Biostar G41 M7 V7 X Owners Manual IG41A M7S_v2_120723

2014-07-31

: Biostar Biostar-G41-M7-V7-X-Owners-Manual biostar-g41-m7-v7-x-owners-manual biostar pdf

Open the PDF directly: View PDF .
Page Count: 51

Download
Open PDF In Browser	View PDF

G41-M7 Setup Manual

FCC Information and Copyright
This equipment has been tested and found to comply with the limits of a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. There is no guarantee that
interference will not occur in a particular installation.

The vendor makes no representations or warranties with respect to the contents
here and specially disclaims any implied warranties of merchantability or fitness
for any purpose. Further the vendor reserves the right to revise this publication
and to make changes to the contents here without obligation to notify any party
beforehand.
Duplication of this publication, in part or in whole, is not allowed without first
obtaining the vendor’s approval in writing.

The content of this user’s manual is subject to be changed without notice and we
will not be responsible for any mistakes found in this user’s manual. All the brand
and product names are trademarks of their respective companies.

Dichiarazione di conformità
sintetica
Ai sensi dell’art. 2 comma 3 del D.M.
275 del 30/10/2002
Si dichiara che questo prodotto è
conforme alle normative vigenti e
soddisfa i requisiti essenziali richiesti
dalle direttive
2004/108/CE, 2006/95/CE e
1999/05/CE
quando ad esso applicabili

Short Declaration of conformity
We declare this product is complying
with the laws in force and meeting all
the essential requirements as specified
by the directives
2004/108/CE, 2006/95/CE and
1999/05/CE
whenever these laws may be applied

Table of Contents
Chapter 1: Introduction.......................................... 1
1.1
1.2
1.3
1.4
1.5

Before You Start ................................................................................1
Package Checklist ............................................................................1
Motherboard Specifications .............................................................2
Rear Panel Connectors....................................................................3
Motherboard Layout..........................................................................4

Chapter 2: Hardware Installation ........................... 5
2.1
2.2
2.3
2.4
2.5
2.6
2.7

Install Central Processing Unit (CPU)............................................5
Install a Heatsink ...............................................................................7
Connect Cooling Fans......................................................................8
Install System Memory .....................................................................9
Expansion Slots...............................................................................11
Jumper Setting ................................................................................13
Herders & Connectors....................................................................14

Chapter 3: BIOS & Software ................................. 19
3.1
3.2
3.3

BIOS Setup ......................................................................................19
BIOS Update....................................................................................19
Software............................................................................................24

Chapter 4: Useful Help ......................................... 27
4.1
4.2
4.3
4.4

Driver Installation.............................................................................27
Extra Information .............................................................................28
AMI BIOS Beep Code.....................................................................29
Troubleshooting...............................................................................30

Appendix: Specifications In Other Languages ...... 32
German .................................................................................................................32
French ...................................................................................................................34
Italian .....................................................................................................................36
Spanish..................................................................................................................38
Portuguese ...........................................................................................................40
Polish .....................................................................................................................42
Russian .................................................................................................................44
Arabic.....................................................................................................................46
Japanese...............................................................................................................48

G41-M7

CHAPTER 1: INTRODUCTION
1.1

Before You Start

Thank you for choosing our product. Before you start installing the
motherboard, please make sure you follow the instructions below:
Prepare a dry and stable working environment with sufficient
lighting.
Always disconnect the computer from power outlet before
operation.
Before you take the motherboard out from anti-static bag,
ground yourself properly by touching any safely grounded
appliance, or use grounded wrist strap to remove the static
charge.
Avoid touching the components on motherboard or the rear
side of the board unless necessary. Hold the board on the
edge, do not try to bend or flex the board.
Do not leave any unfastened small parts inside the case after
installation. Loose parts will cause short circuits which may
damage the equipment.
Keep the computer from dangerous area, such as heat
source, humid air and water.
The operating temperatures of the computer should be 0 to
45 degrees Celsius.
To avoid injury, be careful of:
Sharp pins on headers and connectors
Rough edges and sharp corners on the chassis
Damage to wires that could cause a short circuit

1.2

Package Checklist
;
;
;
;

Serial ATA Cable x2
Rear I/O Panel for ATX Case x1
Installation Guide x1
Fully Setup Driver DVD x1

Note: The package contents may be different due to the sales region or models in which it was sold.
For more information about the standard package in your region, please contact your dealer or sales
representative.

Motherboard Manual

1.3

Motherboard Specifications
SPEC
LGA 775

CPU

Intel Core2Duo / Core2Quad /

Supports Hyper-Threading / Execute Disable Bit / Enhanced

Pentium Dual-Core / Celeron Dual-Core /

Intel SpeedStep® / Intel Architecture-64 / Extended Memory 64

Celeron 4xx processor

Technology / Virtualization Technology

(Maximum Watt: 95W)
FSB

Support 533 / 800 / 1066 / 1333 MHz , FSB533 only support DDR2-533
Intel G41

Chipset
Intel ICH7
ITE 8728F-BX

Environment Control initiatives,

Provides the most commonly used legacy Super Hardware Monitor Controller
Super I/O
I/O functionality.

Fan Speed Controller

Low Pin Count Interface

ITE's "Smart Guardian" function

DIMM Slots x 2

Dual Channel Mode DDR2 memory module

Each DIMM supports 256MB / 512MB / 1GB /

Supports DDR2-533/ 800/1066(OC),

2GB/ 4GB DDR2

DDR2-533 only for FSB1066 / 533

Max Memory Capacity 8GB

Registered DIMM and ECC DIMM is not supported

Graphics

GMA X4500

Max Shared Video Memory is 256MB

IDE

Integrated IDE Controller

Main Memory

Ultra DMA 33 / 66 / 100 Bus Master Mode
supports PIO Mode 0~4
Data transfer rates up to 3.0 Gb/s.
SATA 2

Integrated Serial ATA Controller
SATA Version 2.0 specification compliant
10 / 100 Mb/s auto negotiation

LAN

Realtek RTL 8105E
Half / Full duplex capability
5.1 channels audio out

Sound Codec ALC662
High Definition Audio
PCI slot

Supports PCI expansion cards

PCI Express x 16 slot

Supports PCI-E x16 expansion cards

On Board

Printer Port Connector

Each connector supports 1 Printer port

Connectors

Serial port Connector

Connects to RS-232 Port

IDE Connector

Each connector supports 2 IDE device

Slots

G41-M7
SPEC
SATA Connector

Each connector supports 1 SATA devices

Front Panel Connector

Supports front panel facilities

Front Audio Connector

Supports front panel audio function

CPU Fan Header

CPU Fan power supply (with Smart Fan function)

System Fan Header

System Fan Power supply

Clear CMOS Header

Restore CMOS data to factory default

USB 2.0 Connector

Each connector supports 2 front panel USB ports

Power Connector (24pin)

Connects to Power supply

Power Connector (4pin)

Connects to Power supply

PS/2 Keyboard

Connects to PS/2 Keyboard

PS/2 Mouse

Connects to PS/2 Mouse

Back Panel

VGA port

Connect to D-SUB monitor

I/O

LAN port

Connect to RJ-45 ethernet cable

USB 2.0 Port

Connect to USB devices

Audio Jack

Provide Audio-In/Out and microphone connection

Board Size

182 (W) x 235 (L) mm

OS Support

Windows 2000 / XP / Vista / 7 / 8

Biostar reserves the right to add or remove support for any OS
with or without notice

1.4

Rear Panel Connectors

Since the audio chip supports High Definition Audio Specification, the function of each audio
jack can be defined by software. The input / output function of each audio jack listed above
represents the default setting. However, when connecting external microphone to the audio port,
please use the Line In (blue) and Mic In (Pink) audio jack.

Motherboard Manual

1.5

Motherboard Layout

Note: ■ represents the 1st pin.

G41-M7

CHAPTER 2: HARDWARE INSTALLATION
2.1

Install Central Processing Unit (CPU)

Step 1: Locate the CPU socket on the motherboard

Note: Remove Pin Cap before installation, and make good preservation for future use. When
the CPU is removed, cover the Pin Cap on the empty socket to ensure pin legs won’t be
damaged.

Pin-Cap
Step 2: Pull the socket locking lever out from the socket and then raise the lever
up to a 90-degree angle.

Motherboard Manual
Step 3: Look for the triangular cut edge on socket, and the golden dot on CPU
should point forwards this triangular cut edge.
Step 3-1:

Step 3-2:

Step 4: Hold the CPU down firmly, and then lower the lever to locked position to
complete the installation.

Note: The CPU fits only in one correct orientation. Do not force the CPU into the socket
to prevent damaging the CPU.

