Bosch Security Systems ZIGB01 Wireless TriTech Motion Detector for the ISW-ZDL1-WP11G and Wireless PIR Motion detector for the ISW-ZPR1-WP13 User Manual F01U284862 01a ISW ZDL1 WP11G Inguide indd
Bosch Security Systems, Inc. Wireless TriTech Motion Detector for the ISW-ZDL1-WP11G and Wireless PIR Motion detector for the ISW-ZPR1-WP13 F01U284862 01a ISW ZDL1 WP11G Inguide indd
User Manual
© 2013 Bosch Security Systems, Inc. F.01U.284.862 | 01a | 2013.06 | 1
=
=
=
12
13
12
Green
Vert
Yellow
Jaune
Red
Rouge
en Installation and Operation Guide
TriTech motion detector
ISW-ZDL1-WP11G
132
51 mm
(2.0 in)
131 mm
(5.2 in)
67 mm
(2.6 in)
4
6x 1.5 V
Duracell MN1500 AA Alkaline
Panasonic AM-3PIX AA Alkaline
0°C to +49°C
(+32°F to +120°F)
2.2 - 2.7 m
(7.5 - 9 ft)
Pet friendly
Animaux acceptés
1 ≤ 45 kg (100 lbs)
2 ≤ 27 kg (60 lbs)
≤ 10
52 sec
+
AA
+
AA
+
AA
+
AA
AA
+
AA
+
AA
90 sec
8
11 12 80 sec 10 sec
13 14 15
<3 min
0 - 93% Non-Condensing humidity
6
5 sec
7
Refer to the instruction manual that came with the
control panel to complete the pairing process.
Reportez-vous aux instructions fournies avec le
panneau de commande pour terminer le processus
d’appariement
Optional mounting brackets / Support de
montage en option: B328, B335, B338
15 sec
10
9
92 sec
© 2013 Bosch Security Systems, Inc. 130 Perinton Parkway Fairport, NY 14450 F.01U.284.862 | 01a | 2013.06 | 2
Bosch Security Systems, Inc. product manufacturing dates
Use the serial number located on the product label and refer to the Bosch
Security Systems, Inc website at:
http://www.boschsecurity.com/datecodes/.
Copyright
This document is the intellectual property of
Bosch Security Systems, Inc. and is protected by copyright.
All rights reserved.
Trademarks
All hardware and software product names used in this document are likely to be
registered trademarks and must be treated
accordingly.
FCC
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful interfer-
ence, and (2) this device must accept any interference received, including
interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instruc-
tions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installa-
tion. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the
following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help
IC
This device complies with Industry Canada licence-exempt RSS standard(s).
Operation is subject to the following two conditions: (1) this device may not
cause interference, and (2) this device must accept any interference, including
interference that may cause undesired operation of the device.
Le présent appareil est conforme aux CNR d’Industrie Canada applicables
aux appareils radio exempts de licence. L’exploitation est autorisée aux deux
conditions suivantes : (1) l’appareil ne doit pas produire de brouillage, et (2)
l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi,
même si le brouillage est susceptible d’en compromettre le fonctionnement.
Under Industry Canada regulations, this radio transmitter may only operate
using an antenna of a type and maximum (or lesser) gain approved for the
transmitter by Industry Canada.
To reduce potential radio interference to other users, the antenna type and
its gain should be so chosen that the equivalent isotropically radiated power
(e.i.r.p.) is not more than that necessary for successful communication.
Conformément à la réglementation d’Industrie Canada, le présent émetteur
radio peut fonctionner avec une antenne d’un type et d’un gain maximal (ou
inférieur) approuvé pour l’émetteur par Industrie Canada.
Dans le but de réduire les risques de brouillage radioélectrique à l’intention
des autres utilisateurs, il faut choisir le type d’antenne et son gain de sorte
que la puissance isotrope rayonnée équivalente (p.i.r.e.) ne dépasse pas
l’intensité nécessaire à l’établissement d’une communication satisfaisante.
AA
AA
AA AA
AA
+
AA
+
AA
AA
AA
AA AA
AA
12 3
AA
AA
AA AA
AA
AA
<4 sec
<3 min
1 2
1
AA
AA
AA AA
AA
+
AA
2
+
AA
+
AA
+
AA
+
AA
AA
+
AA
+
AA
3
Normal Operation
Fonctionnement Normal
Low Battery /
Trouble Condition
Batterie faible /
Condition de trouble
Reset
Réinitialiser 5
1
9
1