BiSRO MB-SFA Two-Way Main Controller User Manual UserManual bisro
BiSRO Co.,Ltd. Two-Way Main Controller UserManual bisro
BiSRO >
Users Manual
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 983433 |
| Application ID | /U3Ky6Ps5GRsAmYQ+HqOuw== |
| Document Description | Users Manual |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 132.08kB (1651019 bits) |
| Date Submitted | 2008-08-11 00:00:00 |
| Date Available | 2008-08-11 00:00:00 |
| Creation Date | 2008-08-06 08:58:42 |
| Producing Software | Corel PDF Engine Version 14.0.0.567 |
| Document Lastmod | 0000-00-00 00:00:00 |
| Document Title | UserManual(bisro).cdr |
| Document Creator | CorelDRAW |
| Document Author: | SDE |
www.signca.com ALD-401 / ASF-301 SBC High Tech Center 3F, 932 Wongok-Dong, Danwon-Gu, Ansan-Si, Gyeonggi-Do, Korea +82-31-491-0226 User Manual Before you commence using your system, please read completely. Thank you for purchasing our product. Our systems have all been designed and tested to be compatible with the earliest to latest vehicles available throughout the world. Our primary goal was to provide a reliable and stable product. Our secondary goal was to ensure that our systems are easy to install. Our final goal was to provide features that would benefit the user and installer. We are confident that our products will meet and exceed your expectations. We are constantly working hard in order to research, design, and build next generation products. We would not expect anything less since we use our products in our own vehicles. MIC MIC Mark ▶Remote Control FCC ID: MIC Mark: ▶Antenna Module FCC ID: MIC Mark: Caution!! Read Carefully The user and installer should completely read the User Manual, Installation Manual, and the vehicle’s manual completely before installing and operating this system. Not reading the manuals completely may result in injury or damage to the user(s), installer(s), and/or the vehicle. Installation and use of this system is acknowledgment that the user and installer have fully read the manuals and indemnify Zenesis Alarms from any injuries or damages resulting from wrong use of our system. Please take the following precautions. When using remote start, place the gear in Park(P) 1. (automatic transmission) or Neutral (manual transmission) and set the Emergency Brake (either side hand brake or foot brake). The transmission (Tx) and reception (Rx) distance will 2. vary from interference from other radio signals. If any defects are discovered, do not open or attempt 3. to repair the system. Ask the installer for assistance. Zenesis Alarms will not be responsible for any theft 4. and/or damages to your vehicle. The installer of this system will be responsible for any 5. injuries and/or damages resulting from incorrect installation. The user of this system will be responsible for any 6. injuries and/or damages resulting from misuse. Contents Introduction 1. 2. 3. 4. System Contents Remote Control Button Layout Remote Control Battery Replacement Remote Control Button Introduction 10 11 Introduction Primary Features 1. Lock (Arm) / Unlock (Disarm) 2. Remote Start 3. Trunk Release 4. Status (ALD-401) 5. Panic 6. Siren Mute ON/OFF (ALD-401) 7. Valet Mode ON/OFF 8. Remote Control Beep ON/OFF (ALD-401) 9. Ignition Lock ON/OFF 10. Paging ON/OFF 11. Passive Arm ON/OFF 12. Safety Rearm ON/OFF 13. Cold Start ON/OFF 14. Turbo Timer ON/OFF 15. Temperature Status (ALD-401) 13 13 14 14 14 14 15 15 15 16 16 16 1. 2. 3. 4. 5. 6. 7. 