Beltronics USA G7M5 Radar Detector User Manual

Beltronics USA Inc Radar Detector

User Manual.pdf

Settings & Programming Press and hold the MRK and SEN buttons to access Programming. To exit Programming, simply wait a few seconds without pressing a button. The unit will display Completed to confirm your selections. Press MRK to go from one category to the next Press VOLUME + or -to change your setting within a category User Mode Advanced· Access and customize all Settings and Programming Novice Access and  customize units and display color,  (all other Settings are set to factory defaults) NOTE Switch to advanced mode to view all settings Pilot Scanning" Scanning Bar with Full Word Full Word Full Word: AutoScan, Auto NoX,  or Highway Display Color  Blue·/Green/Red/Amber  Set color to match  your vehicle's dash display Speed Display On· Displays current speed Off Displays battery voltage Speed Mute Off /20-160 mph Offers double beep alert tones below specified speed 20 mph· Over Speed Off /20-160 mph Reminds you  when  you  exceed a specified speed 70 mph· Signal Strength Meter Standard· Single band with  bar graph of signal strength Tech  Single band with  numeric frequency Threat  Multiple bands with  bar graph  of signal strengths Basic Basic messages replace bands: Caution (if traveling below Speed Mute limit) Slow Down (if traveling above Speed Mute limit) Tones Standard· Standard Beltronics alert tones Mild Mild alert tones AutoMute On·/ Off Automatically reduces audio during alert AutoLock On·/ Off Automatically stores and locks out false alarms Units English·/Metric Units for distance and  speed Voice On·/ Off Voice announcements GPS Filter On"/ Off Enables GPS-powered features AutoPower Off 1 Hour 2 Hours 4 Hours· 8 Hour Power turns on or off depending on your vehicle's ignition type (constant power or switched) Powers off automatically after 1 hour Powers off automatically after 2 hours Powers off automatically after 4 hours Powers off automatically after 8 hours NOTE If AutoPower is on, the display screen goes blank after 30 minutes to save screen life.  Display screen will turn on automatically after you reach 10 MPH Bands Default· Default settings for North America Modified Customize the bands you want to monitor Press SEN to go from one Band category to the next Press VOLUME + or -to change your setting within a category X Band On·/ Off K Band On·/ Off Ka Band On·/ Off Ka-POP On/Off· Laser On·/ Off TSR On"/ Off Automatically rejects traffic flow sensors-monitoring false alarms Markers Default· Default settings Modified Customize the types of locations you  want to be alerted to Press SEN to go from one Marker category to the next Press VOLUME + or -to change your setting within a category Other On"/Off Other location Redlight On·/ Off Red light camera Red &Speed On·/ Off Red light &speed  camera Speed Cam On·/ Off Speed camera Speed Trp On·/ Off Speed trap Air Patrol On/Off· Air patrol
Clear Locations  Marked  Clear all  user Marked  locations. Press SEN button to confirm Lockouts  Clear all lockouts.  Press SEN button to confirm Defender  Clear all  Defender data.  Press SEN button to confirm Format  Clear Defender database, all markers, and all  lockouts. Press SEN button to confirm "Default Setting FCC NOTE: Modifications not expressly approved by the manufacturer c?uld void the user's FCC granted authority to operate the equipment. FCC ID: QL4G7M5. This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received including interference that may cause undesired operation.
Using GT-7 1.  Plug small end of SmartCord into modular jack on GT-7 and large end of SmartCord into your car's lighter/accessory socket. 2.  GT-7 should power on automatically. If not, press the device's power button. Earphone Jack Connects to optional 3.5 mm stereo earphone odular Jack Connects to SmartCord for powering your device ini USB Jack Connects to your computer via USB Almini B cable for downloading software updates Using SmartCord Mute Button: Press to mute an alert; press three times to lock out a false alert; press twice while receiving a  locked-out alert to unlock.  Alert Light:  Blinks orange when receiving an alert.  Power Light:  Lights blue when receiving power.  Modular Connector Plugs into detector jack Lighter Adapter Connects to lighter/acce wry 'ocket

Navigation menu