Biostar N68S Plus Owners Manual N61PB M2S & N68SA M2S_100504
2014-07-31
: Biostar Biostar-N68S-Plus-Owners-Manual biostar-n68s-plus-owners-manual biostar pdf
Open the PDF directly: View PDF .
Page Count: 47
Download | |
Open PDF In Browser | View PDF |
MCP6P M2+/N68S+ Setup Manual FCC Information and Copyright This equipment has been tested and found to comply with the limits of a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. There is no guarantee that interference will not occur in a particular installation. The vendor makes no representations or warranties with respect to the contents here and specially disclaims any implied warranties of merchantability or fitness for any purpose. Further the vendor reserves the right to revise this publication and to make changes to the contents here without obligation to notify any party beforehand. Duplication of this publication, in part or in whole, is not allowed without first obtaining the vendor’s approval in writing. The content of this user’s manual is subject to be changed without notice and we will not be responsible for any mistakes found in this user’s manual. All the brand and product names are trademarks of their respective companies. Table of Contents Chapter 1: Introduction ............................................................ 1 1.1 Before You Start ................................................................................ 1 1.2 Package Checklist ............................................................................. 1 1.3 Motherboard Features...................................................................... 2 1.4 1.5 Rear Panel Connectors ..................................................................... 3 Motherboard Layout......................................................................... 4 Chapter 2: Hardware Installation ............................................. 5 2.1 Installing Central Processing Unit (CPU)....................................... 5 2.2 FAN Headers...................................................................................... 7 2.3 Installing System Memory ................................................................ 8 2.4 Connectors and Slots ....................................................................... 10 Chapter 3: Headers & Jumpers Setup ..................................... 12 3.1 How to Setup Jumpers .................................................................... 12 3.2 Detail Settings.................................................................................. 12 Chapter 4: RAID Functions ..................................................... 19 4.1 Operating System............................................................................ 19 4.2 Raid Arrays ...................................................................................... 19 4.3 How RAID Works............................................................................. 19 Chapter 5: Useful Help ............................................................ 23 5.1 Driver Installation Note.................................................................. 23 5.2 Award BIOS Beep Code .................................................................. 24 5.3 Extra Information............................................................................ 25 5.4 Troubleshooting............................................................................... 26 Appendix: SPEC In Other Languages ...................................... 27 German.................................................................................................................. 28 French .................................................................................................................... 30 Italian..................................................................................................................... 32 Spanish ................................................................................................................... 34 Portuguese ............................................................................................................ 36 Polish...................................................................................................................... 38 Russian ................................................................................................................... 40 Arabic..................................................................................................................... 42 Japanese ................................................................................................................ 44 MCP6P M2+/N68S+ CHAPTER 1: INTRODUCTION 1.1 BEFORE YOU START Thank you for choosing our product. Before you start installing the motherboard, please make sure you follow the instructions below: 1.2 Prepare a dry and stable working environment with sufficient lighting. Always disconnect the computer from power outlet before operation. Before you take the motherboard out from anti-static bag, ground yourself properly by touching any safely grounded appliance, or use grounded wrist strap to remove the static charge. Avoid touching the components on motherboard or the rear side of the board unless necessary. Hold the board on the edge, do not try to bend or flex the board. Do not leave any unfastened small parts inside the case after installation. Loose parts will cause short circuits which may damage the equipment. Keep the computer from dangerous area, such as heat source, humid air and water. PACKAGE CHECKLIST IDE Cable X 1(optional) Serial ATA Cable X 2 Rear I/O Panel for ATX Case X 1 Installation Guide X 1 Fully Setup Driver CD X 1 (full version manual files inside) FDD Cable X 1 (optional) Serial ATA Power Cable X 1 (optional) USB 2.0 Cable X1 (optional) S/PDIF out Cable X 1 (optional) Note: The package contents may differ by area or your motherboard version. 