8. User Option Programming Program Remote Control to System Remote Start Reservation Option 1 / Option 2 Input Aux 1 Output Aux 2 Output Shock Sensor Shock Sensor Sensitivity ▶ Warranty Card 18 18 19 19 19 19 20 20 1. System Contents 2. Remote Control Button Layout 3. Remote Control Battery Replacement 10 4. Remote Control Button Introduction 11 Introduction CONTENTS Secondary Features 21 1. System Contents 2. Remote Control Button Layout → Antenna Control Module / “Brain” Remote Control x 2 (1 x 2-way & 1 x 1-way) Antenna Module Lock / Arm Unlock / Disarm LED Trunk Release Remote Start ▶Specifications Wiring Harness 2-way Remote Control Siren 202A / 202AS Radiation ±20ppm/year Temp. -40℃ ~ +80℃ Dimensions 28×12×68.7mm Weight 15g (without battery) Introduction Manuals User / Installation Introduction Shock Sensor 202A / 202AS Stickers 3. Remote Control Battery Replacement ① Use a 3mm Philips screwdriver to remove the screw on the rear panel of the remote control. ② Use a hand to hold the front panel. Use your free hand to gently pull the rear panel off by prying the key holder. 4. Remote Control Button Introduction Item Button(s) Description 0.5 sec Lock (Arm) 0.5 sec Unlock (Disarm) 0.5 sec Status 2 sec Panic 2 sec Remote Start ON/OFF 2 sec Trunk Release 4 sec Siren ON/OFF 10 11 ③ Once the rear panel is removed, you will see the PCB and the battery. Follow the direction of “Remove Battery” to safely remove it. Slide the new battery in the direction of “Insert Battery”. Use a 3V CR2032 battery only. Duration 12 13 0.5 sec Remote Control Addition (Normal) 0.5 sec Remote Control Addition (Door lock after Remote Start) 0.5 sec Aux 2 Output 0.5 sec Aux 1 Output 2 sec User Programmable Options 4 sec Passive Lock (Arm) ON/OFF 4 sec Valet Mode ON/OFF 4 sec Safety Re-lock (Rearm) ON/OFF 4 sec Ignition Lock ON/OFF 4 sec Cold Start Timer ON/OFF 4 sec Turbo Timer ON/OFF 14 15 16 Remove Battery 17 10 Insert Battery ※ Caution : Ensure that the polarity of the battery is correct. The positive (+) terminal should be facing towards you. (0.5 sec ) 1 Remote Control LED Blink (2 sec) 2 Remote Control LED Blinks ( 4 sec) 3 Remote Control LED Blinks Press both buttons at the same time for the specified duration. Introduction 18 Note Introduction 11 1. Door Lock / Arm 1) Door Lock / Arm 0.5 sec ·Successful Door Lock / Arm Vehicle 1 parking light flash & 1 siren chirp Remote Control 1 blink & 1 beep ·Failed Door Lock / Arm from Open Trunk, Hood, and/or Door Vehicle 4 parking light flashes & 4 siren chirps Remote Control 1 blink & 1 beep ·If the Trunk and/or Hood is open while Arming (202A / 202AS), the siren will sound immediately. Main System Features Note ·If the Door is open while arming (202A / 202AS), the siren will sound after 45 seconds. Since the Doors cannot be locked and the system cannot be armed (202A / 202AS) while the Trunk and/or Hood is open, ensure that the Trunk and Hood are closed before Locking / Arming. 2) Door Unlock / Disarm 0.5 sec ·Successful Unlock / Disarm Vehicle 2 parking light flashes & 2 siren chirps Remote Control 1 blinks & 2 beeps 1. Lock (Arm) / Unlock (Disarm) 2. Remote Start 3. Trunk Release 4. Status (ALD-401) 5. Panic 6. Siren Mute ON/OFF (ALD-401) 7. Valet Mode ON/OFF 8. Remote Control Beep ON/OFF (ALD-401) 9. Ignition Lock ON/OFF 10. Paging ON/OFF 11. Passive Arm ON/OFF 12. Safety Rearm ON/OFF 13. Cold Start ON/OFF 14. Turbo Timer ON/OFF 13 13 14 14 14 14 15 15 15 16 16 16 Status Antenna Module LED Armed Mode Normal Flash Disarmed Mode No Flash Triggered Alarm after Arming Fast Flash ※ After the alarm is triggered... ① Button → The siren will stop. 5 siren chirps and fast LED flashes on the Antenna Module will confirm button press. ② Button → The siren will stop. The system will be disarmed with 2 parking light flashes & 2 siren chirps. ③ Door Open and Closed → The LED on the Antenna Module will stop flashing quickly. ④ Button → The system will Arm normally. ·Siren duration can be programmed through the User Programmable Options on page 18. 