Bissell 16N5 User Manual VACUUM Manuals And Guides L1002427
BISSELL Vacuum, Upright Manual L1002427 BISSELL Vacuum, Upright Owner's Manual, BISSELL Vacuum, Upright installation guides
User Manual: Bissell 16N5 16N5 BISSELL VACUUM - Manuals and Guides View the owners manual for your BISSELL VACUUM #16N5. Home:Vacuums & Floor Care Parts:Bissell Parts:Bissell VACUUM Manual
Open the PDF directly: View PDF 
.
Page Count: 20
| Download | |
| Open PDF In Browser | View PDF |
ii USER'S GUIDE 16N5 SERIES Instructions _roduct View )peration and Care Services ® for buyinga BISSELLHealthy Home VacuumTM We're glad you purchased a BISSELLvacuum. Everything we know about floor care went into the design and construction of this complete, nlgh-tech home cleaning system. By purchasing this product you are helping BISSELLwith our commitment to reducing our impact on the environment _nrougn an expanding range of sustainable design efforts. Your vacuum is well made, and we back it with a limited five year warranty. We also stand behind it with a knowledgeable, dedicated Consumer Services department, so, should you ever have a problem, you'll receive fast, considerate assistance. My great-grandfather invented the floor sweeper in 1876. Today, BISSELLis a global leader in the design, manufacture, and service of high quality homecare products like your carpet cleaner. Thanks again, from all of us at BISSELL. Mark J. Bissell President i and Chief Executive Officer 2¸¸¸¸¸¸¸ wwwbi sell00m 800.237.7691 TANT SAFETYINSTRUCTIONS When using an electrical appliance, basic precautions should be observed, including the following: READ ALL INSTRUCTIONS BEFOREUSINGYOUR UPRIGHTVACUUM. Always connectto a polarizedoutlet (one slot is wider than the other).Unplugfrom outlet when not in use and before conducting maintenance. WARNING: Toreduce the risk of fire, electric shock, or injury: • • • Do not modify the polarizedplug to fit a non-polarizedoutlet or extension cord. Do not leavevacuum cleaner unattended when it is plugged in. Unplug from outlet when not in use and before servicing. • Do not use outdoors or on wet surfaces. • Do not allow children to operatevacuum cleaner or use as a toy. • Close attention is necessarywhen used by or near children. • Do not use for any purposeotherthan describedin this User'sGuide. • Useonly manufacturer's recommended attachments. • Donotusewithdamagedcordor plug. • If appliance is not working as it should, has been dropped,damaged, left outdoors, or dropped into water, have it repaired at an authorized service center. • Turnoff all controls before plugging or unplugging vacuum cleaner. • Use extra care when cleaning stairs. • Unplug before attachingthe TurboBrush. • Do not pick up flammable materials(lighter fluid, gasoline, kerosene,etc.) or use in the presence of explosive liquids or vapors. • Do not pick up toxic material (chlorine bleach, ammonia, drain cleaner, etc.). • Do not use vacuumcleaner in an enclosedspace filledwith vaporsgiven off by oil base paint, paint thinner,some moth proofing substances,flammable dust, or other explosiveor toxicvapors. • Do not pick up hard or sharp objects such as glass, nails,screws, coins, etc. • Do not pickup anythingthat is burningor smoking, suchas cigarettes,matches,or hotashes. • Do not use without filters in place. • Use only on dry, indoorsurfaces. • Keepappliance on a level surface. • Do not carrythe vacuumcleanerwhile it is running. • Brush may unexpectedlyrestart. Unplug from outlet when cleaning or servicing. SAVETHESE INSTRUCTIONS FOR FUTURE USE THISAPPLIANCEHAS A POLARIZEDPLUG. • Do not pull or carry by cord,use cord as a handle, close a door on cord, or pull