Bissell Heavy Duty Vacuum 50C9 Owners Manual

: Bissell Bissell-Heavy-Duty-Vacuum-50C9-Owners-Manual bissell-heavy-duty-vacuum-50c9-owners-manual bissell pdf

Open the PDF directly: View PDF .
Page Count: 20

Earn BISSELL Rewards!

Register your

product today!

See details on

back page

2Thank You

USER'S GUIDE

93Z6 SERIES

Safety Instructions

Product View

Assembly

Operations

Maintenance and Care

Troubleshooting

Consumer Services

Replacement Parts

3

4

5

6-9

10-15

16-17

20

18

Warranty

Product Registration

19

20

Earn BISSELL Rewards!

Register your

product today!

See details on

back page

www.bissell.com 800.237.7691

Thanks for buying a BISSELL Heavy Duty Vacuum

Everything we know about floor care went into the design and

construction of this complete, high-tech home cleaning system.

We trust that it will bring you many years of satisfaction. It is

backed with a limited five-year warranty. We also stand behind

it with a knowledgeable, dedicated Consumer Services depart-

ment, so, should you ever have a question, you’ll receive fast,

considerate assistance.

My great-grandfather invented the floor sweeper in 1876.

Today, BISSELL is a global leader in the design, manufacture,

and service of high quality homecare products like your Heavy

Duty Vacuum.

Thanks again, from all of us at BISSELL.

Mark J. Bissell

President and Chief Executive Officer

2

www.bissell.com 800.237.7691

IMPORTANT SAFETY INSTRUCTIONS

3

When using an electrical

appliance, basic

precautions should be observed, including

the following:

READ ALL

INSTRUCTIONS

BEFORE USING YOUR

UPRIGHT VACUUM.

Always connect to a polarized outlet

(left slot is wider than right). Unplug from

outlet when not in use and before conducting

maintenance.

WARNING: To

reduce the risk of fire,

electric shock, or injury:

■ Do not modify the polarized plug to fit a

non-polarized outlet or extension cord.

■ Do not leave vacuum cleaner unattended

when it is plugged in.

■ Unplug from outlet when not in use and

before servicing.

■ Do not use outdoors or on wet surfaces.

■ Do not allow children to operate vacuum

cleaner or use as a toy.

■ Close attention is necessary when used

by or near children.

■ Do not use for any purpose other than

described in this User’s Guide.

■ Use only manufacturer’s recommended

attachments.

■ Do not use with damaged cord or plug.

■ If appliance is not working as it should,

has been dropped, damaged, left out-

doors, or dropped into water, have it

repaired at an authorized service center.

■ Do not pull or carry by cord, use cord as

a handle, close a door on cord, or pull

cord around sharp edges or corners. Do

not run appliance over cord. Keep cord

away from heated surfaces.

■ Do not unplug by pulling on cord. To

unplug, grasp the plug, not the cord.

■ Do not handle vacuum cleaner or plug

with wet hands.

■ Do not put any object into openings. Do

not use with any opening blocked; keep

openings free of dust, lint, hair, and any-

thing that may reduce air flow.

■ Keep hair, loose clothing, fingers, and

all parts of body away from openings

and moving parts.

■ Turn off all controls before plugging or

unplugging vacuum cleaner.

■ Use extra care when cleaning stairs.

■ Unplug before attaching the TurboBrush.

■ Do not pick up flammable materials

(lighter fluid, gasoline, kerosene, etc.) or

use in the presence of explosive liquids

or vapors.

■ Do not pick up toxic material (chlorine

bleach, ammonia, drain cleaner, etc.).

■ Do not use vacuum cleaner in an

enclosed space filled with vapors given

off by oil base paint, paint thinner, some

moth proofing substances, flammable

dust, or other explosive or toxic vapors.

■ Do not pick up hard or sharp objects

such as glass, nails, screws, coins, etc.

■ Do not pick up anything that is burning

or smoking, such as cigarettes, matches,

or hot ashes.

■ Do not use without filters in place.

■ Use only on dry, indoor surfaces.

■ Keep appliance on a level surface.

■ Do not carry the vacuum cleaner while it

is running.

■ Brush may unexpectedly restart. Unplug

from outlet when cleaning or servicing.

SAVE THESE

INSTRUCTIONS

FOR FUTURE USE

THIS APPLIANCE

HAS A POLARIZED

PLUG.