G41-M7

2.2

Install a Heatsink

Step 1: Place the CPU fan assembly on top of the installed CPU and make sure
that the four fasteners match the motherboard holes. Orient the assembly
and make the fan cable is closest to the CPU fan connector.

Step 2: Press down two fasteners at one time in a diagonal sequence to secure
the CPU fan assembly in place. Ensure that all four fasteners are secured.

Note1: Do not forget to connect the CPU fan connector.
Note2: For proper installation, please kindly refer to the installation manual of your CPU
heatsink.

Motherboard Manual

2.3

Connect Cooling Fans

These fan headers support cooling-fans built in the computer. The fan cable and
connector may be different due to the fan manufacturer. Connect the fan cable to
the connector while matching the black wire to pin#1.

CPU_FAN1: CPU Fan Header

Pin
1
2
3
4

Assignment
Ground
Power
FAN RPM rate sense
Smart Fan Control

Pin
1
2
3

Assignment
Ground
+12V
FAN RPM rate sense

SYS_FAN1: System Fan Header

Note: CPU_FAN1 & SYS_FAN1 support 4-pin and 3-pin head connectors. When connecting
with wires onto connectors, please note that the red wire is the positive and should be
connected to pin#2, and the black wire is Ground and should be connected to GND.

G41-M7

2.4

Install System Memory

A. DDR2 module

Step 1: Unlock a DIMM slot by pressing the retaining clips outward. Align a DIMM
on the slot such that the notch on the DIMM matches the break on the slot.

Step 2: Insert the DIMM vertically and firmly into the slot until the retaining chip snap
back in place and the DIMM is properly seated.

Note: If the DIMM does not go in smoothly, do not force it. Pull it all the way out and try again.

Motherboard Manual

B. Memory Capacity
DIMM Socket
Location

DDR2 Module

Total Memory
Size

DDR2_A1

256MB/512MB/1GB/2GB/4GB

DDR2_B1

256MB/512MB/1GB/2GB/4GB

Max is 8GB.

C. Dual Channel Memory Installation
Please refer to the following requirements to activate Dual Channel function:
Install memory module of the same density in pairs, shown in the table.
Dual Channel Status

DDR2_A1

Disabled

Enabled

DDR2_B1

(O means memory installed; X, not installed.)
Note1: The DRAM bus width of the memory module must be the same(x8 or x16)
Note2: DDR2-533 only for FSB 1066 / 533

G41-M7

2.5

Expansion Slots

PEX16_1: PCI-Express x16 Slot
-

PCI-Express 1.0a compliant.
Maximum theoretical realized bandwidth of 4GB/s simultaneously per
direction, for an aggregate of 8GB/s totally.
PCI-Express supports a raw bit-rate of 2.5Gb/s on the data pins.
2X bandwidth over the traditional PCI architecture.

PCI1/PCI2: Peripheral Component Interconnect Slots
This motherboard is equipped with 2 standard PCI slots. PCI stands for
Peripheral Component Interconnect, and it is a bus standard for expansion
cards. This PCI slot is designated as 32 bits.

Motherboard Manual

Install an Expansion Card
You can install your expansion card by following steps:
1.
Read the related expansion card's instruction document before install the
expansion card into the computer.
2.
Remove your computer's chassis cover, screws and slot bracket from the
computer.
3.
Place a card in the expansion slot and press down on the card until it is
completely seated in the slot.
4.
Secure the card’s metal bracket to the chassis back panel with a screw.
5.
Replace your computer's chassis cover.
6.
Power on the computer, if necessary, change BIOS settings for the
expansion card.
7.
Install related driver for the expansion card.

G41-M7

2.6

Jumper Setting

The illustration shows how to set up jumpers. When the jumper cap is placed on
pins, the jumper is “close”, if not, that means the jumper is “open”.

Pin opened

Pin closed

Pin1-2 closed

JCMOS1: Clear CMOS Header
Placing the jumper on pin2-3 allows user to restore the BIOS safe setting and
the CMOS data. Please carefully follow the procedures to avoid damaging the
motherboard.
3
1
Pin 1-2 Close:
Normal Operation (Default).

3
1
Pin 2-3 Close:
Clear CMOS data.

※ Clear CMOS Procedures:
1.
Remove AC power line.
2.
Set the jumper to “Pin 2-3 close”.
3.
Wait for five seconds.
4.
Set the jumper to “Pin 1-2 close”.
5.
Power on the AC.
6.
Reset your desired password or clear the CMOS data.

Motherboard Manual

2.7

Herders & Connectors

ATXPWR1: ATX Power Source Connector
By connecting this connector, it will provide +12V to CPU power circuit.

Pin
1
2
3
4

Assignment
+12V
+12V
Ground
Ground

ATXPWR2: ATX Power Source Connector
This connector allows user to connect 24-pin power connector on the ATX
power supply.

Pin
13
14
15
16
17
18
19
20
21
22
23
24

Assignment
+3.3V
-12V
Ground
PS_ON
Ground
Ground
Ground
NC
+5V
+5V
+5V
Ground

Pin
1
2
3
4
5
6
7
8
9
10
11
12

Assignment
+3.3V
+3.3V
Ground
+5V
Ground
+5V
Ground
PW_OK
Standby Voltage+5V
+12V
+12V
+3.3V

Note1: Before you power on the system, please make sure that both ATXPWR1 and
ATXPWR2 connectors have been plugged-in.
Note2: Insufficient power supplied to the system may result in instability or the peripherals
not functioning properly. Use of a PSU with a higher power output is recommended when
configuring a system with more power-consuming devices.
14

G41-M7

PANEL1: Front Panel Header
This 16-pin connector includes Power-on, Reset, HDD LED, Power LED, and
speaker connection. It allows user to connect the PC case’s front panel switch
functions.

Assignment

+5V

N/A

Speaker

Function

Assignment

Function

N/A

Speaker

N/A

Connector

N/A

Power LED (+)

N/A
N/A

HDD LED (+)

Hard drive

Power LED (+)

HDD LED (-)

LED

Power LED (-)

Ground

Reset control

Reset button

Power button

Ground

Power LED

Power-on button

F_AUDIO1: Front Panel Audio Header
This header allows user to connect the front audio output cable with the PC front
panel. This header allows only HD audio front panel connector; AC’97 connector
is not acceptable.

Pin
1
2
3
4
5
6
7
8
9
10

Assignment
Mic Left in
Ground
Mic Right in
GPIO
Right line in
Jack Sense
Front Sense
Key
Left line in
Jack Sense

Motherboard Manual

F_USB1/F_USB2: Headers for USB 2.0 Ports at Front Panel
This motherboard provides 2 USB 2.0 headers, which allows user to connect
additional USB cable on the PC front panel, and also can be connected with
internal USB devices, like USB card reader.
Pin
1
2
3
4
5
6
7
8
9
10

Assignment
+5V (fused)
+5V (fused)
USBUSBUSB+
USB+
Ground
Ground
Key
NC

IDE1: Hard Disk Connector
The motherboard has a 32-bit Enhanced PCI IDE Controller that provides PIO
Mode 0~4, Bus Master, and Ultra DMA 33/66/100 functionality.
The IDE connector can connect a master and a slave drive, so you can connect
up to two hard disk drives.

G41-M7

SATA1~SATA4: Serial ATA Connectors
The motherboard has a PCI to SATA Controller with 4channels SATA interface, it
satisfies the SATA 2.0 spec and with transfer rate of 3Gb/s.
Pin
1
2
3
4
5
6
7

Assignment
Ground
TX+
TXGround
RXRX+
Ground

JCOM1: Serial port Connector
The motherboard has a Serial Port Connector for connecting RS-232 Port.

Assignment

1
2
3
4
5
6
7
8
9
10

Carrier detect
Received data
Transmitted data
Data terminal ready
Signal ground
Data set ready
Request to send
Clear to send
Ring indicator
Key

Motherboard Manual

JPRNT1: Printer Port Connector
This header allows you to connector printer on the PC.

Pin
1
2
3
4
5
6
7
8
9
10
11
12
13

Assignment
-Strobe
-ALF
Data 0
-Error
Data 1
-Init
Data 2
-Scltin
Data 3
Ground
Data 4
Ground
Data 5

Pin
14
15
16
17
18
19
20
21
22
23
24
25
26

Assignment
Ground
Data 6
Ground
Data 7
Ground
-ACK
Ground
Busy
Ground
PE
Ground
SCLT
Key

G41-M7

CHAPTER 3: BIOS & SOFTWARE
3.1

3.2

BIOS Setup
For better system performance, the BIOS firmware is being
continuously updated. The BIOS information described below in this
manual is for your reference only and the actual BIOS information
and settings on board may be different from this manual
For further information of setting up the BIOS, please refer to the
BIOS Manual in the Setup DVD.