2. Remote Start 2 sec ·Successful Remote Start 5 parking light flashes & 5 siren chirps Remote Control 1 Vehicle blink & start tone ·Failed Remote Start Vehicle Reason for Failure Remote Control 1 parking light flash & 1 siren chirp XXX 3 parking light flashes & 3 siren chirps XXX Door is open 4 parking light flashes & 4 siren chirps XXX Trunk and/or hood is open 7 parking light flashes & 7 siren chirps XXX Remote start reservation has failed Key is in key cylinder at ON position ·If the button is pressed for 2 seconds while Remote Start is ON, Remote Start will turn OFF. ·After the door(s) is(are) open after Remote Start, the key must be put into the key cylinder within 2 minutes or the engine will turn OFF. ·The default Remote Start engine running time is 5 minutes. The time can be changed through the User Programmable Options on page 18. Do not use the Remote Start feature if the vehicle is in an enclosed area. Do not use the Remote Start Primary Features Primary Features 3) Arm / Disarm Status (202A / 202AS) Caution feature where laws prevent its usage. Do not turn the key to the Start position or else damage may be done to the starter motor. 12 13 3. Trunk Release Vehicle 7. Valet Mode ON/OFF 2 sec 2 parking light flashes & 2 siren chirps Remote Control 1 blink & 1 beep Note 4 sec ·ON 1 parking light flash & 1 siren chirp Vehicle ·Trunk release will unlock the door(s) and disarm (202A / 202AS) the system. Remote Control 1 blink & 1 beep ·OFF On manual transmission vehicles, Trunk Release will turn OFF remote start reservation. 2 parking light flashes & 2 siren chirps Remote Control 2 Vehicle blinks & 2 beeps ·When Valet Mode is ON, the siren will be OFF and no features except for lock and unlock will work. 4. Status (ALD-401) 3 times 0.5 sec Remote Control LED Note Status ▶ Valet Mode via Key (Emergency Shut Off) ① Open driver’s side door. ② Insert the key and turn to the ON position. Within 3 seconds, turn the key between ACC↔ON 3 times and on the third time leave the key in the ON position. 1 parking light flash and 1 siren chirp will confirm the operation. ※ This feature can be used to turn off the alarm with the key if the system has been triggered. ※ Valet Mode can only be turned off via the remote control. Whenever the vehicle is being lent to an individual, turning Valet Mode ON is suggested. 8. Ignition Lock ON/OFF 4 sec ·Ignition Lock ON - The doors will lock after 20 seconds of driving or the foot brake is pressed. Vehicle 1 parking light flash & 1 siren chirp Remote Control 1 blink & 1 beep blinks & 2 beeps ·When the key is turned to the OFF position, the doors will unlock. ·Ignition Lock OFF 2 parking light flashes & 2 siren chirps Remote Control 2 9. Passive Arm ON/OFF Primary Features 5. Panic ·If there is a potential threat, you can alert those around by using this feature. ·The siren will sound for 2 minutes and the parking lights will flash. ·Press either the or the button to turn OFF Panic. 4 sec ·ON Vehicle 6. Siren Mute ON/OFF (ALD-401) ·OFF Vehicle 4 sec Vehicle 1 parking light flash & 1 siren chirp Remote Control 1 blink & 1 beep ·All features of the system still function with siren Mute ON. ·Siren Mute OFF - Siren ON 1 parking light flash & 1 siren chirp 1 parking light flash & 1 siren chirp Remote Control 2 Remote Control 1 2 parking light flashes & 2 siren chirps Remote Control 2 ·Upon Passive Arming, the ·Siren Mute ON - Siren OFF Vehicle 14 ·Once a door is opened and closed and the door is not locked (system armed) via the remote control, the system will automatically lock (system arm) the doors. ·The system will lock (system arm) the doors after 25 seconds of the last door closing. Every 5 seconds, 1 parking light flash and 1 siren chirp will occur. On the 5th occurrence, the doors will lock (system arm). 2 sec button will blink once and 1 beep will sound. Caution If Passive Arm is ON, always carry the remote control. blink & 1 beep blinks & 2 beeps Primary Features Vehicle blinks & 2 beeps 15 10. Safety Rearm ON/OFF 4 sec ·If the doors are unlocked (system disarmed) and a door is not opened, the doors will lock (system rearm) after 30 seconds automatically. ·Safety Rearm ON 1 parking light flash & 1 siren chirp Remote Control 1 + Vehicle blink & 1 beep ·Safety Rearm OFF 2 parking light flashes & 2 siren chirps Remote Control 2 + blinks & 2 beeps Vehicle ·If Safety Rearm occurs, the button will blink once and 1 beep will sound. 