Biostar A57A Owners Manual AA55E A1S_120406
2014-07-31
: Biostar Biostar-A57A-Owners-Manual biostar-a57a-owners-manual biostar pdf
Open the PDF directly: View PDF .
Page Count: 51
Download | |
Open PDF In Browser | View PDF |
A57A Setup Manual FCC Information and Copyright This equipment has been tested and found to comply with the limits of a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. There is no guarantee that interference will not occur in a particular installation. The vendor makes no representations or warranties with respect to the contents here and specially disclaims any implied warranties of merchantability or fitness for any purpose. Further the vendor reserves the right to revise this publication and to make changes to the contents here without obligation to notify any party beforehand. Duplication of this publication, in part or in whole, is not allowed without first obtaining the vendor’s approval in writing. The content of this user’s manual is subject to be changed without notice and we will not be responsible for any mistakes found in this user’s manual. All the brand and product names are trademarks of their respective companies. Dichiarazione di conformità sintetica Ai sensi dell’art. 2 comma 3 del D.M. 275 del 30/10/2002 Si dichiara che questo prodotto è conforme alle normative vigenti e soddisfa i requisiti essenziali richiesti dalle direttive 2004/108/CE, 2006/95/CE e 1999/05/CE quando ad esso applicabili Short Declaration of conformity We declare this product is complying with the laws in force and meeting all the essential requirements as specified by the directives 2004/108/CE, 2006/95/CE and 1999/05/CE whenever these laws may be applied Table of Contents Chapter 1: Introduction ................................................................ 1 1.1 Before You Start ....................................................................................1 1.2 Package Checklist .................................................................................1 1.3 Motherboard Features...........................................................................2 1.4 Rear Panel Connectors ..........................................................................3 1.5 Motherboard Layout .............................................................................4 Chapter 2: Hardware Installation .................................................. 5 2.1 Installing Central Processing Unit (CPU)...............................................5 2.2 FAN Headers .........................................................................................7 2.3 Installing System Memory......................................................................8 2.4 Connectors and Slots............................................................................10 Chapter 3: Headers & Jumpers Setup........................................... 13 3.1 How to Setup Jumpers .........................................................................13 3.2 Detail Settings......................................................................................13 Chapter 4: RAID Functions.......................................................... 17 4.1 Operating System................................................................................17 4.2 Raid Arrays..........................................................................................17 4.3 How RAID Works.................................................................................17 Chapter 5: Useful Help................................................................ 20 5.1 Driver Installation Note.......................................................................20 5.2 Software...............................................................................................21 5.3 Extra Information................................................................................23 5.4 AMI BIOS Beep Code............................................................................24 5.5 Troubleshooting...................................................................................25 Chapter 6: bios update ............................................................... 26 6.1 BIOS Update Utility .............................................................................26 6.2 Online Update Utility ..........................................................................28 6.3 BIOSTAR BIOS Flasher .........................................................................30 Appendix: SPEC In Other Languages............................................ 32 German ....................................................................................................................32 French.......................................................................................................................34 Italian.......................................................................................................................36 Spanish .....................................................................................................................38 Portuguese ...............................................................................................................40 Polish........................................................................................................................42 Russian .....................................................................................................................44 Arabic.......................................................................................................................46 Japanese...................................................................................................................48 A57A CHAPTER 1: INTRODUCTION 1.1 BEFORE YOU START Thank you for choosing our product. Before you start installing the motherboard, please make sure you follow the instructions below: 1.2 Prepare a dry and stable working environment with sufficient lighting. Always disconnect the computer from power outlet before operation. Before you take the motherboard out from anti-static bag, ground yourself properly by touching any safely grounded appliance, or use grounded wrist strap to remove the static charge. Avoid touching the components on motherboard or the rear side of the board unless necessary. Hold the board on the edge, do not try to bend or flex the board. Do not leave any unfastened small parts inside the case after installation. Loose parts will cause short circuits which may damage the equipment. Keep the computer from dangerous area, such as heat source, humid air and water. The operating temperatures of the computer should be 0 to 45 degrees Celsius. PACKAGE CHECKLIST Serial ATA Cable X2 Rear I/O Panel for ATX Case X1 User’s Manual X1 Fully Setup Driver DVD X1 Note: The package contents may be different due to area or your motherboard version. 