To reduce the risk of electric shock, this

appliance has a polarized plug (one blade

is wider than the other). This plug will fit in

a polarized outlet only one way. If the plug

does not fit fully in the outlet, reverse the

plug. If it still does not fit, contact a qualified

electrician to install a proper outlet. Do not

change the plug in any way.

This model is for household use only.

www.bissell.com 800.237.7691

4

Product view

Upper Handle

Hose

TurboBrush

®

Crevice Tool

Telescoping

Extension

Wand

Dirt Container

Headlight

Height

Adjustment

Dial

Brush

Furniture

Protection Guard

Release

Button

Carrying

Handle

Filter Door

Latch

Screen Post-Motor

Filter (inside)

Filter Tray

(foam filter

inside)

Brush

Window

Power Switch

Brush Switch

Hose Collar

Handle Release

Pedal

Quick Release

™

Cord Wraps

Hose

Wand

Wand

Base

Diverter

Foot Hose

Lower Hose Clip

Power Cord

www.bissell.com 800.237.7691

Assembly

Tool required: Phillips screwdriver

1. Slide upper handle onto lower handle.

Insert one screw into hole marked with

an arrow and tighten until snug.

2. Attach hose by lining up the tabs on the

collar with the corresponding notches on

the back of the vacuum as shown. Turn

clockwise to lock the hose into place.

3. Wrap the hose by routing it down and

into the lower hose clip then up and over

the top of the handle. Insert the hose

wand fully into the hose base.

Note: It is important that the hose

is fully inserted into the base for

the suction air to be directed prop-

erly to the foot during floor vacu-

uming.

4. Store TurboBrush on the front of the

handle by aligning the slot at the bottom

with the tab and snapping into place.

5. Place crevice tool inside telescoping

extension wand. Store tools on vacuum

as shown.

5

CAUTION:

Do not plug in your vacuum

cleaner until you are familiar

with all instructions and

operating procedures.

12

4

5

3

www.bissell.com 800.237.7691

Operations

6

Transporting your cleaner

Use the handle on the front to carry

the cleaner or place the cleaner in the

upright position and tip back to roll on

the rear wheels.

Releasing the power cord

The upper and lower cord wraps rotate

to allow for quick and easy removal of

the power cord.

Fingertip power switch

The power button is located at the top

of the vacuum handle.

To turn cleaner ON, press button once.

To turn cleaner OFF, press button again.

Note: The rotating brush will not turn

on unless the unit is in the reclined

position and the brush switch is on.

Handle positions

Use your foot to pull the handle release

pedal back to recline the vacuum cleaner.

Height adjustment

There are seven height settings

available for various floor surfaces.

Turn the dial on the foot of the cleaner

to the desired setting.

Lowest setting – For bare floors.

Medium settings – For short and medi-

um pile carpets.

High setting – For plush carpet.

Note: For optimal cleaning

performance, adjust to the lowest

practical setting. If your cleaner is

difficult to push, adjust to the next

higher setting.

If the dial is difficult to turn, tilt the

cleaner back slightly to take the weight

off the foot while turning.

ATTENTION:

Some Berber carpets have a

tendency to fuzz with wear.

Repeated strokes in the same

area may aggravate this

condition. Consider setting

your cleaner on a higher than

normal setting for this type of

carpet.

Fingertip brush switch

The rotating brush is turned on or off

using the switch located below the

power switch on the top of the han-

dle. The brush will start rotating when

the unit is reclined. The brush should

be on for most carpeted floors. You

may want to turn the brush off for

bare floor cleaning or other delicate

surfaces.

To turn the brush ON, press button

once.

To turn the brush OFF, press button

again.

Brush auto shut-off feature

When your cleaner is in the upright

position, the brush will not rotate.

The brush will rotate only when the

cleaner is in the reclined position and

the brush switch is on.

www.bissell.com 800.237.7691

7

Operations

www.bissell.com 800.237.7691

Operations

8

Using the tools

1. Make sure the cleaner is in the upright

position.

2. Remove the hose wand from the wand

base. This automatically diverts the

suction to the hose. Unwrap the hose from

the cleaner.

3. Use the hose and wand alone or attach

any of the tools to the end of the hose

wand.

TurboBrush

Use rotating brush action for small

areas such as stairs and upholstery.

Note: Press gently when using the

TurboBrush to gain maximum

cleaning. Too much pressure could

cause the brush to stop rotating.

Combination brush

Use longer soft bristles for dusting.

Remove long bristle portion and use

shorter stiff bristles when agitation is

needed to remove debris.

