Bosch F01U087835 02 Easy Series 3 Ref Guide Quick Selection ( System Reference Guide) En US 2524758155

User Manual: Bosch Quick Selection Guide (- System Reference Guide) Easy Series Intrusion Control Panel

Open the PDF directly: View PDF .
Page Count: 126

Download
Open PDF In Browser	View PDF

Easy Series
ICP-EZM2

System Reference Guide

Easy Series

Table of Contents | en

Table of Contents
1

Overview

1.1

Installation Workflow

1.2

System Components and Wiring

1.3

Phone Menus

1.3.1

Installer Phone Menu

1.3.2

User Phone Menu

System Installation and Configuration

2.1

Plan the Installation

2.2

Install System Components

2.2.1

Install the wLSN Hub

2.2.2

Install the Control Panel Enclosure

2.2.3

Install the Control Center

2.2.4

Route Power-limited Wiring

2.2.5

Install the ITS-DX4020-G Communicator and Antenna

2.2.6

Install the DX2010 Input Expander

2.2.7

Connect the Conettix DX4020 Network Interface Module

2.2.8

Connect Supervised Points

2.3

Apply System Power

2.4

Initial System Startup

2.5

Perform the RFSS Site Test using the wLSN Installation Tool

2.5.1

Prepare the wLSN Hub for Site Testing and RFSS Mode

2.5.2

wLSN Installation Tool Mode 1

2.5.3

wLSN Installation Tool Mode 2

2.5.4

wLSN Installation Tool Mode 3

2.6

Install wLSN Devices

2.7

Configure the System from the Installer Phone Menu

2.7.1

Upgrade the Control Panel (Optional)

2.7.2

Initiate a Phone Session from the Control Panel

2.7.3

Configure Required Control Panel Settings

2.7.4

Discover Wireless Devices

2.7.5

Add Users, Tokens, and Key Fobs

2.8

Configure the ITS-DX4020-G Communicator

2.8.1

Configure the Control Panel for Cellular Communication

2.8.2

Configure the ITS-DX4020-G

2.8.3

Test ITS-DX4020-G Communications

Point Expansion

3.1

Perform a RFSS Site Test with the Hub and the Device

3.2

Establishing the Wireless Network and Configuring Wireless Devices

3.2.1

Discover a New System

3.2.2

Establish and Configure the Wireless Network

3.2.3

Configure Devices

3.3

Wireless Maintenance

3.3.1

Wireless Configuration Menu

3.3.2

Assigning Points 1 to 8 as Wireless Points

Bosch Security Systems, Inc.

System Reference Guide

F01U087835 | 02 | 2008.10

en | Table of Contents

Easy Series

3.3.3

Recovering the Wireless Network

3.3.4

Wireless System Messages

Programming Access Options

4.1

System Access by Phone

4.2

RPS

4.2.1

RPS Connection Methods

4.3

Programming Keys

Programming

5.1

Basic Programming

5.1.1

Enter Basic Programming

5.1.2

Points

5.1.3

Report Configuration

5.1.4

Outputs

5.2

Expert Programming

5.2.1

ROM Firmware Version Items

5.2.2

System Programming Items

5.2.3

Communicator Programming Items

5.2.4

RPS Configuration Items

5.2.5

Route Reporting Options

5.2.6

Point Programming Items

5.2.7

Output Programming Items

5.2.8

Control Center Programming Items

5.2.9

User Programming Items

5.2.10

Factory Default

5.3

Exit Programming

Control Panel Event Codes (SIA and Contact ID)

Default the System

7.1

Default the Control Panel and the wLSN Hub

7.2

Default wLSN Devices

System Test and Maintenance

8.1

Test the System

8.2

Maintain the System

8.3

Installer History Event Announcements

8.4

Event Messages

ITS-DX4020-G Communicator Configuration

9.1

ITS-DX4020-G Communicator Overview

9.2

Short Message Service (SMS) Configuration

9.3

Accessing the User Interface and Logging On Using USB

9.3.1

Downloading the ITS-DX4020-G USB Driver

9.3.2

Installing the ITS-DX4020-G USB Driver

9.3.3

USB Main Menu

F01U087835 | 02 | 2008.10

System Reference Guide

Bosch Security Systems, Inc.

Easy Series

Table of Contents | en

9.3.4

USB Option Menu

9.4

Upgrading the ITS-DX4020-G Software

9.4.1

Downloading the Latest Software

9.4.2

Installing the Software with Hyper Terminal

9.4.3

Installing the Software with Tera Term

Device Specifications and Overview

10.1

Control Panel

10.1.1

Standby Battery Calculation

10.2

Control Center

10.3

DX2010 Input Expander

10.4

Conettix DX4020 Network Interface Module

10.5

ITS-DX4020-G Communicator

10.6

wLSN Installation Tool

10.7

wLSN Hub

10.8

wLSN PIR and Dual Motion Detectors

10.9

wLSN Door-Window Contact

10.10

wLSN Recessed Door-Window Contact

10.11

wLSN Mini Door-Window Contact

10.12

wLSN Inertia Detector

10.13

wLSN Key Fob

10.14

wLSN Relay Module

10.15

wLSN Indoor Siren

10.16

wLSN Outdoor Siren

10.17

wLSN Smoke and Heat Detectors

10.18

wLSN Glassbreak Detector

10.19

wLSN Water Sensor/Low-temperature Sensor

100

Programming Details and Defaults

102

11.1

Programming Item Programming Details

102

11.2

Country Codes

107

11.3

Country Code Specific Default Programming Codes

108

Agency Approvals and Requirements

112

12.1

Certifications and Approvals

112

12.2

FCC

113

12.3

Industry Canada

114

12.4

SIA

114

12.5

Underwriters Laboratories (UL)

116

12.6

PD6662 and DD243 Requirements

118

12.7

EN50131 Requirements

119

12.8

INCERT

120

12.9

cUL

120

12.10

NF A2P

120

Bosch Security Systems, Inc.

System Reference Guide

F01U087835 | 02 | 2008.10

en | Overview

Easy Series

Overview
This document contains instructions for a trained installer to properly install, configure, and
operate the Easy Series control panel, and all optional peripheral devices.
You will install and configure the system using the figures starting in Section 1.2 System
Components and Wiring, page 6 and the information in Section 2 System Installation and
Configuration, page 12. The sections following Sections 1 and 2 provide supporting details for
installation, configuration, testing, and support.

1.1

Installation Workflow
To properly install, configure, and test the system, use the following workflow:

Step
1. Plan the Installation

Description
Identify suitable locations for system component in the installation

Page
Page 12

2. Install the Hardware
3. Perform RFSS Site Test
4. Configure the System

site.
Install all system components.
Perform radio frequency signal strength (RFSS) test.
Enroll wireless devices into the system, perform basic programming

Page 13
Page 18
Page 22

5. Program the System
6. Test the System

for the system, and add users to the system.
Update the system with expert programming.
Page 33
Perform a full system test. Ensure that the central monitoring station Page 61
received test reports.

Table 1.1 Installation Workflow

1.2

System Components and Wiring
Refer to Figure 1.1 through Figure 1.3 for overviews of the system components and wiring.
1

IUI-EZ1
+
R
Y
G
B

ISW-BHB1-WX
R
Y
G
B

DX2010

(+) (-)

(-)

R
Y
G
B

ICP-EZPS

(+)

11
9

DX4020

6
R
Y
G
B

(+)

(+)
(-)

(+) (-)

8
5

(+) (-) (+) (-) (+) (-)

ITS-DX4020-G
R
Y
G
B
T
T

Figure 1.1 System Component Wiring Overview

F01U087835 | 02 | 2008.10

System Reference Guide

Bosch Security Systems, Inc.

Easy Series

Callouts for Figure 1.2, Page 8
1 Control Center

Overview | en

Mount within 3 m of control panel, Use CAT5 cable (twisted pair) for audio
bus, Set data bus address (1 - 4), up to 4 controls max

wLSN Hub

S1
1
9
9

S2
0
2
8

DX2010 Point Expander

S3
0
= Normal Operation
0
= RFSS Mode
7
= Default Hub (refer to Page 60)
Data Bus Adr 102: Points 9 - 16
Data Bus Adr 103: Points 17 - 24
Data Bus Adr 104: Points 25 - 32

DX4020 Network Interface Module Data Bus Adr 134

1 - On
2 - Off

5
6

ITS-DX4020-G
Supervised Points (single EOL)

Data Bus Adr 134 (Fixed)

Supervised Points (dual EOL)

Normally closed (2.2k Ω)

Keyswitch Options (single and dual EOL) ((2.2k Ω)
Prog Output (PO) 1 Options
Switched 12v Switched Ground

10 Prog Outputs 2 - 4

Normally open and normally closed options (2.2k Ω)

Dry Contact

NF A2P requires that sirens have a backup battery. When this siren
requires a 14,1V to 14,4V supply, use the optional board EZPS-FRA or the
auxiliary power supply IPP-PSU-2A5. Set the output as interior burglary

11 2-wire Smoke Detector Option
12 4-wire Smoke Detector Option

alarm.
EOL resistor (P/N: 25899) required.
EOL resistor (P/N: 25899) and Bosch EOL relay module required

Note: The system uses a 12 VDC battery, connected as shown.

Bosch Security Systems, Inc.

System Reference Guide

F01U087835 | 02 | 2008.10

en | Overview

Easy Series

Figure 1.2 Overview of the System Component Location for the ICP-EZM2-R Enclosure

Figure 1.3 Overview of the System Component Location for the ICP-EZM2-EU Enclosure

F01U087835 | 02 | 2008.10

System Reference Guide

Bosch Security Systems, Inc.

Easy Series

Overview | en

Callouts for Figure 1.2 Page 8 and Figure 1.3, Page 8
1
Port for ICP-EZRU-V3 ROM Update Key and Programming Key
2
Enclosure Cover and Wall Tamper Switch
3
Ground connection
4

Connect ground wire from enclosure to enclosure door.
Module mounting location

ITS-DX4020-G shown.
Module mounting location

DX2010 shown.
System test button
When the system is completely installed and programmed, press the system test button to start a full system

7
8

test.
Port for ICP-EZVM voice module
Enclosure terminal cover (ICP-EZM2-R Enclosure only)
Shipped in hardware bag. Install over terminals when power supply wiring is completed.

Bosch Security Systems, Inc.

System Reference Guide

F01U087835 | 02 | 2008.10

en | Overview

Easy Series

1.3

Phone Menus

1.3.1

Installer Phone Menu
1 Warning device test
1 Set date and time
Installer
Passcode

2 Battery test

2 Full system test

3 Communication test

3 System test menu

4 Control center test
1 Most recent events
2 Events by date

4 Event history
1
System
Maintenance

5 Point test
6 Operate Outputs

3 Last alarm event

# Exit

4 Last 10 events
# Exit
1 Replace a device
5 Reset system

2 Add a device
3 Delete a device
4 Transfer wireless data
(control panel-to-hub)

6 Wireless configuration

5 Transfer wireless data
(hub-to-control panel)

# Exit

6 Erase and discover
# Exit

1 Change installer passcode
2
User Menu

2 Change master user (User 1) passcode

1 Record point description

# Exit user menu
2 Set point type
1 Points

# Exit
1 Enter account number

2 Configure report destinations

Basic
Programming

2 Report configuration

3 Remote programming success
# Exit
1 Select output function

3 Outputs
# Exit
4 Country code
# Exit
4
Expert
Programming

Enter programming item, enter selection.
1 Talk to person at control center

2 Listen to person at control center

Two-Way
Voice Session

# Exit
1 Record site description

2 Record Call for Service message

Custom
Messages

# Exit
1 Send data from key to control panel

7
Programming
Key

2 Send data from control panel to key
# Exit

# Exit

= The system’s arming status (on or off) and Expert Programming Item Number 142 setting of (0 or 1) determines the availability of
these menu items. Refer to Section 5.2.2 System Programming Items, Page 43.
When recording any description (point, output, user, or custom message), do not press any buttons on your phone until
prompted by the system.

F01U087835 | 02 | 2008.10

System Reference Guide

Bosch Security Systems, Inc.

Easy Series

Overview | en

1.3.2

User Phone Menu

Enter user
passcode1

Two-Way
Voice Session

Phone
Menu

Turn system on and stay inside
Turn system on and leave

Turn System On or Off
Only use this option
on non-UL systems.

1
2

Turn on custom protection
To hear this option, custom protection must be
enabled.

Exit

Talk to person at control center

Listen to person at control center

End voice session

Set date and time

Full system test

System test menu

3
System
Maintenance2

4
User Menu3

}

1
2

The voice session only lasts 90 seconds.
To reset the timer, press [1] on the phone during talk mode,
or [2] during listen mode.

Warning device test

Battery test

Communication test

Control center test

Point test

Operate outputs
OR
4
Expert Programming (Enable Installer Access)

Exit system test menu

Most recent events

Events by date

Last alarm event

Event history

Reset system

Exit

}

Add new user

Change user

Delete user

Exit

Last 10 events

Exit

To add or change a user:

Change token

Record description

Change passcode

Change key fob

Exit

Only the Master User can
access the full User Menu.
Users 2 to 21 can only change
their own passcode.
5
Operate Outputs
To turn an output on or off, press the
corresponding number key on the phone.
#
Exit
End phone session.

Only a user passcode (Users 1 to 21) can access the User Menu.

If the system is on, the System Maintenance option is not available.

Only the master user can add, change, or delete users. Users 2 to 21 can only change their own passcodes. User voice descriptions are

stored in the voice module and are not transferred to the control panel with programming data.
4

Option 6 allows the master user (User 1) to enable the Installer Passcode. Refer to Expert Programming Item Number 142 in

Section 5.2.2 System Programming Items, Page 43.
Availability of the menu items shown above depends on the system's status.
When recording any description (point, output, user, or custom message), do not press any buttons on your phone until prompted
by the system.

Bosch Security Systems, Inc.

System Reference Guide

F01U087835 | 02 | 2008.10

en | System Installation and Configuration

Easy Series

System Installation and Configuration

2.1

Plan the Installation
When planning the installation, identify suitable locations for the control panel, control
center, hub, and wireless devices before installing any system components. When identifying
these locations, ensure that the following considerations are addressed.

Task

Considerations

1. Identify the location for

–

the control panel.

–

Only use authorized service personnel to install this system.
Plan to install the control panel in a centrally located room that is near the AC
Power MAINS.

–

Plan to install the control panel in a location with a good earth ground.

–

Because the control panel is permanently connected equipment, a readily
accessible disconnect device must be included into the building installation
wiring.

2. Test for GSM signal

Use your cell phone to identify an area with good GSM signal strength by monitoring

strength.

the signal strength on your mobile phone.
If the intended location of the control panel has poor GSM signal strength, find a
new location for the control panel.

3. Identify the location for

Plan to install the control center near the primary entry and exit door.

the control center.
4. Identify the location for

Plan to install the wLSN Hub in a location with good radio-frequency (RF)

the wLSN Hub.

characteristics and within 100 m of the control panel.

5. Identify the location for

–

the wLSN devices.

wLSN devices are intended only for indoor, dry applications. Avoid installing the
devices where excessive humidity or moisture, or temperatures outside of the
acceptable operating range, exist.

–

Mount wLSN devices on flat, rigid surfaces. For more information, refer to each
device's installation instructions.

–

Avoid mounting wLSN devices in areas with large metallic objects, electrical
panels or electric motors. They might reduce the (RF) range of a wLSN device.

Table 2.1 Installation Considerations

F01U087835 | 02 | 2008.10

System Reference Guide

Bosch Security Systems, Inc.

Easy Series

System Installation and Configuration | en

2.2

Install System Components
NOTICE!
–

Use proper anchor and screw sets when installing the enclosure on non-load-bearing

–

Follow anti-static procedures when handling the control panel board. Touch the earth

surfaces, such as drywall.

i
i
2.2.1

ground terminal on the control panel board to discharge any static charge before working
on the control panel board.
–

If you install more than one control center, mount them at least 1.2 m apart.

–

Do not install the wLSN Hub within 15 cm (6 in) of the control centers metal enclosure.

NOTICE!
Refer to Figure 1.2, Page 8 or Figure 1.3, Page 8 throughout this section for the location to
install each of the hardware components in the enclosure.

Install the wLSN Hub
1.
2.

Separate the wLSN Hub from its base.
Set the wLSN Hub's rotary switches to enable RFSS mode: S1 = 9, S2 = 2, S3 = 0.
This is the setting required for the RFSS site test. Refer to Figure 1.1, Page 6.

Connect the wLSN Hub's data bus to the control panel's data bus. The wLSN Hub's
terminal block is removable.
–

Wire Gauge: 0.14 mm to 1.5 mm (18 AWG to 24 AWG)

–

Wire Length (sLSN Hub to control panel): <= 100 m

Reconnect the wLSN Hub and base, and then lock the wLSN Hub.

Mount the wLSN Hub temporarily in the desired location. You might need to relocate the
wLSN Hub if it does not pass RFSS testing.

2.2.2

Install the Control Panel Enclosure
1.

Remove the desired knockouts from the control panel enclosure and optional mounting
skirt.

Attach the optional mounting skirt to the enclosure.

Route the wires through the desired knockouts.

Mount the enclosure to the desired surface. Use proper anchor and screw sets when you
install the enclosure on non-load-bearing surfaces, such as drywall.

Bosch Security Systems, Inc.