BIOS Update
There are three ways to update the BIOS:
BIOS Update Utility, BIOS Online Update Utility and BIOS Flasher.

1. BIOS Update Utility
1. Installing BIOS Update Utility from the DVD Driver.
2. Download the proper BIOS from www.biostar.com.tw .
AWARD BIOS

Show current BIOS information

AMI BIOS

Clear CMOS function
(Only for AWARD BIOS)

Save current BIOS
to a .bin file

Update BIOS
with a BIOS file

Motherboard Manual

Once click on this button, the saving
dialog will show. Choose the position to
save file and enter file name. (We
recommend that the file name should be
English/number and no longer than 7
characters.) Then click Save.

After the saving process, finish dialog
will show. Click on OK to complete the
BIOS Backup procedure.

Before doing this, please download the proper BIOS file from the website.
For AWARD BIOS, update BIOS
procedure should be run with Clear
CMOS function, so please check on
Clear CMOS first.
Then click Update BIOS button, a
dialog will show for asking you backup
current BIOS. Click Yes for BIOS
backup and refer to the Backup BIOS
procedure; or click No to skip this
procedure.

After the BIOS Backup procedure, the
open dialog will show for requesting the
BIOS file which is going to be updated.
Please choose the proper BIOS file for
updating, then click on Open.

G41-M7
The utility will update BIOS with the
proper BIOS file, and this process may
take minutes. Please do not open any
other applications during this process.

After the BIOS Update process, click on
OK to restart the system.

While the system boots up and the full screen logo shows, press
key to enter BIOS setup.

In the BIOS setup, use the Load Optimized Defaults function and then Save and
Exit Setup to exit BIOS setup. BIOS Update is completed.

2. Online Update Utility
1. Installing BIOS Update Utility from the DVD Driver.
2. Please make sure the system is connected to the internet before using this
function.

3. Open BIOS Update Utility and
click the Online Update button
on the main screen.

4. An open dialog will show up to
request your agreement to
start the BIOS update. Click
Yes to start the online update
procedure.

Motherboard Manual

5. If there is a new BIOS version,
the utility will ask you to
download it. Click Yes to
proceed.

6. After the download is
completed, you will be asked
to program (update) the BIOS
or not. Click Yes to proceed.

7. After the updating process is
finished, you will be asked you
to reboot the system. Click
OK to reboot.

8. While the system boots up and the full screen logo shows up, press
key to enter BIOS setup.
After entering the BIOS setup, please go to the Save & Exit, using the Restore
Defaults function to load Optimized Defaults, and select Save Changes and
Reset to restart the computer. Then, the BIOS Update is completed.

G41-M7

3. BIOSTAR BIOS Flasher
BIOSTAR BIOS Flasher is a BIOS flashing utility providing you an easy and
simple way to update your BIOS via USB pen drive.
Note1: This utility only allows storage device with FAT32/16 format and single partition.
Note2: Shutting down or resetting the system while updating the BIOS will lead to system
boot failure.

The BIOSTAR BIOS Flasher is built in the BIOS ROM. To enter the utility, press
during the Power-On Self Tests (POST) procedure while booting up.
Updating BIOS with BIOSTAR BIOS Flasher
1. Go to the website to download the latest BIOS file for the motherboard.
2. Then, save the BIOS file into a USB pen
drive or a floppy disk.
3. Insert the USB pen drive or the floppy disk
that contains the BIOS file to the USB port
or the floppy disk drive.
4. Power on or reset the computer and then
press during the POST process. A
select dialog as the picture on the right
appears. Select the device contains the
BIOS file and press to enter the
utility.
5. The utility will show the BIOS files and their respective information. Select
the proper BIOS file and press then to perform the BIOS
update process.
6. After the update process,
the utility will ask you to
reboot the system.
Press to proceed.
BIOS update completes.

Motherboard Manual

3.3

Software

Installing Software
1. Insert the Setup DVD to the optical drive. The driver installation program would
appear if the Autorun function has been enabled.
2. Select Software Installation, and then click on the respective software title.
3. Follow the on-screen instructions to complete the installation.
Note1: All the information and content about following software are subject to be changed without
notice. For better performance, the software is being continuously updated.
Note2: The information and pictures described below are for your reference only. The actual
information and settings on board may be slightly different from this manual.

Launching Software
After the installation process is completed, you will see the software icon showing on
the desktop. Double-click the icon to launch it.

eHot-Line (Optional)
eHot-Line is a convenient utility that helps you to contact with our Tech-Support system.
This utility will collect the system information which is useful for analyzing the problem
you may have encountered, and then send these information to our tech-support
department to help you fix the problem.
Note: Before you use this utility, please set Outlook Express as your default e-mail client application program.
represents important
information that you
must provide. Without
this information, you may
not be able to send out
the mail.

This block will show
the information which
would be collected in
the mail.

condition
*Describe
of your system.

your area or
*Select
the area close to you.
Provide the e-mail
address that you would
like to send the copy to.
the name of
*Provide
the memory module
manufacturer.

Provide the name of
the power supply
manufacturer and the
model no.
Send the mail out.

Exit this dialog.

Save these information to a .txt file

G41-M7

After filling up this information, click “Send”
to send the mail out. A warning dialog would
appear asking for your confirmation; click
“Send” to confirm or “Do Not Send” to cancel.

If you want to save this information to a .txt file, click “Save As…” and then you will see
a saving dialog appears asking you to enter file name.

Enter the file name and then click “Save”.
Your system information will be saved to
a .txt file.

Open the saved .txt file, you will see
your system information including
motherboard/BIOS/CPU/video/
device/OS information. This information
is also concluded in the sent mail.

Note1: We will not share customer’s data with any other third parties, so please feel free to
provide your system information while using eHot-Line service.
Note2: If you are not using Outlook Express as your default e-mail client application, you may
need to save the system information to a .txt file and send the file to our tech support with other
e-mail application. Go to the following web http://www.biostar.com.tw/app/en/about/contact.php for
getting our contact information.

Motherboard Manual

BIOScreen Utility (Optional)
This utility allows you to personalize your boot logo easily. You can choose
BMP as your boot logo so as to customize your computer.

Please follow the following instructions to update boot logo:
1. Load Image：Choose the picture as the boot logo.
2. Transform：Transform the picture for BIOS and preview the result.
3. Update Bios：Write the picture to BIOS Memory to complete the update.

G41-M7

CHAPTER 4: USEFUL HELP
4.1

Driver Installation

After you installed your operating system, please insert the Fully Setup Driver
DVD into your optical drive and install the driver for better system performance.
You will see the following window after you insert the DVD

The setup guide will auto detect your motherboard and operating system.
Note: If this window didn’t show up after you insert the Driver DVD, please use file browser
to locate and execute the file SETUP.EXE under your optical drive.

A. Driver Installation
To install the driver, please click on the Driver icon. The setup guide will list the
compatible driver for your motherboard and operating system. Click on each
device driver to launch the installation program.

B. Software Installation
To install the software, please click on the Software icon. The setup guide will list
the software available for your system, click on each software title to launch the
installation program.

C. Manual
Aside from the paperback manual, we also provide manual in the Driver DVD.
Click on the Manual icon to browse for available manual.
Note: You will need Acrobat Reader to open the manual file. Please download the latest
version of Acrobat Reader software from http://get.adobe.com/reader/

Motherboard Manual

4.2

Extra Information

CPU Overheated
If the system shutdown automatically after power on system for seconds, that
means the CPU protection function has been activated.
When the CPU is over heated, the motherboard will shutdown automatically to
avoid a damage of the CPU, and the system may not power on again.
In this case, please double check:
1. The CPU cooler surface is placed evenly with the CPU surface.
2. CPU fan is rotated normally.
3. CPU fan speed is fulfilling with the CPU speed.
After confirmed, please follow steps below to relief the CPU protection
function.
1. Remove the power cord from power supply for seconds.
2. Wait for seconds.
3. Plug in the power cord and boot up the system.
Or you can:
1. Clear the CMOS data.
(See “Close CMOS Header: JCMOS1” section)
2. Wait for seconds.
3. Power on the system again.

