Bilian Electronic R8188EU1F 150Mbps Wireless N USB Module User Manual
Shenzhen Bilian Electronic Co., Ltd. 150Mbps Wireless N USB Module
User manual
B-LINK ELECTRONIC CO., LTD in shenzhen BL-8188EU1(EUS) Product Specification WLAN 11b/g/n USB MODULE Version: 2.6 FCC Statement This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -Reorient or relocate the receiving antenna. -Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help. The 150Mbps Wireless USB Module is designed to comply with the FCC statement. FCC ID is S8J-R8188EU1F. The host system using 15 0Mbps Wireless N USB Module, should have label indicated it contain modular’s FCC ID:S8J-R8188EU1F. This radio module must not installed to colocate and operating simultaneously with other radios in host system additional testing and equipment authorization may be required to operating simultaneously with other radio. RF warning for Mobile device: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. shenzhen B-LINK ELECTRONIC CO., LTD in Contents General Description............................................................................................................................................2 The range of applying.........................................................................................................................................2 Features................................................................................................................................................................2 DC Characteristics............................................................................................................................................4 The main performance of product....................................................................................................................4 DC/RF characteristics........................................................................................................................................ 5 The block diagram of product principle.......................................................................................................... 6 The supported platform..................................................................................................................................... 6 The definition of product Pin............................................................................................................................ 7 10 PACKING............................................................................................................................................................8 11 The 6th Pin connect to antenna, please refer to design demand.................................................................... .9 12 The 6th Pin connect to antenna, please refer to design demand...................................................................10 13 Tpical Solder Reflow Profile............................................................................................................................10 B-LINK ELECTRONIC CO., LTD in 1 General Description BL-8188EU1 product Accord with FCC CE and is 150M wireless USB adapter which has lower power consumption, high linearity output power, accords with IEEE802.11B/G/N, and supports IEEE802.11i safety protocol, along with IEEE 802.11e standard service quality. It connects with other wireless device which accorded with these standards together, supports the new data encryption on 64/128 bit WEP and safety mechanism on WPA-PSK/WPA2-PSK, WPA/WPA2.Its wireless transmitting rate rises 150M, equivalent to 10 times of common 11b product. The inner AI high gain ceramics antenna adapts different kinds of work environment. It’s easy and convenient to link to wireless network for the users using desktop, laptop and other device that needs connect to wireless network. 2 The range of applying MID, networking camera, STB GPS, E-book, Hard disk player, Network Radios, PSP, etc, the device which need be supported by wireless networking. 3 Features Feature Power supply Implementation Clock source 40MHz Temperature range Work temperature:-20ºC---70ºC Package SMT 6 pins VCC3.3V +-0.2V 220MA Storage temperature -55°C ~ +125°C WLAN features General features ■CMOS MAC, Baseband PHY, and RF in a single chip for IEEE 802.11b/g/n compatible WLAN ■Complete 802.11n solution for 2.4GHz band ■72.2Mbps receive PHY rate and 72.2Mbps transmit PHY rate using 20MHz bandwidth ■150Mbps receive PHY rate and 150Mbps transmit PHY rate using 40MHz bandwidth B-LINK ELECTRONIC CO., LTD in ■Compatible with 802.11n specification ■Backward compatible with 802.11b/g devices while operating in 802.11n Host Interface Standards Supported mode Complies with USB Specification Revision 2.0 ■IEEE 802.11b/g/n compatible WLAN ■IEEE 802.11e QoS Enhancement (WMM) ■IEEE 802.11h TPC, Spectrum Measurement ■802.11i (WPA, WPA2). Open, shared key, and pair-wise key authentication services WLAN MAC Features ■Frame aggregation for increased MAC efficiency (A-MSDU, A-MPDU) ■Low latency immediate High-Throughput Block