System Reference Guide

F01U087835 | 02 | 2008.10

en | System Installation and Configuration

2.2.3

Easy Series

Install the Control Center
1.
2.

Unlock the control center and separate it from the base.
If you install more than one control center, each control center must have a unique
address. Valid address are 1 to 4. Refer to Figure 2.1 for the location of the address
switch.

Figure 2.1 Control Center Address Switch

Control Center’s front cover

Address switch’s default settings
3.

Mount the control center base to the desired surface using the appropriate mounting
holes. Use the built-in level in the control center base as a guide.

NOTICE!
Mount the base to a non-metallic surface that is near the primary entry/exit door.

If you install more than one control center, ensure that there is at least 1.2 m between each
control center.
Avoid mounting the control center near existing phone lines.
Avoid mounting the control center near other electronic devices.
4.

Connect the control center data bus terminals to the control panel data bus terminals.
Refer to Figure 1.1, Page 6.

Connect the control center audio bus terminals to the control panel audio bus terminals.
Twisted pair wiring is recommended for audio bus terminals. Refer to Figure 1.1, Page 6.

Reconnect the control center and base, and then lock the control center.

Refer to Section Control Center Display States, Page 75 for an overview of the various control
center display states.

F01U087835 | 02 | 2008.10

System Reference Guide

Bosch Security Systems, Inc.

Easy Series

System Installation and Configuration | en

2.2.4

Route Power-limited Wiring
All wiring except primary AC power and standby battery is power-limited. Separate primary
AC power and standby battery wires from other wires by at least 6.4 mm (¼ in), and secure to
enclosure to prevent movement. Primary AC power and standby battery wiring cannot share
the same conduit, conduit fittings, or conduit knockouts with any other wiring. Refer to
Figure 2.2, Page 15.

Figure 2.2 Power-limited Wire Routing

2.2.5

Install the ITS-DX4020-G Communicator and Antenna
The ITS-DX4020-G is powered from the bus.

NOTICE!
When using the ITS-DX4020-G GSM channel for communications, do not permanently connect
a telephone to the Easy Series house phone terminals.

Refer to Figure 1.1, Page 6 for wiring instructions.
1.

Install the ITS-DX4020-G SIM card.
a) Hold the ITS-DX4020-G communicator in the orientation shown in Figure 9.1, Page 62.
b) Slide the SIM cardholder door upward to unlock it, and then open the door.
c) Hold the SIM card in the orientation shown in Figure 9.1, Page 62, and then Insert the
SIM card into the cardholder door; the notched edge is away from the hinge.
d) Close the cardholder door, and then slide the door downward to lock it.

Mount the communicator into the control panel's enclosure using the side wall mounting
location.

Place the magnetic antenna on the panel enclosure (on top recommended for vertical
polarization). The antenna must be placed on a metal surface for proper operation.

Connect the antenna cable to the communicator.

Connect the audio terminals on the ITS-DX4020-G to the control panel’s inside phone
terminal block.

Connect the communicator option bus molex connector to the to the communicator and
connect the bus wires to the option bus terminals on the control panel. If preferred, the
terminal screws on the communicator can be used instead of the molex connection.

Install the configuration jumper on the CONFIG MODE (J200) pins. Refer to Figure 9.1,
Page 62 for the jumper location.

Bosch Security Systems, Inc.

System Reference Guide

F01U087835 | 02 | 2008.10

en | System Installation and Configuration

2.2.6

Easy Series

Install the DX2010 Input Expander
The control panel supports up to three DX2010 Input Expanders for Points 9 to 32.
Refer to the DX2010 Installation Instructions (P/N: 49533) for more information.
1.
2.

Set the DX2010's DIP switches.
Mount the DX2010 into the control panel's enclosure (back wall or either side wall), or
other suitable enclosure.

Connect the DX2010 to the control panel. Refer to Figure 1.1, Page 6.
Connect a wire jumper to the TMPR and COM terminals to disable the DX2010's tamper
input. For point wiring options, refer to Section 2.2.8 Connect Supervised Points, Page 16.
To disable the tamper input on the DX2010, connect a wire jumper between the TMPR
and COM terminals.

i
2.2.7

NOTICE!
In an NF A2P certified installation, mount the DX2010 module on one side of the panel
housing, or on one side of the auxiliary power supply IPP-PSU-2A5).

Connect the Conettix DX4020 Network Interface Module
The control panel supports one DX4020 for wired network communication.
Refer to the DX4020 Installation Instructions (P/N: F01U045288) for more information.
1.

Set the DX4020's DIP switches to Address 134 for network communication.

Mount the DX4020 into the control panel's enclosure using the back wall or side wall
mounting location.

2.2.8

Connect the DX4020 to the control panel. Refer to Figure 1.1, Page 6.

Connect Supervised Points
For wiring diagrams, refer to Figure 1.1, Page 6.
Fire Point Wiring
Supervised Point 1 supports two- and four-wire smoke detectors.
Supervised Points 2 to 32 support only four-wire smoke detectors.
To program supervised points as fire points, refer to Section 5.1.2 Points, page 39.
For intrusion point configuration, refer to Section Intrusion Point Wiring, Page 16.
When using an output to supply power to a four-wire smoke detector, program the output
function for System Reset. Refer to Section 5.1.4 Outputs, page 41.
Intrusion Point Wiring
You can wire Supervised Points 1 to 32 as wired or wireless intrusion points.
To program Supervised Points 1 to 32 as intrusion points, refer to Section 5.1.2 Points,
page 39.

F01U087835 | 02 | 2008.10

System Reference Guide

Bosch Security Systems, Inc.

Easy Series

System Installation and Configuration | en

2.3

Apply System Power
NOTICE!
Because the control panel is permanently connected equipment, a readily accessible

disconnect device must be included into the building installation wiring.
An external earth ground is required to ensure safe and proper system operation. Failure to
ground the system can cause personal injury and degraded system performance, such as
problems with tokens or noise on the control center.
1.

Connect battery power to the control panel. Refer to Figure 1.1, Page 6.

Use a cable tie to secure the incoming AC wires to the enclosure, where required. Refer
to Figure 2.3, Page 17.

Figure 2.3 Cable tie for MAINS to Power Supply

Bosch Security Systems, Inc.

Place the terminal cover over the power supply terminals.

System Reference Guide

F01U087835 | 02 | 2008.10

en | System Installation and Configuration

2.4

Easy Series

Initial System Startup
1.

Apply AC power to the system.

Refer to Table 2.2 for the Initial System Startup sequence.

Stage

Time Interval

Control Center

wLSN Hub

0-15 sec

Intermittent flashing green icon

15-45 sec

Flashing amber circle

45-75 sec

Single rotating amber segment

75 sec

Solid green circle

LED on steady

Table 2.2 Initial System Startup Sequence (No wLSN devices discovered)

2.5

Perform the RFSS Site Test using the wLSN Installation Tool
The wLSN Installation Tool communicates signal strength levels, noise levels, signal-to-noise
ratio (SNR), and packet success rates. Use it to determine the best locations for wLSN device
installation.
NOTICE!

i
!

Before permanently installing any wLSN device, verify that the radio-frequency signal strength
(RFSS) between the planned device location and the planned wLSN Hub location is
acceptable.
CAUTION!
If you have wireless devices that you will not immediately install, reinsert the battery tabs or
remove the batteries to prevent battery depletion.

NOTICE!

You can perform the RFSS site test using the wLSN Hub and the specific device you wish to
test. However, you must use the Installation Tool with the wLSN Smoke Detector. You cannot
determine RFSS with the detector itself. Refer to Section 3.1 Perform a RFSS Site Test with the
Hub and the Device, page 28 for instructions.

F01U087835 | 02 | 2008.10

System Reference Guide

Bosch Security Systems, Inc.

Easy Series

System Installation and Configuration | en

2.5.1

Prepare the wLSN Hub for Site Testing and RFSS Mode
1.

Unlock the wLSN Hub and separate it from its base.

Set Switch S1 to 9 and Switch S2 to 2 to enable RFSS mode. This disables normal
operation. Refer to Figure 1.1, Page 6.

Set Switch S3 to a value of 0 to 4, based upon the RF power level or EN50131 security
grade you wish to use. Refer to Table 2.3.

Switch 3 Setting

RF Power (EN50131 Security Grade

Maximum power

3 dB lower than maximum (Security Grade 1)

6 dB lower than maximum (Security Grade 2)

9 dB lower than maximum (Security Grade 3)

12 dB lower than maximum (Security Grade 4)
Table 2.3

wLSN Hub RF Power/EN Settings

Refer to individual device's specification for their EN50131 classification.

NOTICE!
You must test the devices at the same EN50131 Security Grade at which the control panel
discovers the devices.

Find a suitable location for the hub base and apply power by either connecting it to the
control panel (refer to the control panel's installation instructions), or temporarily
connecting a 9 VDC to 12 VDC battery.

2.5.2

Reconnect the wLSN Hub and base, and then lock the wLSN Hub.

wLSN Installation Tool Mode 1
Mode 1 identifies if a device location has acceptable or unacceptable RFSS.
To test the wireless devices with the Installation Tool in Mode 1:
1.

Verify that the wLSN Hub rotary switch is set to S1 = 9, S2 = 2, S3 = 0. Refer to Figure 1.1,
Page 6. The wLSN Hub's LED flashes slowly.

Go to the first device location, and then press and hold [*][#] on the Installation Tool for
2 sec.

3.
4.

Press [1] for Mode 1.
Place the Installation Tool in an upright position at the first device location, or hold it in
the location, if necessary.

Wait 10 sec and then review the display.

–

Acceptable RFSS Display:

–
M

Unacceptable RFSS Display:
O

If the location tests:
–

OK: Confirm that the location is OK by testing it with the actual wireless device for this
location.

–

Bosch Security Systems, Inc.

Not OK: Test a different location.

System Reference Guide

F01U087835 | 02 | 2008.10

en | System Installation and Configuration

2.5.3

Easy Series

wLSN Installation Tool Mode 2
To test the wireless devices with the Installation Tool in Mode 2:
1.

Verify that the wLSN Hub rotary switch is set to S1 = 9, S2 = 2, S3 = 0. Refer to Figure 1.1,
Page 6. The wLSN Hub's LED flashes slowly.

Go to the first device location, and then press and hold [*][#] on the Installation Tool for
2 sec.

3.
4.

Press [2] for Mode 2.
Place the Installation Tool in an upright position at the first device location, or hold it in
the location, if necessary.

5.
M

Wait 10 sec and then review the display.
O

:
P

The Mode 2 display shows power bars on the left and the number of packets received on the
right. The bars indicate the signal strength. The Installation Tool shows the number of packets
received: 1, 2, or 3.
Power Bars

Signal to Noise Ratio

Packets

Signal Strength

< 9 dB

≤2

Unacceptable

9 dB

≥2

Marginal (not recommended)

13 dB

≥2

Acceptable

16 dB

≥2

Good

20 dB

≥2

Very good

22 dB

≥2

Excellent

Table 2.4 Mode 2 Display Data

If the location tests:
–

OK: Confirm that the location is OK by testing it with the actual wireless device for this
location.

–

F01U087835 | 02 | 2008.10

Not OK: Test a different location.

System Reference Guide

Bosch Security Systems, Inc.

Easy Series

2.5.4

System Installation and Configuration | en

wLSN Installation Tool Mode 3
When you perform the RFSS Site Test record the highest and lowest SNR readings because
you may need to compare them.
If the results for SNR fluctuate significantly, the location is:
–

OK if you subtract the dB difference between the highest (H) result and the lowest (L)
result, and the number equals more than 13 dB. Confirm the location is OK by testing
with the actual wireless device for this location. (L - (H - L) ≥ 13 dB = OK

–

Not OK if you subtract the dB difference between the highest (H) result and the lowest
(L) result and the number equals less than 13 dB. In this case, select a new location to
test. (L - (H - L) ≤ 13 dB = Not OK)

To test the wireless devices with the Installation Tool in Mode 3:
1.

Verify that the wLSN Hub rotary switch is set to S1 = 9, S2 = 2, S3 = 0. Refer to Figure 1.1,
Page 6. The wLSN Hub's LED flashes slowly.

Go to the first device location, and then press and hold [*][#] on the Installation Tool for
2 sec.

3.
4.

Press [3] for Mode 3.
Place the Installation Tool in an upright position at the first device location, or hold it in
the location, if necessary.

Wait 10 sec and then review the display.
In the Mode 3 display, "SNR yy" refers to the signal to noise ratio in dB and "x" is the
RFSS value in dBm.
The Mode 3 display shows the signal to noise ratio (SNR) at the test spot. S refers to the
signal strength of the incoming message from the wLSN Hub to the Installation Tool. N
refers to the ambient noise level that exists at the location. The signal must be greater
than the noise (S>N). The higher the SNR, the stronger the location's signal at that
location. Dashes, appearing on both the S and N lines, indicate unacceptable signal
strength.

6.
7.

Note the readings for the location, especially the SNR values.
Refer to Table 2.5 to interpret the results based on the lowest and highest readings.
If one or more of the results for SNR falls below 13 dB, the location is Not OK.

Signal to Noise Ratio

Signal Strength

< 9 dB

Unacceptable

9 dB

Marginal (not recommended)

13 dB

Acceptable

16 dB

Good

20 dB

Very good

22 dB

Excellent
Table 2.5

Signal to Noise Ratio Data

If the location tests:
–

OK: Confirm that the location is OK by testing it with the actual wireless device for this
location.

–

Bosch Security Systems, Inc.

Not OK: Test a different location.

System Reference Guide

F01U087835 | 02 | 2008.10

en | System Installation and Configuration

2.6

Easy Series

Install wLSN Devices
1.

If RFSS is OK:
–

Install the device's base and continue to the next location.

If RFSS is Not OK:

–

Determine what is preventing acceptable RFSS and re-test.

–

Move the device to a new location and re-test, or

–

Move the wLSN Hub to a new location and re-test.

Repeat Steps 5 through 10 in Section 2.5 Perform the RFSS Site Test using the wLSN
Installation Tool on Page 18 until all locations are tested and all bases installed.

Press and hold [*][#] to exit from the test mode.
The Installation Tool powers down from the main menu 30 sec after the last key press.

2.7

Remove power from the system.

Set the wLSN Hub's rotary switches to: S1 = 1, S2 = 0, S3 = 0.

Reapply power to the system.

Configure the System from the Installer Phone Menu

i
2.7.1

NOTICE!
You can configure a control panel using pre-configured program data stored on a
programming key. For more information, refer to Section 4.3 Programming Keys, page 36.

Upgrade the Control Panel (Optional)
Insert the ICP-EZRU-V3 ROM update key.
The upgrade is complete (after 5 to 10 min), when the green (√) LED on the control panel
flashes. Remove the green upgrade programming key.

2.7.2

Initiate a Phone Session from the Control Panel
1.

Connect a phone set to the test posts or to the phone terminals. Refer to Figure 1.1,
Page 6.

Press and hold the System Test button for approximately 15 sec. Figure 1.2, Page 8 for
the location of the Test button.

When prompted, use the phone set to enter the installer passcode (default is 5432[11])
for the Installer Menu, or the master user passcode (default is 1234[55]) for the User
Menu. For the following two procedures, enter the installer passcode.

i
2.7.3

NOTICE!
For more information on default passcodes, refer to Section 4.1 System Access by Phone,
page 33.

Configure Required Control Panel Settings
1.

From the Installer menu, if prompted to set the panel date and time, press [1][1]. When
finished following the prompts, press [#][#] to return to the Installer Menu.

If prompted to set the Country Code, press [3][4]. Refer to Section 11.2 Country Codes,
page 107 for the appropriate Country Code. When finished following the prompts, press
[#] to return to the Installer Menu.

F01U087835 | 02 | 2008.10

System Reference Guide

Bosch Security Systems, Inc.

Easy Series

System Installation and Configuration | en

2.7.4

Discover Wireless Devices
Discovery is the process through which the wLSN Hub identifies and includes new devices
into a system.
1.

From the Installer Menu (refer to Section 2.7.2 Initiate a Phone Session from the Control
Panel, page 22), press [1][6] to start the Discovery Process.

Mask all motion detectors. (The optional ISW-BMASK-10 may be used.)

When the system announces, "Install all batteries," install the batteries or remove the
battery tabs from the wireless devices.

Press [1] to continue. The system then says, "Discovering devices, please wait."
During this time, the system finds all the undiscovered wireless devices. This process
takes approximately 6 min.

NOTICE!
Point numbers are assigned to wireless devices in the order that the devices first

communicate to the system (tampered, faulted, low battery). If specific point numbers are
preferred for wireless devices, ensure that the wireless devices communicate in the
appropriate order. Otherwise, the system assigns the lowest available point number to the
first tested wireless device. With motion detectors, unmask only the detector you want to
test.
5.

The system announces, "Wireless devices: xx. Test all points."
"xx" = the number of wireless devices discovered, but not yet tested.

Test each point. If specific point numbers are preferred, test points in the appropriate
order.
Refer to Table 2.6 for instructions on testing each wireless device.

Device

To Test

Motion Detectors

Walk across the detector's coverage pattern.

Smoke Detector

Press and release the detector's test button, or blow smoke into the detector's chamber
to cause an alarm. Restore the alarm.

Relay Module

Input and Output: Fault and restore the supervised loop.
Output Only: Tamper the device.

Inertia Detector

Magnetic Switch: Open and then close the switch.
Inertia Only: Cause an alarm and then restore the alarm1, or tamper the detector.3

Glass Break Detector

Cause an alarm and then restore the alarm, or tamper the detector.3

Mini Door/Window

Open and then close the magnetic switch.