11. Cold Start Timer ON/OFF 메뉴구성 4 sec ·A timer can be set to remote start the car. ·Cold Start Timer ON 1 parking light flash & 1 siren chirp Vehicle Remote Control 1 ·Cold Start Timer OFF 2 parking light flashes & 2 siren chirps Remote Control 2 Vehicle blink & 1 beep blinks & 2 beeps ※ The timer can be set through the User Programmable Options on page 18. 12. Turbo Timer ON/OFF 4 sec ·This feature will allow turbocharged or supercharged vehicles to cool down by idling the engine for a specified amount of time. Even though the key is turned to the OFF position, the engine will idle. ·Turbo Timer ON 1 parking light flash & 1 siren chirp Remote Control 1 + Vehicle blink & 1 beep ·Turbo Timer OFF 2 parking light flashes & 2 siren chirps Remote Control 2 + blinks & 2 beeps Vehicle Caution Please ensure that the vehicle is Park (automatic transmission) or Neutral (manual transmission). Also, ensure that the hand brake or foot brake is engaged.. Primary Features 13. Temperature Status (ALD-401) 16 2 sec ·The interior temperature of the vehicle will be displayed as a series of LED’s on the remote control. Temperature Remote Control LED Less than or equal to -10 °C (14 °F) -9 °C (16 °F) to 0 °C (32 °F) 1 °C (34 °F) to 10 °C (50 °F) 11 °C (52 °F) to 20 °C (68 °F) Greater than 20 °C (68 °F) blink & 1 beep blink & 1 beep blink & 1 beep blink & 1 beep blinks & 2 beeps 1. 2. 3. 4. 5. 6. 7. 8. User Option Programming Program Remote Control to System Remote Start Reservation Option 1 / Option 2 Input Aux 1 Output Aux 2 Output Shock Sensor Shock Sensor Sensitivity 18 18 19 19 19 19 20 20 Secondary Features ※ The duration for idling can be specified through the User Programmable Options on page 18. 17 + 3. Remote Start Reservation 2 sec ·Manual transmission vehicles require remote start reservation in order to ensure that the vehicle is properly prepared for remote start. There are 2 remote start reservation modes: automatic and manual. Please note that automatic and manual do not refer to the transmission type. Rather, automatic and manual refer to the type of remote start reservation. Options Feature Button Combination Feature Remote Start Run Time Diesel Warm Up Time Siren Sound Time Turbo Timer Time (2 sec) → → → Option (2 sec) → → → (2 sec) → → → (2 sec) → → Remote Start Reservation (2 sec) → → Cold Start Timer Time (2 sec) → → Default 1) Automatic Remote Start Reservation (Default) Option 5 min 15 min Option 15 sec 10 sec 5 sec Option 30 sec 70 sec 100 sec → Option 2 min 5 min 10 min → Option Automatic Manual → Option 1 hour 2 hours 25 min 2) 수동예약 (사용자 옵션설정) 3 hours → Default Values. ※ The Button Combination includes the initial buttons to get into User Programmable Options. ※ Each button must be pressed within 5 seconds of each other or else User Programmable mode will terminate. 4 times Secondary Features ① Before turning off the engine, put the transmission into Neutral. Ensure that the hand brake or parking brake is engaged. Take your foot off the foot brake. ② Press the button for 2 seconds. ③ Turn the key to the OFF position. The engine should still be running. ④ Exit the vehicle within 2 minutes. ⑤ Once the last door is closed, the engine will turn off. Lock (Arm) the system. Remote start is ready to be used. ※ Remote Start Reservation can be changed through the User Programmable Options on page 18. 