transmitted audio when the new frequency is programmed. The TuneCast 3 display reflects the change when the memory button is released by showing which memory button was pressed along with the frequency saved in that memory position.2. To select one of your preset frequencies, momentarily press “1” or “2”. This will instantly tune the TuneCast 3 to the frequency stored in that preset. NOTE: Storing a preset will memorize the frequency as well as the current mono/stereo setting.Memory PresetsStored PresetStereo/Mono SelectionTransmitting music in stereo generally gives you the highest-quality listening experience. However, you may get better FM-signal reception by changing the transmission to mono. The TuneCast 3 transmits in stereo mode by default. We suggest that you switch from stereo to mono transmission only if your car stereo is NOT receiving a clear signal from the TuneCast 3, or if you are listening to mono recordings such as audio books.Press and hold the “Mono/Stereo” button located on the upper-left corner of the TuneCast 3. The status-bar indicator will transition from stereo to mono or vice versa. The TuneCast 3 display will return to normal operation where the current frequency is shown along with the current mono or stereo setting represented by:Mono/Stereo ButtonMono/Stereo DisplayOperating Instructions | 04Operating Instructions
Download:
Mirror Download [FCC.gov]
Document ID734949
Application IDFgIsI6Zf8u4/FAqUoTgfUg==
Document DescriptionUser Manual
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize118.11kB (1476335 bits)
Date Submitted2006-12-05 00:00:00
Date Available2006-12-05 00:00:00
Creation Date2006-10-06 11:44:58
Producing SoftwareAdobe PDF Library 6.0
Document Lastmod2006-11-08 11:24:43
Document TitleP75185_F8M010 TuneCast_3_mnl.indd
Document CreatorAdobe InDesign CS (3.0.1)
FCC ID Filing: K7SF8M010

Navigation menu