G41-M7

4.3

AMI BIOS Beep Code

Boot Block Beep Codes
Number of Beeps
1
2
3
4
5
7
10
11
12
13

Description
No media present. (Insert diskette in floppy drive A:)
“AMIBOOT.ROM” file not found in root directory of diskette in
A:
Insert next diskette if multiple diskettes are used for recovery
Flash Programming successful
File read error
No Flash EPROM detected
Flash Erase error
Flash Program error
“AMIBOOT.ROM” file size error
BIOS ROM image mismatch (file layout does not match
image present in flash device)

POST BIOS Beep Codes
Number of Beeps
1
3
6
7
8

Description
Memory refresh timer error
Base memory read/write test error
Keyboard controller BAT command failed
General exception error (processor exception interrupt error)
Display memory error (system video adapter)

Troubleshooting POST BIOS Beep Codes
Number of Beeps
1, 3

6, 7

Troubleshooting Action
Reseat the memory, or replace with known good modules.
Fatal error indicating a serious problem with the system.
Consult your system manufacturer. Before declaring the
motherboard beyond all hope, eliminate the possibility of
interference by a malfunctioning add-in card. Remove all
expansion cards except the video adapter.
z If beep codes are generated when all other expansion
cards are absent, consult your system manufacturer’s
technical support.
z If beep codes are not generated when all other expansion
cards are absent, one of the add-in cards is causing the
malfunction. Insert the cards back into the system one at a
time until the problem happens again. This will reveal the
malfunctioning card.
If the system video adapter is an add-in card, replace or
reseat the
video adapter. If the video adapter is an integrated part of the
system board, the board may be faulty.

Motherboard Manual

4.4

Troubleshooting
Probable

Solution

There is no power in the system. 1.
Power LED does not shine; the
fan of the power supply does not 2.
work
3.
Indicator light on keyboard does
not shine.

Make sure power cable is
securely plugged in.
Replace cable.
Contact technical support.

System is inoperative. Keyboard lights Using even pressure on both ends of
are on, power indicator lights are lit,
the DIMM, press down firmly until the
and hard drives are running.
module snaps into place.
System does not boot from a hard disk 1.
drive, but can be booted from optical
drive.
2.

System only boots from an optical
drive. Hard disks can be read,
applications can be used, but system
fails to boot from a hard disk.

Screen message shows “Invalid
Configuration” or “CMOS Failure.”

Review system’s equipment. Make sure
correct information is in setup.

System cannot boot after user installs a 1.
second hard drive.
2.

Check cable running from disk to
disk controller board. Make sure
both ends are securely plugged
in; check the drive type in the
standard CMOS setup.
Backing up the hard drive is
extremely important. All hard
disks are capable of breaking
down at any time.
Back up data and applications
files.
Reformat the hard drive.
Re-install applications and data
using backup disks.

Set master/slave jumpers
correctly.
Run SETUP program and select
correct drive types. Call the drive
manufacturers for compatibility
with other drives.

G41-M7

This page is intentionally left blank.

Motherboard Manual

APPENDIX: Specifications In Other Languages
German
Spezifikationen
LGA 775
Unterstützt Hyper-Threading / Execute Disable Bit /
Intel Core2Duo / Core2Quad / Pentium Dual-Core
CPU

Enhanced Intel SpeedStep® / Intel Architecture-64 /
/ Celeron Dual-Core / Celeron 4xx Prozessoren
Extended Memory 64 Technology / Virtualization Technology
(Maximales Watt: 95W)

FSB

533 / 800 / 1066 / 1333 MHz, FSB533 unterstützt nur DDR2-533
Intel G41

Chipsatz
Intel ICH7
ITE 8728F-BX

Umgebungskontrolle,

Bietet die häufig verwendeten alten Super

Hardware-Überwachung

E/A-Funktionen.

Lüfterdrehzahl-Controller/-Überwachung

Low Pin Count-Schnittstelle

"Smart Guardian"-Funktion von ITE

DDR2 DIMM-Steckplätze x 2

Dual-Kanal DDR2 Speichermodul

Jeder DIMM unterstützt 256MB / 512MB / 1GB /

Unterstützt DDR2-533/ 800/1066(OC)

2GB/ 4GB DDR2.

DDR2-533 nur für FSB1066 / 533

Max. 8GB Arbeitsspeicher

registrierte DIMMs. ECC DIMMs werden nicht unterstützt.

Grafik

GMA X4500

Max. 256MB gemeinsam benutzter Videospeicher

IDE

Integrierter IDE-Controller

Super E/A

Arbeitsspeicher

Ultra DMA 33 / 66 / 100 Bus Master-Modus
Unterstützt PIO-Modus 0~4,
Datentransferrate bis zu 3.0Gb/s
SATA

Integrierter Serial ATA-Controller
Konform mit der SATA-Spezifikation Version 2.0.
10 / 100 Mb/s Auto-Negotiation

LAN

Realtek RTL 8105E
Halb-/ Vollduplex-Funktion

HD
Unterstützt High-Definition Audio
Audio-Unterstüt ALC662
5.1-Kanal-Audioausgabe
zung
PCI-Steckplatz

PCI Express x16 Steckplatz

Steckplätze

G41-M7
Spezifikationen
Druckeranschluss Anschluss

Jeder Anschluss unterstützt 1 Druckeranschluss

Serieller Anschluss

IDE-Anschluss

Jeder Anschluss unterstützt 2 IDE-Laufwerke

SATA-Anschluss

Jeder Anschluss unterstützt 1 SATA-Laufwerk

Fronttafelanschluss

Unterstützt die Fronttafelfunktionen

Front-Audioanschluss

Unterstützt die Fronttafel-Audioanschlussfunktion

CPU-Lüfter-Sockel

Onboard-Ansc
CPU-Lüfterstromversorgungsanschluss (mit Smart
hluss

Fan-Funktion)
System-Lüfter-Sockel

"CMOS löschen"-Sockel

USB-Anschluss

Stromanschluss (24-polig)

Stromanschluss (4-polig)

PS/2-Tastatur

PS/2-Maus

VGA-Anschluss

LAN-Anschluss

USB-Anschluss

Audioanschluss

System-Lüfter-Stromversorgungsanschluss

Jeder Anschluss unterstützt 2 Fronttafel-USB-Anschlüsse

Rückseiten-E/A

Platinengröße

182 mm (B) X 235 mm (L)
Biostar behält sich das Recht vor, ohne Ankündigung die

OS-Unterstützu
Windows 2000 / XP / Vista / 7 / 8

Unterstützung für ein Betriebssystem hinzuzufügen oder zu

ng
entfernen.

Motherboard Manual

French
SPEC
LGA 775
Prend en charge les technologies Hyper-Threading /
Processeurs Intel Core2Duo / Core2Quad /
d'exécution de bit de désactivation / Intel SpeedStep®
UC

Pentium Dual-Core / Celeron Dual-Core /
optimisée/ d'architecture Intel 64 / de mémoire étendue 64 / de
Celeron 4xx
virtualisation
(Watt maximum : 95W)

Bus frontal

533 / 800 / 1066 / 1333 MHz, FSB533 seul soutien DDR2-533
Intel G41

Chipset
Intel ICH7
ITE 8728F-BX

Initiatives de contrôle environnementales,

Fournit la fonctionnalité de Super E/S

Moniteur de matériel

patrimoniales la plus utilisée.

Contrôleur /moniteur de vitesse de ventilateur

Interface à faible compte de broches

Fonction "Gardien intelligent" de l'ITE

Super E/S

Module de mémoire DDR2 à mode à double voie
Fentes DDR2 DIMM x 2
Prend en charge la DDR2-533/ 800/1066(OC)
Mémoire

Chaque DIMM prend en charge des DDR2 de

principale

256Mo / 512Mo / 1Go / 2Go / 4Go

DDR2-533 seulement pour un FSB1066 / 533
Les DIMM à registres et DIMM avec code correcteurs d'erreurs
Capacité mémoire maximale de 8Go
ne sont pas prises en charge
Graphiques

GMA X4500

IDE

Contrôleur IDE intégré

Mémoire vidéo partagée maximale de 256 Mo
Mode principale de Bus Ultra DMA 33 / 66 / 100
Prend en charge le mode PIO 0~4,
Taux de transfert jusqu'à 3.0Go/s.