1 Motherboard Manual 1.3 MOTHERBOARD FEATURES SPEC Socket FM1 AMD 64 Architecture enables 32 and 64 bit AMD A-Series / E2-Series processors computing CPU Chipset AMD A55 ITE 8728 Environment Control initiatives Provides the most commonly used legacy H/W Monitor Super I/O functionality Fan Speed Controller Low Pin Count Interface ITE's "Smart Guardian" function Super I/O DDR3 DIMM Slots x 2 Dual Channel Mode DDR3 memory module Main Max Memory Capacity 16GB Memory Each DIMM supports 512MB/ Supports DDR3 800/1066/1333/1600/1866 Registered DIMM and ECC DIMM is not supported 1GB/2GB/4GB/8GB DDR3 Data transfer rates up to 3 Gb/s. SATA II Integrated Serial ATA Controller SATA Version 2.0 specification compliant. RAID 0,1,10 support 10 / 100 Mb/s / 1Gb/s auto negotiation LAN RTL8111E / RTL8111F Half / Full duplex capability 5.1channels audio out Sound VT1708B/ ALC662 Supports HD Audio PCI Express Gen2 x16 Slot x1 Supports PCI-E Gen2 x16, x4 expansion cards PCI Express Gen2 x1 Slot x2 Supports PCI-E Gen2 x1 expansion cards PCI Slot x3 Supports PCI expansion cards SATA Connector x6 Each connector supports 1 SATA device Connectors Front Panel Connector x1 Supports front panel facilities Front Audio Connector x1 Supports front panel audio function S/PDIF out Connector x1 Supports digital audio out function CPU Fan Header x1 CPU Fan power supply (with Smart Fan function) System Fan Header x1 System Fan Power supply CMOS clear Header x1 Restore CMOS data to factory default Slots On Board 2 A57A SPEC USB2.0 Connector x2 Each connector supports 2 front panel USB2.0 ports Printer Port Connector x1 Each connector supports 1 Printer port Power Connector (24-Pin) x1 Connects to Power supply Power Connector (4-Pin) x1 Connects to Power supply PS/2 Keyboard x1 Connects to PS/2 Keyboard PS/2 Mouse x1 Connects to PS/2 Mouse Back Panel Serial Port x1 Connects to RS-232 Port I/O LAN port x1 Connect to RJ-45 ethernet cable USB2.0 Port x6 Connect to USB2.0 devices Audio Jack x3 Provide Audio-In/Out and Mic. connection Board Size 200 mm (W) x 295 mm (L) ATX Biostar reserves the right to add or remove support OS Support Windows XP / Vista / 7 for any OS With or without notice. 1.4 REAR PANEL CONNECTORS P S /2 Mou se L AN L ine In / S urrou nd L ine O ut M ic In 1/ B as s/ Ce nte r P S /2 K e yb oa rd C OM1 US B 2 .0 X 2 US B 2 .0 X 2 U S B 2 .0X 2 3 Motherboard Manual 1.5 MOTHERBOARD LAYOUT KBMS1 CPU_FAN1 COM1 USB1 USB2 DDR3_B1 DDR3_A1 ATXPWR2 ATXPWR1 RJ45USB1 BAT1 AUDIO1 PEX1_1 PEX16_1 LAN PEX1_2 AMD A55 PCI1 Super I/O BIOS PCI2 JCMOS1 JSPDIFOUT1 F_USB1 J_PRINT1 PANEL1 F_USB2 F_AUDIO1 Note: ■ represents the 1st pin. 4 SATA2 SATA1 SATA4 SATA3 SATA6 SATA5 SYS_FAN1 PCI3 Codec A57A CHAPTER 2: HARDWARE INSTALLATION 2.1 INSTALLING CENTRAL PROCESSING UNIT (CPU) Step 1: Pull the lever toward direction A from the socket and then raise the lever up to a 90-degree angle. Step 2: Look for the white triangle on socket, and the gold triangle on CPU should point towards this white triangle. The CPU will fit only in the correct orientation. 5 Motherboard Manual Step 3: Hold the CPU down firmly, and then close the lever toward direct B to complete the installation. Step 4: Put the CPU Fan on the CPU and buckle it. Connect the CPU FAN power cable to the CPU_FAN1. This completes the installation. 6 A57A 2.2 FAN HEADERS These fan headers support cooling-fans built in the computer. The fan cable and connector may be different according to the fan manufacturer. Connect the fan cable to the connector while matching the black wire to pin#1. CPU_FAN1: CPU Fan Header 1 4 Pin 1 2 3 4 Assignment Ground +12V FAN RPM rate sense Smart Fan Control (By Fan) SYS_FAN1: System Fan Header Pin 1 2 3 Assignment Ground +12V FAN RPM rate sense 3 1 Note: CPU_FAN1, SYS_FAN1 support 4-pin and 3-pin head connectors. When connecting with wires onto connectors, please note that the red wire is the positive and should be connected to pin#2, and the black wire is Ground and should be connected to GND. 7 Motherboard Manual 2.3 INSTALLING SYSTEM MEMORY 8 DDR 3_B1 DDR 3_A1 A. DDR3 Modules 1. Unlock a DIMM slot by pressing the retaining clips outward. Align a DIMM on the slot such that the notch on the DIMM matches the break on the Slot. 2. Insert the DIMM vertically and firmly into the slot until the retaining chip snap back in place and the DIMM is properly seated. A57A B. Memory Capacity DIMM Socket Location DDR3 Module DDR3_A1 512MB/1GB/2GB/4GB/8GB DDR3_B1 512MB/1GB/2GB/4GB/8GB Total Memory Size Max is 16GB. C. Dual Channel Memory installation Please refer to the following requirements to activate Dual Channel function: Install memory module of the same density in pairs, shown in the table Dual Channel Status DDR3_A1 DDR3_B1 Disabled X O Disabled O X Enabled O O (O means memory installed, X means memory not installed.) The DRAM bus width of the memory module must be the same (x8 or x16) D. DDR Speed Support Please refer to the following table for DDR speed reference: # of DIMM per Channel # of Ranks per DIMM Max DDR Speed Grade for 1.50V DIMM 1 of 1 UDIMM xR DDR3-1866 1 of 2 UDIMMs xR DDR3-1600 / DDR3-1333 Note: xR: Single or double side memory moudule 9 Motherboard Manual 2.4 CONNECTORS AND SLOTS SATA1~SATA6: Serial ATA Connectors The motherboard has a PCI to SATA Controller with 6 channels SATA interface, it satisfies the SATA 2.0 spec and with transfer rate of 3.0Gb/s. S A TA 2 S A TA 4 S A T A 6 S A TA 1 S A TA3 SA TA5 1 4 Pin 1 2 3 4 5 6 7 Assignment Ground TX+ TXGround RXRX+ Ground 7 ATXPWR2: ATX Power Source Connector This connector provides +12V to CPU power circuit. 