1 Motherboard Manual 1.3 MOTHERBOARD FEATURES SPEC Socket AM2+ CPU AMD Phenom / Phenom II / Athlon / AMD 64 Architecture enables 32 and 64 bit computing Athlon II / Sempron processors Supports Hyper Transport and Cool=n=Quiet (Maximum Watt: 95W) FSB Chipset Supports up to 1 GHz Bandwidth Support HyperTransport GeForce 6150 SE/nForce 430 (MCP6P M2+) GeForce 7025/nForce 630a (N68S+) Environment Control initiatives, ITE 8716F Super I/O Provides the most commonly used legacy H/W Monitor Super I/O functionality. Fan Speed Controller Low Pin Count Interface ITE's "Smart Guardian" function DDR2 DIMM Slots x 2 Dual Channel Mode DDR2 memory module Main Max Memory Capacity 8GB Memory Each DIMM supports 256MB/512MB/1GB/ 2GB/4GB DDR2 Graphics GeForce 7025/nForce 630a (N68S+) IDE Integrated IDE Controller SATA II Integrated Serial ATA Controller LAN Realtek RTL 8201CL Sound ALC662 Registered DIMM and ECC DIMM is not supported Max Shared Video Memory is 512MB (under OS) Ultra DMA 33 / 66 / 100 / 133 Bus Master Mode supports PIO Mode 0~4, Data transfer rates up to 3 Gb/s. SATA Version 2.0 specification compliant. 10 / 100 Mb/s auto negotiation Half / Full duplex capability 5.1 channels audio out High Definition Audio PCI Slot x2 Supports PCI expansion cards PCI Express x16 Slot x1 Supports PCI-E x16 expansion cards On Board Floppy Connector x1 Each connector supports 2 Floppy drives Connector Printer Port Connector x1 Each connector supports 1 Printer port IDE Connector x1 Each connector supports 2 IDE device SATA Connector x4 Each connector supports 1 SATA devices Front Panel Connector x1 Supports front panel facilities Slots 2 GeForce 6150 SE/nForce 430 (MCP6P M2+) Supports DDR2 533 / 667 / 800 / 1066 MCP6P M2+/N68S+ SPEC Back Panel I/O Board Size Special Features Front Audio Connector x1 Supports front panel audio function CD-in Connector x1 Supports CD audio-in function S/PDIF out Connector x1 Supports digital audio out function CPU Fan Header x1 CPU Fan power supply (with Smart Fan function) System Fan Header x1 System Fan Power supply CMOS clear Header x1 Restore CMOS data to factory default USB Connector x3 Each connector supports 2 front panel USB ports Power Connector (24pin) x1 Connects to Power supply Power Connector (4pin) x1 Connects to Power supply PS/2 Keyboard x1 Connects to PS/2 Keyboard PS/2 Mouse x1 Connects to PS/2 Mouse VGA port x1 Connect to D-SUB monitor Serial Port x1 Provide RS-232 Serial connection LAN port x1 Connect to RJ-45 ethernet cable USB Port x4 Connect to USB devices Audio Jack x3 Provide Audio-In/Out and microphone connection 190 mm(W) x 244 mm(L) RAID 0 / 1 / 0+1 / 5 support BIOSTAR Reserves the right to add or remove support OS Support Windows XP / Vista / 7 1.4 for any OS With or without notice. REAR PANEL CONNECTORS PS/2 Mouse LAN Line In/ Surround Line Out Mic In 1/ Bass/ Center PS/2 Keyboard COM1 VGA USBX2 USBX2 3 Motherboard Manual 1.5 MOTHERBOARD LAYOUT JKBMS1 JCFA N1 JATXPWR 4 JUS BPWR1 AM2+ DIMMB1 Socket JVGA1 DIMMA1 JCOM1 JKB _PWR JUSB1 JATXPWR 1 JU SBPWR2 JAUD IO1 GeForce 6150 SE/7025 nForce 430/630a JCDIN1 IDE1 JU SBLAN1 JUS B3 JAU DIOF1 JUS B2 JUS B4 L AN PCI-EX16 BIOS JCMOS1 BAT1 PCI2 Codec JSPD IF_ OUT1 Super I/O PCI1 S ATA4 S ATA1 S ATA3 JSFAN1 JPR NT1 FDD1 Note: ■ represents the 1st pin. 4 S ATA2 JPANEL 1 MCP6P M2+/N68S+ CHAPTER 2: HARDWARE INSTALLATION 2.1 INSTALLING CENTRAL PROCESSING UNIT (CPU) Step 1: Remove the socket protection cap. Step 2: Pull the lever toward direction A from the socket and then raise the lever up to a 90-degree angle. Step 3: Look for the white triangle on socket, and the gold triangle on CPU should point towards this white triangle. The CPU will fit only in the correct orientation. 5 Motherboard Manual Step 4: Hold the CPU down firmly, and then close the lever toward direct B to complete the installation. Step 5: Put the CPU Fan on the CPU and buckle it. Connect the CPU FAN power cable to the JCFAN1. This completes the installation. Note: Please update the BIOS to the latest version while using AM2+ CPUs. Due to the latest CPU transition, you may encounter the situation that the new system failed to boot while using new AM2+ CPUs. In this case, please install one standard AM2 CPU to boot your system, and update the latest BIOS from our website for AM2+ CPUs support. 6 MCP6P M2+/N68S+ 2.2 FAN HEADERS These fan headers support cooling-fans built in the computer. The fan cable and connector may be different according to the fan manufacturer. Connect the fan cable to the connector while matching the black wire to pin#1. JCFAN1: CPU Fan Header 1 4 Pin Assignment Ground +12V FAN RPM rate sense Smart Fan Control (By Fan) 1 2 3 4 JSFAN1: System Fan Header Pin 1 2 3 1 Assignment Ground +12V FAN RPM rate sense 3 Note: The JCFAN1 supports 4-pin head connector. The JSFAN1 supports 3-pin head connector. When connecting with wires onto connectors, please note that the red wire is the positive and should be connected to pin#2, and the black wire is Ground and should be connected to GND. 7 Motherboard Manual 2.3 INSTALLING SYSTEM MEMORY DIMMA1 DIMMB1 A. Memory Modules 8 1. Unlock a DIMM slot by pressing the retaining clips outward. Align a DIMM on the slot such that the notch on the DIMM matches the break on the Slot. 2. Insert the DIMM vertically and firmly into the slot until the retaining chip snap back in place and the DIMM is properly seated. MCP6P M2+/N68S+ B. Memory Capacity DIMM Socket Location DDR2 Module Total Memory Size DIMMA1 256MB/512MB/1GB/2GB/4GB DIMMB1 256MB/512MB/1GB/2GB/4GB Max is 8GB. C. Dual Channel Memory installation To trigger the Dual Channel function of the motherboard, the memory module must meet the following requirements: Install memory module of the same density in pair, shown in the following table. DIMMA1 Dual Channel Status DIMMB1 Disabled O X Disabled X O Enabled O O (O means memory installed, X means memory not installed.) The DRAM bus width of the memory module must be the same (x8 or x16) 9 Motherboard Manual 2.4 CONNECTORS AND SLOTS FDD1: Floppy Disk Connector The motherboard provides a standard floppy disk connector that supports 360K, 720K, 1.2M, 1.44M and 2.88M floppy disk types. This connector supports the provided floppy drive ribbon cables. 2 34 1 33 IDE1: IDE/ATAPI Connector The motherboard has a 32-bit Enhanced PCI IDE Controller that provides PIO Mode 0~4, Bus Master, and Ultra DMA 33/66/100/133 functionality. The IDE connector can connect a master and a slave drive, so you can connect up to two drives. 