cord around sharp edges or corners. Do not run applianceover cord. Keepcord away from heatedsurfaces. To reducethe risk of electricshock,this appliancehas a polarizedplug(one bladeis widerthanthe other).This plug wiii fit ina polarizedoutletonlyone way.If the plug does not fit fullyinthe outlet,reversethe plug.if it still doesnot fit, contacta qualifiedelectricianto installa properoutlet. Do not changethe plug in anyway. • Do not unplug by pulling on cord.To unplug, grasp the plug, not the cord. This model is for householduse only. • Do not handlevacuum cleaneror plug with wet hands. • Do not put any objectinto openings.Do not use with any openingblocked;keep openingsfree of dust, lint, hair,and anythingthat may reduceair flow. • Keephair,looseclothing, fingers, and all partsof body awayfrom openingsand movingparts. www.bissell.com 800.237.7691 view Fingertip Power _gertip Brush On/Off TurboBrush ® Crevice Tool Long Hose QuickRebase CordWrap TM Telescoping Wand WandBase Brush Height Adjustment Dial BrushWindow Quick Furniture Protection Guard Brush HandleRelease Pedal FootHose 4 www.bissell.com 800.237.7691 CAUTION: Do not plug in your vacuum cleaner until you are familiar with all instructionsand operating procedures. Toolrequired:Phillipsscrewdriver 1, Slide upper handleinto lower handle by pushingforward. Inserttwo long screws into the holes marked with arrows and tighten bothuntil snug. 2, Attach hoserack by placingthe rack over the centerback portionof the vacuum. Be sure to feed the power cordthrough the hole inthe centerof the rack.Line up both screws holes and use the two smaller screws to attach.Tighten both until snug. 3, Attach hoseby placingthe tabbed endinto the lower left openingon cordedside of the vacuum.Makesure the tab on the hosecuff andthe hole in the vacuum line up. Place the working end of the hose into the hole on the side with the extensionwand guides. 4, 5, 2a 2b Arrangethe hoseso it laysbetweenthe vacuum andthe rack. Storethe TurboBrushon the front of the handle by aligningthe sloton the bottomwiththe tab on the handle.Snapinto place. 6. Storethe CombinationBrushinthe slotshown. 7. Makesurethe crevicetool is insidethe extensionwand.Storetools on vacuumas shown. www.bissell,com 800,237.7691 Transportingyour cleaner Usethe handleonthe fronttocarrythe cleaner or placethe cleanerin the uprightpositionand tip backto rollonthe rearwheels. Releasingthe powercord Theupperand lowercordwraps rotateto allow forquickand easyremovalof the powercord. Fingertip power switch Thepowerbuttonis locatedat the top ofthe vacuumhandle. Toturn cleaneron, press_) buttononce. Toturn cleanerOFF,press(_) buttonagain. Note:Therotatingbrushwill notturnon unlessthe unitis in the reclinedposition andthe brushswitchis on. Handle positions Useyourfoot to pullthe handlereleasepedal backto reclinethe vacuumcleaner. Heightadjustment Thereare sevenheightsettingsavailablefor variousfloorsurfaces.Turnthe dialon the foot of the cleanerto the desiredsetting. Lowestsetting- Forlowpile carpetor bare floors.Topick up debrisit may benecessaryto moveuponesetting. Mediumsettings - Formediumpilecarpet. Highsetting- Forhighpileandmostshagcarpet. Note:Foroptimalcarpetcleaning performance,adjustto the lowestpractical setting.If yourcleanerisdifficultto push, adjustto the nexthighersetting. ATTENTION: SomeBerbercarpetshavea tendencyto fuzzwith wear. Repeatedstrokesin the same area may aggravatethis condition.Considersettingyour cleaneron a higherthan normal setting for this typeof carpet. If the dial is difficultto turn,tilt the cleaner backslightlyto take the weightoffthe foot while turning. 