Bilian Electronic R8188EU1F 150Mbps Wireless N USB Module User Manual

Shenzhen Bilian Electronic Co., Ltd. 150Mbps Wireless N USB Module

User manual

B-LINK ELECTRONIC CO., LTD inshenzhenBL-8188EU1(EUS)Product SpecificationWLAN 11b/g/n USB MODULE Version: 2.6FCC StatementThis device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) Thisdevice may not cause harmful interference, and (2) this device must accept any interference received, includinginterference that may cause undesired operation.Any Changes or modifications not expressly approved by the party responsible for compliance could void the user'sauthority to operate the equipment.Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant topart 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interferencein a residential installation. This equipment generates uses and can radiate radio frequency energy and, if notinstalled and used in accordance with the instructions, may cause harmful interference to radio communications.However, there is no guarantee that interference will not occur in a particular installation. If this equipment doescause harmful interference to radio or television reception, which can be determined by turning the equipment offand on, the user is encouraged to try to correct the interference by one or more of the following measures:-Reorient or relocate the receiving antenna.-Increase the separation between the equipment and receiver.-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.-Consult the dealer or an experienced radio/TV technician for help.The 150Mbps Wireless USBModule is designed to comply with the FCC statement. FCC ID is S8J-R8188EU1F. The host system using 150Mbps Wireless N USB Module, should have label indicated it contain modular’sFCC ID:S8J-R8188EU1F.This radio module must not installed to colocate and operating simultaneously with other radios in host systemadditional testing and equipment authorizationmay be required to operating simultaneously with other radio.RF warning for Mobile device:This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. Thisequipment should be installed and operated with minimum distance 20cm between the radiator & your body.
B-LINK ELECTRONIC CO., LTD inshenzhen1Contents1 General Description............................................................................................................................................22 The range of applying.........................................................................................................................................23 Features................................................................................................................................................................24 DC Characteristics............................................................................................................................................45 The main performance of product....................................................................................................................46 DC/RF characteristics........................................................................................................................................ 57 The block diagram of product principle.......................................................................................................... 68 The supported platform..................................................................................................................................... 69 The definition of product Pin............................................................................................................................ 710 PACKING............................................................................................................................................................811 The 6th Pin connect to antenna, please refer to design demand.................................................................... .912 The 6th Pin connect to antenna, please refer to design demand...................................................................1013 Tpical Solder Reflow Profile............................................................................................................................10
B-LINK ELECTRONIC CO., LTD in21 General DescriptionBL-8188EU1 product Accord with FCC CE and is 150M wireless USB adapter which has lowerpower consumption, high linearity output power, accords with IEEE802.11B/G/N, and supportsIEEE802.11i safety protocol, along with IEEE 802.11e standard service quality. It connects withother wireless device which accorded with these standards together, supports the new data encryptionon 64/128 bit WEP and safety mechanism on WPA-PSK/WPA2-PSK, WPA/WPA2.Its wirelesstransmitting rate rises 150M, equivalent to 10 times of common 11b product. The inner AI high gainceramics antenna adapts different kinds of work environment. It’s easy and convenient to link towireless network for the users using desktop, laptop and other device that needs connect to wirelessnetwork.2 The range of applyingMID, networking camera, STB GPS, E-book, Hard disk player, Network Radios, PSP, etc, the devicewhich need be supported by wireless networking.3 FeaturesFeatureImplementationPower supplyVCC3.3V +-0.2V 220MAClock source40MHzTemperaturerangeWork temperature:-20ºC---70ºCStorage temperature -55°C ~ +125°CPackageSMT 6 pinsWLAN featuresGeneral features■CMOS MAC, Baseband PHY, and RF in a single chip for IEEE802.11b/g/n compatible WLAN■Complete 802.11n solution for 2.4GHz band■72.2Mbps receive PHY rate and 72.2Mbps transmit PHY rate using 20MHzbandwidth■150Mbps receive PHY rate and 150Mbps transmit PHY rate using 40MHzbandwidth