10 1 4 2 3 Pin 1 2 3 4 Assignment +12V +12V Ground Ground A57A ATXPWR1: ATX Power Source Connector This connector allows user to connect 24-pin power connector on the ATX power supply. Pin 13 14 15 16 17 18 19 20 21 22 23 24 Assignment +3.3V -12V Ground PS_ON Ground Ground Ground NC +5V +5V +5V Ground 12 24 1 13 Pin 1 2 3 4 5 6 7 8 9 10 11 12 Assignment +3.3V +3.3V Ground +5V Ground +5V Ground PW_OK Standby Voltage+5V +12V +12V +3.3V Note: Before you power on the system, please make sure that both ATXPWR1 and ATXPWR2 connectors have been plugged-in. PCI1/PCI2/PCI3: Peripheral Component Interconnect Slots This motherboard is equipped with 3 standard PCI slots. PCI stands for Peripheral Component Interconnect, and it is a bus standard for expansion cards. This PCI slot is designated as 32 bits. PCI1 PCI2 PCI3 11 Motherboard Manual PEX16_1: PCI-Express Gen2 x16 Slot - PCI-Express 2.0 compliant. Maximum theoretical realized bandwidth of 8GB/s simultaneously per direction, for an aggregate of 16GB/s totally. PCI-Express Gen2 supports a raw bit-rate of 5.0Gb/s on the data pins. 2X bandwidth over the PCI-Express 1.1 architecture. PEX1_1/PEX1_2: PCI-Express Gen2 x1 Slots - PCI-Express 2.0 compliant. Data transfer bandwidth up to 500MB/s per direction; 1GB/s in total. PCI-Express supports a raw bit-rate of 2.5Gb/s on the data pins. PEX 1_1 PEX16_1 PEX 1_2 12 A57A CHAPTER 3: HEADERS & JUMPERS SETUP 3.1 HOW TO SETUP JUMPERS The illustration shows how to set up jumpers. When the jumper cap is placed on pins, the jumper is “close”, if not, that means the jumper is “open”. Pin opened 3.2 Pin closed Pin1-2 closed DETAIL SETTINGS PANEL1: Front Panel Header This 16-pin connector includes Power-on, Reset, HDD LED, Power LED, and speaker connection. It allows user to connect the PC case’s front panel switch functions. PWR_LED On/Off + + - 9 1 16 8 + - RST SPK HLED Pin 1 2 3 4 5 6 7 8 Assignment +5V N/A N/A Speaker HDD LED (+) HDD LED (-) Ground Reset control Function Speaker Connector Hard drive LED Reset button Pin 9 10 11 12 13 14 15 16 Assignment N/A N/A N/A Power LED (+) Power LED (+) Power LED (-) Power button Ground Function N/A N/A Power LED Power-on button 13 Motherboard Manual JCMOS1: Clear CMOS Header Placing the jumper on pin2-3 allows user to restore the BIOS safe setting and the CMOS data. Please carefully follow the procedures to avoid damaging the motherboard. 1 3 Pin 1-2 Close: Normal Operation (default). 1 3 1 3 Pin 2-3 Close: Clear CMOS data. ※ Clear CMOS Procedures: 1. 2. 3. 4. 5. 6. Remove AC power line. Set the jumper to “Pin 2-3 close”. Wait for five seconds. Set the jumper to “Pin 1-2 close”. Power on the AC. Load Optimal Defaults and save settings in CMOS. F_USB1/F_USB2: Headers for USB 2.0 Ports at Front Panel These headers allow user to connect additional USB cable on the PC front panel, and also can be connected with internal USB devices, like USB card reader. F_US B1 F_US B2 14 2 10 1 9 Pin 1 2 3 4 5 6 7 8 9 10 Assignment +5V (fused) +5V (fused) USBUSBUSB+ USB+ Ground Ground Key NC A57A F_AUDIO1: Front Panel Audio Header This header allows user to connect the front audio output cable with the PC front panel. This header supports HD and AC’97 audio front panel connector. 2 10 1 9 Pin 1 2 3 4 5 6 7 8 9 10 HD Audio Assignment Mic Left in Ground Mic Right in GPIO Right line in Jack Sense Front Sense Key Left line in Jack Sense Pin 1 2 3 4 5 6 7 8 9 10 AC’97 Assignment Mic In Ground Mic Power Audio Power RT Line Out RT Line Out Reserved Key LFT Line Out LFT Line Out Note: It is recommended that you connect a high-definition front panel audio module to this connector to avail of the motherboard's high definition audio capability. JSPDIFOUT1: Digital Audio-out Connector This connector allows user to connect the PCI bracket SPDIF output header. Pin 1 2 3 1 Assignment +5V SPDIF_OUT Ground 3 15 Motherboard Manual J_PRINT1: Printer Port Connector This header allows you to connector printer on the PC. 2 26 1 16 Pin 1 2 3 4 5 6 7 8 9 10 11 12 13 Assignment 25 -Strobe -ALF Data 0 Pin 14 15 16 Assignment Ground Data 6 Ground -Error Data 1 -Init Data 2 -Scltin Data 3 Ground Data 4 Ground Data 5 17 18 19 20 21 22 23 24 25 26 Data 7 Ground -ACK Ground Busy Ground PE Ground SCLT Key A57A CHAPTER 4: RAID FUNCTIONS 4.1 OPERATING SYSTEM Supports Windows Vista and Windows 7. 4.2 RAID ARRAYS RAID supports the following types of RAID arrays: RAID 0: RAID 0 defines a disk striping scheme that improves disk read and write times for many applications. RAID 1: RAID 1 defines techniques for mirroring data. RAID 10: RAID 10 combines the techniques used in RAID 0 and RAID 1. 4.3 HOW RAID WORKS RAID 0: The controller “stripes” data across multiple drives in a RAID 0 array system. It breaks up a large file into smaller blocks and performs disk reads and writes across multiple drives in parallel. The size of each block is determined by the stripe size parameter, which you set during the creation of the RAID set based on the system environment. This technique reduces overall disk access time and offers high bandwidth. Features and Benefits Drives: Minimum 2, and maximum is up to 6 or 8. Depending on the platform. Uses: Intended for non-critical data requiring high data throughput, or any environment that does not require fault tolerance. Benefits: provides increased data throughput, especially for large files. No capacity loss penalty for parity. Drawbacks: Does not deliver any fault tolerance. If any drive in the array fails, all data is lost. Fault Tolerance: No. Block 1 Block 3 Block 5 Block 2 Block 4 Block 6 17 Motherboard Manual RAID 1: Every read and write is actually carried out in parallel across 2 disk drives in a RAID 1 array system. The mirrored (backup) copy of the data can reside on the same disk or on a second redundant drive in the array. RAID 1 provides a hot-standby copy of data if the active volume or drive is corrupted or becomes unavailable because of a hardware failure. RAID techniques can be applied for high-availability solutions, or as a form of automatic backup that eliminates tedious manual backups to more expensive and less reliable media. Features and Benefits Drives: Minimum 2, and maximum is 2. Uses: RAID 1 is ideal for small databases or any other application that requires fault tolerance and minimal capacity. Benefits: Provides 100% data redundancy. Should one drive fail, the controller switches to the other drive. Drawbacks: Requires 2 drives for the storage space of one drive. Performance is impaired during drive rebuilds. Fault Tolerance: Yes. Block 1 Block 2 Block 3 18 Block 1 Block 2 Block 3 A57A RAID 10: RAID 1 drives can be stripped using RAID 0 techniques. Resulting in a RAID 10 solution for improved resiliency, performance and rebuild performance. Features and Benefits Drives: Minimum 4, and maximum is 6 or 8, depending on the platform. Benefits: Optimizes for both fault tolerance and