6 www.bissell.com 800.237.7691 Fingertip brush switch Therotatingbrushisturnedon or offusingthe switchlocatedbelowthe powerswitchon the topof the handle.Thebrushwill startrotaUng whenthe unit is reclined.Thebrushshouldbe on for mostcarpetedfloors. Youmaywant to turnthe brushofffor barefloor cleaningor other delicatesurfaces. Toturnthe brushON,press_ buttononce. Toturnthe brushOFF,press_) buttonagain. Brushautoshut-offfeature Whenyourcleanerisin the uprightposition,the brushwill notrotate.Thebrushwill rotateonly whenthe cleaneris in the reclinedpositionand the brushswitchis on. Microban®antimicrobialproduct protection Microban ® antimicrobialprotectionfightsthe growthof odorcausingbacteria,moldand mildewin yourvacuum.It is built-into key componentsduringthe manufacturingprocess andwon't washoff or wearaway.Microban providescontinuousantimicrobialproduct protecUon for the usefullifetimeofthe product keepingyourvacuumcleanerandfresher. Note: Thisshouldnot replacenormal cleaningandmaintenanceprocedures. Microban is a registered trademark of Microban Products Company. www.bissell,com 800.237.7691 ATTENTION: Using the tools 1 2. 3. Make sure the cleaner is in the upright position. Always place the vacuum cleaner on the floor in its fully upright position when using tools. Placing the vacuum in this position automatically stops the rotating brush. Removethe hosewand from the wand base.This automaticallydiverts the suctionto the hose.Unwrapthe hosefrom the cleaner. Usethe hoseandwand aloneor attach any of the tools to the endof the hose wand. t TurboBrush Userotatingbrushactionfor smallareassuch as stairsandupholstery. Note: Pressgentlywhenusingthe TurboBrush to gainmaximumcleaning. Toomuchpressurecouldcausethe brush tostop rotating. Combination brush Uselongersoftbristlesfordusting. Removelong bristleportionanduse shorterstiff bristleswhen agitationis neededto removedebris. Crevice tool Usein tight narrowspaces Telescopingextensionwand Usewith desiredattachmentfora longermac& To extendthewand, twist the collarto "Unlock" and pushaway fromyou. Twistthe collarto "Lock" to lock intoplace. Toretract,twist to unlock,pull towardyouandtwist to relock. All availableitemsmay not be includedwith your model. Othertoolsare available;to order,please referto page19. i ¸8¸¸¸¸¸¸ wwwbisselloom ,,qt,,,,,,D- / CAUTION: To avoid personal injury and to prevent the cleaner from falling when cleaning stairs, always place it at the bottomof the stairs. 800.237.7691 / CAUTION: Make surevacuumcleaner hasbeenswitchedoff and unpluggedbeforeremoving dirtcontainer. Emptyingthe dirt container Emptythe dirtcontainerassoonasthe dirt reachesthe "Full" lineonthe sideof thecontainer. 1. Pressthe releasebutton on top of the carrying handleto removethe dirt container. 2, Choosean emptyingmethod.Method#2 is recommendedfor allergysufferers. Method#1 - hold the dirt containerover trash can andpush the emptyingbuttonto openthe bottom (2a).Closethe bottomafter the dirt empties. 2a 2b Method#2 - placea plasticbagoverme bottom of the dirt container.Pushthe emptyingbutton throughthe plas'dcto openthe bottom(2b).After the dustsettles,closethe bottomandremove the bagto discard. 3. Replacedirt container on cleanerby aligning the bottom and pushingback until it snaps into place. www.bissell,com 800.237.7691 _/ iii _ iintenance and care Cleaningthe dirt container Additionalstepscan betakento cleanthe dirt containeras necessary. 1. Ensurethe dirt container has been emptied. 2. Removethe lower portionby pressingthe front latch on the upperportion as shown. 3. Cleanthe screenwith a cloth or soft brush to removedust or debris. 4. If desired,the lower dirt container may be washedin warm water.Make sure it is completelydry beforereassembling.Do not put in dishwasher. 