10 40 39 2 1 MCP6P M2+/N68S+ PCI-EX16: PCI-Express x16 Slot - PCI-Express 1.0a compliant. Maximum theoretical realized bandwidth of 4GB/s simultaneously per direction, for an aggregate of 8GB/s totally. PCI-Express supports a raw bit-rate of 2.5GB/s on the data pins. 2X bandwidth over the traditional PCI architecture. PCI-EX16 PCI1~PCI2: Peripheral Component Interconnect Slots This motherboard is equipped with 2 standard PCI slots. PCI stands for Peripheral Component Interconnect, and it is a bus standard for expansion cards. This PCI slot is designated as 32 bits. PCI1 PCI2 11 Motherboard Manual CHAPTER 3: HEADERS & JUMPERS SETUP 3.1 HOW TO SETUP JUMPERS The illustration shows how to set up jumpers. When the jumper cap is placed on pins, the jumper is “close”, if not, that means the jumper is “open”. Pin opened 3.2 Pin closed Pin1-2 closed DETAIL SETTINGS JPANEL1: Front Panel Header This 16-pin connector includes Power-on, Reset, HDD LED, Power LED, and speaker connection. It allows user to connect the PC case’s front panel switch functions. PWR_LED On/Off ++ - 9 1 SPK Pin 1 2 3 4 5 6 7 8 12 Assignment +5V N/A N/A Speaker HDD LED (+) HDD LED (-) Ground Reset control Function Speaker Connector Hard drive LED Reset button 16 8 + - Pin 9 10 11 12 13 14 15 16 RST HLED Assignment N/A N/A N/A Power LED (+) Power LED (+) Power LED (-) Power button Ground Function N/A N/A Power LED Power-on button MCP6P M2+/N68S+ JATXPWR1: ATX Power Source Connector This connector allows user to connect 24-pin power connector on the ATX power supply. Pin 13 14 15 16 17 18 19 20 21 22 23 24 Assignment +3.3V -12V Ground PS_ON Ground Ground Ground NC +5V +5V +5V Ground Pin 1 2 3 4 5 6 7 8 9 10 11 12 13 1 24 12 Assignment +3.3V +3.3V Ground +5V Ground +5V Ground PW_OK Standby Voltage+5V +12V +12V +3.3V JATXPWR4: ATX Power Source Connector By connecting this connector, it will provide +12V to CPU power circuit. 1 4 2 3 Pin 1 2 3 4 Assignment +12V +12V Ground Ground Note: Before power on the system, please make sure that both JATXPWR1 and JATXPWR4 connectors have been plugged-in. 13 Motherboard Manual JUSB2/JUSB3/JUSB4: Headers for USB 2.0 Ports at Front Panel This header allows user to connect additional USB cable on the PC front panel, and also can be connected with internal USB devices, like USB card reader. Pin 1 2 3 4 5 6 7 8 9 10 JUSB3 JUSB2 JUSB4 2 10 1 9 Assignment +5V (fused) +5V (fused) USBUSBUSB+ USB+ Ground Ground Key NC SATA1~SATA4: Serial ATA Connectors The motherboard has a PCI to SATA Controller with 4 channels SATA interface. SATA2 SATA4 SATA1 SATA3 1 14 4 7 Pin 1 2 3 4 5 6 7 Assignment Ground TX+ TXGround RXRX+ Ground MCP6P M2+/N68S+ JAUDIOF1: Front Panel Audio Header This header allows user to connect the front audio output cable with the PC front panel. This header allows only HD audio front panel connector; AC’97 connector is not acceptable. 10 9 2 1 Pin 1 2 3 4 5 6 7 8 9 10 Assignment Mic Left in Ground Mic Right in GPIO Right line in Jack Sense Front Sense Key Left line in Jack Sense JCDIN1: CD-ROM Audio-in Connector This connector allows user to connect the audio source from the variaty devices, like CD-ROM, DVD-ROM, PCI sound card, PCI TV turner card etc.. Pin 1 1 4 2 3 4 Assignment Left Channel Input Ground Ground Right Channel Input 15 Motherboard Manual JSPDIF_OUT1: Digital Audio-out Connector This connector allows user to connect the PCI bracket SPDIF output header. Pin 1 2 3 1 Assignment +5V SPDIF_OUT Ground 3 JCMOS1: Clear CMOS Header By placing the jumper on pin2-3, it allows user to restore the BIOS safe setting and the CMOS data, please carefully follow the procedures to avoid damaging the motherboard. 1 3 Pin 1-2 Close: Normal Operation (default). 1 1 3 3 Pin 2-3 Close: Clear CMOS data. ※ Clear CMOS Procedures: 1. 2. 3. 4. 5. 6. 16 Remove AC power line. Set the jumper to “Pin 2-3 close”. Wait for five seconds. Set the jumper to “Pin 1-2 close”. Power on the AC. Reset your desired password or clear the CMOS data. MCP6P M2+/N68S+ JPRNT1: Printer Port Connector This header allows you to connector printer on the PC. 2 1 Pin 1 2 3 4 5 6 7 8 9 10 11 12 13 Assignment -Strobe -ALF Data 0 -Error Data 1 -Init Data 2 -Scltin Data 3 Ground Data 4 Ground Data 5 25 Pin 14 15 16 17 18 19 20 21 22 23 24 25 26 Assignment Ground Data 6 Ground Data 7 Ground -ACK Ground Busy Ground PE Ground SCLT Key 17 Motherboard Manual JUSBPWR1/JUSBPWR2: Power Source Headers for USB Ports Pin 1-2 Close: JUSBPWR1: +5V for USB ports at JUSB1/JUSBLAN1. JUSBPWR2: +5V for USB ports at front panel (JUSB2/JUSB3/JUSB4). Pin 2-3 Close: JUSBPWR1: +5V STB for USB ports at JUSB1/JUSBLAN1. JUSBPWR2: +5V STB for USB ports at front panel (JUSB2/JUSB3/JUSB4). JUSBPWR1 3 1 3 1 Pin 1-2 close 3 1 JUSBPWR2 3 1 Pin 2-3 close JKB_PWR: Power Source Header for PS/2 Keyboard and Mouse 3 1 3 1 Pin 1-2 close +5V for PS/2 keyboard and mouse. 3 1 Pin 2-3 close +5V STB for PS/2 keyboard and mouse. 18 MCP6P M2+/N68S+ CHAPTER 4: RAID FUNCTIONS 4.1 OPERATING SYSTEM Supports Windows XP and Windows Vista. 4.2 RAID ARRAYS RAID supports the following types of RAID arrays: RAID 0: RAID 0 defines a disk striping scheme that improves disk read and write times for many applications. RAID 1: RAID 1 defines techniques for mirroring data. RAID 0+1: RAID 0+1 combines the techniques used in RAID 0 and RAID 1. RAID 5: RAID 5 provides fault tolerance and better utilization of disk capacity. 4.3 HOW RAID WORKS RAID 0: The controller “stripes” data across multiple drives in a RAID 0 array system. It breaks up a large file into smaller blocks and performs disk reads and writes across multiple drives in parallel. The size of each block is determined by the stripe size parameter, which you set during the creation of the RAID set based on the system environment. This technique reduces overall disk access time and offers high bandwidth. Features and Benefits Drives: Minimum 2, and maximum is up to 6 or 8. Depending on the platform. Uses: Intended for non-critical data requiring high data throughput, or any environment that does not require fault tolerance. Benefits: provides increased data throughput, especially for large files. No capacity loss penalty for parity. Drawbacks: Does not deliver any fault tolerance. If any drive in the array fails, all data is lost. Fault Tolerance: No. Block 1 Block 3 Block 5 Block 2 Block 4 Block 6 19 Motherboard Manual RAID 1: Every read and write is actually carried out in parallel across 2 disk drives in a RAID 1 array system. The mirrored (backup) copy of the data can reside on the same disk or on a second redundant drive in the array. RAID 1 provides a hot-standby copy of data if the active volume or drive is corrupted or becomes unavailable because of a hardware failure. RAID techniques can be applied for high-availability