performance, allowing for automatic redundancy. May be simultaneously used with other RAID levels in an array, and allows for spare disks. Drawbacks: Requires twice the available disk space for data redundancy, the same as RAID level 1. Fault Tolerance: Yes. Block 1 Block 3 Block 5 Block 1 Block 3 Block 5 Block 2 Block 4 Block 6 Block 2 Block 4 Block 6 19 Motherboard Manual CHAPTER 5: USEFUL HELP 5.1 DRIVER INSTALLATION NOTE After you installed your operating system, please insert the Fully Setup Driver CD into your optical drive and install the driver for better system performance. You will see the following window after you insert the CD The setup guide will auto detect your motherboard and operating system. Note: If this window didn’t show up after you insert the Driver CD, please use file browser to locate and execute the file SETUP.EXE under your optical drive. A. Driver Installation To install the driver, please click on the Driver icon. The setup guide will list the compatible driver for your motherboard and operating system. Click on each device driver to launch the installation program. B. Software Installation To install the software, please click on the Software icon. The setup guide will list the software available for your system, click on each software title to launch the installation program. C. Manual Aside from the paperback manual, we also provide manual in the Driver CD. Click on the Manual icon to browse for available manual. Note: You will need Acrobat Reader to open the manual file. Please download the latest version of Acrobat Reader software from http://www.adobe.com/products/acrobat/readstep2.html 20 A57A 5.2 SOFTWARE Installing Software 1. Insert the Setup CD to the optical drive. The drivers installation program would appear if the Autorun function has been enabled. 2. Select Software Installation, and then click on the respective software title. 3. Follow the on-screen instructions to complete the installation. Launching Software After the installation process, you will see the software icon “eHOT Line” / “BIOS Update” appears on the desktop. Double-click the icon to launch the utility. eHot-Line (Optional) eHot-Line is a convenient utility that helps you to contact with our Tech-Support system. This utility will collect the system information which is useful for analyzing the problem you may have encountered, and then send these information to our tech-support department to help you fix the problem. Before you use this utility, please set Outlook Express as your default e-mail client application program. represents important *informa ti on that you must provide. Wi thout this information, you may not be able to send out the mail. This bl ock will show the i nformation which would be collected in the mail . conditi on *Describe of your system. your area or *Select the area cl ose to you. Provide the e-ma il address that you would like to send the copy to. e the name of *Provid the memory module manufacturer. Provide the name of the power suppl y manufacturer and the model no. Send the mail out. Exi t thi s dialog. Save these in forma tion to a .txt file 21 Motherboard Manual After filling up this information, click “Send” to send the mail out. A warning dialog would appear asking for your confirmation; click “Send” to confirm or “Do Not Send” to cancel. If you want to save this information to a .txt file, click “Save As…” and then you will see a saving dialog appears asking you to enter file name. Enter the file name and then click “Save”. Your system information will be saved to a .txt file. Open the saved .txt file, you will see your system information including motherboard/BIOS/CPU/video/ device/OS information. This information is also concluded in the sent mail. We will not share customer’s data with any other third parties, so please feel free to provide your system information while using eHot-Line service. If you are not using Outlook Express as your default e-mail client application, you may need to save the system information to a .txt file and send the file to our tech support with other e-mail application. Go to the following web http://www.biostar.com.tw/app/en/about/contact.php for getting our contact information. 22 A57A BIOS Update Utility BIOS Update Utility is a convenient utility which allows you to update your motherboard BIOS under Windows system. Please refer to the detailed instructions in the section 6.1 BIOS Update Utility of Chapter 6. 5.3 EXTRA INFORMATION CPU Overheated If the system shutdown automatically after power on system for seconds, that means the CPU protection function has been activated. When the CPU is over heated, the motherboard will shutdown automatically to avoid a damage of the CPU, and the system may not power on again. In this case, please double check: 1. The CPU cooler surface is placed evenly with the CPU surface. 2. CPU fan is rotated normally. 3. CPU fan speed is fulfilling with the CPU speed. After confirmed, please follow steps below to relief the CPU protection function. 1. Remove the power cord from power supply for seconds. 2. Wait for seconds. 3. Plug in the power cord and boot up the system. Or you can: 1. Clear the CMOS data. (See “Close CMOS Header: JCMOS1” section) 2. Wait for seconds. 3. Power on the system again. 23 Motherboard Manual 5.4 AMI BIOS BEEP CODE Boot Block Beep Codes Number of Beeps 1 2 3 4 5 7 10 11 12 13 Description No media present. (Insert diskette in floppy drive A:) “AMIBOOT.ROM” file not found in root directory of diskette in A: Insert next diskette if multiple diskettes are used for recovery Flash Programming successful File read error No Flash EPROM detected Flash Erase error Flash Program error “AMIBOOT.ROM” file size error BIOS ROM image mismatch (file layout does not match image present in flash device) POST BIOS Beep Codes Number of Beeps 1 3 6 7 8 Description Memory refresh timer error Base memory read/write test error Keyboard controller BAT command failed General exception error (processor exception interrupt error) Display memory error (system video adapter) Troubleshooting POST BIOS Beep Codes Number of Beeps 1, 3 6, 7 Troubleshooting Action Reseat the memory, or replace with known good modules. Fatal error indicating a serious problem with the system. Consult your system manufacturer. Before declaring the motherboard beyond all hope, eliminate the possibility of interference by a malfunctioning add-in card. Remove all expansion cards except the video adapter. z If beep codes are generated when all other expansion cards are absent, consult your system manufacturer’s technical support. z If beep codes are not generated when all other expansion cards are absent, one of the add-in cards is causing the malfunction. Insert the cards back into the system one at a time until the problem happens again. This will reveal the malfunctioning card. If the system video adapter is an add-in card, replace or reseat the video adapter. If the video adapter is an integrated part of the system board, the board may be faulty. 