Bilian Electronic WR2000 300Mbps Wireless N Router User Manual
Shenzhen Bilian Electronic Co., Ltd. 300Mbps Wireless N Router Users Manual
Users Manual
Quick Installation Guide Model:BL-WR2000 300Mbps Wireless N Router 1.Connecting the device Note: Please use wired network connections only to configure the Router. 1 Connect the WAN port on your Router to the Modem's LAN port with an Ethernet cable. (If there is no Modem, please use the incoming cable directly into the router's WAN port). Internet Cable/DSL Modem Wireless N Router 2 Connect your computer to the Port labeled 1~4 on the Router with an Ethernet cable. Internet Cable/DSL Modem PC Wireless N Router 3 Plug the provided power adapter into the power jack on the back of the router and the other end to a standard electrical wall socket. Power outlet Internet Cable/DSL Modem PC Wireless N Router 4 Check the router's LED indicator lights display status is the same as described. Power: Solid light SYS : Flashing WPS: Flashing WLAN: Flashing LAN:Flashing or solid light if the corresponding port is connected WAN:Flashing or solid light Note: If the LED indicator light display abnormal, please check whether the connection is correct. 2.Configuring the device Note: First of all, please configure your computer's IP address to automatically obtain, if not clear, please refer to FAQ3. 1 Login Open your web browser,input 192.168.16.1 in the address field and press Enter. about:blank - Microsoft Internet Explorer Address 192.168.16.1 Go A dialog box will prompt you for the User name and Password. Enter the default values and click OK. User name:admin Password: admin Click OK The web management page will display after a successful login Quick Setup Status Network Wireless Password Time Zone Firewall Export/import Virtual Server Restore System information Click Quick Setup Run time 00:30:01 System time 07:32:24 Software version v2.0.10. QOS Firmware 2 Internet Paremeters Configuration This page will then display Quick Setup Network Wireless Firewall Virtual Server QOS Quick Setup Qucik Setup DHCP (Auto Config) Select a connection type Static Mode (fixed IP) PPPOE (ADSL) Back Next Cancel Apply Click Next How to select a connection type? Note: 1.Make sure the cable is securely plugged into the WAN port before detection. 2.If the connection type your ISP provided is PPTP,L2TP,you must go to “Network-WAN” to configure your connection type manually. The Internet parameters provided by ISP when users apply for Internet access Connection type No parameters, don't use any router and don't do any setting Dynamic A static IP address, subnet mask, gateway and DNS server Static IP address Static Mode User name and password PPPoE A Configuration for Dynamic When you choose the Dynamic IP no change required. Click “Next” to go on the next setting. B Configuration for Static Mode This page will then display Quick Setup Network Wireless Firewall Virtual Server QOS Quick Setup Qucik Setup Enter the IP address,subnet Mask, Gateway,DNS provided by your ISP Manually. IP address Subnet Mask Gateway Primary DNS Server Secondary DNS Server Back Next (Optional) Cancel Apply Click Next C Configuration for PPPOE This page will then display Quick Setup Network Wireless Firewall Virtual Server Quick Setup Qucik Setup Enter the Access Account and Password provided by your ISP. Access Account Password Back Click Next Next Cancel Apply QOS 3 Wireless Settings Configuration This page will then display Quick Setup Create a unique and easy-to-remember name for your wireless network.You can also keep default settings without the device being affected. Network Wireless Firewall Virtual Server QOS Quick Setup Qucik Setup Network name(SSID) B-LINK_90E09F Security WPA2-PSK AES WPA Algorithms Select Security and WPA Algorithms, Suggest to choose “AES”. TKIP&AES Key Back Next Cancel Apply Set up a wireless Key,the length is more than 8 characters. Click Apply Note: The basic setting for your Router is completed. You will be able to access to the Internet, if not, please refer to the troubleshooting 3.Troubleshooting FAQ1: What should I do if I forget the user name and password? (How to restore the router 's configuration to its factory default settings.) Answer: If you forget the user name and password, the only way to solve this problem is to reset the router. Press and hold the RESET button on the rear panel for 5 to 8 seconds before releasing it. Hold for 5 to 8 seconds FAQ2: What can I do if I cannot access the Internet? 1.Check to see if all the connectors are connected well, including the telephone line (for your modem), Ethernet cables and power adapter. 2.Disconnect the Router and directly connect your computer to the Modem and try to access the Internet. If you still cannot access to the Internet, please contact your ISP or the Modem's manufacturer; otherwise, please reconnect the physical connection between your Modem, Router and the computer, then continue to follow the next step. 3.Make sure that you are connected to the Router with the computer that was originally connected to your modem, then login to the web-based management page and browse to "Network > MAC Clone", click "Clone MAC" and then click "Apply". Reboot the Router and try to access the Internet from your computer, if the problem still, please go to the next step. MAC Address Clone MAC Address: 44:33:4C:90:E0:98 Clone MAC Restore Cancel FAQ3: How to configure the IP address of the computer? For Windows XP OS Go to Start > Control Panel, you will then see the following page. Click Network and Internet Connections Apply For Windows XP OS Click Network Connections Right-click Local Area Connection Click Properties Double-click Internet Protocol (TCP/IP) For Windows XP OS Select Obtain an IP address automatically Select Obtain DNS server address automatically Click OK Click OK For Windows 7 OS Go to Start > Control Panel, you will then see the following page. Click View network status and tasks Click Change adapter settings Right-click Local Area Connection Click Properties For Windows 7 OS Double-click Internet Protocol Version 4 (TCP/IPv4) Click OK Select Obtain an IP address automatically Select Obtain DNS server address automatically Click OK 10 For Windows 7 OS Click OK 11 For Windows 8 OS Press the Keyboard WIN( )+X to popup the menu on the Win8 Desktop, then select Control Panel Click View network status and tasks Click Change adapter settings 12 For Windows 8 OS Right-click Ethernet Click Properties Double-Click Internet Protocol Version4(TCP/Ipv4) 13 For Windows 8 OS Select Obtain an IP address automatically Select Obtain DNS server address automatically Click OK Click OK 14 is the registered trademark of Shenzhen BILIAN Electronic CO . ,Ltd.All the products and product names mentioned herein are the trademarks or registered trademarks of their respective holders 2012 All Rights Reserved. http://www.lefen.com Ver 2.0
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.6 Linearized : Yes XMP Toolkit : 3.1-701 Modify Date : 2015:01:07 11:07:14+08:00 Create Date : 2015:01:07 11:07:14+08:00 Metadata Date : 2015:01:07 11:07:14+08:00 Creator Tool : CorelDRAW X5 Format : application/pdf Title : BL-WR2000快速安装指南英文V2 Creator : blink Document ID : uuid:1f9881b7-3cbf-4ccc-b8e6-f5acd7ad931b Instance ID : uuid:45c5309d-8496-4399-8e04-89e24c2d1d23 Producer : Corel PDF Engine Version 15.1.0.588 Page Count : 17 Author : blinkEXIF Metadata provided by EXIF.tools