solutions, or as a form of automatic backup that eliminates tedious manual backups to more expensive and less reliable media. Features and Benefits Drives: Minimum 2, and maximum is 2. Uses: RAID 1 is ideal for small databases or any other application that requires fault tolerance and minimal capacity. Benefits: Provides 100% data redundancy. Should one drive fail, the controller switches to the other drive. Drawbacks: Requires 2 drives for the storage space of one drive. Performance is impaired during drive rebuilds. Fault Tolerance: Yes. Block 1 Block 2 Block 3 20 Block 1 Block 2 Block 3 MCP6P M2+/N68S+ RAID 0+1: RAID 0 drives can be mirrored using RAID 1 techniques. Resulting in a RAID 0+1 solution for improved performance plus resiliency. Features and Benefits Drives: Minimum 4, and maximum is 6 or 8, depending on the platform. Benefits: Optimizes for both fault tolerance and performance, allowing for automatic redundancy. May be simultaneously used with other RAID levels in an array, and allows for spare disks. Drawbacks: Requires twice the available disk space for data redundancy, the same as RAID level 1. Fault Tolerance: Yes. GeForce 6150 SE / 7025 nForce 430 / 630a Block 1 Block 3 Block 5 Block 2 Block 4 Block 6 Block 1 Block 3 Block 5 Block 2 Block 4 Block 6 21 Motherboard Manual RAID 5: RAID 5 stripes both data and parity information across three or more drives. It writes data and parity blocks across all the drives in the array. Fault tolerance is maintained by ensuring that the parity information for any given block of data is placed on a different drive from those used to store the data itself. Features and Benefits Drives: Minimum 3. Uses: RAID 5 is recommended for transaction processing and general purpose service. Benefits: An ideal combination of good performance, good fault tolerance, and high capacity and storage efficiency. Drawbacks: Individual block data transfer rate same as a single disk. Write performance can be CPU intensive. Fault Tolerance: Yes. Disk 1 DATA 1 DATA 3 PARITY DATA 7 DATA 9 PARITY Disk 2 GeF orce 6150 SE / 7025 nForce 430 / 630a DATA 2 PARITY DATA 5 DATA 8 PARITY DATA 11 Disk 3 PARITY DATA 4 DATA 6 PARITY DATA 10 DATA 12 ※ 22 For more detailed setup information, please refer to the Driver CD, or go to http://www.nvidia.com/object/IO_28159.html to download the NVIDIA RAID User’s Guide. MCP6P M2+/N68S+ CHAPTER 5: USEFUL HELP 5.1 DRIVER INSTALLATION NOTE After you installed your operating system, please insert the Fully Setup Driver CD into your optical drive and install the driver for better system performance. You will see the following window after you insert the CD The setup guide will auto detect your motherboard and operating system. Note: If this window didn’t show up after you insert the Driver CD, please use file browser to locate and execute the file SETUP.EXE under your optical drive. A. Driver Installation To install the driver, please click on the Driver icon. The setup guide will list the compatible driver for your motherboard and operating system. Click on each device driver to launch the installation program. B. Software Installation To install the software, please click on the Software icon. The setup guide will list the software available for your system, click on each software title to launch the installation program. C. Manual Aside from the paperback manual, we also provide manual in the Driver CD. Click on the Manual icon to browse for available manual. Note: You will need Acrobat Reader to open the manual file. Please download the latest version of Acrobat Reader software from http://www.adobe.com/products/acrobat/readstep2.html 23 Motherboard Manual 5.2 SOFTWARE Installing Software 1. Insert the Setup CD to the optical drive. The drivers installation program would appear if the Autorun function has been enabled. 2. Select Software Installation, and then click on the respective software title. 3. Follow the on-screen instructions to complete the installation. BIOScreen Utility This utility allows you to personalize your boot logo easily. You can choose JPG or BMP as your boot logo so as to customize your computer. Please follow the following instructions to update boo logo: 1. Load Image:Choose the picture as the boot logo. 2. Transform:Transform the picture for BIOS and preview the result. 3. 24 Update Bios:Write the picture to BIOS Memory to complete the update. MCP6P M2+/N68S+ 5.3 AWARD BIOS BEEP CODE Beep Sound Meaning One long beep followed by two short beeps Video card not found or video card memory bad High-low siren sound CPU overheated System will shut down automatically One Short beep when system boot-up Long beeps every other second No error found during POST No DRAM detected or install 5.4 EXTRA INFORMATION CPU Overheated If the system shutdown automatically after power on system for seconds, that means the CPU protection function has been activated. When the CPU is over heated, the motherboard will shutdown automatically to avoid a damage of the CPU, and the system may not power on again. In this case, please double check: 1. The CPU cooler surface is placed evenly with the CPU surface. 2. CPU fan is rotated normally. 3. CPU fan speed is fulfilling with the CPU speed. After confirmed, please follow steps below to relief the CPU protection function. 1. Remove the power cord from power supply for seconds. 2. Wait for seconds. 3. Plug in the power cord and boot up the system. Or you can: 1. Clear the CMOS data. (See “Close CMOS Header: JCMOS1” section) 2. Wait for seconds. 3. Power on the system again. 25 Motherboard Manual 5.5 TROUBLESHOOTING Probable 1. There is no power in the system. Power LED does not shine; the fan of the power supply does not work 2. Indicator light on keyboard does not shine. System is inoperative. Keyboard lights are on, power indicator lights are lit, and hard drives are running. System does not boot from a hard disk drive, but can be booted from optical drive. Solution 1. 2. 3. Make sure power cable is securely plugged in. Replace cable. Contact technical support. Using even pressure on both ends of the DIMM, press down firmly until the module snaps into place. 1. Check cable running from disk to disk controller board. Make sure both ends are securely plugged in; check the drive type in the standard CMOS setup. 