24 A57A 5.5 TROUBLESHOOTING Probable 1. 2. Solution There is no power in the system. 1. Power LED does not shine; the fan of the power supply does not 2. work 3. Indicator light on keyboard does not shine. System is inoperative. Keyboard lights are on, power indicator lights are lit, and hard drives are running. System does not boot from a hard disk drive, but can be booted from optical drive. Make sure power cable is securely plugged in. Replace cable. Contact technical support. Using even pressure on both ends of the DIMM, press down firmly until the module snaps into place. 1. Check cable running from disk to disk controller board. Make sure both ends are securely plugged in; check the drive type in the standard CMOS setup. 2. Backing up the hard drive is extremely important. All hard disks are capable of breaking down at any time. System only boots from an optical 1. Back up data and applications drive. Hard disks can be read, files. applications can be used, but system 2. Reformat the hard drive. fails to boot from a hard disk. Re-install applications and data using backup disks. Screen message shows “Invalid Review system’s equipment. Make sure Configuration” or “CMOS Failure.” correct information is in setup. System cannot boot after user installs a 1. Set master/slave jumpers second hard drive. correctly. 2. Run SETUP program and select correct drive types. Call the drive manufacturers for compatibility with other drives. 25 Motherboard Manual CHAPTER 6: BIOS UPDATE There are three ways to update the BIOS: BIOS Update Utility, BIOS Online Update Utility and BIOSTAR BIOS Flasher. Note: The programing procedure may take minutes, please do not make any operation during the programing process. 6.1 BIOS UPDATE UTILITY 1. Installing BIOS Update Utility from the CD Driver. 2. Download the proper BIOS from www.biostar.com.tw . 3. Open BIOS Update Utility and click the Update BIOS button on the main screen. 4. A warning message will show up to request your agreement to start the BIOS update. Click Yes to start the update procedure. 5. Choose the location for your BIOS file in the system. Please select the proper BIOS file, and then click on Open. It will take several minutes, please be patient. 26 A57A 6. After the BIOS Update process is finished, click on OK to reboot the system. 7. While the system boots up and the full screen logo shows up, please press thekey to enter BIOS setup. After entering the BIOS setup, please go to the Save & Exit, using the Restore Defaults function to load Optimized Defaults, and select Save Changes and Reset to restart the computer. Then, the BIOS Update is completed. All the information and content above about the software are subject to be changed without notice. For better performance, the software is being continuously updated. The information and pictures described above are for your reference only. The actual information and settings on board may be slightly different from this manual. Click the Backup BIOS button on the main screen for the backup of BIOS, and select a proper location for your backup BIOS file in the system, and click Save. 27 Motherboard Manual 6.2 ONLINE UPDATE UTILITY 1. Installing BIOS Update Utility from the CD Driver. 2. Please make sure the system is connected to the internet before using this function. 3. Open BIOS Update Utility and click the Online Update button on the main screen. 4. An open dialog will show up to request your agreement to start the BIOS update. Click Yes to start the online update procedure. 5. If there is a new BIOS version, the utility will ask you to download it. Click Yes to proceed. 6. After the download is completed, you will be asked to program (update) the BIOS or not. Click Yes to proceed. 28 A57A 7. After the updating process is finished, you will be asked you to reboot the system. Click OK to reboot. 8. While the system boots up and the full screen logo shows up, press key to enter BIOS setup. After entering the BIOS setup, please go to the Save & Exit, using the Restore Defaults function to load Optimized Defaults, and select Save Changes and Reset to restart the computer. Then, the BIOS Update is completed. All the information and content above about the T-Series software are subject to be changed without notice. For better performance, the software is being continuously updated. The information and pictures described above are for your reference only. The actual information and settings on board may be slightly different from this manual. 29 Motherboard Manual 6.3 BIOSTAR BIOS FLASHER BIOSTAR BIOS Flasher is a BIOS flashing utility providing you an easy and simple way to update your BIOS via USB pen drive. The BIOSTAR BIOS Flasher is built in the BIOS ROM. To enter the utility, press during the Power-On Self Tests (POST) procedure while booting up. Updating BIOS with BIOSTAR BIOS Flasher 1. Go to the website to download the latest BIOS file for the motherboard. 2. Then, copy and save the BIOS file into a USB flash (pen) drive. 3. Insert the USB pen drive that contains the BIOS file to the USB port. 4. Power on or reset the computer and then press during the POST process. 5. After entering the POST screen, the BIOS-FLASHER utility pops out. Choose [fs0] to search for the BIOS file. 30 A57A 6. Select the proper BIOS file, and a message asking if you are sure to flash the BIOS file. Click Yes to start updating BIOS. 7. A dialog pops out after BIOS flash is completed, asking you to restart the system. Press the [Y] key to restart system. 8. While the system boots up and the full screen logo shows up, press key to enter BIOS setup. After entering the BIOS setup, please go to the Save & Exit, using the Restore Defaults function to load Optimized Defaults, and select Save Changes and Reset to restart the computer. Then, the BIOS Update is completed. z z This utility only allows storage device with FAT32/16 format and single partition. Shutting down or resetting the system while updating the BIOS will lead to system boot failure. 