SATA
Contrôleur Serial ATA intégré

Conforme à la spécification SATA Version 2.0
10 / 100 Mb/s négociation automatique
LAN

Realtek RTL 8105E
Half / Full duplex capability

Prise en
Prise en charge de l'audio haute définition
charge audio ALC662
Sortie audio à 5.1 voies
HD
Fentes

Fente PCI

G41-M7
SPEC
Fente PCI Express x16

Connecteur de Port d'imprimante

Port série

Connecteur IDE

Chaque connecteur prend en charge 2 périphériques IDE

Connecteur SATA

Chaque connecteur prend en charge 1 périphérique SATA

Connecteur du panneau avant

Prend en charge les équipements du panneau avant

Connecteur Audio du panneau avant x1

Chaque connector prend en charge 1 Port d'imprimante

Prend en charge la fonction audio du panneau avant
Alimentation électrique du ventilateur UC (avec fonction de

Connecteur
embarqué

Embase de ventilateur UC

x1
ventilateur intelligent)

Embase de ventilateur système

Embase d'effacement CMOS

Connecteur USB

Alimentation électrique du ventilateur système

Chaque connecteur prend en charge 2 ports USB de panneau
avant
Connecteur d'alimentation

(24 broches)
Connecteur d'alimentation

(4 broches)
Clavier PS/2

Souris PS/2

Port VGA

Port LAN

Port USB

Fiche audio

E/S du
panneau
arrière

Dimensions
182 mm (l) X 235 mm (H)
de la carte
Biostar se réserve le droit d'ajouter ou de supprimer le support
Support SE

Windows 2000 / XP / Vista / 7 / 8
de SE avec ou sans préavis.

Motherboard Manual

Italian
SPECIFICA
LGA 775
Supporto di Hyper-Threading / Execute Disable Bit /
Processore Intel Core2Duo / Core2Quad /
Enhanced Intel SpeedStep® / Architettura Intel 64 /
CPU

Pentium Dual-Core / Celeron Dual-Core /
Tecnologia Extended Memory 64 / Tecnologia
Celeron 4xx
Virtualization
(Watt massimo: 95W)

FSB

533 / 800 / 1066 / 1333 MHz, FSB533 solo supporto DDR2-533
Intel G41

Chipset
Intel ICH7
ITE 8728F-BX

Funzioni di controllo dell’ambiente:

Fornisce le funzionalità legacy Super I/O

Monitoraggio hardware

usate più comunemente.

Controller / Monitoraggio velocità ventolina

Interfaccia LPC (Low Pin Count)

Funzione "Smart Guardian" di ITE

Alloggi DIMM DDR2 x 2

Modulo di memoria DDR2 a canale doppio

Memoria

Ciascun DIMM supporta DDR2 256MB /

Supporto di DDR2-533/ 800/1066(OC)

principale

512MB / 1GB / 2GB / 4GB

DDR2-533 solo per FSB1066 / 533

Capacità massima della memoria 8GB

DIMM registrati e DIMM ECC non sono supportati

Grafica

GMA X4500

La memoria video condivisa massima è di 256MB

IDE

Controller IDE integrato

Super I/O

Modalità Bus Master Ultra DMA 33 / 66 / 100
Supporto modalità PIO Mode 0-4
Velocità di trasferimento dei dati fino a 3.0Gb/s.
SATA

Controller Serial ATA integrato
Compatibile specifiche SATA Versione 2.0.
Negoziazione automatica 10 / 100 Mb/s

LAN

Realtek RTL 8105E
Capacità Half / Full Duplex
Supporto audio High-Definition (HD)

Supporto
ALC662
audio HD

Uscita audio 5.1 canali
Alloggio PCI

Alloggio PCI Express x16

Alloggi

G41-M7
SPECIFICA

Connettori
su scheda

Connettore Porta stampante

Ciascun connettore supporta 1 Porta stampante

Porta seriale

Connettore IDE

Ciascun connettore supporta 2 unità IDE

Connettore SATA

Ciascun connettore supporta 1 unità SATA

Connettore pannello frontale

Supporta i servizi del pannello frontale

Connettore audio frontale

Supporta la funzione audio pannello frontale

Collettore ventolina CPU

Alimentazione ventolina CPU (con funzione Smart Fan)

Collettore ventolina sistema

Alimentazione ventolina di sistema

Collettore cancellazione CMOS

Connettore USB

Ciascun connettore supporta 2 porte USB pannello
frontale
Connettore alimentazione

(24 pin)
Connettore alimentazione

(4 pin)
Tastiera PS/2

Mouse PS/2

I/O pannello Porta VGA

Porta LAN

Porta USB

Connettore audio

posteriore

Dimensioni
182 mm (larghezza) x 235 mm (altezza)
scheda
Sistemi
operativi
supportati

Biostar si riserva il diritto di aggiungere o rimuovere il
Windows 2000 / XP / Vista / 7 / 8

supporto di qualsiasi sistema operativo senza
preavviso.

Motherboard Manual

Spanish
Especificación
LGA 775

CPU

Procesador Intel Core2Duo / Core2Quad /

Admite Hyper-Threading / Bit de deshabilitación de ejecución /

Pentium Dual-Core / Celeron Dual-Core /

Intel SpeedStep® Mejorado / Intel Architecture-64 / Tecnología

Celeron 4xx

Extended Memory 64 / Tecnología de virtualización

(Vatio máximo: 95W)
FSB

533 / 800 / 1066 / 1333 MHz, FSB533 único soporte DDR2-533

Conjunto de

Intel G41

chips

Intel ICH7
Iniciativas de control de entorno,

ITE 8728F-BX

Le ofrece las funcionalidades heredadas de uso Monitor hardware
Súper E/S
más común Súper E/S.

Controlador/monitor de velocidad de ventilador

Interfaz de cuenta Low Pin

Función "Guardia inteligente" de ITE

Ranuras DIMM DDR2 x 2

Módulo de memoria DDR2 de canal Doble

Memoria

Cada DIMM admite DDR de 256MB / 512MB / Admite DDR2 de 533/ 800/1066(OC)

principal

1GB / 2GB / 4GB

DDR2-533 sólo para FSB1066 / 533

Capacidad máxima de memoria de 8GB

No admite DIMM registrados o DIMM compatibles con ECC

Gráficos

GMA X4500

Memoria máxima de vídeo compartida de 256MB

IDE

Controlador IDE integrado

Modo bus maestro Ultra DMA 33 / 66 / 100
Soporte los Modos PIO 0~4,
Tasas de transferencia de hasta 3.0 Gb/s.
SATA

Controlador ATA Serie Integrado
Compatible con la versión SATA 2.0.
Negociación de 10 / 100 Mb/s

Red Local

Realtek RTL 8105E
Funciones Half / Full dúplex

Soporte de

Soporte de sonido de Alta Definición
ALC662

sonido HD

Salida de sonido de 5.1 canales
Ranura PCI

Ranura PCI Express x16

Conector Puerto de impresora

Ranuras

Conectores

Cada conector soporta 1 Puerto de impresora

G41-M7
Especificación
en placa

Puerto serie

Conector IDE

Cada conector soporta 2 dispositivos IDE

Conector SATA

Cada conector soporta 1 dispositivos SATA

Conector de panel frontal

Soporta instalaciones en el panel frontal

Conector de sonido frontal

Soporta funciones de sonido en el panel frontal

Cabecera de ventilador de CPU

Fuente de alimentación de ventilador de CPU (con función
Smart Fan)

Cabecera de ventilador de sistema

Cabecera de borrado de CMOS

Conector USB

Conector de alimentación

Fuente de alimentación de ventilador de sistema

Cada conector soporta 2 puertos USB frontales

(24 patillas)
Conector de alimentación

(4 patillas)
Teclado PS/2

Ratón PS/2

Panel trasero Puerto VGA

de E/S

Puerto de red local

Puerto USB

Conector de sonido

Tamaño de la
182 mm. (A) X 235 Mm. (H)
placa
Soporte de
Biostar se reserva el derecho de añadir o retirar el soporte de
sistema

Windows 2000 / XP / Vista / 7 / 8
cualquier SO con o sin aviso previo.

operativo

Motherboard Manual

Portuguese
ESPECIFICAÇÕES
LGA 775
Suporta as tecnologias Hyper-Threading / Execute Disable Bit /
Processador Intel Core2Duo / Core2Quad /
CPU

Enhanced Intel SpeedStep® / Intel Arquitecture -64 / Extended
Pentium Dual-Core / Celeron Dual-Core /
Memory 64 / Virtualization
Celeron 4xx (Watt máximo: 95W)

FSB

533 / 800 / 1066 / 1333 MHz, FSB533 apoio apenas DDR2-533

Chipset

Intel G41 + Intel ICH7
ITE 8728F-BX

Iniciativas para controlo do ambiente

Especificação Proporciona as funcionalidades mais utilizadas

Monitorização do hardware

Super I/O

em termos da especificação Super I/O.

Controlador/Monitor da velocidade da ventoinha

Interface LPC (Low Pin Count).

Função "Smart Guardian" da ITE
Módulo de memória DDR2 de canal duplo

Ranhuras DIMM DDR2 x 2
Suporta módulos DDR2 533/ 800/1066(OC)
Memória

Cada módulo DIMM suporta uma memória

principal

DDR2 de 256 MB / 512 MB / 1GB / 2GB / 4GB

DDR2-533 apenas para FSB1066 / 533
Os módulos DIMM registados e os DIMM ECC não são
Capacidade máxima de memória:8 GB
suportados
Placa gráfica GMA X4500

Memória de vídeo máxima partilhada: 256 MB
Modo Bus master Ultra DMA 33 / 66 / 100

IDE

Controlador IDE integrado
Suporta o modo PIO 0~4,
Velocidades de transmissão de dados até 3.0 Gb/s.