2. Backing up the hard drive is extremely important. All hard disks are capable of breaking down at any time. System only boots from an optical 1. Back up data and applications drive. Hard disks can be read, files. applications can be used, but system 2. Reformat the hard drive. fails to boot from a hard disk. Re-install applications and data using backup disks. Screen message shows “Invalid Review system’s equipment. Make sure Configuration” or “CMOS Failure.” correct information is in setup. System cannot boot after user installs a 1. Set master/slave jumpers second hard drive. correctly. 2. Run SETUP program and select correct drive types. Call the drive manufacturers for compatibility with other drives. 26 MCP6P M2+/N68S+ This page is intentionally left blank. 27 Motherboard Manual APPENDIX: SPEC IN OTHER LANGUAGES GERMAN Spezifikationen Sockel AM2+ CPU AMD Phenom / Phenom II / Athlon / Athlon II / Sempron Prozessoren Chipsatz Unterstützt HyperTransport mit einer Bandbreite von bis zu 1 GHz GeForce 6150 SE/nForce 430 (MCP6P M2+) GeForce 7025/nForce 630a (N68S+) ITE 8716F Super E/A Umgebungskontrolle, Bietet die häufig verwendeten alten Super Hardware-Überwachung E/A-Funktionen. Lüfterdrehzahl-Controller Low Pin Count-Schnittstelle "Smart Guardian"-Funktion von ITE DDR2 DIMM-Steckplätze x 2 Dual-Kanal DDR2 Speichermodul Arbeitsspeich Max. 8GB Arbeitsspeicher er Grafik 64-Bit-Datenverarbeitung Unterstützt Hyper Transport und Cool’n’Quiet (Maximales Watt: 95W) FSB Die AMD 64-Architektur unterstützt eine 32-Bit- und Unterstützt DDR2 533 / 667 / 800 / 1066 Jeder DIMM unterstützt registrierte DIMMs. ECC DIMMs werden nicht 256MB/512MB/1GB/2GB/4GB DDR2. unterstützt. GeForce 6150 SE/nForce 430 (MCP6P M2+) Max. 512MB gemeinsam benutzter Videospeicher GeForce 7025/nForce 630a (N68S+) (under OS) IDE Integrierter IDE-Controller SATA II Integrierter Serial ATA-Controller LAN Realtek RTL 8201CL Ultra DMA 33 / 66 / 100 / 133 Bus Master-Modus Unterstützt PIO-Modus 0~4, Datentransferrate bis zu 3Gb/s Konform mit der SATA-Spezifikation Version 2.0. 10 / 100 Mb/s Auto-Negotiation Halb-/ Vollduplex-Funktion 5.1-Kanal-Audioausgabe Audio-Codec ALC662 Unterstützt High-Definition Audio PCI-Steckplatz x2 PCI Express x16 Steckplatz x1 Onboard-Ans Diskettenlaufwerkanschluss x1 Jeder Anschluss unterstützt 2 Diskettenlaufwerke chluss x1 Jeder Anschluss unterstützt 1 Druckeranschluss Steckplätze 28 Druckeranschluss Anschluss MCP6P M2+/N68S+ Spezifikationen Rückseiten-E /A Platinengröße . Sonderfunkti onen OS-Unterstüt zung IDE-Anschluss x1 Jeder Anschluss unterstützt 2 IDE-Laufwerke SATA-Anschluss x4 Jeder Anschluss unterstützt 1 SATA-Laufwerk Fronttafelanschluss x1 Unterstützt die Fronttafelfunktionen Front-Audioanschluss x1 Unterstützt die Fronttafel-Audioanschlussfunktion CD-IN-Anschluss x1 Unterstützt die CD Audio-In-Funktion S/PDIF- Ausgangsanschluss x1 Unterstützt die digitale Audioausgabefunktion CPU-Lüfter-Sockel x1 System-Lüfter-Sockel x1 "CMOS löschen"-Sockel x1 USB-Anschluss x3 Stromanschluss (24-polig) x1 Stromanschluss (4-polig) x1 PS/2-Tastatur x1 PS/2-Maus x1 VGA-Anschluss x1 Serieller Anschluss x1 LAN-Anschluss x1 USB-Anschluss x4 Audioanschluss x3 CPU-Lüfterstromversorgungsanschluss (mit Smart Fan-Funktion) System-Lüfter-Stromversorgungsanschluss Jeder Anschluss unterstützt 2 Fronttafel-USB-Anschlüsse 190 mm (B) X 244 mm (L) Unterstützt RAID 0 / 1 / 0+1 / 5 BIOSTAR behält sich das Recht vor, ohne Windows XP / Vista / 7 Ankündigung die Unterstützung für ein Betriebssystem hinzuzufügen oder zu entfernen. 29 Motherboard Manual FRENCH SPEC Socket AM2+ UC Processeurs AMD Phenom / Phenom II / L'architecture AMD 64 permet le calcul 32 et 64 bits Athlon / Athlon II / Sempron Prend en charge Hyper Transport et Cool’n’Quiet (Watt maximum : 95W) Bus frontal Chipset Super E/S Prend en charge Hyper Transport jusqu'à une bande passante de1 GHz GeForce 6150 SE/nForce 430 (MCP6P M2+) GeForce 7025/nForce 630a (N68S+) ITE 8716F Initiatives de contrôle environnementales, Fournit la fonctionnalité de Super E/S Moniteur de matériel patrimoniales la plus utilisée. Contrôleur de vitesse de ventilateur Interface à faible compte de broches Fonction "Gardien intelligent" de l'ITE Fentes DDR2 DIMM x 2 Module de mémoire DDR2 à mode à double voie Mémoire Capacité mémoire maximale de 8 Go Prend en charge la DDR2 533 / 667 / 800 / 1066 principale Chaque DIMM prend en charge des DDR2 Les DIMM à registres et DIMM avec code correcteurs de 256 Mo/512 Mo et 1Go/2Go/4Go Graphiques d'erreurs ne sont pas prises en charge GeForce 6150 SE/nForce 430 (MCP6P M2+) Mémoire vidéo partagée maximale de 512 Mo (under GeForce 7025/nForce 630a (N68S+) IDE Contrôleur IDE intégré SATA II Contrôleur Serial ATA intégré : LAN Realtek RTL 8201CL OS) Mode principale de Bus Ultra DMA 33 / 66 / 100 / 133 Prend en charge le mode PIO 0~4, Taux de transfert jusqu'à 3 Go/s. Conforme à la spécification SATA Version 2.0 10 / 100 Mb/s négociation automatique Half / Full duplex capability Sortie audio à 5.1 voies Codec audio ALC662 Fentes Connecteur embarqué Fente PCI x2 Slot PCI Express x16 x1 Connecteur de disquette x1 Connecteur de Port d'imprimante x1 Connecteur IDE 30 Prise en charge de l'audio haute definition x1 Chaque connector prend en charge 2 lecteurs de disquettes Chaque connector prend en charge 1 Port d'imprimante Chaque connecteur prend en charge 2 périphériques IDE MCP6P M2+/N68S+ SPEC Chaque connecteur prend en charge 1 périphérique Connecteur SATA x4 Connecteur du panneau avant x1 Prend en charge les équipements du panneau avant Connecteur Audio du panneau avant x1 Prend en charge la fonction audio du panneau avant Connecteur d'entrée CD x1 Prend en charge la fonction d'entrée audio de CD Connecteur de sortie S/PDIF x1 Embase de ventilateur UC x1 Embase de ventilateur système x1 Embase d'effacement CMOS x1 Connecteur USB x3 Connecteur d'alimentation x1 SATA Prend en charge la fonction de sortie audio numérique Alimentation électrique du ventilateur UC (avec fonction de ventilateur intelligent) Alimentation électrique du ventilateur système Chaque connecteur prend en charge 2 ports USB de panneau avant (24 broches) Connecteur d'alimentation x1 (4 broches) Clavier PS/2 x1 Souris PS/2 x1 E/S du Port VGA x1 panneau Port série x1 arrière Port LAN x1 Port USB x4 Fiche audio x3 Dimensions de la carte 190 mm (l) X 244 mm (H) Fonctionnali tés Prise en charge RAID 0 / 1 / 0+1 / 5 spéciales Support SE Windows XP / Vista / 7 BIOSTAR se réserve le droit d'ajouter ou de supprimer le support de SE avec ou sans préavis. 