5. Toreassemble,hold the carry handle and place the upper portioninto the lower portion,lining up the front and back latches. Pushdown until both latchesclick into place. Makesure the dirt containeris securely assembledbefore replacingit on machine. !_iI i Z WARNING: To reduce the risk of electric shock, turn power switch OFFand disconnect polarizedplug from electrical outlet before performing maintenance or troubleshootingchecks. Cleaningthe pre-motorfilter Thepre-motorfilter shouldbe checkedmonthly andwashedas neededto maintainperformance. Moreor lessfrequent cleaningmaybe required basedonindividualvacuuminghabitsandtypes of debrispickedup. 1. Thefilter is located inthe door labeled "Filter" behind the dirt container.Pushthe tab at the top and swing the door down to access. 2. / WARNING: Donotoperatethecleanerwith a damporwet filter or withoutall thefilters in place. Removefoam filter andhold under running water to wash. Mild detergent may also be usedif desired.Wring excesswater from filter.Air dry thoroughlybeforereplacing. i¸ 10 www,bissell,com 800.237.7691 _i _ Maintenance and care Replacingthe HEPAfilter cartridge The HEPAfilter cartridgeshouldbe replacedif machineperformance is noticeablydeclining. More or less frequent replacingmay be requiredbased on individualvacuuminghabitsand types of debris picked up. Note: Tohavethe benefitsof the Airetight®HEPASystem_you must usethe BISSELLHEPAfilter cartridge. 1. Removethe dirt container. . , 4. , Toremovethe HEPAfilter cartridge, push in on the front of the filter door to unlatch. Lift up to access. Tocheck or remove,unscrewthe center screw. If necessary,replacethe used HEPA filter cartridge with a new one. Note: Toavoiddamagingthe HEPA filter cartridgeand reducingits filtration capabilities,be careful not to touchthe filter material.The HEPA filter cartridgeis not washable. Toensurea tightseal be sure to tighten the filter cartridgescrew until snug. DONOTOVERTIGHTEN. Make surethe filter door latches completely. www.bissell=com 800,237.7691 _ii ii iI i iintenance and care i_i _ii i i i [A WARNING: To reducethe risk of electric shock,turn power switch off and disconnect polarized plug from electrical outlet before performingmaintenanceor troubleshootingchecks. Clearingclogs Low suctionor poor pickup may be due to a clogin the vacuumcleaner.If you notice a changein the soundof the motoror a reductionin the spinningactionin the dirt container,checkfor a clog. Ifthereis nosuctionor if suctionis reduced at thehose,followthesestepsto checkfor andcleartheclog: . Turnpowerswitch off. 2. Unplugcleanerfrom electricaloutlet. 3. Checkthe pre-motorfilter and cleanas necessary(seecleaningyour pre-motor filter on page 10). . . 6. . 8. Checkto see if dirt containeris full. Emptyif needed. Removelower portion of dirt container. Cleanthe screen and check center tubes for dirt accumulation. Whiledirt container is removed,check dirt inletfor clogs. Removethehosefrom thecleanerby pushingon thetab.Straightenthe hose and checkfor a clog. Checkdiverterarea at backof machine for diverterpositionand clogs.Whenthe hosewand is removedfrom the base, the divertershouldbe up to the right. If a clogis visible nearthe diverter,the plastic covermay be removedto clearthe clogby removingthe 3 screws asshown (9b). 12 Inlet Checkthe HEPAfilter cartridge and replaceif necessary(seereplacingthe HEPAfilter cartridge on page11). www.bissell.com 9a 9b 800,237.7691 i Maintenance and care Clearingclogscontinued If suctionis normalat the hose,followthesesteps to checkfor andclearthe clogfor floorcleaning: 1. Checkdiverterareaat backof machinefor diverterposi'donandclogs.Whenthe hose wand is insertedin the base,me diverter shouldbe to the left. If a clogis visiblenearthe diverter,the plasticcovermay be removedto clearthe clog byremovingthe 3 screws. 