31 Motherboard Manual APPENDIX: SPEC IN OTHER LANGUAGES GERMAN Spezifikationen CPU Chipsatz Sockel FM1 Die AMD 64-Architektur unterstützt eine 32-Bit- und AMD A-Series / E2-Series Prozessoren 64-Bit-Datenverarbeitung AMD A55 ITE 8728 Super E/A Umgebungskontrolle, Bietet die häufig verwendeten alten Super Hardware-Überwachung E/A-Funktionen. Lüfterdrehzahl-Controller Low Pin Count-Schnittstelle "Smart Guardian"-Funktion von ITE Dual-Kanal DDR3 Speichermodul DDR3 DIMM-Steckplätze x 2 Unterstützt DDR3 800/1066/1333/1600/1866 Arbeitsspeich Max. 16GB Arbeitsspeicher er Unterstützt DDR3 2000 (OC) Jeder DIMM unterstützt 512MB/ registrierte DIMMs. ECC DIMMs werden nicht 1GB/2GB/4GB/8GB DDR3. unterstützt. Datentransferrate bis zu 3 Gb/s SATA II Integrierter Serial ATA-Controller Konform mit der SATA-Spezifikation Version 2.0 Unterstützt RAID 0,1,10 LAN 10 / 100 / 1000 Mb/s Auto-Negotiation RTL8111E / RTL8111F Halb-/ Vollduplex-Funktion 5.1-Kanal-Audioausgabe Audio-Codec VT1708B/ ALC662 Steckplätze PCI Express Gen2 x16 Steckplatz x1 PCI Express Gen2 x1 Steckplatz x2 PCI Steckplatz x3 Onboard-Ans SATA-Anschluss chluss 32 Unterstützt High-Definition Audio x6 Jeder Anschluss unterstützt 1 SATA-Laufwerk Fronttafelanschluss x1 Unterstützt die Fronttafelfunktionen Front-Audioanschluss x1 Unterstützt die Fronttafel-Audioanschlussfunktion S/PDIF Ausgangsanschluss x1 Unterstützt die digitale Audioausgabefunktion CPU-Lüfter-Sockel x1 CPU-Lüfterstromversorgungsanschluss (mit Smart Fan-Funktion) A57A Spezifikationen System-Lüfter-Sockel x1 "CMOS löschen"-Sockel x1 USB2.0-Anschluss x2 System-Lüfter-Stromversorgungsanschluss Jeder Anschluss unterstützt 2 Fronttafel-USB2.0-Anschlüsse Druckeranschluss Anschluss x1 Stromanschluss (24-polig) x1 Stromanschluss (4-polig) x1 PS/2-Tastatur x1 PS/2-Maus x1 Rückseiten-E Serieller Anschluss /A Jeder Anschluss unterstützt 1 Druckeranschluss x1 LAN-Anschluss x1 USB2.0-Anschluss x6 Audioanschluss x3 Platinengröße 200 mm (B) X 295 mm (L) Biostar behält sich das Recht vor, ohne Ankündigung OS-Unterstüt zung Windows XP / Vista / 7 die Unterstützung für ein Betriebssystem hinzuzufügen oder zu entfernen. 33 Motherboard Manual FRENCH SPEC UC Socket FM1 Processeurs AMD A-Series / E2-Series Chipset Super E/S L'architecture AMD 64 permet le calcul 32 et 64 bits AMD A55 ITE 8728 Initiatives de contrôle environnementales, Fournit la fonctionnalité de Super E/S Moniteur de matériel patrimoniales la plus utilisée. Contrôleur de vitesse de ventilateur Interface à faible compte de broches Fonction "Gardien intelligent" de l'ITE Module de mémoire DDR3 à mode à double voie Fentes DDR3 DIMM x 2 Mémoire Capacité mémoire maximale de 16Go principale Chaque DIMM prend en charge des DDR3 de 512Mo/1Go/2Go/4Go/8Go Prend en charge la DDR3 800/1066/1333/1600/1866 Prend en charge la DDR3 2000 (OC) Les DIMM à registres et DIMM avec code correcteurs d'erreurs ne sont pas prises en charge Taux de transfert jusqu'à 3 Go/s. SATA II Conforme à la spécification SATA Version 2.0 Contrôleur Serial ATA intégré Prise en charge RAID 0,1,10 LAN 10 / 100 / 1000 Mb/s négociation automatique RTL8111E / RTL8111F Half / Full duplex capability Sortie audio à 5.1 voies Codec audio VT1708B/ ALC662 Fentes Connecteur embarqué 34 Prise en charge de l'audio haute définition Fente PCI Express Gen2 x16 x1 Fente PCI Express Gen2 x1 x2 Fente PCI x3 Connecteur SATA x6 Connecteur du panneau avant x1 Prend en charge les équipements du panneau avant Connecteur Audio du panneau avant x1 Prend en charge la fonction audio du panneau avant Connecteur de sortie S/PDIF x1 Prend en charge la fonction de sortie audio numérique Embase de ventilateur UC x1 Embase de ventilateur système x1 Chaque connecteur prend en charge 1 périphérique SATA Alimentation électrique du ventilateur UC (avec fonction de ventilateur intelligent) Alimentation électrique du ventilateur système A57A SPEC Embase d'effacement CMOS x1 Connecteur USB2.0 x2 Chaque connecteur prend en charge 2 ports USB2.0 de panneau avant Connecteur de Port d'imprimante x1 Connecteur d'alimentation x1 Chaque connector prend en charge 1 Port d'imprimante (24 broches) Connecteur d'alimentation x1 (4broches) E/S du panneau arrière Dimensions de la carte Clavier PS/2 x1 Souris PS/2 x1 Port série x1 Port LAN x1 Port USB2.0 x6 Fiche audio x3 200 mm (l) X 295 mm (H) Support SE Windows XP / Vista / 7 Biostar se réserve le droit d'ajouter ou de supprimer le support de SE avec ou sans préavis. 35 Motherboard Manual ITALIAN SPECIFICA CPU Chipset Socket FM1 L’architettura AMD 64 abilita la co mputazione 32 Processori AMD A-Series / E2-Series e 64 bit AMD A55 ITE 8728 Super I/O Funzioni di controllo dell’ambiente: Fornisce le funzionalità legacy Super Monitoraggio hardware I/O usate più comunemente. Controller velocità ventolina Interfaccia LPC (Low Pin Count) Funzione "Smart Guardian" di ITE Alloggi DIMM DDR3 x 2 Modulo di memoria DDR3 a canale doppio Memoria Capacità massima della memoria 16GB Supporto di DDR3 800/1066/1333/1600/1866 principale Ciascun DIMM supporta DDR3 Supporto di DDR3 2000 (OC) 512MB/1GB/2GB/4GB/8GB DIMM registrati e DIMM ECC non sono supportati Velocità di trasferimento dei dati fino a 3 Gb/s. SATA II Controller Serial ATA integrato Compatibile specifiche SATA Versione 2.0 Supporto RAID 0,1,10 LAN Negoziazione automatica 10 / 100 / 1000 Mb/s RTL8111E / RTL8111F Capacità Half / Full Duplex Codec audio Uscita audio 5.1 canali VT1708B/ ALC662 Supporto audio High-Definit ion (HD) Alloggio PCI Express Gen2 x16 x1 Alloggi Alloggio PCI Express Gen2 x1 x2 Alloggio PCI x3 Connettori Connettore SATA su scheda x6 Ciascun connettore supporta 1 unità SATA Connettore pannello frontale x1 Supporta i servizi del pannello frontale Connettore audio frontale x1 Supporta la funzione audio pannello frontale Connettore output S/PDIF x1 Supporta la funzione d’output audio digitale Collettore ventolina CPU x1 Alimentazione ventolina CPU (con funzione Smart Fan) Collettore ventolina sistema 36 x1 Alimentazione ventolina di sistema A57A SPECIFICA Collettore cancellaz ione CMOS x1 Connettore USB2.0 x2 Ciascun connettore supporta 2 porte USB2.0 pannello frontale Connettore Porta stampante x1 Connettore alimentazione x1 Ciascun connettore supporta 1 Porta stampante (24 pin) Connettore alimentazione x1 (4pin) I/O Tastiera PS/2 x1 Mouse PS/2 x1 Porta seriale x1 Porta LAN x1 Porta USB2.0 x6 Connettore audio x3 pannello posteriore Dimension 200 mm (larghezza) x 295 mm i scheda (altezza) Biostar si riserva il diritto di aggiungere o Sistemi operativi supportati Windows XP / Vista / 7 rimuovere il supporto di qualsiasi sistema operativo senza preavviso. 