B-LINK ELECTRONIC CO., LTD in3■Compatible with 802.11n specification■Backward compatible with 802.11b/g devices while operating in 802.11nmodeHost InterfaceComplies with USB Specification Revision 2.0StandardsSupported■IEEE 802.11b/g/n compatible WLAN■IEEE 802.11e QoS Enhancement (WMM)■IEEE 802.11h TPC, Spectrum Measurement■802.11i (WPA, WPA2). Open, shared key, and pair-wise keyauthentication servicesWLAN MACFeatures■Frame aggregation for increased MAC efficiency (A-MSDU, A-MPDU)■Low latency immediate High-Throughput Block Acknowledgement(HT-BA)■PHY-level spoofing to enhance legacy compatibility■Power saving mechanism■Channel management and co-existence■Transmit Opportunity (TXOP) Short Inter-Frame Space (SIFS) bursting forhigher multimedia bandwidthWLAN PHYFeatures■IEEE 802.11n OFDM■One Transmit and one Receive path (1T1R)■20MHz and 40MHz bandwidth transmission■Short Guard Interval (400ns)■DSSS with DBPSK and DQPSK, CCK modulation with long and shortpreamble■OFDM with BPSK, QPSK, 16QAM, and 64QAM modulation.Convolutional Coding Rate: 1/2, 2/3, 3/4, and 5/6■Maximum data rate 54Mbps in 802.11g and 150Mbps in 802.11n■Switch diversity for DSSS/CCK■Hardware antenna diversity■Selectable receiver FIR filters■Programmable scaling in transmitter and receiver to trade quantizationnoise against increased probability of clipping Fast■receiver Automatic Gain Control (AGC)■On-chip ADC and DAC
B-LINK ELECTRONIC CO., LTD in44 DC CharacteristicsSymbolParameterMinimumTypicalMaximumUnitsVD33A,VD33D3.3V I/OSupply Voltage3.03.33.6vVD12A,VD12D1.2V CoreSupply Voltage1.101.21.32vVD15A,VD15D1.5V SupplyVoltage1.4251.51.575vIDD333.3V RatingCurrent--600mA5 The main performance of productItemDescriptionThe supported protocol andstandardIEEE 802.11n, IEEE 802.11g,EE 802.11bInterface typeUSB2.0The range of frequency2.412-2.462GHZThe amount of workingChannel1-11(America, Canada);1-13(China, Europe);1-14(Japan)Data ModulationOFDM/DBPSK/DQPSK/CCKWorking ModeInfrastructure, Ad-HocThe transmitting rate135/54/48/36/24/18/12/9/6 /1M(self-adapting)Spread spectrumDSSSSensitivity @PER54/135M:-74dBm@10%PER,11M:-85dBm@8%PER6M: -88dBm@10%PER ,1M: -90dBm@8%PERRF Power135M:15dBM,54M:15dBM,11M:19dBMThroughput80Mbps(external 2dbi antenna ,damping 50dbm in Shielding box )The connect type ofAntennaConnect to the external antenna through the half hole, Connect to
B-LINK ELECTRONIC CO., LTD in5the external antenna through the half hole, The antennaand other interface get connected to the external devicesby the edge half a circle welding plateLED indicatorstatus indicatorThe transmit distanceIndoor 100M, Outdoor 300M, according the local environmentWorking Power consumption68MAMENS(L*W*H)12.3MM*12.9MM*0.6MMThe chipset modelRTL8188EUS6 DC/RF characteristicsTermsContentsSpecification : IEEE802.11bModeDSSS / CCKFrequency2412 – 2462MHzData rate1, 2, 5.5, 11MbpsDC CharacteristicsminTyp.max.unitTX mode257263271mARx mode808284mAStandby mode140145146uASpecification : IEEE802.11gModeOFDMFrequency2412 - 2462MHzData rate6, 9, 12, 18, 24, 36, 48, 54MbpsDC CharacteristicsminTyp.max.unitTX mode244245245mARx mode888989mAStandby mode143145146uASpecification : IEEE802.11nModeOFDMFrequency2412 - 2462MHzData rate6.5, 13, 19.5, 26, 39, 52, 58.5, 65MbpsDC CharacteristicsminTyp.max.unitTX mode201207214mA
B-LINK ELECTRONIC CO., LTD in6Rx mode909394mAStandby mode144145146uA7 The block diagram of product principle8 The supported platformOperating SystemCPU FrameworkDriverWIN2000/XP/VISTA/WIN7X86 PlatformEnableLINUX2.4/2.6ARM, MIPSIIEnableWINCE5.0/6.0ARM ,MIPSIIEnable
B-LINK ELECTRONIC CO., LTD in79 The definition of product PinTop and bottom view of BL-8188-EU1Pin No:TYPEDescription1PDC :3.3V2I/OUDM-3I/OUDP+4PGND5PGND6OANT123465
B-LINK ELECTRONIC CO., LTD in810 The Structure and Size of productBL-R8188-EU111:Packing
B-LINK ELECTRONIC CO., LTD in912:The 6th Pin connect to antenna, please refer to design demandConnect to the 6th pin of ModuleConnect to the 5th pin of Modulea) The current of 3.3V power supply must be >300mA, its ripple wave must be <30mV. The GNDpins of module and external antenna need to be an incorporated part. The ground plane should belarger, module and antenna should keep far away from interference source.b) The sixth pin is 2.4G high frequency output, coplanar impedance of layout line between this pinto antenna interface should be 50Ω, we suggest use arc line or straight line, and beside the linethere will be ground plane that its length as shout as possible, the longest length is no more than50mm.c) L1, C1, C2 constitute a π-type network that we preset, please make it close to antenna interface,this π-type network is used to match the antenna parameters and control the radiation. It shouldbe adjusted according to the real condition when being used. Normally you can only mount L1that its parameters are: 10pF, NP0 material. No need C1 and C2
B-LINK ELECTRONIC CO., LTD in1013:Tpical Solder Reflow Profile

Navigation menu