SATA

Controlador Serial ATA integrado
Compatibilidade com a especificação SATA versão 2.0.
Auto negociação de 10 / 100 Mb/s

LAN

Realtek RTL 8105E
Capacidade semi/full-duplex

Suporte para
Suporta a especificação High-Definition Audio
áudio de alta ALC662
Saída de áudio de 5.1 canais
definição
Ranhura PCI

Ranhura PCI Express x16

Conector da para impressora

Ranhuras

Cada conector suporta 1 Porta para impressora

G41-M7
ESPECIFICAÇÕES
Porta série

Conectores

Conector IDE

Cada conector suporta 2 dispositivos IDE

na placa

Conector SATA

Cada conector suporta 1 dispositivo SATA

Conector do painel frontal

Para suporte de várias funções no painel frontal

Conector de áudio frontal

Suporta a função de áudio no painel frontal

Conector da ventoinha da CPU

Alimentação da ventoinha da CPU (com a função Smart Fan)

Conector da ventoinha do sistema

Alimentação da ventoinha do sistema

Conector para limpeza do CMOS

Conector USB

Conector de alimentação

Cada conector suporta 2 portas USB no painel frontal

(24 pinos)
Conector de alimentação

(4 pinos)
Teclado PS/2

Rato PS/2

Porta VGA

Porta LAN

Porta USB

Tomada de áudio

Entradas/Saí
das no painel
traseiro

Tamanho da
182 mm (L) X 235 mm (A)
placa
Sistemas
A Biostar reserva-se o direito de adicionar ou remover suporte
operativos

Windows 2000 / XP / Vista / 7 / 8
para qualquer sistema operativo com ou sem aviso prévio.

suportados

Motherboard Manual

Polish
SPEC
LGA 775

Procesor

Procesor Intel Core2Duo / Core2Quad /

Obsługa Hyper-Threading / Execute Disable Bit / Enhanced

Pentium Dual-Core / Celeron Dual-Core /

Intel SpeedStep® / Intel Architecture-64 / Extended Memory 64

Celeron 4xx

Technology / Virtualization Technology

(Maksymalny Watt: 95W)
FSB

533 / 800 / 1066 / 1333 MHz, FSB 533 obsługują tylko DDR2-533
Intel G41

Chipset
Intel ICH7
Moduł pamięci DDR2 z trybem podwójnego kanału

Gniazda DDR2 DIMM x 2
Pamięć

Każde gniazdo DIMM obsługuje moduły 256MB Obsługa DDR2 533/ 800/1066(OC)

główna

/ 512MB / 1GB / 2GB / 4GB

DDR2-533 tylko dla FSB1066 / 533

Maks. wielkość pamięci 8GB

Brak obsługi Registered DIMM oraz ECC DIMM

GMA X4500

Maks. wielkość współdzielonej pamięci video wynosi 256MB

ITE 8728F-BX

Funkcje kontroli warunków pracy,

Zapewnia najbardziej powszechne funkcje

Monitor H/W

Super I/O.

Kontroler/Monitor prędkości wentylatora

Interfejs Low Pin Count

Funkcja ITE "Smart Guardian"

Grafika

Super I/O

Ultra DMA 33 / 66 / 100 Tryb Bus Master
IDE

Zintegrowany kontroler IDE
obsługa PIO tryb 0~4,
Transfer danych do 3.0 Gb/s.

SATA

Zintegrowany kontroler Serial ATA
Zgodność ze specyfikacją SATA w wersji 2.0.
10 / 100 Mb/s z automatyczną negocjacją szybkości

LAN

Realtek RTL 8105E
Działanie w trybie połowicznego / pełnego dupleksu

Obsługa

Obsługa High-Definition Audio
ALC662

audio HD

5.1 kanałowe wyjście audio
Gniazdo PCI

Gniazdo PCI Express x16

Złącze Port drukarki

Gniazda

Każde złącze obsługuje 1 Port drukarki

G41-M7
SPEC
Złącza

Port szeregowy

wbudowane Złącze IDE

x1
x1

Każde złącze obsługuje 2 urządzenia IDE

Złącze SATA

Każde złącze obsługuje 1 urządzenie SATA

Złącze panela przedniego

Obsługa elementów panela przedniego

Przednie złącze audio

Obsługa funkcji audio na panelu przednim

Złącze główkowe wentylatora
Zasilanie wentylatora procesora (z funkcją Smart Fan)
procesora

Złącze główkowe wentylatora
Zasilanie wentylatora systemowego
systemowego

Złącze główkowe kasowania CMOS

Złącze USB

Złącze zasilania (24 pinowe)

Złącze zasilania (4 pinowe)

Klawiatura PS/2

Mysz PS/2

Back Panel

Port VGA

I/O

Port LAN

Port USB

Gniazdo audio

Każde złącze obsługuje 2 porty USB na panelu przednim

Wymiary
182 mm (S) X 235 mm (W)
płyty
Obsluga
Biostar zastrzega sobie prawo dodawania lub odwoływania
systemu

Windows 2000 / XP / Vista / 7 / 8
obsługi dowolnego systemu operacyjnego bez powiadomienia.

operacyjnego

Motherboard Manual

Russian
СПЕЦ
CPU
(центральны
й процессор)

LGA 775

Поддержка технологий Hyper-Threading / Execute Disable

Процессор Intel Core2Duo / Core2Quad

Bit / Enhanced Intel SpeedStep® / Intel Architecture-64 /

Pentium Dual-Core / Celeron Dual-Core /

Extended Memory 64 Technology / технологии

Celeron 4xx (Максимальный ватт: 95W)

виртуализация

FSB

533 / 800 / 1066 / 1333 МГц , FSB533 поддерживают только DDR2-533

Набор

Intel G41

микросхем

Intel ICH7
Модуль памяти с двухканальным режимом DDR2

Слоты DDR2 DIMM x 2
Основная

Каждый модуль DIMM поддерживает 256 МБ

память

/ 512МБ / 1ГБ / 2ГБ / 4ГБ DDR2

ECC DIMM
Максимальная совместно используемая видео память

GMA X4500

составляет 256 МБ

ITE 8728F-BX

Инициативы по охране окружающей среды,

Обеспечивает наиболее используемые
Super I/O

действующие функциональные возможности
Super I/O.
Интерфейс с низким количеством выводов

IDE

SATA
Локальная
сеть

DDR2-533 только для FSB1066 / 533
Не поддерживает зарегистрированные модули DIMM and

Максимальная ёмкость памяти 8ГБ

Графика

Поддержка DDR2 533/ 800/1066(OC)

Аппаратный монитор
Регулятор скорости вентилятора/ монитор
Функция ITE "Smart Guardian" (Интеллектуальная защита)

Встроенное устройство управления

Режим "хозяина" шины Ultra DMA 33 / 66 / 100

встроенными интерфейсами устройств

Поддержка режима PIO 0~4,

Встроенное последовательное устройство

скорость передачи данных до 3.0 гигабит/с.

управления ATA

Соответствие спецификации SATA версия 2.0.
Автоматическое согласование 10 / 100 Мб/с

Realtek RTL 8105E

Частичная / полная дуплексная способность

Звуковая
поддержка
жесткого

Звуковая поддержка High-Definition

ALC662

5.1канальный звуковой выход

диска
Слоты

Слот PCI

Слот PCI Express x16

Встроенный Разъём Порт подключения
разъём

Каждый разъём поддерживает 1 Порт подключения

принтера

Последовательный порт

принтера

G41-M7
СПЕЦ
Каждый разъём поддерживает 2 встроенных интерфейса

Разъём IDE

Разъём SATA

Каждый разъём поддерживает 1 устройство SATA

Разъём на лицевой панели

Поддержка устройств на лицевой панели

Входной звуковой разъём

Поддержка звуковых функций на лицевой панели

накопителей

Контактирующее приспособление

Источник питания для вентилятора центрального

вентилятора центрального процессора x1

процессора (с функцией интеллектуального вентилятора)

Контактирующее приспособление
вентилятора системы

Источник питания для вентилятора системы

Открытое контактирующее
приспособление CMOS

USB-разъём

Разъем питания (24 вывод)

Разъем питания (4 вывод)

Клавиатура PS/2

Задняя

Мышь PS/2

панель

Порт VGA

средств

Порт LAN

ввода-вывод USB-порт

панели
Поддержка
OS

панели

Гнездо для подключения
наушников

Размер

Каждый разъём поддерживает 2 USB-порта на лицевой

182 мм (Ш) X 235 мм (В)
Biostar сохраняет за собой право добавлять или удалять
Windows 2000 / XP / Vista / 7 / 8

средства обеспечения для OS с или без предварительного
уведомления.