Upholstery tool

Use shorter stiff bristles when agitation

is needed to remove debris.

Crevice tool

Use in tight narrow spaces

Telescoping extension wand

Use with desired attachment for a

longer reach. To extend the wand, twist

the collar to “Unlock” and push away

from you. Twist the collar to “Lock”

to lock into place. To retract, twist to

unlock, pull toward you and twist to

relock.

All available items may not be included

with your model. Other tools are

available; to order, please refer to page

18-19.

ATTENTION:

Always place the vacuum

cleaner on the floor in its fully

upright position when using

tools. Placing the vacuum in

this position automatically

stops the rotating brush.

CAUTION:

To avoid personal injury

and to prevent the cleaner

from falling when cleaning

stairs, always place it at

the bottom of the stairs.

2.

www.bissell.com 800.237.7691

9

Operations

Emptying the dirt container

Empty the dirt container as soon as the

dirt reaches the “Full” line on the side of

the container.

1. Press the release button on top of the

carrying handle to remove the dirt

container.

2. Choose an emptying method. Method #2

is recommended for allergy sufferers.

Method #1 – hold the dirt container over

trash can and push the emptying button

to open the bottom (2a). Close the bottom

after the dirt empties.

Method #2 – place a plastic bag over the

bottom of the dirt container. Push the empty-

ing button through the plastic to open the

bottom (2b). After the dust settles, close the

bottom and remove the bag to discard.

3. Replace dirt container on cleaner by align-

ing the bottom and pushing back until it

snaps into place.

CAUTION:

Make sure vacuum cleaner

has been switched off

and unplugged before

removing dirt container.

1.

2b.

3.

2a.

www.bissell.com 800.237.7691

Maintenance and care

10

Cleaning the dirt container

Additional steps can be taken to clean

the dirt container as necessary.

1. Ensure the dirt container has been

emptied.

2. Remove the lower portion by pressing the

front latch on the upper portion as shown.

3. Clean the screen with a cloth or soft brush

to remove dust or debris.

4. If desired, the lower dirt container may be

washed in warm water. Make sure it is

completely dry before reassembling.

Do not put in dishwasher.

5. To reassemble, hold the carry handle and

place the upper portion into the lower

portion, lining up the front and back

latches. Push down until both latches click

into place. Make sure the dirt container is

securely assembled before replacing it on

machine.

Cleaning the foam filter

The pre-motor filter should be checked

monthly and washed as needed to

maintain performance. More or less

frequent cleaning may be required

based on individual vacuuming habits

and types of debris picked up .

1. The foam filter is located in the tray

labeled "Filter" underneath the dirt

container. Pull the tray out to access

the filter.

2. Remove foam filter from tray and hold

under running water to wash. Mild deter-

gent may also be used if desired. Wring

excess water from filter. Air dry thor-

oughly before replacing.

WARNING:

Do not operate the cleaner with a

damp or wet filter or without all

the filters in place.

WARNING:

To reduce the risk of

electric shock, turn power

switch OFF and disconnect

polarized plug from electri-

cal outlet before performing

maintenance or

troubleshooting checks.

3.

5.

2.

1.

Replacing the post-motor filter cartridge

www.bissell.com 800.237.7691

11

Maintenance and care

The post-motor filter cartridge should be

replaced every six months or if

suction is declining. More or less

frequent replacing may be required

based on individual vacuuming habits

and types of debris picked up.

1. To remove the filter cartridge, push down

on the filter door latch and pull door

away from the cleaner.

2. Lift the tab at the top of the filter cartridge

and pull cartridge away from the cleaner.

3. Replace the used filter cartridge with a

new one.

Note: To avoid damaging the

filter cartridge and reducing its

filtration capabilities, be careful

not to touch the filter material.

The white pleated filter is not

washable.

4. To ensure a tight seal, the filter cartridge

must latch fully in place. To install, push

firmly near the top with the palm of your

hand while holding the vacuum with your

other hand.

1.

2.

4.

www.bissell.com 800.237.7691

Maintenance and care

12

Clearing clogs

Low suction or poor pickup may

be due to a clog in the vacuum

cleaner. If you notice a change in

the sound of the motor or a

reduction in the spinning action in

the dirt container, check for a clog.

If there is no suction or if suction is

reduced at the hose, follow these

steps to check for and clear the clog:

1. Unplug cleaner from electrical outlet.

2. Check the foam filter and clean as

necessary (see cleaning your foam filter

on page 10).

3. Check the post-motor filter and replace if

necessary (see replacing the filter

cartridge on page 11).