2. Program Remote Control to System 18 ① Before turning off the engine, put the transmission into Neutral. Ensure that the hand brake or parking brake engaged. Take your foot off the foot brake. ② Turn the key to the OFF position. The engine should still be running. ③ Exit the vehicle within 2 minutes. ④ Once the last door is closed, the engine will turn off. Lock (Arm) the system. Remote start is ready to be used. ① Close driver’s side door. Insert key and turn to the ON position. ② Turn the key ACC↔ON 4 times within 3 seconds. On the 4t h time, leave the key in the ON position. ③ 3 parking light flashes and 3 siren chirps will confirm remote control programming mode. ④ Press the correct button combination for 0.5 seconds as outlined below. ▶ Typical vehicles ▶ Vehicles that unlock doors after remote start ⑤ After each remote control is added, there will be a confirmation of 2 parking light flashes and 2 siren chirps. You can add up to 3 remote controls per system. ⑥ Once the key is turned to the OFF position or 10 seconds without adding a remote control passes, the system will exit remote control programming mode. ※ Each time a remote control is added, all remote controls must be reprogrammed to the system. Adding a remote control erases previously stored remote controls from the system. 4. Option 1 / Option 2 Input ·Additional sensors can be added to the system using Option 1 and/or Option 2 input(s). ·No additional programming is required. ·When the sensor(s) is(are) triggered, the parking lights will flash and the siren will sound. 5. Aux 1 Output ·Aux 1 Output can be used to control other devices. For example, window modules can be added to roll up or roll down windows. · + (0.5 sec) will activate Aux 1 Output. 2 parking light flashes and 2 siren chirps will confirm output. The remote control will blink 2 times and beep 2 times. 6. Aux 2 Output ·Aux 2 Output can be used to control other devices. For example, window modules can be added to roll up or roll down windows. · + (0.5 sec) will activate Aux 2 Output. 2 parking light flashes and 2 siren chirps will confirm output. The remote control will blink 2 times and beep 2 times. Secondary Features 1. User Programmable Options ·When you enter programming mode by holding + for 2 seconds, the + LED’s will blink 1 time and 1 beep will be heard. Follow the chart below for programming the options. 19 7. Shock Sensor ·The dual stage shock sensor can detect 2 types of shock: light and hard. Light shocks will result in siren chirps and parking light flashes. Hard shocks will result in the system being triggered. Sustained light shocks will also trigger the system. 8. Shock Sensor Sensitivity ·The sensitivity of the shock sensor can be controlled by turning a dial on the shock sensor module. ·Turn the dial according to the amount of sensitivity that is desired. Keep in mind that turning the sensitivity to its maximum can result in false alarms. Test the setting by arming the system and tapping the shock sensor. Warranty Card This warranty card must be completed and mailed to be eligible for warranty coverage. Model Number Owner’s Name Owner’s Address Owner’s Phone Date of Purchase Date of Install Retailer Name Retailer Address Retailer’s Phone Installer Name Installer Address Installer’s Phone The Control Module has a limited lifetime warranty. All other parts have a limited 1 year warranty. For full details, please visit www.zenesisalarms.com. Secondary Features Mail this card to: 20 Zenesis Alarms XXXXXXXXXX
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.6 Linearized : No XMP Toolkit : 3.1-702 Creation Date--Text : Producer : Corel PDF Engine Version 14.0.0.567 Mod Date--Text : Format : application/pdf Creator : SDE Title : UserManual(bisro).cdr Creator Tool : CorelDRAW Modify Date : 2008:08:07 09:22:09+09:00 Metadata Date : 2008:08:07 09:22:09+09:00 Document ID : uuid:77c6ea61-a0b4-4a0c-9d09-7d453778f310 Instance ID : uuid:1ac020c8-7042-4256-a25d-416e5b103618 Has XFA : No Page Count : 11 Create Date : D:20080806085842Z Author : SDEEXIF Metadata provided by EXIF.tools