‫‪Motherboard Manual‬‬

‫‪Arabic‬‬
‫اﻟﻤﻮاﺻﻔﺎت‬
‫‪LGA 775‬‬
‫ﻡﻌﺎﻟﺠﺎت ‪Intel Core2Duo / Core2Quad / Pentium‬‬

‫ﺗﺪﻋﻢ ﺗﻘﻨﻴﺎت ‪Hyper-Threading / Execute Disable Bit / Enhanced‬‬

‫وﺣﺪة اﻟﻤﻌﺎﻟﺠﺔ‬
‫‪ Dual-Core / Celeron Dual-Core / Celeron 4xx‬ﺑﺘﺮدد ‪Intel SpeedStep® / Intel Architecture-64 / Extended Memory‬‬
‫اﻟﻤﺮآﺰیﺔ‬
‫‪64 Technology / Virtualization Technology‬‬

‫یﺼﻞ إﻟﻰ‬
‫(واط ﻗﺼﻮى‪: 95‬و)‬

‫اﻟﻨﺎﻗﻞ اﻷﻡﺎﻡﻲ اﻟﺠﺎﻥﺒﻲ ﺗﺮدد ‪ 533 / 800 / 1066 / 1333‬ﻡﻴﺠﺎ هﺮﺗﺰ‪ FSB533 ,‬اﻟﺪﻋﻢ ﻓﻘﻂ ‪DDR2-533‬‬
‫‪Intel G41‬‬
‫ﻡﺠﻤﻮﻋﺔ اﻟﺸﺮاﺋﺢ‬
‫‪Intel ICH7‬‬
‫ﻓﺘﺤﺔ ‪DDR2 DIMM‬‬

‫ﻋﺪد‪2‬‬

‫وﺣﺪة ذاآﺮة ‪ DDR2‬ﻡﺰدوﺝﺔ اﻟﻘﻨﺎة‬

‫ﺗﺪﻋﻢ آﻞ ﻓﺘﺤﺔ ‪ DIMM‬ﺗﺪﻋﻢ ذاآﺮة ﻡﻦ ﻥﻮع ‪ DDR2‬ﺳﻌﺔ‬

‫ﺗﺪﻋﻢ اﻟﺬاآﺮة ﻡﻦ ﻥﻮع ‪ DDR2‬ﺳﻌﺎت ‪ 533/ 800/1066(OC),‬ﻡﻴﺠﺎ ﺑﺎیﺖ‬

‫‪ 512/256‬ﻡﻴﺠﺎ ﺑﺎیﺖ و‪ 1‬ﺝﻴﺠﺎ ﺑﺎیﺖ و‪ 2‬ﺝﻴﺠﺎ ﺑﺎیﺖ و‪ 4‬ﺝﻴﺠﺎ ﺑﺎیﺖ‬

‫‪ DDR2-533‬ﻓﻘﻂ ﻡﻦ أﺝﻞ ‪FSB1066 / 533‬‬

‫ﺳﻌﺔ ذاآﺮة ﻗﺼﻮى ‪ 8‬ﺝﻴﺠﺎ ﺑﺎیﺖ‬

‫ﻻ ﺗﺪﻋﻢ رﻗﺎﺋﻖ اﻟﺬاآﺮة ‪ DIMM‬وﺗﻠﻚ اﻟﺘﻲ ﻻ ﺗﺘﻮاﻓﻖ ﻡﻊ ‪ECC‬‬

‫‪GMA X4500‬‬

‫أﻗﺼﻰ ﺳﻌﺔ ﻟﺬاآﺮة اﻟﻔﻴﺪیﻮ اﻟﻤﺸﺘﺮآﺔ ‪ 256‬ﻡﻴﺠﺎ ﺑﺎیﺖ‬

‫اﻟﺬاآﺮة اﻟﺮﺋﻴﺴﻴﺔ‬

‫ﺑﻄﺎﻗﺔ اﻟﺮﺳﻮﻡﺎت‬

‫وﺳﺎﺋﻞ اﻟﺘﺤﻜﻢ ﻓﻲ اﻟﺒﻴﺌﺔ‪:‬‬
‫‪ITE 8728F-BX‬‬
‫ﻡﺮاﻗﺐ ﻟﻤﻌﺮﻓﺔ ﺣﺎﻟﺔ اﻷﺝﻬﺰة‬
‫‪Super I/O‬‬

‫ﺗﻮﻓﺮ وﻇﻴﻔﺔ ‪ Super I/O‬اﻷآﺜﺮ اﺳﺘﺨﺪاﻡﺎً‪.‬‬
‫ﻡﺮاﻗﺐ ﻓﻲ ﺳﺮﻋﺔ اﻟﻤﺮوﺣﺔ‬
‫ﺗﺪﻋﻢ ﺗﻘﻨﻴﺔ ‪Low Pin Count Interface‬‬
‫وﻇﻴﻔﺔ "‪ "Smart Guardian‬ﻡﻦ ‪ITE‬‬
‫ﻥﺎﻗﻞ ﺑﺘﻘﻨﻴﺔ ‪Ultra DMA 33 / 66 / 100‬وﺿﻊ رﺋﻴﺴﻲ‬

‫ﻡﻨﻔﺬ ‪IDE‬‬

‫ﻡﺘﺤﻜﻢ ‪ IDE‬ﻡﺘﻜﺎﻡﻞ‬

‫‪SATA‬‬

‫ﻡﺘﺤﻜﻢ ‪ Serial ATA‬ﻡﺘﻜﺎﻡﻞ‬

‫ﺵﺒﻜﺔ داﺥﻠﻴﺔ‬

‫‪Realtek RTL 8105E‬‬

‫دﻋﻢ وﺿﻊ ‪PIO Mode 0~4‬‬
‫ﻥﻘﻞ اﻟﺒﻴﺎﻥﺎت ﺑﺴﺮﻋﺎت ﺗﺼﻞ إﻟﻰ ‪ 3.0‬ﺝﻴﺠﺎﺑﺖ‪/‬ﺙﺎﻥﻴﺔ‪.‬‬
‫ﻡﻄﺎﺑﻘﺔ ﻟﻤﻮاﺻﻔﺎت ‪ SATA‬اﻹﺻﺪار ‪. 2.0‬‬
‫ﺗﻔﺎوض ﺗﻠﻘﺎﺋﻲ ‪ 100/10‬ﻡﻴﺠﺎ ﺑﺎیﺖ ‪ /‬ﺙﺎﻥﻴﺔ‬
‫إﻡﻜﺎﻥﻴﺔ اﻟﻨﻘﻞ اﻟﻤﺰدوج اﻟﻜﺎﻡﻞ‪/‬اﻟﻨﺼﻔﻲ‬
‫ﺗﺪﻋﻢ ﺗﻘﻨﻴﺔ اﻟﺼﻮت ﻋﺎﻟﻲ اﻟﺘﻌﺮیﻒ ﻡﻦ‬