Contact
Recessed Door/Window
Contact
Door/Window Contact

Open and then close the magnetic switch, or fault and then restore the supervised loop.
Perform both tests only if both the magnetic switch and supervised loop are used.

Indoor Siren

Tamper the device.

Outdoor Siren

Tamper the device. To configure the device, refer to Section 10.16 wLSN Outdoor Siren,
page 91.

Bosch Security Systems, Inc.

System Reference Guide

F01U087835 | 02 | 2008.10

en | System Installation and Configuration

Easy Series

Device

To Test

Water Sensor/Low-

Water Sensor: Select one of the following methods:

temperature Sensor

–

Short the water probe pins for at least 5 sec.

–

Submerge the water probe in water for at least 5 sec.

Low-temperature Sensor: Short the "T" pads for at least 5 sec.
1

To test the inertia detector, create a shock to cause an inertia alarm, and then restore alarm.

To test the glass break detector, use a special tool to cause a glass break alarm, and then restore the alarm.

If you tamper the detector, the control panel enrolls the detector, but does not test it. You must create the appropriate alarm and

restore the alarm to test the detector.
Table 2.6 Wireless Device Test Procedures

After each successful point test, the system announces "Point xx was tested."
If you test a point and the system only announces "Point xx," the point number is assigned,
but has not been tested:
–

If you prefer specific point numbers, do not continue. Fix any issue with the device and
re-test until the system announces "Point xx was tested."

–

If you do not prefer specific point numbers, you can test them later through the Installer
Menu. When the system completes the testing, the system announces "Wireless devices
not configured."

2.7.5

The system says, "System test complete.”

Add Users, Tokens, and Key Fobs
1.

From the User Phone Menu (refer to Section 2.7.2 Initiate a Phone Session from the Control
Panel, page 22), press [4] to enter the User Menu.

From the User Phone Menu, press [4] to enter the User Menu.

Press [1] to add a new user. After you add a new user, you can also assign a token,
passcode, and key fobs to that user.

Repeat Step 4 to add more users.

Press [#] to return to the User Menu.

NOTICE!
If you plan to use a programming key to copy control panel data for back up or use on another
system, back up the data now. Refer to Section 4.3 Programming Keys, page 36.

F01U087835 | 02 | 2008.10

System Reference Guide

Bosch Security Systems, Inc.

Easy Series

System Installation and Configuration | en

2.8

Configure the ITS-DX4020-G Communicator

2.8.1

Configure the Control Panel for Cellular Communication

You must enabled GSM dialing, and set the format used and the destination IP address and
port number or phone number. You can also configure anti-replay and other parameters. To
do so:
1.
2.

Enable GSM dialing using Expert Programming Item 202.
For the primary and backup destinations, configure the control panel options as desired.
Refer to Table 2.7, Page 25 for an example of a typical configuration and the
corresponding Expert Programming Items.
Format

IP Address/Phone Number

Port

Anti-replay

Route 1 Primary (GPRS)

Network

192.168.121.195

7700

Item Number to Configure

211

206

241

289

Route 1 Backup (GSM)

Contact ID

1.585.223.4060

N/A

Item Number to Configure

212

207

Table 2.7

2.8.2

Example Configuration for Cellular Communications

Configure the ITS-DX4020-G
Ensure that the configuration jumper is installed on the CONFIG MODE (J200) pins.
Refer to Section 2.2.5 Install the ITS-DX4020-G Communicator and Antenna, page 15 for proper
installation.
1.

Observe the LEDs to check for signal strength. Refer to Table 2.8, Page 25. Refer to
Figure 9.1, Page 62 for LED locations.
LED State

Strength/Comments

STATUS CELL IP

AUDIO

SS1

SS2

SS3

BUS

Unacceptable—No reading available (modem is resetting or

⊗

Off

⊗

Attempting to register on the GSM network.

⊗

Flash

Off

⊗

Unacceptable: < -89 dBm.

⊗

Off

⊗

Acceptable: -89 dBm to -83 dBm.

⊗

Flash

Off

⊗

Good: -83 dBm to -77 dBm.

⊗

Off

⊗

Very good: -77 dBm to -69 dBm.

⊗

Flash

⊗

Excellent: > -69 dBm.

⊗

registering).

Key:

→ = Scrolling LEDs, from left to right. ⊗ = LED’s status does not matter.

Shifting flash = Every other LED flashes simultaneously, creating the shifting flash pattern.
Table 2.8

ITS-DX4020-G Signal Strength LEDs

Call the central monitoring station (CMS) and provide the account number (may be
known as NNC number at the CMS), and control panel polling rate.

Observe the BUS LED. The LED stays on steady when the communicator has permission
to be configured. Refer to Figure 9.1, Page 62 for LED locations. Refer to row 2 in
Table 2.9, Page 26.

Observe the SS1 LED to confirm the ITS-DX4020-G is registered and has sufficient signal
strength to configure it by SMS. The SS1 LED must be On to continue. Refer to
Figure 9.1, Page 62 for LED locations. Refer to Table 2.8, Page 25 for the LED states.

Use the SMS configuration template to send the SMS to the installed SIM card phone
number. For detailed SMS configuration information, refer to Section 9.2 Short Message
Service (SMS) Configuration, page 63.

Bosch Security Systems, Inc.

System Reference Guide

F01U087835 | 02 | 2008.10

en | System Installation and Configuration

Easy Series

Observe the LEDs to confirm that the communicator received a valid configuration SMS.
Valid SMS configurationsshould be received within 5 min. Refer to row 4 in Table 2.9,
Page 26.
LED State

State/Comments

STATUS

CELL IP

AUDIO

SS1

SS2

SS3

BUS

No control panel authorization received.

→

GSM Signal Strength

Off

Installer is authorized for Configuration

→

GSM Signal Strength

mode, or authorization is not required.

Received invalid SMS.

→

Flash

Received valid SMS authorizing

→

configuration.
Key:

→ = Scrolling LEDs, from left to right. ⊗ = LED’s status does not matter.

Shifting flash = Every other LED flashes simultaneously, creating the shifting flash pattern.
Table 2.9 Configuration Mode (J200 Jumper Installed) LED States

NOTICE!
If the LEDs indicate an invalid SMS, remove the configuration jumper and then repeat the

steps in Section 2.8.2 Configure the ITS-DX4020-G, page 25.
If the LEDs continue to indicate an invalid SMS, the SMS template might be incorrect. Confirm
the SMS template format and settings and try again, or use a USB connection to configure the
ITS-DX4020-G.
7.

Remove the configuration jumper. The communicator reboots.

Ensure that the ITS-DX4020-G can communicate with the D6600/DX6600i. Refer to
Table 2.10, Page 26.

CELL IP
Off
Flash
On

Status
ITS-DX4020-G is not connected to the GPRS network.
ITS-DX4020-G is connected to the GPRS network, but not connected to the Bosch receiver.
ITS-DX4020-G is connected to the Bosch receiver through the GPRS network.
Table 2.10 D6600 Connection Status

F01U087835 | 02 | 2008.10

System Reference Guide

Bosch Security Systems, Inc.

Easy Series

2.8.3

System Installation and Configuration | en

Test ITS-DX4020-G Communications
1.

Configure the control panel for cellular communication, if necessary. Refer to
Section 2.8.1 Configure the Control Panel for Cellular Communication, page 25.

Send a test alarm using the GPRS network route, and then verify receipt of the alarm at
the CMS.

For systems using a ITS-DX4020-G with Network as the Primary Format (GPRS) and
Contact ID or SIA as the Backup Format (GSM), program and use a Manual Communicator
Test using Programming Item Number 362 (refer to Section System Report and Restoral
Routing, page 51). Then, send a test report using the PTSN using GSM destination and
observe the LEDs. Refer to Section 2.8.3 Test ITS-DX4020-G Communications, page 27 for
configuration information. To use the Manual Communicator Test:
a) Set the Format for Route 2 Primary Destination (Programming Item Number 213) the
same as the Format for Route 1 Backup Destination (Programming Item Number 212)
b) Set the Route 2 Primary Destination (Programming Item Number 208) the same as the
Route 1 Backup Destination (Programming Item Number 207).
c) Set Programming Item Number 362 to 2 (Route 2 only).
d) Set Programming Item Number 202 to 1.

If incoming GSM calling is enabled, initiate a phone call into the control panel voice
menu.

Bosch Security Systems, Inc.

System Reference Guide

F01U087835 | 02 | 2008.10

en | Point Expansion

Easy Series

Point Expansion

3.1

Perform a RFSS Site Test with the Hub and the Device
You can use the wLSN Hub and the wLSN device to perform an RFSS site test, or use the
wLSN Installation Tool (refer to Section 2.5 Perform the RFSS Site Test using the wLSN
Installation Tool, page 18).
1.

Take the device being tested to its planned mounting location.

Remove and re-insert the device's batteries, then quickly press and release the tamper
switch button four times to enter RFSS mode.

Hold the device at the planned mounting location.

Determine if the RF signal strength is acceptable by observing the device's LED flash
pattern. The flash pattern appears for 10 min. Refer to Table 3.1, Page 28.

LED Flash Pattern
Flashes at 1 sec intervals

No packets received or unacceptable signal strength condition.

Flashes rapidly (0.2 sec intervals)

Acceptable signal strength.

Table 3.1 wLSN Device LED Flash Patterns in RFSS Mode

i
3.2

NOTICE!
To cause a device to exit RFSS mode, remove the device's batteries and re-insert them.
Devices automatically exit RFSS mode after 10 min of inactivity.

Establishing the Wireless Network and Configuring Wireless
Devices
In order for the wireless network to operate properly, the following process must occur as
shown below.
→

Inputs and
Outputs

Discover
Devices

→ Establish
Network

→

Configure
Network

→

Configure
Devices
→

F01U087835 | 02 | 2008.10

System Reference Guide

Key Fobs

Bosch Security Systems, Inc.

Easy Series

Point Expansion | en

3.2.1

Discover a New System
Discovery is the process through which the wireless hub identifies and includes new
(undiscovered) devices into the system.

NOTICE!
You can only perform the new system discovery process once. To update an existing wireless
system, refer to Section 3.3 Wireless Maintenance, Page 31.

There are two ways to start the discovery process on a new system: point test, and the
Wireless Configuration Menu: Point Test and the Wireless Configuration Menu.
Point Test
The device discovery process automatically starts at the beginning of the Point Test.
To start a point test from the System Test Button:
1.

Ensure that all devices have exited RFSS Mode, including the wLSN Hub.
Ensure the wLSN Hub is in normal operating mode (LED is on steady).

Press the System Test button for one second.

To start a point test from the Phone Menu:
From the Installer Menu of a phone session (refer to Section 2.7.2 Initiate a Phone Session from
the Control Panel, Page 22):
–

Press [1], and then press [2] to select Full System Test.

OR
–

Press [1], and then press [3] to select System Test Menu. From the System Test Menu,
press [5] to select Point Test.

Wireless Configuration Menu
1.

Enter the Installer Menu of a phone session (refer to Section 2.7.2 Initiate a Phone Session
from the Control Panel, Page 22).

Press [1][6] to select System Maintenance Wireless Configuration. The device discovery
process automatically starts.

3.2.2

Establish and Configure the Wireless Network
The wLSN Hub automatically establishes and configures the wireless network.
The wLSN Hub evaluates each available radio frequency (RF) for noise, RF signal strength, and
other adjacent wireless systems. The wLSN Hub then selects the frequency with the lowest
amount of noise and least amount of traffic for network operation.
To configure the wireless network, the wLSN Hub selects the best channel for broadcasting.
Once a channel is selected, the wLSN Hub then configures all discovered devices to operate
on the selected frequency. This process takes several minutes.

Bosch Security Systems, Inc.

System Reference Guide

F01U087835 | 02 | 2008.10

en | Point Expansion

3.2.3

Easy Series

Configure Devices
Input and Output Devices
NOTICE!

The ISW-BMC1-S135X Door/Window Contact and the ISW-BIN1-S135X Inertia Detector have a
magnetic switch as an input. If the magnetic switch is not used, remove the magnet from the
device before starting the Point Test.
Once the network is established and configured, the system announces "Test all points." Test
the wireless devices in this order: input devices, output devices, and relay modules.
NOTICE!
Do not exit the Point Test until all intended wireless devices are tested. Otherwise, you must

manually add devices to the system.
If extra wireless devices not intended for installation are within the wireless hub's range, the
wLSN Hub might also discover these devices. To exclude any unused devices from the system,
press [#] (or [5] from the control center) to exit the Point Test. The wLSN Hub returns all
unused devices to the undiscovered state.
When you restore the device, the system announces the assigned device number.
Test Devices
Point numbers are assigned to wireless devices in the order that the devices first
communicate to the system (tampered, faulted, low battery). If specific point numbers are
preferred for wireless devices, ensure that the wireless devices communicate in the
appropriate order. Otherwise, the system assigns the lowest available point number to the
first tested wireless device. With motion detectors, unmask only the detector you want to
test. Refer to Table 2.6 on Page 24 for wLSN device testing instructions.
Key Fobs
1.

After the last wireless device is configured and the Point Test ends, press [#] repeatedly
until you exit the Installer Menu and end the phone session.

Start a new phone session, or press and hold [3] on the control center, and enter the
master user (User 1) passcode.

Press [4] [1].

Enter a passcode, and then re-enter the passcode.

Press [4] to add a key fob. Token assignment and voice description are optional.

Repeat Steps 4 to 7 to add more users and key fobs, or press [#] repeatedly to end the
phone session.

To create a key fob-only system (no wireless input or output devices installed), start at Step 2.
In a key fob-only system, adding the first key fob might take several minutes to complete as
the wireless network is established and configured. Subsequent key fob additions take less
time.

F01U087835 | 02 | 2008.10

System Reference Guide

Bosch Security Systems, Inc.

Easy Series

Point Expansion | en

3.3

Wireless Maintenance

3.3.1

Wireless Configuration Menu

Use the Wireless Configuration Menu to:
–
–

Add new wireless devices to an existing wireless system
Add wireless devices that were not discovered when the wireless network was first
discovered

–

Replace or delete wireless devices from an existing wireless system

To access the Wireless Configuration menu from the Installer Menu of a phone session (refer
to Section 2.7.2 Initiate a Phone Session from the Control Panel, Page 22), press [1] [6] for
Wireless Configuration.
Menu options are only available after the initial device discovery and point test is completed.
Button

Menu Option

Description

Replace a Device

Use this option to replace a known device with a new device.

Press
[1]

–

Press [1] to replace a point, or [3] to replace an output.
For a relay module, select either the input or output, and then enter the
appropriate number in Step 2.

–

Enter the desired point number or output number.
The device discovery process starts.

–

When the system announces "Test all points," activate the new device.
The new device replaces the current device. If other devices were
discovered in Step 2, they are returned to the undiscovered state.

[2]

Add a Device

Use this option to add more devices to the wireless network.
When you press [2] to select this option, the device discovery process starts.
When the system announces "Test all points," activate all of the new devices.
If other devices were discovered but not activated, they are returned to the
undiscovered state.

[3]

Delete a Device

Use this option to delete a known device from the system:
–

Press [1] to delete a point, or [3] to delete an output.

–

Enter the desired point number or output number.
If the selected point number corresponds with a relay module, both the
input and output are deleted from the system. If you only want to delete the
input or the output, you must disable the corresponding function through
programming.

–

Press [1] to delete the device.
The wireless hub deletes the device from the system, and the point type or
output function is set to 0 (Disabled).

[4]
[5]

Transfer Wireless Data

If you replace a hub, select this option to send wireless data from the control

(control panel-to-hub)

panel to the wireless hub.

Transfer Wireless Data

If you replace the control panel, select this option to send wireless data from

(hub-to-control panel)

the wireless hub to the control panel. This option deletes key fobs.

Bosch Security Systems, Inc.

System Reference Guide

F01U087835 | 02 | 2008.10

en | Point Expansion

Button

Easy Series

Menu Option

Description

Erase and Discover

If the wireless data in the control panel does not match the wireless data in the

Press
[6]

hub (Bus Device Trouble 50), use this option to erase the wireless data in both
the control panel and hub, and rediscover all devices.
This option is only available if the wireless data does not match in the control
panel and hub.
[#]

Exit Wireless

Select this option to return to the System Maintenance options.

Configuration
Table 3.2 Wireless Configuration Menu Options

3.3.2

Assigning Points 1 to 8 as Wireless Points
To assign an on-board point (1 to 8) as a wireless point, disable the point in programming
before starting the device discovery process. You can individually assign Points 1 to 8 as
wireless points.

3.3.3

Recovering the Wireless Network
Expert Programming Item Number 9999 restores the control panel to its factory default
settings. All wireless network data in the control panel is lost, but is retained in the wireless
hub.
To recover wireless network data from the wireless hub:
1.

From the Installer Menu of a phone session (refer to Section 2.7.2 Initiate a Phone Session
from the Control Panel, Page 22), press [1] to select System Maintenance.

Press [6][5] to transfer wireless data from the hub to the control panel.
This option deletes key fob assignments. You must reassign all key fobs.

3.3.4

Wireless System Messages
Refer to the following table for a description of system messages that pertain to the wireless
network.

System Message

Description

“Wireless devices not configured.”

Point Test was exited before all wireless points were tested.

“Extra device ignored.”