31 Motherboard Manual ITALIAN SPECIFICA Socket AM2+ CPU Processori AMD Phenom / Phenom II / Athlon / Athlon II / Sempron (Watt massimo: 95W) FSB Chipset Supporto di Hyper Transport e Cool’n’Quiet GHz di larghezza di banda GeForce 6150 SE/nForce 430 (MCP6P M2+) GeForce 7025/nForce 630a (N68S+) Funzioni di controllo dell’ambiente: Fornisce le funzionalità legacy Super Monitoraggio hardware I/O usate più comunemente. Controller velocità ventolina Interfaccia LPC (Low Pin Count) Funzione "Smart Guardian" di ITE Alloggi DIMM DDR2 x 2 Memoria Capacità massima della memoria 8GB principale Ciascun DIMM supporta DDR2 Modulo di memoria DDR2 a canale doppio Supporto di DDR2 533 / 667 / 800 / 1066 DIMM registrati e DIMM ECC non sono supportati 256MB/ 512MB e 1GB/2GB/4GB Grafica e 64 bit Supporto di HyperTransport fino a1 ITE 8716F Super I/O L’architettura AMD 64 abilita la co mputazione 32 GeForce 6150 SE/nForce 430 (MCP6P M2+) La memoria video condivisa massima è di 512MB (under OS) GeForce 7025/nForce 630a (N68S+) Modalità Bus Master Ultra DMA 33 / 66 / 100 / IDE Controller IDE integrato 133 Supporto modalità PIO Mode 0-4 SATA II Controller Serial ATA integrato LAN Realtek RTL 8201CL Codec audio Alloggi Velocità di trasferimento dei dati fino a 3 Gb/s. Compatibile specifiche SATA Versione 2.0. Negoziazione automatica 10 / 100 Mb/s Capacità Half / Full Duplex Uscita audio 5.1 canali ALC662 Supporto audio High-Definit ion (HD) Alloggio PCI x2 Alloggio PCI Express x16 x1 Connettori Connettore floppy x1 Ciascun connettore supporta 2 unità Floppy su scheda Connettore Porta stampante x1 Ciascun connettore supporta 1 Porta stampante Connettore IDE x1 Ciascun connettore supporta 2 unità IDE Connettore SATA x4 Ciascun connettore supporta 1 unità SATA 32 MCP6P M2+/N68S+ SPECIFICA Connettore pannello frontale x1 Supporta i servizi del pannello frontale Connettore audio frontale x1 Supporta la funzione audio pannello frontale Connettore CD-in x1 Supporta la funzione input audio CD Connettore output SPDIF x1 Supporta la funzione d’output audio digitale Collettore ventolina CPU x1 Collettore ventolina sistema x1 Collettore cancellaz ione CMOS x1 Connettore USB x3 Connettore alimentazione x1 Alimentazione ventolina CPU (con funzione Smart Fan) Alimentazione ventolina di sistema Ciascun connettore supporta 2 porte USB pannello frontale (24 pin) Connettore alimentazione x1 (4 pin) Tastiera PS/2 x1 Mouse PS/2 x1 I/O Porta VGA x1 pannello Porta seriale x1 posteriore Porta LAN x1 Porta USB x4 Connettore audio x3 Dimension i scheda 190 mm (larghezza) x 244 mm (altezza) Caratterist iche Supporto RAID 0 / 1 / 0+1 / 5 speciali Sistemi operativi supportati BIOSTAR si riserva il diritto di aggiungere o Windows XP / Vista / 7 rimuovere il supporto di qualsiasi sistema operativo senza preavviso. 33 Motherboard Manual SPANISH Especificación Conector AM2+ CPU Procesadores AMD Phenom / Phenom II / Athlon / Athlon II / Sempron 64 bits Soporta las tecnologías Hyper Transport y Cool’n’Quiet (Vatio máximo: 95W) FSB La arquitectura AMD 64 permite el procesado de 32 y Admite HyperTransport con un ancho de banda de hasta1 GHz Conjunto de GeForce 6150 SE/nForce 430 (MCP6P M2+) chips GeForce 7025/nForce 630a (N68S+) ITE 8716F Súper E/S Iniciativas de control de entorno, Le ofrece las funcionalidades heredadas de Monitor hardware uso más común Súper E/S. Controlador de velocidad de ventilador Interfaz de cuenta Low Pin Función "Guardia inteligente" de ITE Ranuras DIMM DDR2 x 2 Módulo de memoria DDR2 de canal Doble Memoria Capacidad máxima de memoria de 8GB Admite DDR2 de 533 / 667 / 800 / 1066 principal Cada DIMM admite DDR de No admite DIMM registrados o DIMM compatibles con 256MB/512MB y 1GB/2GB/4GB ECC Gráficos GeForce 6150 SE/nForce 430 (MCP6P M2+) Memoria máxima de vídeo compartida de 512MB GeForce 7025/nForce 630a (N68S+) IDE Controlador IDE integrado SATA II Controlador ATA Serie Integrado Red Local Realtek RTL 8201CL Códecs de sonido Ranuras (under OS) Modo bus maestro Ultra DMA 33 / 66 / 100 / 133 Soporte los Modos PIO 0~4, Tasas de transferencia de hasta 3 Gb/s. Compatible con la versión SATA 2.0. Negociación de 10 / 100 Mb/s Funciones Half / Full dúplex Salida de sonido de 5.1 canales ALC662 Ranura PCI Ranura PCI Express x16 Soporte de sonido Alta Definición X2 X1 Conectores Conector disco flexible X1 Cada conector soporta 2 unidades de disco flexible en placa Conector Puerto de impresora X1 Cada conector soporta 1 Puerto de impresora Conector IDE X1 Cada conector soporta 2 dispositivos IDE Conector SATA X4 Cada conector soporta 1 dispositivos SATA 34 MCP6P M2+/N68S+ Especificación Conector de panel frontal X1 Soporta instalaciones en el panel frontal Conector de sonido frontal X1 Soporta funciones de sonido en el panel frontal Conector de entrada de CD X1 Soporta función de entrada de sonido de CD Conector de salida S/PDIF X1 Soporta función de salida de sonido digital Cabecera de ventilador de CPU X1 Cabecera de ventilador de sistema X1 Cabecera de borrado de CMOS X1 Conector USB X3 Conector de alimentación X1 Fuente de alimentación de ventilador de CPU (con función Smart Fan) Fuente de alimentación de ventilador de sistema Cada conector soporta 2 puertos USB frontales (24 patillas) Conector de alimentación X1 (4 patillas) Teclado PS/2 X1 Ratón PS/2 X1 Panel Puerto VGA X1 trasero de Puerto serie X1 E/S Puerto de red local X1 Tamaño de la placa Funciones especiales Puerto USB X4 Conector de sonido X3 190 mm. (A) X 244 Mm. (H) Admite RAID 0 / 1 / 0+1 / 5 Soporte de sistema operativo Windows XP / Vista / 7 BIOSTAR se reserva el derecho de añadir o retirar el soporte de cualquier SO con o sin aviso previo. 