37 Motherboard Manual SPANISH Especificación CPU Conjunto de chips Conector FM1 La arquitectura AMD 64 permite el procesado de 32 y Procesadores AMD A-Series / E2-Series 64 bits AMD A55 ITE 8728 Súper E/S Iniciativas de control de entorno, Le ofrece las funcionalidades heredadas de Monitor hardware uso más común Súper E/S. Controlador de velocidad de ventilador Interfaz de cuenta Low Pin Función "Guardia inteligente" de ITE Módulo de memoria DDR3 de canal Doble Ranuras DIMM DDR3 x 2 Admite DDR3 de 800/1066/1333/1600/1866 Memoria Capacidad máxima de memoria de 16GB principal Cada DIMM admite DDR de Admite DDR3 de 2000 (OC) No admite DIMM registrados o DIMM compatibles con 512MB/1GB/2GB/4GB/8GB ECC Tasas de transferencia de hasta 3 Gb/s. SATA II Controlador ATA Serie Integrado Compatible con la versión SATA 2.0 Admite RAID 0,1,10 Red Local Negociación de 10 / 100 / 1000 Mb/s RTL8111E / RTL8111F Funciones Half / Full dúplex Códecs de sonido Ranuras Salida de sonido de 5.1 canales VT1708B/ ALC662 Soporte de sonido de Alta Definición Ranura PCI Express Gen2 x16 X1 Ranura PCI express Gen2 x1 X2 Ranura PCI X3 Conectores Conector SATA en placa 38 X6 Cada conector soporta 1 dispositivos SATA Conector de panel frontal X1 Soporta instalaciones en el panel frontal Conector de sonido frontal X1 Soporta funciones de sonido en el panel frontal Conector de salida S/PDIF X1 Soporta función de salida de sonido digital A57A Especificación Cabecera de ventilador de CPU X1 Fuente de alimentación de ventilador de CPU (con función Smart Fan) Cabecera de ventilador de sistema X1 Fuente de alimentación de ventilador de sistema Cabecera de borrado de CMOS X1 Conector USB2.0 X2 Cada conector soporta 2 puertos USB2.0 frontales Conector Puerto de impresora X1 Cada conector soporta 1 Puerto de impresora Conector de alimentación X1 (24 patillas) Conector de alimentación X1 (4patillas) Panel trasero de E/S Tamaño de la placa Teclado PS/2 X1 Ratón PS/2 X1 Puerto serie X1 Puerto de red local X1 Puerto USB2.0 X6 Conector de sonido X3 200 mm. (A) X 295 mm. (H) Soporte de sistema operativo Biostar se reserva el derecho de añadir o retirar el Windows XP / Vista / 7 soporte de cualquier SO con o sin aviso previo. 39 Motherboard Manual PORTUGUESE ESPECIFICAÇÕES CPU Chipset Socket FM1 A arquitectura AMD 64 permite uma computação de 32 Processadores AMD A-Series / E2-Series e 64 bits AMD A55 ITE 8728 Especificaçã o Super I/O Iniciativas para controlo do ambiente Proporciona as funcionalidades mais utilizadas em termos da especificação Super I/O. principal Controlador da velocidade da ventoinha Função "Smart Guardian" da ITE Interface LPC (Low Pin Count). Memória Monitorização do hardware Ranhuras DIMM DDR3 x 2 Módulo de memória DDR3 de canal duplo Capacidade máxima de memória: 16GB Suporta módulos DDR3 800/1066/1333/1600/1866 Cada módulo DIMM suporta uma Suporta módulos DDR3 2000 (OC) memória DDR3 de 512MB/ Os módulos DIMM registados e os DIMM ECC não são 1GB/2GB/4GB/8GB suportados Velocidades de transmissão de dados até 3 Gb/s. SATA II Controlador Serial ATA integrado Compatibilidade com a especificação SATA versão 2.0 Suporta as funções RAID 0,1,10 LAN Codec de som Ranhuras 40 Capacidade semi/full-duplex Saída de áudio de 5.1 canais VT1708B/ ALC662 Suporta a especificação High-Definition Audio Ranhura PCI Express Gen2 x16 x1 Ranhura PCI Express Gen2 x1 x2 Ranhura PCI x3 Conectores Conector SATA na placa Auto negociação de 10 / 100 / 1000 Mb/s RTL8111E / RTL8111F x6 Cada conector suporta 1 dispositivo SATA Conector do painel frontal x1 Para suporte de várias funções no painel frontal Conector de áudio frontal x1 Suporta a função de áudio no painel frontal Conector de saída S/PDIF x1 Suporta a saída de áudio digital Conector da ventoinha da CPU x1 Conector da ventoinha do sistema x1 Alimentação da ventoinha da CPU (com a função Smart Fan) Alimentação da ventoinha do sistema A57A ESPECIFICAÇÕES Conector para limpeza do CMOS x1 Conector USB2.0 x2 Cada conector suporta 2 portas USB2.0 no painel frontal Conector da para impressora x1 Conector de alimentação x1 Cada conector suporta 1 Porta para impressora (24 pinos) Conector de alimentação x1 (4 pinos) Entradas/S aídas no painel Teclado PS/2 x1 Rato PS/2 x1 Porta série x1 Porta LAN x1 Porta USB2.0 x6 Tomada de áudio x3 traseiro Tamanho da placa 200 mm (L) X 295 mm (A) A Biostar reserva-se o direito de adicionar ou remover Sistemas operativos suportados Windows XP / Vista / 7 suporte para qualquer sistema operativo com ou sem aviso prévio. 41 Motherboard Manual POLISH SPEC Procesor Chipset Socket FM1 Architektura AMD 64 umożliwia przetwarzanie 32 i 64 AMD A-Series / E2-Series Procesory bitowe AMD A55 Gniazda DDR3 DIMM x 2 Moduł pamięci DDR3 z trybem podwójnego kanału Pamięć Maks. wielkość pamięci 16GB Obsługa DDR3 800/1066/1333/1600/1866 główna Każde gniazdo DIMM obsługuje moduły Obsługa DDR3 2000 (OC) 512MB/1GB/2GB/4GB/8GB DDR3 Brak obsługi Registered DIMM oraz ECC DIMM ITE 8728 Funkcje kontroli warunków pracy, Super I/O Zapewnia najbardziej powszechne funkcje Monitor H/W Super I/O. Kontroler prędkości wentylatora Interfejs Low Pin Count Funkcja ITE "Smart Guardian" Transfer danych do 3 Gb/s. SATA II Zintegrowany kontroler Serial ATA Zgodność ze specyfikacją SATA w wersji 2.0 Obsługa RAID 0,1,10 10 / 100 / 1000 Mb/s z automatyczną negocjacją LAN RTL8111E / RTL8111F szybkości Działanie w trybie połowicznego/pełnego dupleksu Kodek dźwiękowy Gniazda Złącza wbudowane 5.1 kanałowe wyjście audio VT1708B/ ALC662 Obsługa High-Definition Audio Gniazdo PCI Express Gen2 x16 x1 Gniazdo PCI Express Gen2 x1 x2 Gniazdo PCI x3 Złącze SATA x6 Każde złącze obsługuje 1 urządzenie SATA Złącze panela przedniego x1 Obsługa elementów panela przedniego Przednie złącze audio x1 Obsługa funkcji audio na panelu przednim Złącze wyjścia S/PDIF x1 Obsługa funkcji cyfrowego wyjścia audio Złącze główkowe wentylatora procesora x1 Złącze główkowe wentylatora systemowego 42 x1 Zasilanie wentylatora procesora (z funkcją Smart Fan) Zasilanie wentylatora systemowego A57A SPEC Złącze główkowe kasowania CMOS x1 Złącze USB2.0 x2 Każde złącze obsługuje 2 porty USB2.0 na panelu przednim Złącze Port drukarki x1 Złącze zasilania (24 pinowe) x1 Złącze zasilania (4 pinowe) x1 Klawiatura PS/2 x1 Mysz PS/2 x1 Back Panel Port szeregowy I/O Wymiary płyty operacyjne go x1 Port LAN x1 Port USB2.0 x6 Gniazdo audio x3 200 mm (S) X 295 mm (W) Obsluga systemu Każde złącze obsługuje 1 Port drukarki Biostar zastrzega sobie prawo dodawania lub Windows XP / Vista / 7 odwoływania obsługi dowolnego systemu operacyjnego bez powiadomienia. 