Acknowledgement (HT-BA) ■PHY-level spoofing to enhance legacy compatibility ■Power saving mechanism ■Channel management and co-existence ■Transmit Opportunity (TXOP) Short Inter-Frame Space (SIFS) bursting for higher multimedia bandwidth ■IEEE 802.11n OFDM ■One Transmit and one Receive path (1T1R) ■20MHz and 40MHz bandwidth transmission ■Short Guard Interval (400ns) ■DSSS with DBPSK and DQPSK, CCK modulation with long and short preamble WLAN PHY Features ■OFDM with BPSK, QPSK, 16QAM, and 64QAM modulation. Convolutional Coding Rate: 1/2, 2/3, 3/4, and 5/6 ■Maximum data rate 54Mbps in 802.11g and 150Mbps in 802.11n ■Switch diversity for DSSS/CCK ■Hardware antenna diversity ■Selectable receiver FIR filters ■Programmable scaling in transmitter and receiver to trade quantization noise against increased probability of clipping Fast ■receiver Automatic Gain Control (AGC) ■On-chip ADC and DAC B-LINK ELECTRONIC CO., LTD in 4 DC Characteristics Symbol VD33A, VD33D VD12A, VD12D VD15A, VD15D IDD33 Parameter 3.3V I/O Supply Voltage 1.2V Core Supply Voltage 1.5V Supply Voltage 3.3V Rating Current Minimum 3.0 Typical 3.3 Maximum 3.6 Units 1.10 1.2 1.32 1.425 1.5 1.575 600 mA 5 The main performance of product Item Description The supported protocol and IEEE 802.11n, IEEE 802.11g,EE 802.11b standard Interface type USB2.0 The range of frequency 2.412-2.462GHZ The amount of working 1-11(America, Canada);1-13(China, Europe);1-14(Japan) Channel Data Modulation OFDM/DBPSK/DQPSK/CCK Infrastructure, Ad-Hoc Working Mode 135/54/48/36/24/18/12/9/6 /1M(self-adapting) The transmitting rate DSSS Spread spectrum 54/135M:-74dBm@10%PER, 11M:-85dBm@8%PER Sensitivity @PER 6M: -88dBm@10%PER , 1M: -90dBm@8%PER 135M:15dBM, RF Power 54M:15dBM, 11M:19dBM 80Mbps(external 2dbi antenna ,damping 50dbm in Shielding box ) Throughput The connect type of Antenna Connect to the external antenna through the half hole, Connect to B-LINK ELECTRONIC CO., LTD in the external antenna through the half hole, The antenna and other interface get connected to the external devices by the edge half a circle welding plate LED indicator The transmit distance Working Power consumption MENS(L*W*H) The chipset model status indicator Indoor 100M, Outdoor 300M, according the local environment 68MA 12.3MM*12.9MM*0.6MM RTL8188EUS 6 DC/RF characteristics Terms Contents Specification : IEEE802.11b Mode DSSS / CCK Frequency 2412 – 2462MHz Data rate 1, 2, 5.5, 11Mbps DC Characteristics min Typ. max. unit TX mode 257 263 271 mA Rx mode 80 82 84 mA Standby mode 140 145 146 uA Specification : IEEE802.11g Mode OFDM Frequency 2412 - 2462MHz Data rate 6, 9, 12, 18, 24, 36, 48, 54Mbps DC Characteristics min Typ. max. unit TX mode 244 245 245 mA Rx mode 88 89 89 mA Standby mode 143 145 146 uA Specification : IEEE802.11n Mode OFDM Frequency 2412 - 2462MHz Data rate 6.5, 13, 19.5, 26, 39, 52, 58.5, 65Mbps DC Characteristics min Typ. max. unit TX mode 201 207 214 mA B-LINK ELECTRONIC CO., LTD in Rx mode 90 93 94 mA Standby mode 144 145 146 uA 7 The block diagram of product principle 8 The supported platform Operating System CPU Framework Driver WIN2000/XP/VISTA/WIN7 X86 Platform Enable LINUX2.4/2.6 ARM, MIPSII Enable WINCE5.0/6.0 ARM ,MIPSII Enable B-LINK ELECTRONIC CO., LTD in 9 The definition of product Pin Top and bottom view of BL-8188-EU1 Pin No: TYPE Description DC :3.3V I/O UDM- I/O UDP+ GND GND ANT B-LINK ELECTRONIC CO., LTD in 10 The Structure and Size of product BL-R8188-EU1 11:Packing B-LINK ELECTRONIC CO., LTD in 12:The 6th Pin connect to antenna, please refer to design demand Connect to the 6th pin of Module Connect to the 5th pin of Module a) The current of 3.3V power supply must be >300mA, its ripple wave must be <30mV. The GND pins of module and external antenna need to be an incorporated part. The ground plane should be larger, module and antenna should keep far away from interference source. b) The sixth pin is 2.4G high frequency output, coplanar impedance of layout line between this pin to antenna interface should be 50Ω, we suggest use arc line or straight line, and beside the line there will be ground plane that its length as shout as possible, the longest length is no more than 50mm. c) L1, C1, C2 constitute a π-type network that we preset, please make it close to antenna interface, this π-type network is used to match the antenna parameters and control the radiation. It should be adjusted according to the real condition when being used. Normally you can only mount L1 that its parameters are: 10pF, NP0 material. No need C1 and C2 B-LINK ELECTRONIC CO., LTD in 13:Tpical Solder Reflow Profile 10
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.7 Linearized : No XMP Toolkit : 3.1-701 Create Date : 2016:01:04 16:47:47Z Creator Tool : WPS Office Modify Date : 2016:01:06 13:13:54+08:00 Metadata Date : 2016:01:06 13:13:54+08:00 Format : application/pdf Creator : xjghost Title : Document ID : uuid:8296a22d-1292-427d-8b1f-4624088fad7f Instance ID : uuid:d99748e5-7d03-400d-9911-f1ec68836348 Page Count : 11 Author : xjghostEXIF Metadata provided by EXIF.tools