4. Check to see if dirt container is full. Empty

if needed.

5. Remove lower portion of dirt container.

Clean the screen and check center tubes

for dirt accumulation.

6. While dirt container is removed, check

dirt inlet for clogs.

7. Remove the hose from the cleaner by twist-

ing the collar counterclockwise. Straighten

the hose and check for a clog.

8 Check diverter area at back of machine

for diverter position and clogs. When the

hose wand is removed from the base, the

diverter should be up (8a). If a clog is

visible near the diverter, the plastic cover

may be removed to clear the clog by

removing the 7 screws as shown (8b).

Note: When removing and reinstall-

ing the plastic cover, make sure

the rope gasket remains fully in its

track.

WARNING:

To reduce the risk of electric

shock, turn power switch off

and disconnect polarized

plug from electrical outlet

before performing

maintenance or

troubleshooting checks.

6.

7.

8.

8a.

8b.

www.bissell.com 800.237.7691

13

Maintenance and care

1.

2a. 2b.

Clearing clogs continued

If suction is normal at the hose, follow

these steps to check for and clear the

clog for floor cleaning:

1. Check the foot hose for clogs. If you are

not able to tell from the outside if a clog is

present, remove the bottom 3 screws from

the diverter cover to loosen and straighten

the foot hose.

2. Remove any clogs found and fully reassemble

the cleaner before attempting to check suction

again or using the cleaner.

Thermal motor protection

An internal thermal protector has been

designed into your cleaner to protect it

from overheating. When the thermal

protector activates, the main vacuum

motor will stop operating. If this hap-

pens, proceed as follows.

1. Turn the cleaner OFF and unplug from

electrical outlet.

2. Check the cleaner for the source of over-

heating problem (i.e. full dirt cup, dirty

filters or clog).

3. Fix the problem by following the steps in

the maintenance section of the user guide.

4. When the motor cools for approximately

30 minutes, the thermal protector automat-

ically resets and cleaning may continue.

If the cleaner will not turn on or the ther-

mal protector continues to activate, your

cleaner may need servicing. Call BISSELL

Consumer Services or visit the website.

Note: The thermal protector controls

the main vacuum motor only, not the

brush motor. If the thermal protec-

tor activates, the brush will continue

to operate normally; however, there

will be no suction.

www.bissell.com 800.237.7691

Maintenance and care

14

Brush reset

If something becomes lodged in the foot

and the brush shuts off, turn the cleaner

off and unplug from the outlet. Remove

the obstruction. The brush will automati-

cally reset when the cleaner is plugged

in and turned back on.

If the vacuum does not re-start then

turn the cleaner off and unplug from

outlet. Wait 30 minutes while the motor

cools. The thermal protector automati-

cally resets and cleaning may continue.

Brush maintenance

The rotating brush should be checked

regularly for accumulating debris that

might reduce the cleaning performance

of your vacuum.

1. Unplug cleaner from electrical outlet.

2. Recline the handle and turn your cleaner

over so the bottom side is up.

3. Carefully cut away any visible hair, fibers

or debris from the brush roll.

Do not attempt to disassemble the

vacuum foot or to remove the brush

roll. If you feel it needs to be checked or

replaced, call BISSELL Consumer Services

or visit the website to locate an

authorized service center.

Belt maintenance

The brush belt is designed to last the

useful life of the cleaner when used

according to all instructions in the

user guide under normal household

conditions. If you feel that it needs to

be checked or replaced, call BISSELL

Consumer Services or visit the website to

locate an authorized service center. Do

not attempt to disassemble the vacuum

foot to change the belt.

CAUTION:

To reduce the risk of injury

from moving parts, turn off

the vacuum cleaner and

disconnect power plug from

electrical outlet.

3.

www.bissell.com 800.237.7691

15

Maintenance and care

Changing the light bulb

1. Turn power switch off.

2. Unplug cleaner from electrical outlet.

3. Recline handle for easier access to light

bulb and remove screw to lift off lens.

4. Remove the bulb by grasping bulb and

pulling straight out of the socket. Install

the new bulb by pushing gently into the

socket until the bulb snaps into place.

TurboBrush maintenance

The TurboBrush should be checked

regularly for clogs or debris wrapping

around the brush.

1. Remove tool from hose or front of vacuum.

2. Twist collar so opening is at the top and

lift top cover to remove.

3. Remove the brush from the belt and clean

debris.

4. Replace the brush inside the belt and

place ends into slots on sides as shown.