43 Motherboard Manual RUSSIAN СПЕЦ CPU (центральн Гнездо FM1 Архитектура AMD 64 разрешать обработка ый данных на 32 и 64 бит Процессоры AMD A-Series / E2-Series процессор) Набор микросхем AMD A55 Модуль памяти с двухканальным режимом DDR3 Слоты DDR3 DIMM x 2 Основная Максимальная ёмкость памяти 16ГБ память Каждый модуль DIMM поддерживает 512МБ/1ГБ/2ГБ/4ГБ/8ГБ DDR3 Super I/O Поддержка DDR3 800/1066/1333/1600/1866 Поддержка DDR3 2000 (OC) Не поддерживает зарегистрированные модули DIMM and ECC DIMM ITE 8728 Инициативы по охране окружающей среды, Обеспечивает наиболее используемые Аппаратный монитор действующие функциональные Регулятор скорости возможности Super I/O. Функция ITE "Smart Guardian" Интерфейс с низким количеством выводов (Интеллектуальная защита) SATA II Локальная сеть Встроенное последовательное устройство управления ATA скорость передачи данных до 3 гигабит/с. Соответствие спецификации SATA версия 2.0 Поддержка RAID 0,1,10 Автоматическое согласование 10 / 100 / 1000 RTL8111E / RTL8111F Мб/с Частичная / полная дуплексная способность Звуковой кодек Слоты Звуковая поддержка High-Definition VT1708B/ ALC662 5.1канальный звуковой выход Слот PCI Express Gen2 x16 x1 Слот PCI Express Gen2 x1 x2 Слот PCI x3 Встроенны Разъём SATA x6 Каждый разъём поддерживает 1 устройство SATA й разъём Разъём на лицевой панели x1 Поддержка устройств на лицевой панели Входной звуковой разъём x1 Разъём вывода для S/PDIF x1 44 Поддержка звуковых функций на лицевой панели Поддержка вывода цифровой звуковой функции A57A СПЕЦ Источник питания для вентилятора центрального Контактирующее приспособление вентилятора центрального процессора x1 Контактирующее приспособление вентилятора системы x1 процессора (с функцией интеллектуального вентилятора) Источник питания для вентилятора системы Открытое контактирующее приспособление CMOS x1 USB2.0-разъём x2 Разъём Порт подключения принтера Задняя Каждый разъём поддерживает 2 USB2.0-порта на лицевой панели Каждый разъём поддерживает 1 Порт x1 Разъем питания (24 вывод) x1 Разъем питания (4 вывод) x1 Клавиатура PS/2 x1 Мышь PS/2 x1 Последовательный порт x1 подключения принтера панель средств ввода-выв Порт LAN ода Размер панели Поддержка OS x1 USB2.0-порт x6 наушников x3 200 мм (Ш) X 295 мм (В) Biostar сохраняет за собой право добавлять или Windows XP / Vista / 7 удалять средства обеспечения для OS с или без предварительного уведомления. 45 Motherboard Manual ARABIC اﻟﻤﻮاﺻﻔﺎت وﺣﺪة اﻟﻤﻌﺎﻟﺠﺔ FM1ﻡﻘﺒﺲ اﻟﻤﺮآﺰﻳﺔ AMD A-Series / E2-Seriesﻡﻌﺎﻟﺠﺎت ﻡﺠﻤﻮﻋﺔ اﻟﺸﺮاﺋﺢ AMD A55 إﺝﺮاء اﻟﻌﻤﻠﻴﺎت اﻟﺤﺎﺳﻮﺏﻴﺔ ﺏﺴﺮﻋﺔ 32و 64ﺏﺖAMD 64ﺗﻤﻜﻦ ﺗﻘﻨﻴﺔ ﻡﺰدوﺝﺔ اﻟﻘﻨﺎةDDR3وﺣﺪة ذاآﺮة ﻓﺘﺤﺔ DDR3 DIMM ﻋﺪد2 ﺳﻌﺎت DDR3 1866/1600/1333/1066/800ﺗﺪﻋﻢ اﻟﺬاآﺮة ﻡﻦ ﻥﻮع ﺳﻌﺔ ذاآﺮة ﻗﺼﻮى 16ﺝﻴﺠﺎ ﺏﺎﻳﺖ اﻟﺬاآﺮة اﻟﺮﺋﻴﺴﻴﺔ ﻡﻴﺠﺎ ﺏﺎﻳﺖ ﻡﻴﺠﺎ /512ﺳﻌﺔ DDR3ﺗﺪﻋﻢ ذاآﺮة ﻡﻦ ﻥﻮع DIMMﺗﺪﻋﻢ آﻞ ﻓﺘﺤﺔ ) 2000 (OCﺳ ﻌﺎت DDR3ﻧ ﻮع ﻣﻦ اﻟﺬاآﺮة ﺗ ﺪﻋﻢ ﺏﺎﻳﺖ و /1و /2و /4و 8ﺝﻴﺠﺎ ﺏﺎﻳﺖ ECCوﺗﻠﻚ اﻟﺘﻲ ﻻ ﺗﺘﻮاﻓﻖ ﻡﻊ DIMMﻻ ﺗﺪﻋﻢ رﻗﺎﺋﻖ اﻟﺬاآﺮة وﺳﺎﺋﻞ اﻟﺘﺤﻜﻢ ﻓﻲ اﻟﺒﻴﺌﺔ: ITE 8728 Super I/O ﻡﺮاﻗﺐ ﻟﻤﻌﺮﻓﺔ ﺣﺎﻟﺔ اﻷﺝﻬﺰة اﻷآﺜﺮ اﺳﺘﺨﺪاﻡًﺎSuper I/O .ﺗﻮﻓﺮ وﻇﻴﻔﺔ ﻡﺮاﻗﺐ ﻓﻲ ﺳﺮﻋﺔ اﻟﻤﺮوﺣﺔ Low Pin Count Interfaceﺗﺪﻋﻢ ﺗﻘﻨﻴﺔ ITEﻡﻦ ""Smart Guardianوﻇﻴﻔﺔ ﻥﻘﻞ اﻟﺒﻴﺎﻥﺎت ﺏﺴﺮﻋﺎت ﺗﺼﻞ إﻟﻰ 3ﺝﻴﺠﺎﺏﺖ/ﺙﺎﻥﻴﺔ. SATA II 2.0اﻹﺹﺪارSATAﻡﻄﺎﺏﻘﺔ ﻟﻤﻮاﺹﻔﺎت ﻡﺘﻜﺎﻡﻞSerial ATAﻡﺘﺤﻜﻢ RAID 0,1,10ﺗﺪﻋﻢ ﺗﻘﻨﻴﺔ ﺗﻔﺎوض ﺗﻠﻘﺎﺋﻲ 100/10ﻣﻴﺠﺎ ﺑﺎیﺖ /ﺛﺎﻧﻴﺔ و1ﺝﻴﺠﺎ ﺑﺖ/ﺛﺎﻧﻴﺔ ﺵﺒﻜﺔ داﺥﻠﻴﺔ RTL8111E / RTL8111F آﻮدﻳﻚ اﻟﺼﻮت VT1708B/ ALC662 إﻣﻜﺎﻧﻴﺔ اﻟﻨﻘﻞ اﻟﻤﺰدوج اﻟﻜﺎﻣﻞ/اﻟﻨﺼﻔﻲ ﺗﺪﻋﻢ ﺗﻘﻨﻴﺔ اﻟﺼﻮت ﻋﺎﻟﻲ اﻟﺘﻌﺮﻳﻒ ﻡﻦ 5.1ﻗﻨﻮات ﻟﺨﺮج اﻟﺼﻮت اﻟﻔﺘﺤﺎت اﻟﻤﻨﺎﻓﺬ ﻋﻠﻰ ﺳﻄﺢ اﻟﻠﻮﺣﺔ ﻓﺘﺤﺔ PCI Express Gen2 x16 ﻋﺪد 1 ﻓﺘﺤﺔ PCI Express Gen2 x1 ﻋﺪد 2 ﻓﺘﺤﺔ PCI ﻋﺪد 3 ﻡﻨﻔﺬ SATA ﻋﺪد6 SATAﻳﺪﻋﻢ آﻞ ﻡﻨﻔﺬ واﺣﺪ ﻡﻦ أﺝﻬﺰة ﻡﻨﻔﺬ اﻟﻠﻮﺣﺔ اﻷﻡﺎﻡﻴﺔ ﻋﺪد 1 ﻳﺪﻋﻢ ﺗﺠﻬﻴﺰات اﻟﻠﻮﺣﺔ اﻷﻡﺎﻡﻴﺔ ﻡﻨﻔﺬ اﻟﺼﻮت اﻷﻡﺎﻡﻲ ﻋﺪد 1 ﻳﺪﻋﻢ وﻇﻴﻔﺔ اﻟﺼﻮت ﺏﺎﻟﻠﻮﺣﺔ اﻷﻡﺎﻡﻴﺔ ﻡﻨﻔﺬ ﺥﺮج S/PDIF ﻋﺪد 1 ﻳﺪﻋﻢ وﻇﻴﻔﺔ ﺥﺮج اﻟﺼﻮت اﻟﺮﻗﻤﻲ 46 A57A اﻟﻤﻮاﺻﻔﺎت ﻡﻨﺎﻓﺬ دﺥﻞ/ﺥﺮج اﻟﻠﻮﺣﺔ اﻟﺨﻠﻔﻴﺔ وﺹﻠﺔ ﻡﺮوﺣﺔ وﺣﺪة اﻟﻤﻌﺎﻟﺠﺔ اﻟﻤﺮآﺰﻳﺔ ﻋﺪد 1 Smart Fanﻟﺘﻮﺹﻴﻞ اﻟﻄﺎﻗﺔ ﻟﻤﺮوﺣﺔ وﺣﺪة اﻟﻤﻌﺎﻟﺠﺔ ﻡﻊ وﻇﻴﻔﺔ وﺹﻠﺔ ﻡﺮوﺣﺔ اﻟﻨﻈﺎم ﻋﺪ1 ﻟﺘﻮﺹﻴﻞ اﻟﻄﺎﻗﺔ ﻟﻤﺮوﺣﺔ اﻟﻨﻈﺎم وﺹﻠﺔ ﻡﺴﺢ CMOS ﻋﺪد 1 ﻡﻨﻔﺬ USB2.0 ﻋﺪد 2 ﻡﻨﻔﺬ ﻃﺎﺏﻌﺔ ﻋﺪد 1 ﻡﻨﻔﺬ ﺗﻮﺹﻴﻞ اﻟﻄﺎﻗﺔ )24دﺏﻮس( ﻋﺪد 1 ﻡﻨﻔﺬ ﺗﻮﺹﻴﻞ اﻟﻄﺎﻗﺔ )4دﺏﺎﺏﻴﺲ( ﻋﺪد 1 ﻟﻮﺣﺔ ﻡﻔﺎﺗﻴﺢ PS/2 ﻋﺪد 1 ﻡﺎوس PS/2 ﻋﺪد 1 ﻡﻨﻔﺬ ﺗﺴﻠﺴﻠﻲ ﻋﺪد 1 ﻡﻨﻔﺬ ﺵﺒﻜﺔ اﺗﺼﺎل ﻡﺤﻠﻴﺔ ﻋﺪد 1 ﻡﻨﺎﻓﺬ USB2.0 ﻋﺪد 6 ﻡﻘﺒﺲ ﺹﻮت ﻋﺪد 3 ﺣﺠﻢ اﻟﻠﻮﺣﺔ 295ﻡﻢ )ﻋﺮض( 200 Xﻡﻢ )ارﺗﻔﺎع( دﻋﻢ أﻥﻈﻤﺔ اﻟﺘﺸﻐﻴﻞ Windows XP / Vista / 7 ﻳﺪﻋﻢ آﻞ ﻡﻨﻔﺬ ﻓﺘﺤﺘﻲ USB2.0ﺏﺎﻟﻠﻮﺣﺔ اﻷﻡﺎﻡﻴﺔ ﺏﺤﻘﻬﺎ ﻓﻲ إﺿﺎﻓﺔ أو إزاﻟﺔ اﻟﺪﻋﻢ ﻷي ﻥﻈﺎم ﺗﺸﻐﻴﻞ ﺏﺈﺥﻄﺎر أو ﺏﺪون Biostarﺗﺤﺘﻔﻆ إﺥﻄﺎر. 47 Motherboard Manual JAPANESE 仕様 CPU Socket FM1 AMD 64アーキテクチャでは、32ビットと64ビット計算が AMD A-Series / E2-Series プロセッサ 可能です チップセット AMD A55 DDR3 DIMMスロット x 2 デュアル チャンネルモードDDR3メモリモジュール 最大メモリ容量16GB DDR3 800/1066/1333/1600/1866 をサポート メインメモリ 各DIMMは 512MB/1GB/2GB/4GB/8GB DDR3 DDR3 2000 (OC) をサポート Super I/O をサポート 登録済みDIMMとECC DIMMはサポートされません ITE 8728 環境コントロールイニシアチブ、 もっとも一般に使用されるレガシーSuper I/O機 H/Wモニター 能を採用しています。 ファン速度コントローラ/ モニター 低ピンカウントインターフェイス ITEの「スマートガーディアン」機能 最高3 Gb/秒のデータ転送速度 SATA II SATAバージョン2.0仕様に準拠。 統合シリアルATAコントローラ RAID 0,1,10のサポート LAN 10 / 100 / 1000 Mb/秒のオートネゴシエーション RTL8111E / RTL8111F 半/全二重機能 サウンド Codec スロット ハイデフィニションオーディオのサポート VT1708B/ ALC662 5.1 チャンネルオーディオアウト PCI Express Gen2 x16スロット x1 PCI Express Gen2 x1スロット x2 PCIスロット x3 オンボードコ SATAコネクタ ネクタ 48 x6 各コネクタは1つのSATAデバイスをサポートします フロントパネルコネクタ x1 フロントパネル機能をサポートします フロントオーディオコネクタ x1 フロントパネルオーディオ機能をサポートします S/PDIFアウトコネクタ x1 デジタルオーディオアウト機能をサポートします CPUファンヘッダ x1 CPUファン電源装置(スマートファン機能を搭載) システムファンヘッダ x1 システムファン電源装置 CMOSクリアヘッダ x1 A57A 仕様 各コネクタは2つのフロントパネルUSB2.0ポートをサポ USB2.0コネクタ x2 ートします 背面パネル I/O プリンタポートコネクタ x1 電源コネクタ(24ピン) x1 電源コネクタ(4ピン) x1 PS/2キーボード x1 PS/2マウス x1 シリアルポート x1 LANポート x1 USB2.0ポート x6 オーディオジャック x3 各コネクタは1つのプリンタポートをサポートします ボードサイズ 200 mm (幅) X 295 mm (高さ) OSサポート Windows XP / Vista / 7 Biostarは事前のサポートなしにOSサポートを追加または 削除する権利を留保します。 2012/04/06 49
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : Yes Create Date : 2012:04:06 09:42:26+08:00 Modify Date : 2012:04:06 09:42:26+08:00 Page Count : 51 Creation Date : 2012:04:06 01:42:26Z Mod Date : 2012:04:06 01:42:26Z Producer : Acrobat Distiller 5.0 (Windows) Author : 101001 Metadata Date : 2012:04:06 01:42:26Z Creator : 101001 Title : Microsoft Word - AA55E-A1S_120406.docEXIF Metadata provided by EXIF.tools