An attempt was made to add a device to a system that already contains the
maximum number of points or outputs.

“Point x was tested.”

A point was tested. RFSS is acceptable.

“Point x low.”

A point was tested. RFSS is unacceptable.

“Please wait.”

The wireless network is busy, or the control panel is waiting for the wireless
network to respond. The control center might show a single rotating segment
of the circle of protection with this message.

“Wireless error.”

The wireless hub is jammed, missing, or experiencing a trouble condition.

“Wireless devices x.”

“x” = the number of devices that are discovered, but not tested.

“Wireless devices not tested x.”

“x” = the number of devices that are discovered, but not yet configured.

“Point x not tested.”

The control panel assigned a point number to the device, but the device was
not tested (faulted, or tampered, and restored).
“x” = the voice description.
By default, the system announces the point number.
Table 3.3 Wireless System Messages

F01U087835 | 02 | 2008.10

System Reference Guide

Bosch Security Systems, Inc.

Easy Series

Programming Access Options | en

Programming Access Options
You can access the system to make programming changes using:
–

The Phone Menu

–

Remote Programming Software (RPS)

–

A Programming Key (using programming copied from a control panel previously
programmed using the Phone Menu or RPS)

4.1

System Access by Phone
NOTICE!

Once you configure a control panel using the Phone Menus, you can copy the programming
from the control panel to a programming key for use on another control panel, or for backup.
Refer to Section 4.3 Programming Keys, page 36.
The Installer Phone Menu and User Phone Menu provide access to system functions such as
testing the system, programming the system, and adding or changing users.
The Installer Phone Menu requires the installer passcode.
The User Phone Menu requires either the master user (User 1) passcode for full menu access,
or a user passcode for limited menu access.
If the passcode length = four digits:
–

The default installer passcode is 5432

–

The default master user passcode is 1234

If the passcode length = six digits:
–

The default installer passcode is 543211

–

The default master user passcode is 123455

To access the system menus, select one of the options shown in Table 4.1, Page 33.
Options
House Phone

Steps
–

Press [#][#][#].

–

Listen for the voice prompt to enter a passcode.

–

Enter the installer passcode to access the installer menu, or a user passcode to access
the user menu.

Outside Phones

–

Call the premises phone number.

–

After the call is answered by a person or by a telephone answering device, press
[*][*][*] to disconnect the answering party and access the system.

–

Listen for the voice prompt to enter a passcode.
If the phone is not answered by a person or telephone answering device, the system
answers after a programmed number of rings. Refer to Expert Programming Item
Number 222 listed in on Section Route Destination Items, page 47.

–

Enter the installer passcode to access the installer menu, or a user passcode to access
the user menu.

Installer Quick

Select this option if a phone line is not available, or a local connection is required. The

Connect

system must be off to use this option.
–

Connect a phone set to the test posts or to the phone terminals.

–

Press and hold the System Test button for approximately 15 sec.

–

Listen for the voice prompt to enter a passcode.

–

Enter the installer passcode to access the Installer Menu, or a user passcode to access
the User Menu.

Table 4.1

Bosch Security Systems, Inc.

Phone System Access Options

System Reference Guide

F01U087835 | 02 | 2008.10

en | Programming Access Options

Easy Series

NOTICE!

i
4.2

For an overview of the Installer Phone Menu and User Phone Menu, refer to Section 1.3 Phone
Menus, page 10.
For detailed Phone Menu programming options, refer to Section 5 Programming, page 37.

RPS
RPS (Remote Programming Software) is a Windows-based account management and control
panel programming utility designed to remotely set up and program specific control panels.
You can use RPS to program the control panel from a laptop or PC that is on-site or off-site
from the control panel.
For complete installation and operation instructions, refer to the RPS Installation and
Operation Guide (P/N: 4998141259) that is available on the RPS CD-ROM.
NOTICE!

i
4.2.1

Once you configure a control panel using RPS, you can copy the programming from the
control panel to a programming key for use on another control panel, or for backup. Refer to
Section 4.3 Programming Keys, page 36.

RPS Connection Methods
You connect to the Easy Series Control Panel to make changes interactively.
To connect RPS to the control panel:
1.

Open the control panel account by double-clicking the account, or select the account and
click Open.

2.
3.

Click Connect. The Panel Communication window opens.
Select a connection method from the Connect Via menu that best meets the system's
needs for remote programming. Refer to the following sections for descriptions of each
connection method.

Automatic
This option is the primary method to use for establishing a connection between RPS and the
control panel.
Connect the internal modem on the RPS PC, or an external modem, to the control panel.
Manual Dial
1.

Either the installer or RPS operator establishes a phone connection between the control
panel and RPS:
–

The installer dials the RPS phone number using the house phone, or connects a test
telephone to the control panel's test posts,

OR
–

From the RPS site, the RPS operator uses a telephone connected in parallel to the
RPS modem and manually dials the house phone number.

The RPS operator selects Manual Dial as the connection option on the RPS Panel
Communication window.

To answer the incoming call, the RPS operator clicks the Connect button on the RPS
Panel Communication window to establish a remote connection between RPS and the
control panel.

F01U087835 | 02 | 2008.10

System Reference Guide

Bosch Security Systems, Inc.

Easy Series

Programming Access Options | en

Modem Dial
The RPS operator uses a telephone connected in parallel to the RPS modem and clicks the
Connect To button in the RPS Panel Communication Window to dial the premises phone
number.
1.

Connect the internal modem on the RPS PC, or an external modem, to the control panel.

When the control panel answers the incoming call, the system announces "Enter your
passcode."

When you hear the control panel modem tones, press the Connect To button on the RPS
Panel Communication window. RPS then sends the DTMF tone to connect to the control
panel.

Direct Connect
Select this method to establish a local, on-site connection between the RPS PC (or laptop)
and the control panel.
1.

On the Telco side of the phone line, ensure that Tip and Ring are disconnected.

Connect the internal modem on the RPS PC, or an external modem, to the control panel.
Refer to Figure 4.1, Page 35.

Figure 4.1 Modem Connections

Connection using internal modem

Connection using external modem

270

Ω to 330 Ω, ¼ W resistor (for Direct Connection option only)
3.

If the first communication attempt fails, connect a 270 Ω to 330 Ω, ¼ W resistor in series
with the Tip House side. Refer to Figure 4.1, Page 35.

Network
Select this method to establish a network connection between the RPS PC (or laptop) and
the control panel using the ITS-DX4020-G or the DX4020.

Bosch Security Systems, Inc.

System Reference Guide

F01U087835 | 02 | 2008.10

4.3

en | Programming Access Options

Easy Series

Programming Keys
After you program a control panel using the Phone Menus or RPS, you can use a programming
key to transfer data from that control panel to another control panel. You can also use a
programming key to back up control panel data.
1.

If the system is on, turn it off.

Place the key's lock switch in the desired position. Refer to Figure 4.2.

Figure 4.2 Programming Key Lock Positions

Send data from control panel to key

Send data from key to control panel
3.

Insert the key into the control panel board.
–

Auto Transfer: If Expert Programming Item Number 123 = 1 (refer to Programming
Key Auto Transfer in Section 5.2.2 System Programming Items, page 43), the
programming key automatically transfers data depending on the position of the lock
switch.

–

Manual Transfer: If Expert Programming Item Number 123 = 0, you must use the
Installer Menu to access the programming key.
The control center announces when data transfer is completed.

When the (√) LED flashes green, data transfer is successful.
If the (√) LED flashes red, the data transfer is unsuccessful. Remove and reinstall the key.

F01U087835 | 02 | 2008.10

System Reference Guide

Bosch Security Systems, Inc.

Easy Series

Programming | en

Programming

Method

Description

Basic Programming

Basic Programming consists of a voice menu that contains the essential programming
items. Generally, finishing this programming section is usually all that is required for a
complete system.

Expert Programming

Expert Programming allows access to all programming categories for full system
configuration. Only use expert programming if you have a special programming
requirement.

Table 5.1 System Programming Methods

NOTICE!

You can program control panels using the remote programming software RPS. Like Expert
Programming, RPS allows access to all programming categories. For more information on RPS
and how to use a programming key to streamline a multiple-panel install, refer to
Section 4 Programming Access Options, page 33.
NOTICE!

For additional instructions and information for select programming items, refer to
Section 11 Programming Details and Defaults, page 102.
For country code specific defaults for programming items, refer to Section 11.3 Country Code
Specific Default Programming Codes, page 108.

Bosch Security Systems, Inc.

System Reference Guide

F01U087835 | 02 | 2008.10

en | Programming

Easy Series

5.1

Basic Programming

5.1.1

Enter Basic Programming
1.
2.

Select a system access option. Refer to Section 4.1 System Access by Phone, Page 33.
Enter the installer passcode to enter the Installer Phone Menu. Refer to
Section 2.7 Configure the System from the Installer Phone Menu, page 22.

Press [3] to enter Basic Programming. Refer to the figure below for the Basic
Programming Menu options.

1
System
Maintenance

2
User Menu
1

Points

Report Configuration

Outputs

Installer passcode
4-digit default: 5432
6-digit default: 543211

Basic
Programming

Country Code

Exit basic programming

Record point description

Set point type

Exit points

Select output function

Exit outputs

Enter account number

Configure report destinations

Remote Programming Success

Exit report configuration

4
Installer
Phone
Menu

Expert
Programming
5
Two-Way
Voice Session

6
Custom
Messages

7
Programming
Key
#

F01U087835 | 02 | 2008.10

Exit installer menu and end phone session.

System Reference Guide

Bosch Security Systems, Inc.

Easy Series

Programming | en

5.1.2

Points

Enter a point number from 1 to 32.

Record Point Description
For example, if Point 1 is located at the building's front door, say "Front Door" at the tone.
When recording your description, do not press any buttons on your phone until prompted.
Press [1] to continue programming the selected point.
Press [2] to re-record your current point description.

Set Point Type (Refer to Point Type

Point Types:

Point Types (cont.):

table)

–

Disabled

–

Silent Panic

Press [1] to select the current option.

–

Perimeter (Entry or Exit)

–

Interior Walkthrough

Press [2] to hear more options.

–

Interior (Follower)

–

Perimeter Exit Cancel

Press [#] to exit Point Type.

–

Perimeter Instant

–

Momentary Keyswitch

–

24-Hour

–

Maintained Keyswitch

–

Fire Verified

–

24-Hour Trouble

–

Fire Verified

–

User Emergency

–

Fire Instant

Exit Points
Return to the Installer Menu.

Bosch Security Systems, Inc.

System Reference Guide

F01U087835 | 02 | 2008.10

en | Programming

5.1.3

Easy Series

Report Configuration

[1]
Account Number

[2]
Report Destination
[1]
Route 1 Primary

[2]
Route 1 Backup

[3]
Route 2 Primary

[4]
Route 2 Backup

Format

Phone Number
or IP Address

[#]
Exit

ROUTE 1

[3]
Remote
Program Success

ROUTE 2

Phone Number: Enter phone number to dial and follow prompts.
IP Address: Enter “#” as first character, then follow prompts.

[#]
Exit

Account Number Entries

Phone Number/IP Address Entries

Entry

Key Press

Entry

Key Press

0 to 9

[0] to [9]

0 to 9

[0] to [9]

[*][1]

[*][*]

[*][2]

[*][#]

[*][3]

[*]1

[*][4]

Pause

[#]

[*][5]

Exit with Save

[#][#]2

Disable phone number

[0][#]

Disable IP address

240.0.0.0

[*] = . between each IP address notation.

Press [#] twice within two seconds to exit without saving

your entry.
Table 5.2 Account Number and Phone Number/IP Address Entries

F01U087835 | 02 | 2008.10

System Reference Guide

Bosch Security Systems, Inc.

Easy Series

Programming | en

5.1.4

Outputs
Output devices consist of horns, bells, strobes, or sirens.

Outputs

Enter an output number from 1 to 8

Set Output Function

Output Functions:

Output Functions (cont.):

–

Press [1] to select the current

–

Disabled

–

System On

option.

–

Intrusion

–

System Ready

–

Press [2] to hear more options.

–

Intrusion Latching

–

Key Fob On/Off

–

Press [#] to exit Output Function.

–

Fire

–

Key Fob 2-sec Pulse

–

Fire Latching

–

User Controlled

–

Intrusion and Fire

–

Interior Intrusion and Fire

–

Intrusion and Fire Latching –

System On (Unoccupied)

–

System Reset

Exit Points
Return to Installer Menu.
NOTICE!

When the installer PIN is entered at the keypad or phone, a 3 sec time window starts. During
that time window, a tamper alarm activates the interior siren for only 1 sec. Open the
enclosure door during this time to silence the sirens during maintenance. Once the enclosure
is closed, tamper alarm is restored after a 3 min delay. Tampers are logged and reported.
WARNING!

If you modify system parameters you are responsible for maintaining the system within the
scope of the standard and regulations that apply to the hardware and/or the system in which
it is used. In a NF A2P compliant installation, use only NF A2P listed components, and check
that each parameter is in the authorized range.

Bosch Security Systems, Inc.

System Reference Guide

F01U087835 | 02 | 2008.10

5.2

en | Programming

Easy Series

Expert Programming
Each category consists of several related programming items. Each programming item is
assigned a three- or four-digit number.
For No. 4 in the next figure, perform these steps:
1.
2.

Enter an expert programming item number. For example, 201, Phone Line Supervision.
Enter the desired value using your phone's keypad. For example, press [1] to enable
phone line supervision.

Repeat Steps 1 and 2 to configure other programming items, or press [#] to exit Expert
Programming.

1
System
Maintenance
2
User Menu
3
Basic
Programming

4
Expert
Programming

Installer passcode
4-digit default: 5432
6-digit default: 543211

Installer
Phone
Menu

5
Two-Way
Voice Session

6
Custom
Messages

7
Programming
Key
#

Exit installer menu and end phone session.

The following sections list programming items, item numbers, possible selections, and default
values. Record custom values in the Entry column next to the respective default value.

F01U087835 | 02 | 2008.10

System Reference Guide

Bosch Security Systems, Inc.

Easy Series

5.2.1

Programming | en

ROM Firmware Version Items

Programming Item

Item

Description

Number
Control Panel Firmware Version

090

System announces the control panel’s firmware
version.

Control Center 1 Firmware Version

091

System announces the control center’s firmware

Control Center 2 Firmware Version

092

version.

Control Center 3 Firmware Version

093

Control Center 4 Firmware Version

094

5.2.2

System Programming Items

Programming Item

Item

Selections

Number
Country Code (refer to

Manuf.
Default

102

00 to 65

103

0 = Disabled

Section 11.2 Country Codes)
Enclosure Tamper Enabled

1 = Enabled
Fire Bell Cut-Off Time

107

0 to 90 min

Intrusion Bell-Cut off Time

108

0 to 90 min

Intrusion Abort Window

110

15 to 45 sec

Fire Alarm Cancel Window

111

0 to 10 min

Intrusion Cancel Window

112

5 to 10 min

Chime Tone Select

114

1 = Chime door bell

2 = Single chime
3 = Standard door bell
Chime Mode Operation After System

115

Off

0 = Off

1 = On
2 = Follows previous setting

Automatic Test Report Frequency

116

0 = None

1 = Daily
2 = Weekly
3 = Monthly
Access Code

119

6 digits, using 0 to 9

999999

Daylight Saving Time Operation

121

0 = None

1 = North America (before 2007)
2 = Europe and Asia
3 = Tasmania, Australia
4 = Rest of Australia
5 = New Zealand
6 = Cuba
7 = South America and Antarctica
8 = Namibia, Africa
9 = USA after 2006
Installer Passcode Override Enabled

122

0 = Disabled

1 = Enabled

Bosch Security Systems, Inc.

System Reference Guide

F01U087835 | 02 | 2008.10

en | Programming

Programming Item

Easy Series

Item

Selections

Manuf.

Number
Programming Key Auto Transfer

123

Default
0 = Enable the programming key from the Installer

Menu.
1 = Programming key automatically sends or
receives stored programming data.
Point Alarm Verification

124

0 = None
1 = Cross zone
2 = Intelligent threat assessment
3 = Confirmed alarms 1
4 = Confirmed alarms 2

Faulted Points Allowed Threshold

125

0 to 8

Exit Delay

126

45 to 255 sec

Entry Delay

127

30 to 255 sec

Exit Time Restart

128

0 = User cannot reset Exit Delay timer

1 = User can reset Exit Delay timer one time
Recent Close Enabled

129

0 = Report not sent

1 = Report sent
Swinger Bypass Count

131

0-15

Auto Protection Level

132

0 = System turns on (unoccupied).

1 = System only turns on (unoccupied) if a
perimeter point is faulted during Exit Delay.
System On Order Options

133

1 = "Stay," "Leave," "Custom"

2 = "Stay," "Custom," "Leave"
3 = "Leave," "Stay," "Custom"
4 = "Leave," "Custom," "Stay"
5 = "Custom," "Leave," "Stay"
6 = "Custom," "Stay," "Leave";
Cross Zone Timer

134

60 to 3600 sec

120

Clear Alarm Memory

136

0 = By user, 1 = By master user

0 = Any user can clear condition

Latching Point and Enclosure Tamper 137

1 = Only the installer can clear condition
Latching System Device Tamper

138

0 = Any user can clear condition
1 = Only the installer can clear condition

Verbose System Test Enabled

139

0 = Test results announced only at end of all tests

1 = Test results announced after each test
Demo Mode

140

0 = Telephone messages heard only on phone

1 = Telephone messages heard on phone and
control centers
2 = Turn announcement of telephone messages over
the control center on or off at the control center
Restrict Installer Passcode

142

0 = Master user not needed

1 = Master user needed
Test Report Hour

143

0 to 23

Test Report Minute

144

0 to 59

Test Report Day of Week

145

0 to 6, where 0 = Sunday and 6 = Saturday

F01U087835 | 02 | 2008.10

System Reference Guide

Bosch Security Systems, Inc.