5. Reposition top cover making sure to line

up inside tab at the front with the opening

on the cover. Twist collar until opening is

at the bottom to lock into place.

3.

4.

2.

4.

5.

5.

www.bissell.com 800.237.7691

Troubleshooting

www.bissell.com 800.237.7691

16

Vacuum cleaner won’t turn on

Possible causes Remedies

1. Power cord not plugged in 1. Check electrical plug

2. Blown fuse/tripped breaker 2. Check/replace fuse or reset breaker

3. Thermal protector activated 3. Allow cleaner to cool for 30 minutes, see pg. 13

4. Handle not fully attached 4. Remove handle and reinstall

Brush not rotating

Possible causes Remedies

1. Brush switch turned to “Off” 1. Make sure brush switch is in “On” position

2. Vacuum is in upright position 2. Recline vacuum to operate brush

3. Brush is jammed 3. Remove obstruction or debris (pg. 14), unplug cleaner to

reset brush (pg. 14)

4. Brush needs to be reset 4. Unplug cleaner to reset brush (pg. 14)

5. Handle not fully attached 5. Remove handle and reinstall

6. Thermal protector activated 6. Allow cleaner to cool for 30 minutes, see page 14.

Vacuum cleaner won’t pick up or low suction

Possible causes Remedies

1. Incorrect height setting 1. Turn dial to lower setting

2. Hose wand not properly positioned 2. Make sure hose wand is fully seated in base and diverter is

seated to the left

3. Dirt container not installed properly 3. Check assembly of upper and lower portions, correctly

position and snap into place

4. Dirt container full 4. Empty dirt container

5. Clog in cleaner 5. Follow instructions on pg. 12-13 for clearing clogs

6. Filters are dirty 6. Check and clean foam filter, check and replace post-motor

cartridge if needed

7. Hose not properly attached 7. Make sure hose collar is twisted to lock position

WARNING:

To reduce the risk of electric

shock, turn power OFF and

disconnect polarized plug from

electrical outlet before performing

maintenance or troubleshooting.

www.bissell.com 800.237.7691

17

Troubleshooting

Vacuum cleaner is difficult to push

Possible causes Remedies

1. Incorrect height setting 1. Turn dial to higher setting

Visible dust escaping from cleaner

Possible causes Remedies

1. Filter door and or gasket missing 1. Check filter door and gasket

or not installed properly

2. Foam filter missing or not installed properly 2. Check foam filter for correct installation

3. Post-motor cartridge missing or not installed properly 3. Check Post-motor filter cartridge for correct installation

4. Dirt container not installed properly 4. Make sure dirt container is correctly positioned and snapped

into place

5. Dirt container not assembled properly 5. Check screen, upper and lower portions of the dirt container

for proper assembly

6. Hose not installed properly 6. Make sure hose wand is fully seated in base, and that the

hose is assembled correctly to the unit. See page 5. Also

make sure foot hose is properly attached to diverter area

7. Hole or crack in hose 7. Check hose for holes or cracks and replace if needed

Other maintenance or service not included in the manual should be

performed by an authorized service representative.

Thank you for selecting a BISSELL product.

Please do not return this product to the store.

For any questions or concerns, BISSELL is happy to be of

service. Contact us directly at 1-800-237-7691.

www.bissell.com 800.237.7691

Replacement parts - BISSELL vacuum

18

You may purchase parts from your retailer, by calling BISSELL

Consumer Services or by visiting our website. Below is a list of com-

mon replacement parts*. While not all of these parts may have come

with your specific model, they are available for purchase if desired.

Please note, all attachments may not store on board your vacuum.

Item Part No. Part Name

1 3282 Post-Motor Filter Cartridge

2 203-1374 Foam Filter

3 203-1429 TurboBrush

4 203-1290 Pet Wide TurboBrush

5 203-1364 Telescoping Wand

6 203-1373 Metal Telescoping Wand

7 203-1365 Combination Brush

8 203-1363 Crevice Tool

9 203-1291 Contour Tool

10 203-1359 Hose

11 203-1377 Light Bulb

12 203-1434 Upholstery Tool

*Not all parts are included with every model. Other tools may be available.

Contact BISSELL Consumer Services or visit our website for more detail.

1 2 3 4 5 6

7 8 9 10 11 12

www.bissell.com 800.237.7691

19

Warranty - BISSELL PowerClean® Vacuum

This warranty gives you specific legal rights, and you may also have other rights which may

vary from state to state. If you need additional instruction regarding this warranty or have

questions regarding what it may cover, please contact BISSELL Consumer Services by E-mail,

telephone, or regular mail as described below.