35 Motherboard Manual PORTUGUESE ESPECIFICAÇÕES Socket AM2+ CPU Processadores AMD Phenom / Phenom II / Athlon / Athlon II / Sempron Chipset Suporta a tecnologia HyperTransport com uma largura de banda até1 GHz GeForce 6150 SE/nForce 430 (MCP6P M2+) GeForce 7025/nForce 630a (N68S+) ITE 8716F Especificaçã o Super I/O Iniciativas para controlo do ambiente Proporciona as funcionalidades mais utilizadas em termos da especificação Super I/O. Ranhuras DIMM DDR2 x 2 principal Monitorização do hardware Controlador da velocidade da ventoinha Função "Smart Guardian" da ITE Interface LPC (Low Pin Count). Memória e 64 bits Suporta as tecnologias Hyper Transport e Cool’n’Quiet (Watt máximo: 95W) FSB A arquitectura AMD 64 permite uma computação de 32 Capacidade máxima de memória: 8 GB Cada módulo DIMM suporta uma memória DDR2 de 256 MB/512 MB & 1 GB/2 GB/4 GB Módulo de memória DDR2 de canal duplo Suporta módulos DDR2 533 / 667 / 800 / 1066 Os módulos DIMM registados e os DIMM ECC não são suportados Placa GeForce 6150 SE/nForce 430 (MCP6P M2+) Memória de vídeo máxima partilhada: 512 MB (under gráfica GeForce 7025/nForce 630a (N68S+) IDE Controlador IDE integrado SATA II Controlador Serial ATA integrado LAN Realtek RTL 8201CL Codec de som Ranhuras OS) Modo Bus master Ultra DMA 33 / 66 / 100 / 133 Suporta o modo PIO 0~4, Velocidades de transmissão de dados até 3 Gb/s. Compatibilidade com a especificação SATA versão 2.0. Auto negociação de 10 / 100 Mb/s Capacidade semi/full-duplex Saída de áudio de 5.1 canais ALC662 Suporta a especificação High-Definition Audio Ranhura PCI x2 Ranhura PCI Express x16 x1 Conectores Conector da unidade de disquetes x1 Cada conector suporta 2 unidades de disquetes na placa Conector da para impressora x1 Cada conector suporta 1 Porta para impressora Conector IDE x1 Cada conector suporta 2 dispositivos IDE 36 MCP6P M2+/N68S+ ESPECIFICAÇÕES Conector SATA x4 Cada conector suporta 1 dispositivo SATA Conector do painel frontal x1 Para suporte de várias funções no painel frontal Conector de áudio frontal x1 Suporta a função de áudio no painel frontal Conector para entrada de CDs x1 Suporta a entrada de áudio a partir de CDs Conector de saída S/PDIF x1 Suporta a saída de áudio digital Conector da ventoinha da CPU x1 Conector da ventoinha do sistema x1 Conector para limpeza do CMOS x1 Conector USB x3 Conector de alimentação x1 Alimentação da ventoinha da CPU (com a função Smart Fan) Alimentação da ventoinha do sistema Cada conector suporta 2 portas USB no painel frontal (24 pinos) Conector de alimentação x1 (4 pinos) Entradas/S aídas no painel traseiro Tamanho da placa Teclado PS/2 x1 Rato PS/2 x1 Porta VGA x1 Porta série x1 Porta LAN x1 Porta USB x4 Tomada de áudio x3 190 mm (L) X 244 mm (A) Característi cas Suporta as funções RAID 0 / 1 / 0+1 / 5 especiais Sistemas operativos suportados A BIOSTAR reserva-se o direito de adicionar ou Windows XP / Vista / 7 remover suporte para qualquer sistema operativo com ou sem aviso prévio. 37 Motherboard Manual POLISH SPEC Socket AM2+ Procesor Architektura AMD 64 umożliwia przetwarzanie 32 i 64 AMD Phenom / Phenom II / Athlon / bitowe Athlon II / Sempron Procesory Obsługa Hyper Transport oraz Cool’n’Quiet (Maksymalny Watt: 95W) FSB Chipset Obsługa HyperTransport o szerokości pasma do1 GHz GeForce 6150 SE/nForce 430 (MCP6P M2+) GeForce 7025/nForce 630a (N68S+) Gniazda DDR2 DIMM x 2 Moduł pamięci DDR2 z trybem podwójnego kanału Pamięć Maks. wielkość pamięci 8GB główna Każde gniazdo DIMM obsługuje moduły 256MB/512MB oraz 1GB/2GB/4GB DDR2 Grafika Zapewnia najbardziej powszechne funkcje Monitor H/W Super I/O. Kontroler prędkości wentylatora Interfejs Low Pin Count Funkcja ITE "Smart Guardian" GeForce 6150 SE/nForce 430 (MCP6P M2+) Maks. wielkość współdzielonej pamięci video wynosi GeForce 7025/nForce 630a (N68S+) IDE Zintegrowany kontroler IDE SATA II Zintegrowany kontroler Serial ATA LAN Realtek RTL 8201CL Kodek dźwiękowy Gniazda Złącza 512MB (under OS) Ultra DMA 33 / 66 / 100 / 133 Tryb Bus Master obsługa PIO tryb 0~4, Transfer danych do 3 Gb/s. Zgodność ze specyfikacją SATA w wersji 2.0. 10 / 100 Mb/s z automatyczną negocjacją szybkości Działanie w trybie połowicznego / pełnego dupleksu 5.1 kanałowe wyjście audio ALC662 Obsługa High-Definition Audio Gniazdo PCI x2 Gniazdo PCI Express x16 x1 Złącze napędu dyskietek x1 Każde złącze obsługuje 2 napędy dyskietek x1 Każde złącze obsługuje 1 Port drukarki Złącze IDE x1 Każde złącze obsługuje 2 urządzenia IDE Złącze SATA x4 Każde złącze obsługuje 1 urządzenie SATA Złącze panela przedniego x1 Obsługa elementów panela przedniego wbudowane Złącze Port drukarki 38 Brak obsługi Registered DIMM oraz ECC DIMM Funkcje kontroli warunków pracy, ITE 8716F Super I/O Obsługa DDR2 533 / 667 / 800 / 1066 MCP6P M2+/N68S+ SPEC Przednie złącze audio x1 Obsługa funkcji audio na panelu przednim Złącze wejścia CD x1 Obsługa funkcji wejścia audio CD Złącze wyjścia S/PDIF x1 Obsługa funkcji cyfrowego wyjścia audio Złącze główkowe wentylatora procesora x1 Złącze główkowe wentylatora systemowego x1 Zasilanie wentylatora procesora (z funkcją Smart Fan) Zasilanie wentylatora systemowego Złącze główkowe kasowania Back Panel I/O Wymiary płyty Funkcje specjalne CMOS x1 Złącze USB x3 Złącze zasilania (24 pinowe) x1 Złącze zasilania (4 pinowe) x1 Klawiatura PS/2 x1 Mysz PS/2 x1 Port VGA x1 Port szeregowy x1 Port LAN x1 Port USB x4 Gniazdo audio x3 operacyjne go przednim 190 mm (S) X 244 mm (W) Obsługa RAID 0 / 1 / 0+1 / 5 Obsluga systemu Każde złącze obsługuje 2 porty USB na panelu BIOSTAR zastrzega sobie prawo dodawania lub Windows XP / Vista / 7 odwoływania obsługi dowolnego systemu operacyjnego bez powiadomienia. 39 Motherboard Manual RUSSIAN СПЕЦ CPU Гнездо AM2+ (центральн Процессоры AMD Phenom / Phenom II / ый Athlon / Athlon II / Sempron Поддержка Hyper Transport и Cool’n’Quiet процессор) (Максимальный ватт: 95W) FSB Набор Архитектура AMD 64 разрешать обработка данных на 32 и 64 бит Поддержка HyperTransport с пропускной способностью до1GГц GeForce 6150 SE/nForce 430 (MCP6P M2+) микросхем GeForce 7025/nForce 630a (N68S+) Слоты DDR2 DIMM x 2 Модуль памяти с двухканальным режимом DDR2 Основная Максимальная ёмкость памяти 8 ГБ Поддержка DDR2 533 / 667 / 800 / 1066 память Каждый модуль DIMM поддерживает Не поддерживает зарегистрированные модули 256 МБ /512МБ & 1ГБ/2ГБ/4ГБ DDR2 DIMM and ECC DIMM ITE 8716F Обеспечивает наиболее используемые Super I/O действующие функциональные Регулятор скорости возможности Super I/O. Функция ITE "Smart Guardian" (Интеллектуальная Интерфейс с низким количеством защита) выводов Графика IDE SATA II Локальная сеть Звуковой кодек Слоты Встроенны й разъём GeForce 6150 SE/nForce 430 (MCP6P M2+) Максимальная совместно используемая видео GeForce 7025/nForce 630a (N68S+) память составляет 512 МБ (under OS) Встроенное устройство управления Режим "хозяина" шины Ultra DMA 33 / 66 / 100 / 133 встроенными интерфейсами устройств Поддержка режима PIO 0~4, Встроенное последовательное скорость передачи данных до 3 гигабит/с. устройство управления ATA Соответствие спецификации SATA версия 