‫دﻋﻢ اﻟﺼﻮت ﻋﺎﻟﻲ‬
‫‪ALC662‬‬

‫‪ 5.1‬ﻗﻨﻮات ﻟﺨﺮج اﻟﺼﻮت‬

‫اﻟﺘﻌﺮیﻒ‬
‫ﻓﺘﺤﺔ ‪PCI‬‬

‫ﻋﺪد ‪2‬‬

‫ﻓﺘﺤﺔ ‪PCI Express x16‬‬

‫ﻋﺪد ‪1‬‬

‫ﻡﻨﻔﺬ ﻃﺎﺑﻌﺔ‬

‫ﻋﺪد ‪1‬‬

‫اﻟﻔﺘﺤﺎت‬

‫اﻟﻤﻨﺎﻓﺬ ﻋﻠﻰ ﺳﻄﺢ‬

‫‪46‬‬

‫‪G41-M7‬‬
‫اﻟﻤﻮاﺻﻔﺎت‬
‫اﻟﻠﻮﺣﺔ‬

‫ﻡﻨﻔﺬ ﺗﺴﻠﺴﻠﻲ‬

‫ﻋﺪد‪1‬‬

‫ﻡﻨﻔﺬ ‪IDE‬‬

‫ﻋﺪد ‪1‬‬

‫یﺪﻋﻢ آﻞ ﻡﻨﻔﺬ اﺙﻨﻴﻦ ﻡﻦ أﺝﻬﺰة ‪IDE‬‬

‫ﻡﻨﻔﺬ ‪SATA‬‬

‫ﻋﺪد ‪4‬‬

‫یﺪﻋﻢ آﻞ ﻡﻨﻔﺬ واﺣﺪ ﻡﻦ أﺝﻬﺰة ‪SATA‬‬

‫ﻡﻨﻔﺬ اﻟﻠﻮﺣﺔ اﻷﻡﺎﻡﻴﺔ‬

‫ﻋﺪد ‪1‬‬

‫یﺪﻋﻢ ﺗﺠﻬﻴﺰات اﻟﻠﻮﺣﺔ اﻷﻡﺎﻡﻴﺔ‬

‫ﻡﻨﻔﺬ اﻟﺼﻮت اﻷﻡﺎﻡﻲ‬

‫ﻋﺪد ‪1‬‬

‫یﺪﻋﻢ وﻇﻴﻔﺔ اﻟﺼﻮت ﺑﺎﻟﻠﻮﺣﺔ اﻷﻡﺎﻡﻴﺔ‬

‫وﺻﻠﺔ ﻡﺮوﺣﺔ وﺣﺪة اﻟﻤﻌﺎﻟﺠﺔ اﻟﻤﺮآﺰیﺔ‬

‫ﻋﺪد ‪1‬‬

‫ﻟﺘﻮﺻﻴﻞ اﻟﻄﺎﻗﺔ ﻟﻤﺮوﺣﺔ وﺣﺪة اﻟﻤﻌﺎﻟﺠﺔ ﻡﻊ وﻇﻴﻔﺔ ‪Smart Fan‬‬

‫وﺻﻠﺔ ﻡﺮوﺣﺔ اﻟﻨﻈﺎم‬

‫ﻋﺪد ‪1‬‬

‫ﻟﺘﻮﺻﻴﻞ اﻟﻄﺎﻗﺔ ﻟﻤﺮوﺣﺔ اﻟﻨﻈﺎم‬

‫وﺻﻠﺔ ﻡﺴﺢ ‪CMOS‬‬

‫ﻋﺪد ‪1‬‬

‫ﻡﻨﻔﺬ ‪USB‬‬

‫ﻋﺪد ‪2‬‬

‫ﻡﻨﻔﺬ ﺗﻮﺻﻴﻞ اﻟﻄﺎﻗﺔ )‪24‬دﺑﻮس(‬

‫ﻋﺪد ‪1‬‬

‫ﻡﻨﻔﺬ ﺗﻮﺻﻴﻞ اﻟﻄﺎﻗﺔ )‪4‬دﺑﺎﺑﻴﺲ(‬

‫ﻋﺪد ‪1‬‬

‫ﻟﻮﺣﺔ ﻡﻔﺎﺗﻴﺢ ‪PS/2‬‬

‫ﻋﺪد ‪1‬‬

‫ﻡﺎوس ‪PS/2‬‬

‫ﻋﺪد ‪1‬‬

‫ﻡﻨﺎﻓﺬ دﺥﻞ‪/‬ﺥﺮج‬

‫ﻡﻨﻔﺬ ‪VGA‬‬

‫ﻋﺪد ‪1‬‬

‫اﻟﻠﻮﺣﺔ اﻟﺨﻠﻔﻴﺔ‬

‫ﻡﻨﻔﺬ ﺵﺒﻜﺔ اﺗﺼﺎل ﻡﺤﻠﻴﺔ‬

‫ﻋﺪد ‪1‬‬

‫ﻡﻨﺎﻓﺬ ‪USB‬‬

‫ﻋﺪد ‪4‬‬

‫ﻡﻘﺒﺲ ﺻﻮت‬

‫ﻋﺪد ‪3‬‬

‫ﺣﺠﻢ اﻟﻠﻮﺣﺔ‬

‫‪ 182‬ﻡﻢ )ﻋﺮض( ‪ 235 X‬ﻡﻢ )ارﺗﻔﺎع(‬

‫دﻋﻢ أﻥﻈﻤﺔ اﻟﺘﺸﻐﻴﻞ‬

‫‪Windows 2000 / XP / Vista / 7 / 8‬‬

‫یﺪﻋﻢ آﻞ ﻡﻨﻔﺬ ﻓﺘﺤﺘﻲ ‪ USB‬ﺑﺎﻟﻠﻮﺣﺔ اﻷﻡﺎﻡﻴﺔ‬

‫ﺗﺤﺘﻔﻆ ‪ Biostar‬ﺑﺤﻘﻬﺎ ﻓﻲ إﺿﺎﻓﺔ أو إزاﻟﺔ اﻟﺪﻋﻢ ﻷي ﻥﻈﺎم ﺗﺸﻐﻴﻞ ﺑﺈﺥﻄﺎر أو ﺑﺪون‬
‫إﺥﻄﺎر‪.‬‬

‫‪47‬‬

Motherboard Manual

Japanese
仕様
LGA 775

CPU

Intel Core2Duo / Core2Quad /

Hyper-Threading / Execute Disable Bit / Enhanced Intel

Pentium Dual-Core / Celeron Dual-Core /

SpeedStep® / Intel Architecture-64 / Extended Memory 64

Celeron 4xx processor

Technology / Virtualization Technologyをサポートします

(最高のワット: 95W)
FSB

533 / 800 / 1066 / 1333 MHz, FSB533のみをサポートDDR2-533
Intel G41

チップセット
Intel ICH7
DDR2 DIMMスロット x 2

デュアル チャンネルモードDDR2メモリモジュール

各DIMMは 256MB / 512MB / 1GB / 2GB/ 4GB DDR2 533/ 800/1066(OC) をサポート
メインメモリ
DDR2をサポート

DDR2-533のみFSB1066/ 533用

最大メモリ容量8GB

登録済みDIMMとECC DIMMはサポートされません

GMA X4500

最大の共有ビデオメモリは256MBです

ITE 8728F-BX

環境コントロールイニシアチブ、

グラフィック
ス

もっとも一般に使用されるレガシーSuper I/O機 H/Wモニター
Super I/O
能を採用しています。

ファン速度コントローラ/ モニター

低ピンカウントインターフェイス

ITEの「スマートガーディアン」機能
Ultra DMA 33 / 66 / 100バスマスタモード

IDE

統合IDEコントローラ
PIO Mode 0~4のサポート、
最高3.0 Gb/秒のデータ転送速度

SATA

統合シリアルATAコントローラ
SATAバージョン2.0仕様に準拠。
10 / 100 Mb/秒のオートネゴシエーション

LAN

Realtek RTL 8105E
半/全二重機能

HDオーディ

ハイデフィニションオーディオのサポート
ALC662
5.1 チャンネルオーディオアウト

オのサポート
PCIスロット

PCI Express x16スロット

スロット

G41-M7
仕様
プリンタポートコネクタ

シリアルポート

IDEコネクタ

各コネクタは2つのIDEデバイスをサポートします

SATAコネクタ

各コネクタは1つのSATAデバイスをサポートします

フロントパネルコネクタ

フロントパネル機能をサポートします

フロントオーディオコネクタ

フロントパネルオーディオ機能をサポートします

CPUファンヘッダ

CPUファン電源装置(スマートファン機能を搭載)

システムファンヘッダ

システムファン電源装置

CMOSクリアヘッダ

USBコネクタ

各コネクタは1つのプリンタポートをサポートします

オンボードコ
ネクタ

各コネクタは2つのフロントパネルUSBポートをサポートしま
す
電源コネクタ(24ピン)

電源コネクタ(4ピン)

PS/2キーボード

PS/2マウス

背面パネル

VGAポート

I/O

LANポート

USBポート

オーディオジャック

ボードサイズ 182 mm (幅) X 235 mm (高さ)
Biostarは事前のサポートなしにOSサポートを追加または削除
OSサポート Windows 2000 / XP / Vista / 7 / 8
する権利を留保します。

2012/07/23

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
Page Count                      : 51
Creation Date                   : 2012:07:23 08:47:34Z
Mod Date                        : 2012:07:23 08:47:34Z
Producer                        : Acrobat Distiller 5.0 (Windows)
Author                          : 101001
Create Date                     : 2012:07:23 08:47:34Z
Modify Date                     : 2012:07:23 08:47:34Z
Metadata Date                   : 2012:07:23 08:47:34Z
Creator                         : 101001
Title                           : Microsoft Word - IG41A-M7S_v2_120723.doc

EXIF Metadata provided by EXIF.tools

Biostar G41 M7 V7 X Owners Manual IG41A M7S_v2_120723

Navigation menu

Versions of this User Manual:

Views

Navigation