Easy Series

Programming Item

Programming | en

Item

Selections

Manuf.

Number

Default

Test Report Day of Month

146

1 to 28

Clear Confirmed Alarm Memory

147

0 = User can clear a confirmed alarm

1 = Only the installer can clear a confirmed alarm
Arming Beeps/Graduated

148

Annunciation

0 = No arming beeps or outputs during Entry Delay

1 = Outputs activate during Entry Delay, but no
arming beeps occur.
2 = Sound arming beeps, but outputs do not
activate during Entry Delay
3 = Sound arming beeps, and outputs activate
during Entry Delay

Wireless Jam Detect Level

150

Key Fob Arming

153

0 to 15

0 = Do not turn system on if there are faulted points 0
1 = Force arm faulted points if the number of
faulted points is within the range set in Expert
Programming Item Number 125
2 = Force arm faulted points even if the number of
faulted points exceeds the range set in Expert
Programming Item Number 125

Two-Way Voice Session Configuration 158

0 = Allow at any time

1 = Allow only during alarm conditions
Start Arming with Faulted Points

159

0 = Force arm all faulted points
1 = Exit Delay starts with faulted points

Speak Active Faults

160

0 = "Call for Service" announced
1 = Fault condition announced

Wireless Transmission Attenuation

161

Temporary attenuation for installation and

maintenance only. Not intended for normal
operation.
0 = None (normal operation)
1 = 3 dB
2 = 6 dB
3 = 9 dB
4 = 12 dB
Missing Wireless Device Conditions

162

0 = Creates a tamper condition (required for

EN50131-compliant countries).
1 = Creates a trouble condition.
Silence Trouble Tones

163

0 = All trouble tones announced

1 = Fire and 24-Hour trouble tones announced
System Inactivity Time (Hours)

164

0 to 255

System Inactivity Time (Days)

165

0 to 255

System Inactivity Time (Weeks)

166

0 to 255

Force Arm/Exit Error

167

0 = Off-normal points create an Exit Error at the end 0
of Exit Delay
1 = Off-normal points are force armed at the end of
Exit Delay

Bosch Security Systems, Inc.

System Reference Guide

F01U087835 | 02 | 2008.10

en | Programming

Programming Item

Easy Series

Item

Selections

Manuf.

Number
Audio Verification Command Set

168

Default
0 = Complies with SIA AV-01-1997.11
1 = Use alternate verification command set

Key Fob Duress

601

0 = Duress event disabled

1 = Duress event enabled
Key Fob Button Configuration

616

0 = Status request only
1 = Turn system on (occupied)

Key Fob Button Configuration

626

2 = Turn system on (custom protection)

3 = Turn output on or off
4 = Turn output on for 2 sec.
Default = Country-specific default. Select this programming item to hear the updated default value, or refer to Section 11.3 Country
Code Specific Default Programming Codes, page 108.

F01U087835 | 02 | 2008.10

System Reference Guide

Bosch Security Systems, Inc.

Easy Series

Programming | en

5.2.3

Communicator Programming Items
NOTICE!

To enable reporting, configure the following programming items:
–

Account Number (Expert Programming Item Number 100)

–

Route 1 Primary Destination (Expert Programming Item Number 206)

–

Format for Route 1 Primary Destination (Expert Programming Item Number 211)

Route Destination Items
Programming Item

Item

Selections

Manuf.

Number
Account Number

100

Default
000000

4 or 6 digits, using 0 to 9 and B to F.
Refer to Table 5.2, Page 40 for account number,
phone number, and IP address entry instructions.

Phone Line Supervision

201

0 = Unsupervised.

1 = Supervised.
PSTN or GSM Connection

202

0 = PSTN telephone line

Voice Format Repeat Count

203

1 to 15

Voice Format Message Delivery

204

1 to 5 in increments of 5 sec

0 = Do not wait for dial tone.

1 = ITS-DX4020-G Wireless Phone using GSM

Attempts
Dial Tone Detect

205

1 = Wait for dial tone.
Route 1 Primary Destination

206

Enter a phone number (up to 32 digits) or IP address 0

Route 1 Backup Destination

207

(000.000.000.000 to 255.255.255.255) for each

208

destination:

Route 2 Primary Destination
Route 2 Backup Destination

209

0 to 9 = [0] to [9]

* = [*][*]
# = [*][#]
Pause = [*][1]
Exit with save = [#]
Exit without save = [#][#]
Press [#] twice within two seconds to exit without
saving your entry.
Disable phone number = [0][#]
Disable IP address = 240.0.0.0

SMS Service Provider Number

210

Up to 32 digits.

Format for Route 1 Primary Destination 211

0 = Disabled

Format for Route 1 Backup Destination 212

1 = Contact ID

Format for Route 2 Primary Destination 213

2 = SIA

Format for Route 2 Backup Destination 214

3 = Voice

4 = SMS Text
5 = Fast Format
6 = Network (requires a 4-digit account number)

Call Waiting Disable

215

Enter a 3-digit string.

* = [*][*]; # = [*][#]
Emergency Call Override Number

216

Emergency Call Override Number Delay 217

Bosch Security Systems, Inc.

Enter a 3-digit emergency number, such as 911.

000

0 to 60 min

System Reference Guide

F01U087835 | 02 | 2008.10

en | Programming

Easy Series

Programming Item

Item

Selections

Manuf.

Number
Auto Detect Pulse Dial

218

Default
0 = Tone dialing only

1 = Auto Detect Pulse or Tone
Phone Answer Ring Count

222

1 to 255 rings

Enter 11 to bypass an answering machine.
Bell Test

223

0 = Disabled

1 = Enabled
Default = Country-specific default. Select this programming item to hear the updated default value, or refer to Section 11.3 Country
Code Specific Default Programming Codes, page 108.

Alternate Communication Items
Programming Item

Item

Selections

Number

Manuf.
Default

Port Number for Route Destination:

241

Route 1 Primary = 241

242

7700

Route 1 Backup =242

243

7700

244

7700

Route 2 Primary = 243
Route 2 Backup = 244

0 to 65535

7700

281

0 = Disabled

Route 1 Primary = 281

282

1 to 65535 min

Route 1 Backup =282

283

284

Heartbeat for Route Destination:

Route 2 Primary = 283
Route 2 Backup = 284
Acknowledge Wait Time for Route Destination

285

Route 1 Primary = 285

286

Route 1 Backup =286

287

288

Route 2 Primary = 2887
Route 2 Backup = 288

5 to 255 sec

289

0 = Disabled

Route 1 Primary = 289

290

1 = Enabled

Route 1 Backup =290

291

292

Anti-Replay for Route Destination:

Route 2 Primary = 291
Route 2 Backup = 292
Heartbeat Attempt for Route Destination:

293

Route 1 Primary = 293

294

Route 1 Backup =294

295

296

Route 2 Primary = 295
Route 2 Backup = 296
Extend Heartbeat Period

297

1 to 99

0 = Disabled
1 to 255 min

F01U087835 | 02 | 2008.10

System Reference Guide

Bosch Security Systems, Inc.

Easy Series

5.2.4

Programming | en

RPS Configuration Items

Programming Item

Item

Selections

Manuf.

Number

Default

RPS Passcode

118

6 digits, using 0 to 9 and A to F.

RPS Automatic Call In Frequency

224

0 = Never

123456

1 = Daily
2 = Weekly
3 = Monthly
RPS Automatic Call In Time (Hours) 225

0 to 23

RPS Automatic Call in Time

226

0 to 59

227

0 to 6, where 0 = Sunday and 6 = Saturday

228

1 to 28

(Minutes)
RPS Automatic Call in Time (Day of
Week)
RPS Automatic Call in Time (Day of
Month)
RPS Automatic Call in Phone

229

Number

Enter a phone number (up to 32 digits) or IP address
(000.000.000.000 to 255.255.255.255) for each
destination:
0 to 9 = [0] to [9]
* = [*][*]
# = [*][#]
Pause = [*][1]
Exit with save = [#]
Exit without save = [#][#]
Press [#] twice within two seconds to exit without saving
your entry.
Disable phone number = [0][#]
Disable IP address = 240.0.0.0

RPS Automatic Call in Method

245

0 = Phone number
1 = IP address

RPS Port Number

Bosch Security Systems, Inc.

246

0 to 65535

System Reference Guide

7750

F01U087835 | 02 | 2008.10

en | Programming

5.2.5

Easy Series

Route Reporting Options
Point Report and Restoral Routing

Programming Item

Item

Manuf.

Programming Item

Item

Number Default

Manuf.

Number Default

Point Reports and Restorals (all)*

301

Fire Trouble

328

Intrusion Alarm

307

Fire Trouble Restoral

329

Intrusion Alarm Verified

308

24-Hour Trouble

331

Intrusion Alarm Unverified

309

24-Hour Trouble Restoral

332

Intrusion Alarm 24-hr

310

Point Missing

333

Intrusion Alarm 24-hr Restoral

311

Point Missing Restoral

334

Intrusion Alarm Restoral

312

Supervisory Alarm

335

Duress

313

Supervisory Alarm Restoral

336

Fire Alarm

315

Wireless Point Low Battery

360

Fire Alarm Unverified

316

Wireless Point Low Battery Restoral

361

Fire Alarm Restoral

317

Fire Cancel

371

Panic

318

Point Tamper

388

Cancel

323

Point Tamper Restoral

397

Intrusion Trouble

324

Cross Zone Trouble

393

Intrusion Trouble Restoral

325

Alarm Recent Close

394

Intrusion Zone Bypass

326

Panic Restoral

399

Intrusion Zone Bypass Restoral

327

Cross Zone Trouble Restoral

400

Item

Manuf.

*Enter a value to globally set all of the following reports to the same value.
To modify one a specific report, enter a value in that report’s item number:
0 = Neither route
1 = Route 1 only; Primary and Backup
2 = Route 2 only; Primary and Backup
3 = Both routes; Primary and Backup

System On and Off Report Routing
Programming Item

Item

Manuf.

Programming Item

Number Default
System On and Off*

Number Default

302

Open

341

Exit Error

314

Open Keyswitch

342

Recent Closing

330

Open Remote

343

Close (System On) Unoccupied

337

Close (System On) Custom

344

Close (System On) Occupied

338

Opening by Guard Code

386

Close Keyswitch

339

Partial Close (System On)

403

Close Remote

340

(open and close) Reports (all)

*Enter a value to globally set all of the following reports to the same value.
To modify only a specific report, enter a value in that report's item number.
0 = Neither route
1 = Route 1 only; Primary and Backup
2 = Route 2 only; Primary and Backup
3 = Both routes; Primary and Backup

F01U087835 | 02 | 2008.10

System Reference Guide

Bosch Security Systems, Inc.

Easy Series

Programming | en

System Report and Restoral Routing
Programming Item

Item

Manuf.

Programming Item

Number Default

Item

Manuf.

Number Default

303

Communication Restoral

352

User Emergency2

319

Control Center Supervision Fail

353

User Fire3

320

Control Center Supervision Restoral 354

User Fire Restoral

321

Control Center Tamper

355

User Panic

322

Control Center Tamper Restoral

356

AC Fail

345

System Inactive

385

AC Fail Restoral

346

Watchdog Reset

390

Auto System Test Normal

347

Passcode Tamper

391

Auto System Test Off-Normal

348

Date/Time Changed

410

Auxiliary Power Fault

349

Network Fail

413

Auxiliary Power Restoral

350

Network Restoral

414

Communication Fail

351

Local Programming Success*

357

Bus Device Trouble

373

Low Battery

358

Bus Device Trouble Restoral

374

Low Battery Restoral

359

ROM Fault

375

Communication Test, Manual

362

Bell Trouble

376

Phone Line Fault

363

Bell Restoral

377

Phone Line Fault Restoral

364

Walk Test End

378

Remote Programming Failure

365

Walk Test Start

379

Remote Programming Success

366

Bus Device Missing

380

Wireless Receiver Jammed

367

Bus Device Missing Restoral

381

Wireless Receiver Jammed Restoral

368

Battery Missing

382

Bus Device Tamper

369

Battery Missing Restoral

383

Bus Device Tamper Restoral

370

RAM Checksum Failed

384

System Reports and Restorals

(all)1

Enter a value to globally set all of the following reports to the same entry.

To modify only a specific report, enter a value in that report's item number.

0 = Neither route
1 = Route 1 only; Primary and Backup
2 = Route 2 only; Primary and Backup
3 = Both routes; Primary and Backup
3To enable the control center's emergency buttons, set Expert Programming Items 889, 888, and 890.

Bosch Security Systems, Inc.

System Reference Guide

F01U087835 | 02 | 2008.10

en | Programming

Easy Series

Global Report Routing Items
Programming Item

Item

Selections

Manuf.

Number
Communicator Disable

304

Default
0 = Enable reporting

1 = Disable reporting (local-only system)
Route Attempts

305

Send Reports During Walk Test

306

1 to 20

0 = No reports

1 = Only Walk Test Start and Walk Test End reports
Default = Country-specific default. Select this programming item to hear the updated default value, or refer to Section 11.3 Country
Code Specific Default Programming Codes, page 108.

5.2.6

Point Programming Items

Programming Item Number Programming Item

Selections

(bold digits = Point Number)

9011, 9021, 9031, 9041...

Point Type

0 = Disabled

9101...9151...9201...9321

1 = Perimeter
2 = Interior
3 = Perimeter Instant
4 = 24-Hour
5 = Fire Verified*
6 = Fire Instant
7 = Silent Panic
8 = Interior Walkthrough
9 = Perimeter Exit Cancel
11 = Momentary Keyswitch
12 = Maintained Keyswitch
13 = 24-Hour Trouble
14 = User Emergency

9012, 9022, 9032, 9042...

Circuit Style

0 = Dual 2.2 kΩ alarm and tamper circuit

9102...9152...9202...9322
9013, 9023, 9033, 9043...

2 = Single 2.2 kΩ alarm circuit
Include in Custom Protection

9103...9153...9203...9323
9014, 9024, 9034, 9044...

0 = Point not included
1 = Point included

Cross Zone/Exit Route

9104...9154...9204...9324

0 = Cross zoning disabled, point is on the exit
route.
1 = Cross zoning enabled, point is on the exit
route
2 = Cross zoning disabled, point is not on the exit
route (must force arm).
3 = Cross zoning enabled, point is not on the exit
route.

9015, 9025, 9035, 9045...

Response Time

1 to 10 in 50 ms increments

9105...9155...9205...9325

F01U087835 | 02 | 2008.10

System Reference Guide

Bosch Security Systems, Inc.

Easy Series

Programming | en

Programming Item Number Programming Item

Selections

(bold digits = Point Number)

9016, 9026, 9036, 9046...

Alarm Verification

0 = Disable alarm verification

9101...9151...9201...9321
9018, 9028, 9038, 9048...

1 = Enable alarm verification
Wireless Detector Sensitivity

9108...9158...9208...9328

Motion Detector (PIR and dual)
0 = Standard
4 = Intermediate
Inertia Detector: Gross Attack Options
0 = Tap off, low sensitivity
1 = Tap off, low/medium sensitivity
2 = Tap off, medium/high sensitivity
3 = Tap off, high sensitivity
Inertia Detector: Minor Attack Options
8 = Tap on, 8 taps, low sensitivity
9 = Tap on, 8 taps, low/medium sensitivity
10 = Tap on, 8 taps, medium/high sensitivity
11 = Tap on, 8 taps, high sensitivity
12 = Tap on, 4 taps, low sensitivity
13 = Tap on, 4 taps, low/medium sensitivity
14 = Tap on, 4 taps, medium/high sensitivity
15 = Tap on, 4 taps, high sensitivity

Point Type (9011 ... 9321): Point 1 = 6, Points 2 - 5 = 1, Points 6 - 8 = 2, Points 9 - 32 = 0
Circuit Style (9012 ... 9322): Points 1 - 32 = 2
Custom Protection (9013 ... 9323): Points 1 - 32 = 0
Cross Zone Enabled (9021 ... 9321): 1
Response Time (9015 ... 9085): Points 1 - 8 only = 6
Wireless Sensitivity (9018 ... 9328): Points 1 - 32 = 0
Alarm Verification (9016 ... 9326): Points 1 - 32 = 0
Table 5.3

Bosch Security Systems, Inc.

Manuf. Default for Point Programming Items

System Reference Guide

F01U087835 | 02 | 2008.10

en | Programming

5.2.7

Easy Series

Output Programming Items

Programming Item

Item

Selections

Number
Fire Output Cadence

600

Manuf.
Default

0 = Temporal Code 3 cadence

1 = Pulse cadence
(two-sec on, two-sec off)
Output 1 Function (wired)

611

0 = Disabled

1 = Intrusion
2 = Intrusion Latching
3 = Fire
4 = Fire Latching
5 = Intrusion and Fire
6 = Intrusion and Fire Latching
7 = System Reset
8 = System On
9 = System Ready
10 = Key Fob On/Off
11 = Key Fob 2-sec Pulse
13 = User Controlled
14 = Interior Intrusion and Fire
15 = System On (Unoccupied)
16 = Intrusion and Fire 2
Output 2 Function (wired)

621

Output 3 Function (wired)

631

Output 4 Function (wired)

641

Output 5 Function (wireless)

651

Output 6 Function (wireless)

661

Output 7 Function (wireless)

671

Output 8 Function (wireless)

681

Output 4 Supervised Speaker Driver 642

0 = Supervised 8 Ω speaker driver

(wired)

1 = Unsupervised open collector

Default = Country-specific default. Select this programming item to hear the updated default value, or refer to Section 11.3 Country
Code Specific Default Programming Codes, page 108.