Limited Five Year Warranty

Subject to the *EXCEPTIONS AND EXCLUSIONS identified below, upon receipt of the product

BISSELL Homecare, Inc. will repair or replace (with new or remanufactured components or

products), at BISSELL’s option, free of charge from the date of purchase by the original

purchaser, for five years any defective or malfunctioning part.

See information below on "If your BISSELL product should require service".

This warranty applies to product used for personal, and not commercial or rental service. This

warranty does not apply to fans or routine maintenance components such as filters, belts, or

brushes. Damage or malfunction caused by negligence, abuse, neglect, unauthorized repair, or any

other use not in accordance with the User's Guide is not covered.

If your BISSELL product should require service:

Contact BISSELL Consumer Services to locate a BISSELL Authorized Service Center in your

area.

If you need information about repairs or replacement parts, or if you have questions about

your warranty, contact BISSELL Consumer Services.

Website or E-mail:

www.bissell.com

Use the “Customer Support” tab.

Or Call:

BISSELL Consumer Services

1-800-237-7691

Monday - Friday 8 a.m. - 10 p.m. ET

Saturday 9 a.m. - 8 p.m. ET

Or Write:

BISSELL Homecare, Inc.

PO Box 3606

Grand Rapids, MI 49501

ATTN: Consumer Services

BISSELL HOMECARE, INC. IS NOT LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES

OF ANY NATURE ASSOCIATED WITH THE USE OF THIS PRODUCT. BISSELL’S LIABILITY WILL NOT

EXCEED THE PURCHASE PRICE OF THE PRODUCT.

Some states do not allow the exclusion or limitation of incidental or consequential

damages, so the above limitation or exclusion may not apply to you.

*EXCEPTIONS AND EXCLUSIONS FROM THE TERMS OF THE LIMITED WARRANTY

THIS WARRANTY IS EXCLUSIVE AND IN LIEU OF ANY OTHER WARRANTIES EITHER ORAL OR

WRITTEN. ANY IMPLIED WARRANTIES WHICH MAY ARISE BY OPERATION OF LAW, INCLUDING

THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE,

ARE LIMITED TO THE FIVE YEAR DURATION FROM THE DATE OF PURCHASE AS DESCRIBED

ABOVE.

Some states do not allow limitations on how long an implied warranty last so the

above limitation may not apply to you.

Registering is quick, easy and offers you benefits over the lifetime of your product.

You’ll receive:

BISSELL Rewards Points

Automatically earn points for discounts and free shipping on future purchases.

Faster Service

Supplying your information now saves you time should you need to contact us with

questions regarding your product.

Product Support Reminders and Alerts

We’ll contact you with any important product maintenance reminders and alerts.

Special Promotions

Optional: Register your email to receive notice of offers, contests, cleaning tips and more!

Visit www.bissell.com/registration now!

Don't forget to register your product!

©2013 BISSELL Homecare, Inc

Grand Rapids, Michigan

All rights reserved. Printed in China

Part Number 160-3162

Rev 9/13

Visit our website at:

www.bissell.com

For information about repairs or replacement parts, or questions about your warranty, call:

BISSELL Consumer Services

1-800-237-7691

Monday - Friday 8 a.m. — 10 p.m. ET

Saturday 9 a.m. — 8 p.m. ET

Or write:

BISSELL Homecare, Inc.

PO Box 3606

Grand Rapids MI 49501

ATTN: Consumer Services

Or visit the BISSELL website - www.bissell.com

When contacting BISSELL, have model number of cleaner available.

Please record your Model Number: ___________________

Please record your Purchase Date: ___________________

NOTE: Please keep your original sales receipt. It

provides proof of purchase date in the event of a

warranty claim. See Warranty on page 19 for details.

BISSELL consumer services

www.bissell.com 800.237.7691

20

Registering is quick, easy and offers you benefits over the lifetime of your product.

You’ll receive:

BISSELL Rewards Points

Automatically earn points for discounts and free shipping on future purchases.

Faster Service

Supplying your information now saves you time should you need to contact us with

questions regarding your product.

Product Support Reminders and Alerts

We’ll contact you with any important product maintenance reminders and alerts.

Special Promotions

Optional: Register your email to receive notice of offers, contests, cleaning tips and more!

Visit www.bissell.com/registration now!

Don't forget to register your product!