2.0. Автоматическое согласование 10 / 100 Мб/с Realtek RTL 8201CL Частичная / полная дуплексная способность 5.1канальный звуковой выход ALC662 Звуковая поддержка High-Definition Слот PCI x2 Слот PCI Express x16 x1 Разъём НГМД x1 Разъём Порт подключения принтера 40 Инициативы по охране окружающей среды, Аппаратный монитор Каждый разъём поддерживает 2 накопителя на гибких магнитных дисках Каждый разъём поддерживает 1 Порт подключения x1 Разъём IDE x1 Разъём SATA x4 принтера Каждый разъём поддерживает 2 встроенных интерфейса накопителей Каждый разъём поддерживает 1 устройство SATA MCP6P M2+/N68S+ СПЕЦ Разъём на лицевой панели x1 Поддержка устройств на лицевой панели Входной звуковой разъём x1 Поддержка звуковых функций на лицевой панели Разъём ввода для CD x1 Поддержка функции ввода для CD Разъём вывода для S/PDIF x1 Поддержка вывода цифровой звуковой функции Контактирующее приспособление x1 вентилятора центрального процессора Контактирующее приспособление вентилятора системы x1 Источник питания для вентилятора центрального процессора (с функцией интеллектуального вентилятора) Источник питания для вентилятора системы Открытое контактирующее приспособление CMOS x1 USB-разъём x3 Разъем питания (24 вывод) x1 Разъем питания (4 вывод) x1 Клавиатура PS/2 x1 Задняя Мышь PS/2 x1 панель Порт VGA x1 средств Последовательный порт x1 ввода-выв Порт LAN x1 USB-порт x4 ода Каждый разъём поддерживает 2 USB-порта на лицевой панели Гнездо для подключения наушников x3 Размер панели 190 мм (Ш) X 244 мм (В) Специальн ые технически е Поддержка RAID 0 / 1 / 0+1 / 5 характерис тики Поддержка OS BIOSTAR сохраняет за собой право добавлять или Windows XP / Vista / 7 удалять средства обеспечения для OS с или без предварительного уведомления. 41 Motherboard Manual ARABIC اﻟﻤﻮاﺻﻔﺎت AM2+ﻡﻘﺒﺲ وﺣﺪة اﻟﻤﻌﺎﻟﺠﺔ AMD Phenom / Phenom II /ﻡﻌﺎﻟﺠﺎت إﺝﺮاء اﻟﻌﻤﻠﻴﺎت اﻟﺤﺎﺳﻮﺏﻴﺔ ﺏﺴﺮﻋﺔ 32و 64ﺏﺖAMD 64ﺗﻤﻜﻦ ﺗﻘﻨﻴﺔ اﻟﻤﺮآﺰﻳﺔ Athlon / Athlon II / Sempron Cool’n’Quietو Hyper Transportﺗﺪﻋﻢ ﺗﻘﻨﻴﺔ )و: 95ﻗﺼ ﻮى واط( اﻟﻨﺎﻗﻞ اﻷﻡﺎﻡﻲ اﻟﺠﺎﻥﺒﻲ ﺗﺮدد 1000ﺏﺘﺮدد ﻳﺼﻞ إﻟﻰ HyperTransportﺗﺪﻋﻢ ﺗﻘﻨﻴﺔ )GeForce 6150 SE/nForce 430 (MCP6P M2+ ﻡﺠﻤﻮﻋﺔ اﻟﺸﺮاﺋﺢ )GeForce 7025/nForce 630a (N68S+ ﻓﺘﺤﺔ DDR2 DIMM ﻋﺪد2 ﺳﻌﺔ ذاآﺮة ﻗﺼﻮى 8ﺝﻴﺠﺎ ﺏﺎﻳﺖ اﻟﺬاآﺮة اﻟﺮﺋﻴﺴﻴﺔ ﺳﻌﺔ DDR2ﺗﺪﻋﻢ ذاآﺮة ﻡﻦ ﻥﻮع DIMMﺗﺪﻋﻢ آﻞ ﻓﺘﺤﺔ ﻡﻴﺠﺎ ﺏﺎﻳﺖ و 4/2/1ﺝﻴﺠﺎ ﺏﺎﻳﺖ256/512 اﻷآﺜﺮ اﺳﺘﺨﺪاﻡًﺎSuper I/O .ﺗﻮﻓﺮ وﻇﻴﻔﺔ ﻡﺮاﻗﺐ ﻓﻲ ﺳﺮﻋﺔ اﻟﻤﺮوﺣﺔ ITEﻡﻦ ""Smart Guardianوﻇﻴﻔﺔ )GeForce 6150 SE/nForce 430 (MCP6P M2+ )GeForce 7025/nForce 630a (N68S+ ﻡﻨﻔﺬ IDE ﻡﺘﻜﺎﻡﻞIDEﻡﺘﺤﻜﻢ SATA II ﻡﺘﻜﺎﻡﻞSerial ATAﻡﺘﺤﻜﻢ ﺵﺒﻜﺔ داﺥﻠﻴﺔ Realtek RTL 8201CL آﻮدﻳﻚ اﻟﺼﻮت ALC662 ) (under OSﻡﻴﺠﺎ ﺏﺎﻳﺖ512أﻗﺼﻰ ﺳﻌﺔ ﻟﺬاآﺮة اﻟﻔﻴﺪﻳﻮ اﻟﻤﺸﺘﺮآﺔ وﺿﻊ رﺋﻴﺴﻲUltra DMA 33 / 66 / 100 / 133ﻥﺎﻗﻞ ﺏﺘﻘﻨﻴﺔ PIO Mode 0~4دﻋﻢ وﺿﻊ ﻥﻘﻞ اﻟﺒﻴﺎﻥﺎت ﺏﺴﺮﻋﺎت ﺗﺼﻞ إﻟﻰ 3ﺝﻴﺠﺎﺏﺖ/ﺙﺎﻥﻴﺔ. 2.0.اﻹﺹﺪارSATAﻡﻄﺎﺏﻘﺔ ﻟﻤﻮاﺹﻔﺎت ﺗﻔﺎوض ﺗﻠﻘﺎﺋﻲ 100/10ﻡﻴﺠﺎ ﺏﺎﻳﺖ /ﺙﺎﻥﻴﺔ إﻡﻜﺎﻥﻴﺔ اﻟﻨﻘﻞ اﻟﻤﺰدوج اﻟﻜﺎﻡﻞ/اﻟﻨﺼﻔﻲ ﻗﻨﻮات ﻟﺨﺮج اﻟﺼﻮت5.1 ﺗﺪﻋﻢ ﺗﻘﻨﻴﺔ اﻟﺼﻮت ﻋﺎﻟﻲ اﻟﺘﻌﺮﻳﻒ ﻡﻦ ﻓﺘﺤﺔ PCI ﻋﺪد 2 ﻓﺘﺤﺔ PCI Express x16 ﻋﺪد 1 اﻟﻤﻨﺎﻓﺬ ﻋﻠﻰ ﺳﻄﺢ ﻡﻨﻔﺬ ﻡﺤﺮك أﻗﺮاص ﻡﺮﻥﺔ ﻋﺪد 1 اﻟﻠﻮﺣﺔ ﻡﻨﻔﺬ ﻃﺎﺏﻌﺔ ﻋﺪد 1 ﻡﻨﻔﺬ IDE ﻋﺪد 1 اﻟﻔﺘﺤﺎت ECCوﺗﻠﻚ اﻟﺘﻲ ﻻ ﺗﺘﻮاﻓﻖ ﻡﻊ DIMMﻻ ﺗﺪﻋﻢ رﻗﺎﺋﻖ اﻟﺬاآﺮة ﻡﺮاﻗﺐ ﻟﻤﻌﺮﻓﺔ ﺣﺎﻟﺔ اﻷﺝﻬﺰة Low Pin Count Interfaceﺗﺪﻋﻢ ﺗﻘﻨﻴﺔ ﺏﻄﺎﻗﺔ اﻟﺮﺳﻮﻡﺎت ﺳﻌﺎت 1066/800 / 667 / 533ﻡﻴﺠﺎ ﺏﺎﻳﺖDDR2ﺗﺪﻋﻢ اﻟﺬاآﺮة ﻡﻦ ﻥﻮع وﺳﺎﺋﻞ اﻟﺘﺤﻜﻢ ﻓﻲ اﻟﺒﻴﺌﺔ: ITE 8716F Super I/O ﻡﺰدوﺝﺔ اﻟﻘﻨﺎةDDR2وﺣﺪة ذاآﺮة ﻳﺪﻋﻢ ﻡﺤﺮآﻴﻦ ﻟﻸﻗﺮاص اﻟﻤﺮﻥﺔ IDEﻳﺪﻋﻢ آﻞ ﻡﻨﻔﺬ اﺙﻨﻴﻦ ﻡﻦ أﺝﻬﺰة 42 MCP6P M2+/N68S+ اﻟﻤﻮاﺻﻔﺎت ﻡﻨﺎﻓﺬ دﺥﻞ/ﺥﺮج اﻟﻠﻮﺣﺔ اﻟﺨﻠﻔﻴﺔ ﻡﻨﻔﺬ SATA ﻋﺪد 4 SATAﻳﺪﻋﻢ آﻞ ﻡﻨﻔﺬ واﺣﺪ ﻡﻦ أﺝﻬﺰة ﻡﻨﻔﺬ اﻟﻠﻮﺣﺔ اﻷﻡﺎﻡﻴﺔ ﻋﺪد 1 ﻳﺪﻋﻢ ﺗﺠﻬﻴﺰات اﻟﻠﻮﺣﺔ اﻷﻡﺎﻡﻴﺔ ﻡﻨﻔﺬ اﻟﺼﻮت اﻷﻡﺎﻡﻲ ﻋﺪد 1 ﻳﺪﻋﻢ وﻇﻴﻔﺔ اﻟﺼﻮت ﺏﺎﻟﻠﻮﺣﺔ اﻷﻡﺎﻡﻴﺔ ﻡﻨﻔﺬ CD-IN ﻋﺪد 1 ﻳﺪﻋﻢ وﻇﻴﻔﺔ دﺥﻞ ﺹﻮت اﻟﻘﺮص اﻟﻤﺪﻡﺞ ﻡﻨﻔﺬ ﺥﺮج S/PDIF ﻋﺪد 1 ﻳﺪﻋﻢ وﻇﻴﻔﺔ ﺥﺮج اﻟﺼﻮت اﻟﺮﻗﻤﻲ وﺹﻠﺔ ﻡﺮوﺣﺔ وﺣﺪة اﻟﻤﻌﺎﻟﺠﺔ اﻟﻤﺮآﺰﻳﺔ ﻋﺪد 1 Smart Fanﻟﺘﻮﺹﻴﻞ اﻟﻄﺎﻗﺔ ﻟﻤﺮوﺣﺔ وﺣﺪة اﻟﻤﻌﺎﻟﺠﺔ ﻡﻊ وﻇﻴﻔﺔ وﺹﻠﺔ ﻡﺮوﺣﺔ اﻟﻨﻈﺎم ﻋﺪد 1 ﻟﺘﻮﺹﻴﻞ اﻟﻄﺎﻗﺔ ﻟﻤﺮوﺣﺔ اﻟﻨﻈﺎم وﺹﻠﺔ ﻡﺴﺢ CMOS ﻋﺪد 1 ﻡﻨﻔﺬ USB ﻋﺪد 3 ﻡﻨﻔﺬ ﺗﻮﺹﻴﻞ اﻟﻄﺎﻗﺔ )24دﺏﻮس( ﻋﺪد 1 ﻡﻨﻔﺬ ﺗﻮﺹﻴﻞ اﻟﻄﺎﻗﺔ )4دﺏﺎﺏﻴﺲ( ﻋﺪد 1 ﻟﻮﺣﺔ ﻡﻔﺎﺗﻴﺢ PS/2 ﻋﺪد 1 ﻡﺎوس PS/2 ﻋﺪد 1 ﻡﻨﺎﻓﺬ VGA ﻋﺪد 1 ﻡﻨﻔﺬ ﺗﺴﻠﺴﻠﻲ ﻋﺪد 1 ﻡﻨﻔﺬ ﺵﺒﻜﺔ اﺗﺼﺎل ﻡﺤﻠﻴﺔ ﻋﺪد 1 ﻡﻨﺎﻓﺬ USB ﻋﺪد 4 ﻡﻘﺒﺲ ﺹﻮت ﻋﺪد 3 ﻡﺰاﻳﺎ ﺥﺎﺹﺔ RAID 0 / 1 / 0+1 / 5ﺗﺪﻋﻢ ﺗﻘﻨﻴﺔ ﺣﺠﻢ اﻟﻠﻮﺣﺔ 190ﻡﻢ )ﻋﺮض( 244 Xﻡﻢ )ارﺗﻔﺎع( دﻋﻢ أﻥﻈﻤﺔ اﻟﺘﺸﻐﻴﻞ Windows XP / Vista / 7 43 ﺏﺎﻟﻠﻮﺣﺔ اﻷﻡﺎﻡﻴﺔUSBﻳﺪﻋﻢ آﻞ ﻡﻨﻔﺬ ﻓﺘﺤﺘﻲ ﺏﺤﻘﻬﺎ ﻓﻲ إﺿﺎﻓﺔ أو إزاﻟﺔ اﻟﺪﻋﻢ ﻷي ﻥﻈﺎم ﺗﺸﻐﻴﻞ ﺏﺈﺥﻄﺎر أو ﺏﺪون BIOSTARﺗﺤﺘﻔﻆ إﺥﻄﺎر. Motherboard Manual JAPANESE 仕様 CPU FSB Socket AM2+ AMD 64アーキテクチャでは、32ビットと64ビット計算が可 AMD Phenom / Phenom II / Athlon / 能です Athlon II / Sempron プロセッサ ハイパートランスポートとクールアンドクワイアットをサポ (最高のワット: 95W) ートします 1GHzのバンド幅までハイパートランスポート をサポートします GeForce 6150 SE/nForce 430 (MCP6P M2+) チップセット GeForce 7025/nForce 630a (N68S+) DDR2 DIMMスロット x 2 デュアル チャンネルモードDDR2メモリモジュール 最大メモリ容量8GB メインメモリ 各DIMMは 256MB/512MB & 1GB/2GB/ 4GB DDR2をサポート ITE 8716F Super I/O もっとも一般に使用されるレガシーSuper I/O H/Wモニター 機能を採用しています。 ファン速度コントローラ/ モニター 低ピンカウントインターフェイス ITEの「スマートガーディアン」機能 ス GeForce 7025/nForce 630a (N68S+) IDE 統合IDEコントローラ SATA II 統合シリアルATAコントローラ LAN Realtek RTL 8201CL 最大の共有ビデオメモリは512MBです(under OS) Ultra DMA 33 / 66 / 100 / 133バスマスタモード PIO Mode 0~4のサポート、 最高3 Gb/秒のデータ転送速度 SATAバージョン2.0仕様に準拠。 10 / 100 Mb/秒のオートネゴシエーション 半/全二重機能 5.1チャンネルオーディオアウト ALC662 Codec スロット 登録済みDIMMとECC DIMMはサポートされません 環境コントロールイニシアチブ、 グラフィック GeForce 6150 SE/nForce 430 (MCP6P M2+) サウンド DDR2 533 / 667 / 800 / 1066をサポート ハイデフィニションオーディオのサポート PCIスロット x2 PCI Express x16スロット x1 オンボードコ フロッピーコネクタ x1 各コネクタは2つのフロッピードライブをサポートします ネクタ プリンタポートコネクタ x1 各コネクタは1つのプリンタポートをサポートします IDEコネクタ x1 各コネクタは2つのIDEデバイスをサポートします 44 MCP6P M2+/N68S+ 仕様 SATAコネクタ x4 各コネクタは1つのSATAデバイスをサポートします フロントパネルコネクタ x1 フロントパネル機能をサポートします フロントオーディオコネクタ x1 フロントパネルオーディオ機能をサポートします CDインコネクタ x1 CDオーディオイン機能をサポートします S/PDIFアウトコネクタ x1 デジタルオーディオアウト機能をサポートします CPUファンヘッダ x1 CPUファン電源装置(スマートファン機能を搭載) システムファンヘッダ x1 システムファン電源装置 CMOSクリアヘッダ x1 USBコネクタ x3 各コネクタは2つのフロントパネルUSBポートをサポートし ます 電源コネクタ(24ピン) x1 電源コネクタ(4ピン) x1 PS/2キーボード x1 PS/2マウス x1 VGAポート x1 シリアルポート x1 LANポート x1 USBポート x4 オーディオジャック x3 背面パネル I/O ボードサイズ 190 mm (幅) X 244 mm (高さ) 特殊機能 RAID 0 / 1 / 0+1 / 5 のサポート OSサポート Windows XP / Vista / 7 BIOSTARは事前のサポートなしにOSサポートを追加または 削除する権利を留保します。 2010/05/04 45
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.3 Linearized : Yes Create Date : 2010:05:04 17:00:14+08:00 Modify Date : 2010:05:04 17:00:14+08:00 Page Count : 47 Creation Date : 2010:05:04 09:00:14Z Mod Date : 2010:05:04 09:00:14Z Producer : Acrobat Distiller 5.0 (Windows) Author : 97031 Metadata Date : 2010:05:04 09:00:14Z Creator : 97031 Title : Microsoft Word - N61PB-M2S & N68SA-M2S_100504.docEXIF Metadata provided by EXIF.tools