NOTICE!

When programming a wireless output (for example, a siren or relay module), do not select an
output function that requires the output to activate for an extended period (for example
System Ready).

F01U087835 | 02 | 2008.10

System Reference Guide

Bosch Security Systems, Inc.

Easy Series

5.2.8

Programming | en

Control Center Programming Items
Speech Configuration Items

Programming Item

Item

Selections

Manuf.

Number
Alarm Message Minimum Repeat Time

880

"No Alarm Report Sent" Announcement

883

Default
(1 to 255 hrs).

0 = Announcement disabled.

1 = Announcement enabled.
"Cancel Report Sent" Announcement

884

Time Format

887

1
0

0 = Determined by voice module
1 = Always use 12-hr mode
2 = Always use 24-hr mode

Global Control Center Items
These programming items affect all control centers connected to the control panel.
To send a user fire, emergency (medical) or panic report, the appropriate control center
button and report must be enabled. Refer to Section 5.2.5 Route Reporting Options on Page 50
to enable reports.
Check the appropriate box in the Easy Series User Guide (P/N: F01U0xxxxx) to identify which
buttons are enabled.
Programming Item

Item

Selections

Manuf.

Number
Fire Button Alarm

888

Default
0 = Disabled.

1 = Enabled.
Medical Button Alarm

889

0 = Disabled.

1 = Enabled
Panic Button Alarm

890

0 = Disabled.
1 = Enabled (audible).
2 = Enabled (silent).

One Button Arming

891

[i]

0 = Disabled (token or passcode required).

1 = Enabled (token or passcode is not required).

Invalid Passcode Attempt Limit

892

3 to 8.

Control Center Lockout Time

893

1 to 30 min.

Bosch Security Systems, Inc.

System Reference Guide

F01U087835 | 02 | 2008.10

en | Programming

Easy Series

Individual Control Center Items
Programming Item

Item Number

Selections

Manuf. Default

Control Center

Control Center 1: 811

1 (dim) to 5 (bright).

Control Center 1: 5

Brightness

Control Center 2: 821

Control Center 2: 5

Control Center 3: 831

Control Center 3: 5

Control Center 4: 841

Control Center 4: 5

Control Center
Backlight Extinguish
Mode

Control Center 1: 814

0 = Always on.

Control Center 1: 0

Control Center 2: 824

1 = Dim until user presence is

Control Center 2: 0

Control Center 3: 834

detected.

Control Center 3: 0

2 = Off until user presence is

Control Center 4: 844

detected.

Control Center 4: 0

3 = Off until user presents
token or enters passcode.
Default = Country-specific default. Select this programming item to hear the updated default value, or refer to Section 11.3 Country
Code Specific Default Programming Codes, page 108.

5.2.9

User Programming Items

Programming Item

Item

Selections

Manuf.

Number
Passcode Length

861

Default
Set the length of all passcodes

(4 or 6 digits).
Installer Passcode (User 0)
Master User Passcode (User 1)

7001

Four-digit Range: 1111 to 5555

5432

Six-digit Range: 111111 to 555555

543211

7011

1234
123455

Duress User (User 22) Enabled

862

0 = Duress user disabled
1 = Duress user enabled
2 = Guard code enabled
Duress User passcode:
Six digits: 111111
Four digits: 1111

RFID Token Password

863

Use this item to prevent unauthorized copying of tokens

123456

(00000000 to FFFFFFFF).

Default = Country-specific default. Select this programming item to hear the updated default value, or refer to Section 11.3 Country
Code Specific Default Programming Codes, page 108.

CAUTION!
Do not change the RFID Token Passwords item once tokens are added to the system.

F01U087835 | 02 | 2008.10

System Reference Guide

Bosch Security Systems, Inc.

Easy Series

Programming | en

5.2.10

Factory Default

Programming Item

Item

Selections

Number
Factory Default

9999

Enter 9999 to restore all factory default values. All programming items,
except for the country code, are reset when you restore the factory default
values. This item also deletes all wireless data, but does not default the
wireless hub.

!
5.3

WARNING!
For NF A2P installations, once the panel is configured, check that all parameters are within the
range of authorized values. Refer to Section 12.7 EN50131 Requirements, page 119.

Exit Programming
Press [#] repeatedly until the system says "goodbye." This ends the phone session.

Bosch Security Systems, Inc.

System Reference Guide

F01U087835 | 02 | 2008.10

en | Control Panel Event Codes (SIA and Contact ID)

Easy Series

Control Panel Event Codes (SIA and Contact ID)

Event
Intrusion Alarm
Intrusion Alarm Verified
Intrusion Alarm Unverified
Intrusion Alarm 24-hr
Intrusion Alarm 24-hr Restoral
Intrusion Alarm Restoral
Duress
Exit Error
Fire Alarm
Fire Alarm Unverified
Fire Alarm Restoral
Panic
Panic Restoral
User Emergency (Medical)
User Fire
User Fire Restoral
User Panic
Cancel
Intrusion Trouble
Intrusion Trouble Restoral
Intrusion Point Bypass
Intrusion Point Bypass Restoral
Fire Trouble
Fire Trouble Restoral
Recent Closing
Close (System On) Unoccupied
Close (System On) Occupied
Close (System On) Custom
Close (System On) Partial
Close (System On) Keyswitch
Open (System Off)
Open (System Off) Keyswitch

SIA
BA
BV
BG
BA
BH
BR
HA
EA
FA
FG
FH
HA
HH
QA
FA
FH
HA
BC
BT
BJ
BB
BU
FT
FJ
CR
CL
CL
CL
CL
CS
OP
OS

Report
Contact ID
Burglary Alarm
1 130
Burglary Alarm Verified
1 139
Unverified Event Burglary
1 130
Burglary Alarm
1 133
Burglary Alarm Restore
3 133
Burglary Restoral
3 130
Hold Up Alarm
1 121
Exit Alarm
1 374
Fire Alarm
1 110
Unverified Event-Fire
1 110
Fire Alarm Restore
3 110
Holdup Alarm
1 120
Holdup Alarm Restore
3 120
Emergency Alarm
1 101
Fire Alarm
1 110
Fire Alarm Restore
3 110
Holdup Alarm
1 120
Burglary Cancel
1 406
Burglary Trouble
1 380
Burglary Trouble Restore
3 380
Burglary Bypass
1 570
Burglary Unbypass
3 570
Fire Trouble
1 373
Fire Trouble Restore
3 373
Recent Closing
1 459
Closing Report
3 401
Closing Report
3 441
Closing Report
3 441
Closing Report
3 456
Closing Keyswitch (User 255) 3 409
Opening Report
1 401
Opening Keyswitch (User
1 409

Report
Burglary
Burglary
Burglary
24 Hour (Safe)
Restoral
Burglary
Duress
Exit Error (zone)
Fire
Fire
Fire
Panic
Panic
Personal Emergency
Fire
Fire
Panic
Cancel
Sensor Trouble
Sensor Trouble
Zone/Sensor bypass
Zone/Sensor bypass
Fire Trouble
Fire Trouble
Recent Closing
Unoccupied Arm by User
Occupied Arm by User
Custom Arm by User
Partial Arm by User
Keyswitch O/C (User 255)
O/C by User
Keyswitch O/C (User 255)

AC Fail
AC Fail Restoral
Auto System Test (Normal)
Auto System Test (Off-Normal)

AT
AR
RP
RY

255)
AC Trouble
AC Restoral
Automatic Test
Test Off Normal

1 301
3 301
1 602
1 608

AC Loss
AC Loss
Period Test Report (User 0)
Period Test Report, System

Auxiliary Power Fault
Auxiliary Power Restoral
Communication Fail
Communication Restoral
Control Center Supervision Fail
Control Center Supervision

IA
IR
YC
YK
EM
EN

Equipment Failure Condition
Equipment Fail Restoral
Communications Fail
Communications Restoral
Expansion Device Missing
Expansion Missing Restore

1 310
3 310
3 310
3 354
1 333
3 333

Trouble Present
Ground Fault
Ground Fault
Failure to communicate event
Failure to communicate event
Expansion module failure
Sensor Trouble

Restoral
Control Center Tamper
ES
Control Center Tamper Restoral EJ

Expansion Device Tamper
Expansion Device Tamper

1 341
3 341

Expansion Device Tamper
Expansion Device Tamper

Local Programming
Low Battery
Low Battery Restoral
Communication Test
Phone Line Fault

Restore
Local Programming Ended
System Battery Trouble
System Battery Restoral
Manual Test
Phone Line Trouble

1 628
1 302
3 302
1 601
1 351

Program mode exit
Low System Battery
Low System Battery
Manual trigger test report
Telco 1 fault

F01U087835 | 02 | 2008.10

LX
YT
YR
RX
LT

System Reference Guide

Bosch Security Systems, Inc.

Easy Series

Control Panel Event Codes (SIA and Contact ID) | en

Event
Phone Line Fault Restoral
ROM Fault
Bell Trouble
Bell Restoral
Walk Test Start
Walk Test End
Bus Device Missing
Bus Device Missing Restoral
Battery Missing
Battery Missing Restoral
RAM Checksum Failed
Point Tamper
Point Tamper Restoral
Cross Zone Trouble
Cross Zone Trouble Restoral
Point Missing
Point Missing Restoral
Wireless Point Low Battery
Wireless Point Low Battery

SIA
LR
YF
YA
YH
TS
TE
EM
EN
YM
YR
YF
TA
TH
BG
BR
UY
UJ
XT
XR

Report
Phone Line Restoral
Parameter Checksum Fail
Bell Fault
Bell Restored
Test Start
Test End
Expansion Device Missing
Expansion Missing Restore
System Battery Missing
System Battery Restoral
Parameter Checksum Fail
Tamper Alarm
Tamper Alarm Restoral
Unverified Event - Burglary
Burglary Restoral
Untyped Missing Trouble
Untyped Trouble Restore
Transmitter Battery Trouble
Transmitter Battery Restoral

Contact ID
3 351
1 304
1 320
3 320
1 607
3 607
1 333
3 333
1 311
3 311
1 303
1 137
3 137
1 378
3 378
1 381
3 381
1 384
3 384

Report
Telco 1 fault
ROM Checksum Bad
Sounder/ Relay
Sounder/ Relay
Walk Test Mode
Walk Test Mode
Exp. Module Failure
Exp. Module Failure
Battery Missing/Dead
Battery Missing/Dead
RAM Checksum bad
Tamper
Tamper Restoral
Cross-zone Trouble
Cross-zone Trouble
Loss of Supervision - RF
Loss of Supervision - RF
RF Low Battery
RF Low Battery

Restoral
Wireless Receiver Jammed
Wireless Receiver Jammed

XQ
XH

RF Interference
RF Interference Restoral

1 344
3 344

RF Receiver Jam Detect
RF Receiver Jam Detect

Restoral
Bus Device Tamper
Bus Device Tamper Restoral
Bus Device Trouble
Bus Device Trouble Restoral
Remote Programming Success
Remote Programming Failure
24-Hour Trouble
24-Hour Trouble Restoral
Opening by Guard Code
System Inactive
Network Fail
Network Restoral
Passcode Tamper
Firmware Updated
Watchdog Reset
Date/Time Change

XS
XJ
ET
ER
RS
RU
UA
UR
OR
CI
NT
NR
JA
YZ
YW
JT

RF Receiver Tamper
RF Receiver Tamper Restoral
Expansion Trouble
Expansion Restoral
Remote Program Success
Remote Program Fail
Untyped Zone Alarm
Untyped Zone Restoral
Disarm From Alarm
Fail to Close
Network Failure
Network Restoral
User Code Tamper
Service Completed
Watchdog Reset
Time Changed

1 341
3 341
1 330
3 330
1 628
1 628
1 150
3 150
1 450
1 454
1 350
3 350
1 461
1 412
1 305
1 625

Exp Module Tamper
Exp Module Tamper
System Peripheral Trouble
System Peripheral Trouble
Program mode exit
Program mode exit
24-Hour Non-Burglary
24-Hour Non-Burglary
Exception Open/Close
Failed to Close
Communication Trouble
Communication Trouble
Wrong Code Entry
Successful Download/Access
System Reset
Time/Date Reset

Bosch Security Systems, Inc.

System Reference Guide

F01U087835 | 02 | 2008.10

en | Default the System

Easy Series

Default the System

7.1

Default the Control Panel and the wLSN Hub
To restore the control panel to its factory settings, including programming data, and erase the
wireless network:
1.

Remove all power to the system.

Remove the wLSN Hub from its base. Refer to Figure 1.1, Page 6.

Record the current switch settings, then set the switches as follows: S1 = 9, S2 = 8, S3 =
7. Refer to Figure 1.1, Page 6.

Reconnect the wLSN Hub to the base.

Reapply all power to the system.

Wait for the green LED on the wLSN Hub to turn on and then off (approximately 5 sec).

Remove all power to the system.

Disconnect the wLSN Hub from the base again, and reset the switches to their previous
settings. Do not reconnect the wLSN Hub to the base yet.

Reapply all power to the system.

10. Default the control panel from the Installer Menu of a phone session
(Section 2.7.2 Initiate a Phone Session from the Control Panel, Page 22), press [4] to select
Expert Programming.
11. Press [9][9][9][9] to restore all factory default values.
12. Remove all power to the system.
13. Reconnect the wLSN Hub to the base.
14. Reapply all power to the system.
15. Default all wLSN devices.

7.2

Default wLSN Devices
Defaulting a wLSN device returns it to an undiscovered state.
To default a wLSN device:
1.

Remove the batteries.

Press and hold the tamper switch.

Reinsert the batteries while holding the tamper switch.
Continue to hold the tamper switch for at least 3 sec. The device's LED turns on.

Release the tamper switch within 5 sec. after the device's LED turns on.
The device's LED briefly turns off and then on, indicating that the device was returned to
an undiscovered state.
For specific instructions for defaulting each wLSN device, refer to the wLSN Reference
Guide (P/N F01U009440).

F01U087835 | 02 | 2008.10

System Reference Guide

Bosch Security Systems, Inc.

Easy Series

System Test and Maintenance | en

System Test and Maintenance

8.1

Test the System

Test the system for proper operation when installation and configuration are complete.
1.

Press the System Test button on the control panel board for one sec. The system
provides instructions throughout the test. Follow all instructions.

Contact the central monitoring station (CMS) to verify that all necessary test reports
were received, including test reports from all installed input and output devices.

8.2

Maintain the System
Bosch Security Systems, Inc. recommends testing the system regularly, and inspecting it
according to local code or law.

8.3

Installer History Event Announcements
The Installer Menu (refer to Section 2.7 Configure the System from the Installer Phone Menu,
page 22), speaks the event report status for each event.
After the event entry and its parameters (if any) are spoken, the system will beep and then
speak the status using two numbers. The first number indicates the route 1 event status. The
second number indicates the route 2 event status.
The numbers in each announcement indicate the status as follows:
–

0 = The event was logged only

–

1 = The event was successfully transmitted for this route

–

2 = The transmission of this event failed for this route

–

3 = The event is still pending for this route

Refer to the following table for a history event announcement example.
Entry

Event

Tone

Route 1 Status

Route 2 Status

Announcement

“AC Fail”

Beep

“One”

“Zero”

8.4

Event Messages
The following table shows:
–

Non-standard event messages that appear in the history log, and

–

Event messages for SMS Text and Voice formats

Event

History Log Entry

SMS Text Format

Voice Format

Tamper

Tamper 0

Point Trouble 0

Tamper 0

Intrusion Alarm System

Duress System Off User 22

Enclosure
Duress

Duress; System Off User 22

Off
Quick Arm

System On Occupied User System On System On User 0

System On Occupied User 0

Unoccupied User 0

System On Unoccupied User 0

System On Custom User 0

Keyswitch On System On Unoccupied 255

System On User 255

System On Unoccupied 255

Keyswitch Off System Off 255

System Off User 255

System Off 255

Recent Close

Intrusion Alarm

Recent Close User X

Bosch Security Systems, Inc.

System Reference Guide

F01U087835 | 02 | 2008.10

en | ITS-DX4020-G Communicator Configuration

Easy Series

ITS-DX4020-G Communicator Configuration

9.1

ITS-DX4020-G Communicator Overview
The ITS-DX4020-G provides wireless communications between the control panel and the
central monitoring station (CMS). You can configure the ITS-DX4020-G using one of two
methods:
–

Short Message Service (SMS)

–

Terminal Interface on a PC connected using a USB port

Figure 9.1 ITS-DX4020-G Communicator

1
2
3
4
5
6
7

Mini USB Port
Antenna Connector
CONFIG MODE (J200) Jumper Pins
LED DIS (J201) Jumper Pins
STATUS LED
CELL IP LED
AUDIO ACT LED

8
9
10
11
12
13

Signal Strength 1 (SS1) LED
Signal strength 2 (SS2) LED
Signal strength 2 (SS2) LED
Bus LED
SIM Cardholder
SIM Card In Cardholder (Door Open)

NOTICE!