2, Diverter FootHose Checkthe foot hosefor clogs (1). If you are not able to tell from the outsideif a clog is present,removethe bottom 3 screws from the divertercoverto loosenandstraighten the foot hose(2). Removeany clogs found and fully reassemblethe cleanerbefore attemptingto check suctionagain or using the cleaner. Thermal motorprotection An internalthermalprotectorhasbeendesigned intoyourcleanertoprotectit fromoverheating. Whenthethermalprotectoractivates,the main vacuummotorwill stopoperating.If thishappens, proceedasfollows. 1. 2, Turnthe cleanerOFFand unplug from electricaloutlet. Checkthe cleanerfor the sourceof overheatingproblem (i.e.full dirt cup, dirty filters or clog). 3, Fixthe problem by following the steps in the maintenancesectionof the user guide. 4. Whenthe motor coolsfor approximately 30 minutes,the thermal protector automaticallyresetsand cleaningmay continue.If the cleanerwill not turn on or the thermal protectorcontinuesto activate,your cleanermay need servicing.Call BISSELL ConsumerServicesor visit the website to locatean authorizedServiceCenter. Note:Thethermalprotectorcontrolsthe mainvacuummotoronly,notthe brush motor.If the thermalprotectoractivates, the brushwill continueto operatenormally; however,therewill beno suction. www.bissell.com 800.237.7691 iintenanceand care Brushreset If somethingbecomeslodgedin the foot andthe brushshutsoff,turnthe cleaneroffandunplug fromthe outlet.Removethe obstruction. The brushwill automaticallyresetwhenthe cleaner is pluggedin andturnedbackon. Brushmaintenance /KCAUTION: To reducethe riskof injury from movingparts,turn off the vacuumcleanerand disconnectpowerplugfrom electricaloutlet. Therotatingbrushshouldbecheckedregularly for accumulatingdebristhat mightreducethe cleaningperformanceofyourvacuum. 1. Unplugcleanerfrom electricaloutlet. 2. Reclinethe handle andturn your cleaner overso the bottomside is up. 3. Carefullycut away any visible hair,fibers or debrisfrom the brush roll. Donotattemptto disassemblethe vacuumfoot or to removethe brushroll.If youfeel it needsto becheckedor replaced,callBISSELLConsumer Servicesor visitthe websiteto locatean authorizedservicecenter. Belt maintenance Thebrushbeltisdesigned to lastthe usefullife of thecleanerwhenusedaccording to all instructions in the userguideundernormal household conditions. If youfeel thatit needsto becheckedor replaced, callBISSELL Consumer Servicesor visit thewebsiteto locateanaulhorized servicecenter.Donotattempttodisassemble the vacuumfootto changethe belt. 14 www,bissell,com 800.237.7691 Maintenance and care Changingthe light bulb 1. Turn powerswitch off. 2. Unplugcleanerfrom electricaloutlet. 3. Reclinehandlefor easieraccess to light bulb and remove2 screws to lift off lens. 4, Removethe bulb by grasping bulb and pulling straightout of the socket.Install the new bulb by pushing gently into the socket until the bulb snapsinto place. TurboBrushmaintenance TheTurboBrush shouldbecheckedregularlyfor clogsor debriswrappingaroundthe brush. 1. Removetool from hoseor front of vacuum. 2, Twist collar so openingis at the top and lift top coverto remove. 3. Removethe brushfrom the belt and clean debris. 4. Replacethe brush inside the belt and place endsinto slots on sidesas shown. 