To conserve power, install the LED disabling jumper to the LED DIS jumper pins when the
LEDs are not being observed.
When LED DIS jumper pins are shorted for the first time, the STATUS LED flashes the
firmware version.

F01U087835 | 02 | 2008.10

System Reference Guide

Bosch Security Systems, Inc.

Easy Series

ITS-DX4020-G Communicator Configuration | en

9.2

Short Message Service (SMS) Configuration
The ITS-DX4020-G supports configuration by SMS. The installer can send the SMS via mobile
phone to the ITS-DX4020-G. To ensure delivery of SMS data, keep each message to a
maximum of 160 characters in length with a maximum of 3 messages. The CONFIG MODE
jumper pins must be shorted together with a plug to allow the receipt of SMS data. Refer to
Table 2.9, Page 26, for LED activity. If the CONFIG MODE jumper pins are not shorted
together, incoming SMS data is discarded. If the shorting plug is removed from the CONFIG
MODE jumper pins before the ITS-DX4020-G receives the complete set of incoming SMS data,
all incoming SMS data is discarded.
When the ITS-DX4020-G receives a complete set of incoming SMS data, it saves the values
and then displays a distinct pattern across the on-board LEDs indicating that the values were
saved (refer to Table 2.9, Page 26 for LED locations). At this time, remove the plug from the
CONFIG jumper pins to restart the ITS-DX4020-G.The ITS-DX4020-G does not send out SMS
data. Table 9.1 shows the typical SMS format. Refer to Table 9.6, Page 69, and Table 9.7,
Page 69, for descriptions of each parameter ID in the SMS format.

Format

Character

Description

%SMS sequence number

If there are multiple SMS messages, the SMS sequence number

indicates the order of the messages and identifies the starting

point for the parameter IDs in each message.

Separate each id/value pair with a line feed (), carriage return

(), or semi-colon (;).
To allow spanning of configuration across multiple messages, each
SMS starts with the sequence number followed by the line feed
character.
id=

id/value pairs program each parameter on the ITS-DX4020-G.
id/value pairs are not split between multiple SMS parts.
If an SMS message contains id/value pairs with duplicate content,
only the value in the last duplicated pair is used.

The final part of a single (or multi-) SMS configuration has an
exclamation mark at the end.

Table 9.1

ITS-DX4020-G SMS Format

NOTICE!
To reduce message size, configuration items are designated with numbers, and only the
configuration items that must be changed are sent.

The configuration SMS string consists of a maximum of three SMS messages. When the ITSDX4020-G receives the final valid part of an SMS message, it accepts the configuration. The
communicator waits as long as the CONFIG jumper is on. When the CONFIG jumper is
removed, all incomplete configurations will be deleted.
Table 9.2 shows an example of a single SMS message.

Bosch Security Systems, Inc.

System Reference Guide

F01U087835 | 02 | 2008.10

en | ITS-DX4020-G Communicator Configuration

Easy Series

SMS Line No.

Description

SMS sequence number

1=4020G

Current password

2=secret123

New password (case sensitive)

3=123456,4343

PUK and new PIN to set in SIM

10=basic.m2m

APN

11=user@telco.com

GPRS username

12=password

GPRS password

15=1

Enable AES encryption

16=010203040506070809010111213141516

Sample AES key

14=134

Option bus address

End of configuration

Sample SMS
%1
1=4020G
2=secret123
3=123456,4343
10=basic.m2m
11=user@telco.com
12=password
15=1
16=010203040506070809010111213141516
14=134
!

Table 9.2 Single SMS Example

Table 9.3 and Table 9.4 show an example of a double SMS message split into two parts.
SMS Line No.

Description

SMS sequence number

1=4020G

Current password

2=secret123

New password (case sensitive)

3=123456,4343

PUK and new PIN to set in SIM

10=basic.m2m

APN

11=user@telco.com

GPRS username

12=password

GPRS password

15=1

Enable AES encryption

16=010203040506070809010111213141516

Sample AES key

Sample SMS
%1
1=4020G
2=secret123
3=123456,4343
10=basic.m2m
11=user@telco.com
12=password
15=1
16=010203040506070809010111213141516

Table 9.3 Double SMS Example, Part 1

SMS Line No.

Description

SMS sequence number

14=134

Option bus address

End of configuration

Sample SMS
%2
14=134
!

Table 9.4 Double SMS Example, Part 2

F01U087835 | 02 | 2008.10

System Reference Guide

Bosch Security Systems, Inc.

Easy Series

ITS-DX4020-G Communicator Configuration | en

9.3

Accessing the User Interface and Logging On Using USB

9.3.1

Downloading the ITS-DX4020-G USB Driver

Before you can access the USB user interface, you must download and install the ITS-DX4020G.inf file on the target PC or laptop. You only need to install this file once on the target PC or
laptop.
1.

From your Internet browser, go to http://www.boschsecurity.us/en-us/ to open the US
Bosch web site.

Under Online Catalogs, click Intrusion Alarm Systems.

Under Download Library, click Software.

Under Software, click Intrusion Alarm Systems.

Under Intrusion Alarm Systems, click Conettix - Information Transport Solutions.

To the right of ITS-DX4020-G.INF, click EN.
The File Download window opens.

Figure 9.2 File Download Window

9.3.2

Click Save to save the file to the target PC or laptop.

Installing the ITS-DX4020-G USB Driver
If the target PC or laptop only has one USB port, you only need to install the USB driver once.
If the target PC or laptop has multiple USB ports, you must install the USB driver each time
the ITS-DX4020-G is connected to a new USB port.
1.

Ensure that the supplied jumper plug is covering the CONFIG jumpers.
Refer to Figure 9.1, Page 62, Callout 3.

Supply power to the ITS-DX4020-G (12 VDC) and connect it to the target PC or laptop,
using a USB-to-mini-USB (5-pin mini-B connector) cable (not supplied).
The Found New Hardware Wizard opens.

Figure 9.3 Found New Hardware Wizard

Bosch Security Systems, Inc.

System Reference Guide

F01U087835 | 02 | 2008.10

en | ITS-DX4020-G Communicator Configuration

Easy Series

Select Install from a list or specific location (Advanced), and click Next.
The Search and Installation Options window opens.

Figure 9.4 Search and Installation Options Window

Under Search for the best driver in these locations, click the Include this location in the
search option, and then click Browse.
The Browse for Folder window opens.

Figure 9.5 Browse For Folder Window

In the file directory, go to the location where you saved the ITS-DX4020-G.inf file.
Click OK and then click Next.
The Found New Hardware Finish window opens.

Figure 9.6 Found New Hardware Finish Window

F01U087835 | 02 | 2008.10

Click Finish to complete the installation of the ITS-DX4020-G USB driver.

System Reference Guide

Bosch Security Systems, Inc.

Easy Series

9.3.3

ITS-DX4020-G Communicator Configuration | en

USB Main Menu
1.

From Windows, start a terminal session (launch Hyper Terminal if you are running
Windows XP or earlier, or download Tera Term if you are running Windows Vista). Set up
a connection on the new virtual serial COM port using the following settings:

–

Bit rate: 9600

–

Data bits: 8

–

Parity: None

–

Stop bits: 1

–

Flow control: None

Press [Enter].
The ITS-DX4020-G USB login screen opens.

Figure 9.7 ITS-DX4020-G USB Login Screen

Enter a valid password to log on. The default password is 4020G (all uppercase).
The user interface allows three attempts to correctly enter the password. After three
failed attempts, you must reset the ITS-DX4020-G by removing the jumper plug from the
CONFIG jumpers.

Press [Enter] to continue. The USB main menu opens.

Figure 9.8 ITS-DX4020-G USB Main Menu

The USB main menu appears:
–

after successfully entering a password

–

every time the user presses [Enter] without first selecting an option from the main
screen

–

Bosch Security Systems, Inc.

on returning from a sub-screen

System Reference Guide

F01U087835 | 02 | 2008.10

en | ITS-DX4020-G Communicator Configuration

Easy Series

The main menu shows all current configuration settings first. An asterisk in front of a
configuration item indicates that its setting has been changed during the current session.
The content of the main menu constantly scrolls. When a user performs a new action, any
resulting response from the user interface appears at the end of the menu.

9.3.4

USB Option Menu
Refer to Table 9.5 for a description of the USB option menu items.
To see the USB option menu, refer to Figure 9.8, Page 67.

Option

Press to Description
Select

1 Change password

To change the login password, enter the old password first, and then
enter the new password twice. The second entry is to confirm the new
password.
Passwords must be 4-15 characters long, and they are case-sensitive.
0-9, A-Z, a-z, and special characters are allowed.

2 Change log level

Change the debugging level shown on the View Log screen.

3 View log

View the debugging log. Press any key to exit.

4 Exit without Save

Return to the user interface login screen. All configuration changes that
were made are lost and are replaced with the default values.

5 Restore Factory defaults

Select Yes to restore all factory default configurations.
When prompted, remove the plug from the CONFIG jumper pins to
restart the ITS-DX4020-G.

6 Save and Reboot

Select Yes to save all configuration changes.
When prompted, remove the plug from the CONFIG jumper pins to
restart the ITS-DX4020-G.

7 Upgrade Software

Select this option to upgrade the software in the ITS-DX4020-G.
Refer to Section 9.4 Upgrading the ITS-DX4020-G Software, page 70.

8 Change Basic parameters

To change a basic parameter:
1. Select the parameter.
2. Enter the desired value and press [Enter].
Refer to Table 9.6, Page 69 for basic parameters.

9 Change Advanced parameters 9

Select to change advanced parameters.
Refer to Table 9.7, Page 69 for advanced parameters.

Table 9.5 ITS-DX4020-G Menu Options

At a configuration screen, items are presented one at a time with the current value inside [ ]
brackets. If you press [Enter] without entering a new value, the current value is unchanged.
To go to a specific menu option, enter the appropriate menu item number and press [Enter].

F01U087835 | 02 | 2008.10

System Reference Guide

Bosch Security Systems, Inc.

Easy Series

ITS-DX4020-G Communicator Configuration | en

Parameter

Default

Values

Description

Current Password

4020G

4 to 15 characters

Mandatory and case sensitive.

New Password

none

4 to 15 characters

New password, as desired. Case sensitive

SIM PUK,PIN

none

Maximum 10 numeric

Sets the PIN into the SIM and the ITS-

digits each

DX4020-G

SIM PIN

No PIN

4 numeric digits

Sets the PIN in the ITS-DX4020-G.

GPRS APN

1 to 63 characters

Access point name.

GPRS username

none

1 to 63 characters

Username for wireless service provider
(not always required).

GPRS password

none

1 to 63 characters

Password for wireless service provider (not
always required).

Src port

7700

Bus Address

134

1 to 65535 characters

Sets the port for the ITS-DX4020-G.

SDI: 80, 88

Sets the option bus address for

Option Bus: 134

communication with the control panel. For
Easy Series, use Address 134.

15
16

AES Encryption
AES Encryption Key

0 = Disabled

Security encryption on/off; must match

1 = Enabled

encryption settings in the receiver.

32 characters max.

Key must match encryption key in the

0-9, A-F, a-f allowed

receiver.

Description

Table 9.6 ITS-DX4020-G Basic Parameters

Parameter

Default

Values

DTMF digit timeout

500

100 to 3000 ms

Acceptable time between dialled DTMF
digits from the panel.

GPRS ACK timeout

6 to 120 secs

GPRS restarts if there is no response by
the entered time.

GPRS Transmit buffer

6 to 120 secs

lifetime

Duration the panel messages are buffered
in the communicator before being
discarded.

GSM CODEC setting

0 = Full Rate (FR)

Set to Full Rate when GSM is being used.

1 = Adaptive Multi-rate
(AMR)
54

GSM transmit gain

0 to 10

Gain on transmitted GSM signals

GSM receive gain

0 to 10

Gain on received GSM signals.

Enable incoming GSM

0 = Disabled

Enables/Disables incoming GSM calls.

calls where supported

1 = Enabled

Table 9.7 ITS-DX4020-G Advanced Parameters

Bosch Security Systems, Inc.

System Reference Guide

F01U087835 | 02 | 2008.10

en | ITS-DX4020-G Communicator Configuration

9.4

Easy Series

Upgrading the ITS-DX4020-G Software
To upgrade the software in the ITS-DX4020-G, you must download the latest ITS-DX4020-G
binary file from the Bosch website to the target PC or laptop, and then use either Hyper
Terminal or Tera Term to install the binary file on the ITS-DX4020-G.

9.4.1

Downloading the Latest Software
1.

From your Internet browser, go to http://www.boschsecurity.us/en-us/ to open the US
Bosch web site.

Under Online Catalogs, click Intrusion Alarm Systems.

Under Download Library, click Software.

Under Software, click Intrusion Alarm Systems.

Under Intrusion Alarm Systems, click Conettix - Information Transport Solutions.

To the right of ITS-DX4020-G_x.x.x.bin, click EN.
The File Download window opens.

9.4.2

Click Save to save the file to the target PC or laptop.

Installing the Software with Hyper Terminal
Microsoft® includes Hyper Terminal with the Windows XP® operating system, and earlier
operating systems.
1.

In Windows, click Start→All Programs →Accessories →Communications →Hyper
Terminal.

From the Hyper Terminal menu, click Transfer→Send File.
The Send File window opens.

Figure 9.9 Hyper Terminal Send File Window

Click Browse and go to the location where you downloaded the ITS-DX4020-G binary file.

In Protocol, select Xmodem.

Click Send to start the software upgrade.

When the software upgrade is complete, close Hyper Terminal, and remove the jumper
plug from the CONFIG jumpers on the ITS-DX4020-G. The ITS-DX4020-G restarts.

F01U087835 | 02 | 2008.10

System Reference Guide

Bosch Security Systems, Inc.

Easy Series

9.4.3

ITS-DX4020-G Communicator Configuration | en

Installing the Software with Tera Term
If you are using Microsoft® Vista®, you must download and install a communication utility,
such as Tera Term, on the target PC or laptop.
1.

Start Tera Term.

Select File→Transfer→XMODEM→Send.

Figure 9.10

Tera Term File Menu Path

In the XMODEM Send window, use the Look in: menu to find the location where you
downloaded the ITS-DX4020-G binary file.

Click Open to start the software upgrade.

Figure 9.11

Tera Term XMODEM Send Window

When the software upgrade is complete, close Tera Term, and remove the jumper plug
from the CONFIG jumpers on the ITS-DX4020-G. The ITS-DX4020-G restarts.

Bosch Security Systems, Inc.

System Reference Guide

F01U087835 | 02 | 2008.10

en | Device Specifications and Overview

Easy Series

Device Specifications and Overview

10.1

Control Panel

Enclosure
Dimensions (H x W x D):

37 cm x 31.8 cm x 8.5 cm (14.5 in x 12.5 in x 3.25 in)

Construction Material:

Cold-rolled steel, zinc seal, 0.36 mm thick (20 Ga.)

Environmental Considerations
Relative Humidity:

93% at 32°C 2°C (89.6°F 35.6°F)

Operating Temperature:

-10°C to +49°C (14°F to +120°F)
CE: -10°C to +40°C (+14°F to +104°F)
NF A2P: -10°C +55°C (+14°F to +131°F)

Storage Temperature:

-10°C to +55°C (+14°F to +131°F)

Protection Level

IP 30 - IK 04

Supervised Points
On-board Hardwire:

8
Single or dual end-of-line (2.2 k EOL) tamper point support
Point 1 supports two-wire smoke detectors
All points support four-wire smoke detectors
Enclosure tamper input (does not reduce point capacity)
Reaction time lower than 250ms

Programmable Outputs (PO)
On-board:

4
PO 1 only: Configurable relay
PO 2 to PO 4: Configurable solid state
PO 4 only: Internal supervised speaker driver option

PO 1 Relay Rating:

Contacts: 2 A with no jumper installed; resistive loads only; in a NF A2P
certified installation: 1 A
Output: 1.2 A with jumper installed; resistive loads only; in a NF A2P
certified installation 1 A
Operating Voltage: 30 VDC maximum

PO 2 to PO 4 Rating:

400 mA current sink

Number of...
Users:

22
User 1: Master user
Users 2 to 21: System users
User 22: Duress user

Events:

500 history events, stamped with time and date

Tokens and Key Fobs:

One per user (User 22 does not receive a token or key fob)

Phone Line
Phone line trouble voltage

Trouble condition occurs when the phone line voltage is between 1.10 V
and 4.75 V

Control Panel Power Requirements

F01U087835 | 02 | 2008.10

System Reference Guide

Bosch Security Systems, Inc.

Easy Series

AC Input Line Voltage

Device Specifications and Overview | en

Use a UL Listed 18 V Class 2 transformer (22 VAC, VA 50/60 Hz), or the
EZPS Power Supply
In an NF A2P certified installation, use the EZPS power supply delivered
with the panel

Total Alarm Power:

1.4 A (AC power and standby battery; intrusion applications only).
With a 7.0 Ah battery, the following current draws apply to all outputs and
devices connected to the system:
–

Up to 170 mA for 24 hr for fire and combined fire/burglary
applications

–
Auxiliary Power:

Up to 1.2 A for other applications

12 VDC, 1.0 A maximum. Includes 110 mA for each control center
connected to the system, and up to 400 mA for the programmable outputs.