5, Repositiontop cover making sureto line up insidetab at the front with the openingon the cover.Twist collar until openingis at the bottomto lock into place. insideTab 5 www.bissell,com 800.237.7691 iiiiiiiiiiiiiii iubleshooting / WARNING: To reducethe risk of electric shock, turn power OFFand disconnect polarized plug from electrical outlet before performing maintenanceor troubleshooting. Vacuumcleanerwon'tturnon Possible causes Remedies 1. Powercordnot pluggedin 1. Checkelectricalplug 2. Blownfuse/trippedbreaker 2. Check/replacefuse or resetbreaker 3. Thermalprotectoractivated 3. Allowcleanerto coolfor 30 minutes,see pg. 13 4. Handlenotfully attached 4. Removehandleand reinstall Brushnot rotating Possible causes Remedies 1. Brushswitchturned to "Off" 1. Makesure brushswitchis in "On"position 2. Vacuumis in uprightposition 2. Reclinevacuumto operatebrush 3. Brush isjammed 3. Removeobstructionor debris(pg.14), unplugcleanerto resetbrush(pg.14) 4. Brush needsto be reset 4. Unplugcleanerto resetbrush(pg. 14) 5, Handlenotfully attached 5. Removehandleand reinstall Vacuumcleanerwon'tpick up or low suction Possiblecauses Remedies 16 1. Incorrectheightsetting 1. Turndial to lower setting 2. Hosewand notproperlypositioned 2. Makesure hosewand is fully seatedin baseand diverteris seatedto the left 3. Dirt containernot installedproperly 3. Checkassemblyd upperandlowerportions, correctlypositionandsnap into place 4. Dirt containerfull 4. Emptydirt container 5. Clogin cleaner 5. Followinstructionson pg. 12-13 for clearingclogs 6. Filtersare dirty 6. Checkand cleanfoamfilter,check and replaceHEPAfilter cartridgeif needed 7. Hosenot properlyattached 7, Makesure hosecollaris twistedto lock position 8. Fiberdoorand or gasketmissing or not installedproperly 8. Checkfilter doorand gasketto verify. www.bissell.com 800,237.7691 Vacuumcleaneris difficultto push Possible causes Remedies 1. 1. Turndialto highersetting Incorrectheightsetting Visibledustescapingfrom cleaner Possible causes Remedies 1. Filterdoorand or gasketmissing or not installedproperly 1. Checkfilter door andgasket 2. Foamfilter missingor notinstalledproperly 2, Checkfoamfilter for correctinstallation 3. HEPAfilter cartridge missingor not installedproperly 3. CheckHEPAfilter cartridgefor correctinstallation 4. Dirtcontainernot installedproperly 4. Make suredirt containeris correctly positionedandsnappedinto place 5. Dirtcontainernot assembledproperly 5. Checkscreen,upperand lowerportionsof the dirt containerfor properassembly 6. Hosenot installedproperly 6. Make surehosewand is fully seatedin base,andthat the hose is assembled correctlyto me unit.Seepage5. Alsomake surefoot hoseis properly attachedto diverterarea 7. Holeor crack in hose 7. Checkhosefor holesor cracks andreplace if needed Other maintenance or service not included in the manual should be performed by an authorized service representative. Thankyoufor selecting a BISSELLproduct. Pleasedo notreturnthisproductto the store.] ForanyqueslJonsorconcerns,BISSELL is happyto be ofservice. Contactusdirectlyat 1-800-237-7691. www bissell corn 800.237.7691 ConsumerServices For information about repairs or replacement parts, or questions about your warranty, call: BISSELLConsumer Services 1-800-237-7691 Monday - Friday 8 a.m. 10 p.m. EST Saturday 9 a.m. 8 p.m. EST Or writs: BISSELLHOMECARE, iNC POBox3606 GrandRapidsMI 49501 ATrN:ConsumerServices Or visitthe BISSELLwebsite- www,bissell,com WhencontactingBISSELL,havemodelnumberof cleaneravailable. Pleaserecordyour ModelNumber: Pleaserecordyour PurchaseDate: NOTE:Pleasekeepyouroriginalsalesreceipt.It providesproofof dateof purchasein the event ofa warrantyclaim.SeeWarrantyon page20 for details. Pleaseregisteryour new BISSELLproductat www, bissell.com/productregistration 18 www,bissell,com 800,237,7691 Replacement partsand accessories Youmay purchasepartsfromyourretailer,bycallingBISSELLConsumerServicesor by visitingour website.Belowis a listof commonreplacementparts*.Whilenotall ofthese partsmay havecomewith yourspecificmodel,theyare availablefor purchaseif desired. Pleasenote,all attachmentsmay notstoreonboardyourvacuum. Item Part No. Part Name 1 2 3 48G7 63M7 203-1362 HEPAFilterCartridge FoamFilter TurboBrush 4 5 6 7 8 203-1364 203-1365 203-1363 203-1382 203-1485 TelescopingWand CombinationBrush CreviceTool ContourTool Hose 9 203-1469 LightBulb *Not all parts are included with every model. Other tools may be available. Contact BISSELL Consumer Services or visit our website for more detail. Earn Rewards Points! To qualify you for discounts, rebates, and other BISSELLperks, Visit www,bissell,com/rewards to learn more, _i www.bissell.com 800.237.7691 ii_iI - BISSELL Healthy Home VacuumTM This warranty givesyou specific legal rights, and you may also have other rights which may vary from state to state. If you needadditional instruction regarding this warranty or have questions regardingwhat it may cover, please contact BISSELLConsumer Services by E-mail, telephone,or regular mail as described below. LimitedFive YearWarranty Subjectto the *EXCEPTIONSAND EXCLUSIONSidentified below, upon receipt of the product BISSELL Homecare, Inc. will repair or replace (with new or remanufactured components or products), at BISSELL'soption, free of chargefrom the date of purchase by the original purchaser,for five years on any defective or malfunctioning part. See information below on "If your BISSELLproductshould require service". This warrantyappliesto productusedfor personal,and not commercialor rentalservice.This warrantydoes notapply to fans or routinemaintenancecomponentssuch asfilters,or brushes.Damageor malfunctioncausedby negligence, abuse,neglect,unauthorizedrepair,or any other use not in accordancewith the User'sGuideis not covered. If your BISSELLproduct should require service: ContactBISSELL ConsumerServicesto locatea BISSELL AuthorizedServiceCenterinyourarea. If you needinformationaboutrepairsor replacementparts,or if youhavequestionsaboutyourwarranty, contactBISSELL ConsumerServices. Websiteor E-mail: www.bissell.com Usethe "CustomerService"tab. OrCall: BISSELL ConsumerServices 1-800-237-7691 Monday- Friday8 a.m.- 10p.m.ET Saturday9 a.m.- 8 p.m.ET Orwrite: BISSELL Homecare, Inc. P0 Box3606 GrandRapidsM149501 ATTN:ConsumerServices BlSSELL HOMECARE, INC.IS NOTLIABLEFORINCIDENTAL ORCONSEOUENTIAL DAMAGES OFANYNATURE ASSOCIATED WITHTHEUSEOFTHISPRODUCT. BlSSELL'S LIABILITY WILLNOTEXCEED THEPURCHASE PRICE OFTHEPRODUCT. Some states do not allow the exclusionor limitation of incidentalor consequentialdamages, so the above limitation or exclusionmay not apply to you. *EXCEPTIONSAND EXCLUSIONS FROMTHETERMSOFTHELIMITEDWARRANTY THISWARRANTYIS EXCLUSIVEAND IN LIEUOFANYOTHERWARRANTIES OPERATION OFLAW,INCLUDINGTHE IMPLIEDWARRANTIES OF MERCHANTABILITYBi EITHERORALORWRITTEN.ANY IMPLIEDWARRANTIES WHICHMAYARISEBY AND FITNESSFORA PARTICULAR PURPOSE,ARELIMITEDTO THEFIVEYEAR Ell DURATIONFROMTHEDATEOF PURCHASEAS DESCRIBEDABOVE. Some states do not allow limitations on how long an impliedwarranty lasts, so the above limitation may not apply to you. @2009 BISSELLHomecare, lee Grand Rapids,Michigan AI] fights reserved.Printedin China Part Number 110-41O0 Rev 5/09 Visit our websJteat: www.bLsseH.com 20 www.bissell.com 800.237.7691
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.2 Linearized : No Page Count : 20 Page Layout : SinglePage Page Mode : UseNone Producer : Goby Monitor Application version 4, 0, 0, 13 Create Date : Wed Mar 03 04:18:57 2010 Author : Title : Subject :EXIF Metadata provided by EXIF.tools