Current Draw:

85 mA standby; 160 mA alarm with all outputs activated

Voltage:

12 VDC nominal (11.2 VDC to 12.3 VDC)
The control panel stops processing point faults when the voltage drops
below 9.5 VDC.

Battery:

D126 (7 Ah) or D1218 (18 Ah) sealed, lead acid rechargeable
1.7 A maximum recharging current
Low battery condition occurs when battery drops below 12 VDC
If AC power fails and the battery drops below 9.5 VDC, the control panel
stops processing point faults. Disconnect the battery under these
conditions.
Maximum auxiliary current to recharge standby battery within 72 hours:
–

12 V, 7 Ah Battery: 400 mA

–

12 V, 18 Ah Battery: 900 mA

In an NF A2P certified installation, use a battery Yuasa NP17-12IFR
EZPS Power Supply Requirements
AC Input:

AC Input Voltage: 100 VAC to 240 VAC
Line Voltage Frequency: 47 Hz to 63 Hz
Maximum Input Current: 0.5 A
Power Factor: Approximately 0.65 at full load

DC Output:

Nominal Output Voltage under AC line input: 18 VDC
Output Voltage Range under AC line input: 16 VDC to 20 VDC
Continuous Rated Output Current: 1.25 A
Output Current Limit: Approximately 1.75 A to 2.5 A
Periodic and Random Deviation (PARD): Less than 250 mV

Bosch Security Systems, Inc.

System Reference Guide

F01U087835 | 02 | 2008.10

en | Device Specifications and Overview

10.1.1

Easy Series

Standby Battery Calculation
Use the following formula to calculate standby battery capacity for 24 hr of standby power:
(Total B _____ x 24 hr) + (Total C _____ x 0.067 hr) + 10% reserve = Total battery Ah required
If the Column C total exceeds 1.4 A, use an external power supply.

Model

AC Power On Normal

AC Power Off Minimum

In Alarm Maximum Current

Current

Qty

Each Unit

Total

Each Unit

Total

Each Unit

Total

Used

(mA)

160

Control Panel

Control

110

x Qty

110

xQty

165

xQty

x Qty

xQty

x Qty

x Qty 0

xQty

xQty 0

330

xQty

160

Center
Wireless Hub
(IWT-WSN-N!86)
DX2010

Sounders Connected to PO 4
D118 8 Ω

xQty

Speaker
Ratings of other devices in system that are not shown above

F01U087835 | 02 | 2008.10

x Qty

Total

System Reference Guide

Bosch Security Systems, Inc.

Easy Series

10.2

Device Specifications and Overview | en

Control Center
Control Center Specifications

Control Center
Dimensions (H x W x D):

12 cm x 17.7 cm x 2.5 cm (4.7 in. x 7 in. x 1 in.)

Total Number Supported:

Recommended Mounting Surface: Non-metallic surface
Minimum Mounting Distance:

1.2 m (4 ft) between each control center

Current Draw:

110 mA standby; 165 mA alarm

Minimum Wire Length:

3 m (10 ft)

Maximum Wire Length:

Total: 400 m (1312 ft) using 0.8 mm (22 AWG) wire;
Single run: 100 m (328 ft) using 0.8 mm (22 AWG) wire

Data Bus Wire Type Options:

1 four-conductor, power-limited 1.2 mm (18 AWG) or 0.8 mm (22 AWG) wire
At least 0.6 mm (24 AWG) twisted pair CAT5 wire.
UL installations require power-limited wiring.

Audio Bus Wire Type Options:

1 two-conductor or 1 four-conductor, power-limited 1.2 mm (18 AWG) or 0.8
mm (22 AWG) wire. Only two conductors are used.
At least 0.6 mm (24 AWG) twisted pair CAT5 wire.
UL installations require power-limited wiring.
Unless using CAT5 cable, audio bus connections require a dedicated wire.

CAT5 Wire Requirements:

Refer to Section 2.2.3 Install the Control Center, page 14.

Protection Level

IP 30 - IK 04
Control Center Display States

Display

Color

Description

Green circle

No alarm or trouble conditions exist.
You can turn on the system.

Flashing green circle

System trouble exists. You can still turn on the system.
Alarm memory active.

Flashing amber circle

System trouble exists. You cannot turn on the system.
Alarm memory active.

Broken green circle

Wired point(s) are faulted. Turn on the system to bypass
faulted point(s).
Chime point faulted. Chime tone sounds.

Broken amber circle

Wired point(s) are faulted. You cannot turn on the system.

Broken red circle;

Fire or intrusion alarm occurred.

flashing red icons

Single rotating segment

Alarm memory announcement. Add or change user token.
Waiting for information from wireless network.

Bosch Security Systems, Inc.

System Reference Guide

F01U087835 | 02 | 2008.10

en | Device Specifications and Overview

Display

Easy Series

Color

Description

Green circle and icons

Add or change user passcode. Outside icon appears for first
passcode entry.
Inside icon appears for second passcode entry.

Green or amber

Point walk test.
Green single circle segments represent tested points.

Green flashing icons

Control center test. Icons alternately flash.

Table 10.1 System Off Display States

Display

Color

Description

Flashing red icon

Exit Delay in progress. Circle segments turn on, one at a
time, to provide a visual status of Exit Delay.

Red

System is on (occupied or custom protection).

Flashing icon

Entry Delay in progress.Circle segments turn off, one at a

(amber then red)

time, to provide a visual status of Entry Delay.
Amber icon: First half of Entry Delay.
Red icon: Second half of Entry Delay.

Broken red circle;

Fire or intrusion alarm occurred.

flashing red icons

Flashing red circle

Active alarm memory (if system is on).
System trouble exists.

Single red rotating segment

Alarm memory announcement (if system is on).

Broken red circle

At least one point is faulted or bypassed; no trouble exists.

Table 10.2 System On (Occupied or Custom Protection) Display States

F01U087835 | 02 | 2008.10

System Reference Guide

Bosch Security Systems, Inc.

Easy Series

Display

Device Specifications and Overview | en

Color

Description

Flashing red icon

Exit Delay in progress.

Red

System is on (unoccupied).

Flashing icon

Entry Delay in progress.

(amber then red)

Amber icon: First half of Entry Delay.

Red icon: Second half of Entry Delay.
Broken red circle;

Fire or intrusion alarm occurred.

flashing red icons

Flashing red circle

Active alarm memory (if system is on).

Single red rotating segment

Alarm memory announcement (if system is on).

Broken red circle

At least one point is faulted or bypassed; no trouble exists.

Table 10.3 System On (Unoccupied) Display States

Bosch Security Systems, Inc.

System Reference Guide

F01U087835 | 02 | 2008.10

en | Device Specifications and Overview

10.3

Easy Series

DX2010 Input Expander

NOTICE!
If Points 9 to 32 contain wired and wireless points, install all required DX2010 Input
Expanders before adding any wireless points to the system.

The DX2010 Input Expander connects directly to the data bus of a compatible control panel.
Each expander adds eight input loops.
DX2010 Input Expander
Operating Voltage:

8 VDC to 14 VDC

Current Draw:

35 mA standby; 135 mA maximum with connected accessories

Outputs:

100 mA, 12 VDC supervised output for accessories

Sensor Loop Terminal Wire Size: 0.8 mm (22 AWG) to 1.8 mm (14 AWG)
Wire Length:

Control panel to DX2010 (DX2010 auxiliary output not used):
–

0.8 mm (22 AWG) = 305 m (1000 ft)

–

1.2 mm (1.2 mm) = 610 m (2000 ft)

Control panel to DX2010 (DX2010 auxiliary output supplying 100 mA):
–

0.8 mm (22 AWG) = 30 m (100 ft)

–

1.2 mm (1.2 mm) = 76 m (250 ft)

Operating Temperature:

0°C to +50°C (+32°F to +122°F)

Relative Humidity:

5% to 85% at +30°C (+86°F)

Sensor Loop Resistance:

60 Ω maximum

Sensor Loop:

Up to eight inputs; input contacts can be normally open (NO) or normally closed
(NC) with appropriate EOL resistors for supervision.
Add a DX2010 Before Adding Wireless Points
The control panel supports up to three DX2010 modules. Each module occupies a group of
eight points.
The DX2010's DIP switch address determines which group of points the DX2010 occupies:
–

Address 102: DX2010 occupies Points 9 to 16

–

Address 103: DX2010 occupies Points 17 to 24

–

Address 104: DX2010 occupies Points 25 to 32

Refer to on Section 2.2.6 Install the DX2010 Input Expander, page 16, for more DIP switch
settings.
As each DX2010 module is added to the system, it occupies the next available group of points.
For Points 9 to 32, wireless points also occupy points in the same groups of eight as the
DX2010 modules:
–

If you add two DX2010 modules using Addresses 102 (Points 9 to 16) and 103 (Points 17
to 24), wireless points can only occupy Points 25 to 32.

–
–

If you add three DX2010 modules, wireless points can only occupy Points 1 to 8.
If you add a DX2010 module using address 102 (Points 9 to 16), wireless points can only
occupy Points 17 to 32.

F01U087835 | 02 | 2008.10

System Reference Guide

Bosch Security Systems, Inc.

Easy Series

Device Specifications and Overview | en

Add a DX2010 After Adding Wireless Points
If you add a DX2010 module after wireless points are added, based on its DIP switch address,
the DX2010 replaces the conflicting group of wireless points.
For example, if wireless points occupy Points 9 to 24, and you need Points 17 to 24 as wired
points, a DX2010 module with Address 103 replaces the wired points occupying Points 17 to
24.
If the next point grouping is available, for this example, Points 25 to 32, the control panel
retains all point programming except for voice descriptions, and moves the conflicting
wireless points to the next point grouping. You must re-record voice descriptions for the
points that were moved.
If the next point grouping is not available, the control panel deletes the conflicting wireless
points from the system.

10.4

Conettix DX4020 Network Interface Module
The Conettix DX4020 Ethernet Network Interface Module creates two-way communications
over Ethernet networks for compatible control panels.

DX4020 Network Interface Module
Operating Voltage:

12 VDC nominal

Current Draw:

10Base-T: 110 mA maximum; 100Base-T: 135 mA maximum

Operating Temperature:

0°C to +50°C (+32°F to +122°F)

Relative Humidity:

5% to 85% at +30°C (+86°F)

10.5

ITS-DX4020-G Communicator
The Conettix ITS-DX4020-G Communicator is a multi-function, dual-path security
communicator that communicates with Bosch Security Systems, Inc. Conettix receivers. It is
compatible with DX4020 protocols, and it provides a cellular (GSM/GPRS) modem.

ITS-DX4020-G GPRS/GSM Communicator
Operating Voltage:

12 VDC nominal, 10 VDC to 15 VDC

Current Draw:

Standby: 70mA, Alarm: 400mA

Operating Temperature:

-10°C to +55°C (+14°F to +131°F)

Relative Humidity:

5% to 95%

Ripple/Noise:

200 mVpp maximum

Bosch Security Systems, Inc.

System Reference Guide

F01U087835 | 02 | 2008.10

en | Device Specifications and Overview

10.6

Easy Series

wLSN Installation Tool
Use the wLSN Installation Tool to determine the best locations for wLSN device installation.
The Installation Tool communicates signal strength and packet success ratios through an LCD
display.
Specifications

868 MHz

ISW-BIT1-HAX, ISW-BIT1-HBX, ISW-BIT1-HCX

915 MHz

ISW-BIT1-HCX

Power

Docked

12 VDC nominal, 6 VDC to 14 VDC

Batteries

3 AAA NiMH rechargeable batteries that require an
initial charge of at least 7 hours of charging.
Operating Life: Up to 50 hours of continuous use on a
single charge.

EN50131-1

Environmental Class II
LED Displays
The crescent-shaped LED indicates charging status when placed in a docking station.
Refer to Figure 10.1 on Page 80 and Table 10.4 on Page 80.

Figure 10.1 wLSN Installation Tool

Power Indicator

Charging Status LED

LED (Green)

Status

Batteries fully charged

Off

Installation Tool operation on battery only.

Flashing

Batteries charging

Flashing power indicator

Low battery

Table 10.4 wLSN Installation Tool LED Status

F01U087835 | 02 | 2008.10

System Reference Guide

Bosch Security Systems, Inc.

Easy Series

Device Specifications and Overview | en

10.7

wLSN Hub
Specifications

868 MHz

ISW-BHB1-WX

915 MHz

ISW-BHB1-WY

Wire Gauge

0.14 mm to 1.5 mm

Wire Length

100 m

Power/Voltage

12 VDC nominal, 7 to 14 VDC

Current Draw

60 mA maximum

Compliance

EN50131-1 Security Grade 2 Type C, Environmental Class II
The wLSN Hub monitors and coordinates two-way communications between the control panel
and the detectors.
Rotary switches (S1, S2, and S3) configure device operation and enable special diagnostic
modes.
An LED on the front provides device status.
General Operation
Refer to Table 10.5 on Page 81 and Table 10.6 on Page 81 for an overview on wLSN Hub LEDs
and switch settings.

Operation

LED Display

Self Test and Hardware Failure

LED flashes twice per sec. This indicates failure. The wLSN Hub does
not operate.

Standard Operation

LED on.

Configuring Network

LED flashes once every 2 sec.

RFSS Mode

LED flashes once every 4 sec.
Table 10.5 wLSN Hub LED Displays

Switches
Function

Normal Operation

RFSS Mode

Default Mode

Table 10.6 wLSN Hub Switch Settings

Bosch Security Systems, Inc.

System Reference Guide

F01U087835 | 02 | 2008.10

en | Device Specifications and Overview

10.8

Easy Series

wLSN PIR and Dual Motion Detectors
The PIR Motion Detector (ISW-BPR1-W13PX) uses an infrared sensor. The Dual Motion
Detector uses (ISW-BPR1-W13PGX) both PIR and microwave technology.
A cover-and-wall tamper switch transmits a tamper signal when the cover is removed from its
base, or when the unit is pulled away from the wall.
An LED provides status for Walk Test, RFSS, and Discovery Modes.
Specifications

868 MHz

PIR: ISW-BPR1-W13PX
Dual: ISW-BDL1-W11PGX, ISW-BDL1-W11PHX, ISW-BDL1-W11PKX

915 MHz

PIR: ISW-BPR1-W13PY
Dual: ISW-BDL1-W11PGY, ISW-BDL1-W11PHY, ISW-BDL1-W11PKY

PIR Motion Detector Power/

Four AA 1.5 V alkaline batteries

Voltage
Dual Motion Detector Power/

Six AA 1.5 V alkaline batteries

Voltage
EN50131-1

Security Grade 2, Environmental Class II
Sensitivity Settings
Sensitivity settings are set at the control panel. Refer to the control panel's documentation for
detailed information.
1.

Standard Sensitivity
Use this setting when pets are present in the area to be monitored. Standard sensitivity
provides excellent detection performance and is the least sensitive to false alarms.

Intermediate Sensitivity
Only use this setting in non-pet installations where environmental disturbances are
minimal. Intermediate sensitivity provides the highest level of detection performance.

NOTICE!
The Dual Motion Detector's microwave motion sensor is factory adjusted to sense motion to
at least 11 m.

Setting the Dual Motion Detector's Microwave Range Adjustment
a.

If the microwave coverage needs adjustment (red or yellow LED does not light),
increase or decrease the microwave range as needed (using the back of the device).

F01U087835 | 02 | 2008.10

Repeat the Walk Test.

Repeat Steps a and b until the required coverage is met.

System Reference Guide

Bosch Security Systems, Inc.

Easy Series

Device Specifications and Overview | en

10.9

wLSN Door-Window Contact
The wLSN Door-Window Contact is a magnetic reed switch and wireless transceiver used for
monitoring doors, windows, and other dry contact devices.
A cover-and-wall tamper switch transmits a tamper signal when the cover is removed from its
base, or when the unit is pulled away from the wall.
An LED provides status for RFSS and Discovery Modes.
Specifications

868 MHz

ISW-BMC1-S135X

915 MHz

ISW-BMC1-S135Y

Maximum Distance Between Sensor and <12,7 mm, the magnet can be placed on either side.
Magnet

The base is marked to indicate the magnet position.

Wire Gauge

0.14 mm (22 AWG) to 1.5 mm (16 AWG)

Power/Voltage

Two AA batteries, 1.5 V alkaline

Terminal Block

For connecting other dry contact devices such as another magnetic reed
switch. (2.2k EOL)

EN50131-1

Security Grade 2, Environmental Class II
Supported Wiring Configurations
The wLSN Door-Window Contact provides a supervised point for monitoring external devices.
Refer to Section 2.2.7 Connect Supervised Points on page 19 for supported wiring options
when using the supervised point.

10.10

wLSN Recessed Door-Window Contact
The wLSN Recessed Door-Window Contact is a wireless transceiver used for monitoring doors
A cover tamper switch transmits a tamper signal when the cover is removed from its base.and
windows.
An LED provides status for RFSS and Discovery Modes.

NOTICE!
Mounting the wLSN Recessed Door-Window Contact in a metal door or window frame could
degrade the RF signal strength.

Specifications
868 MHz

ISW-BMC1-R135X

915 MHz

ISW-BMC1-R135Y

Power/Voltage

One CR2 lithium battery, 3 VDC

Maximum Distance Between Reed

<12,7 mm

Switch and Magnet
Drill Tools

Requires the use of a 19 mm (3/4 in.) drill bit and 22 mm
(7/8 in.) spade bit

Circuit Board Removal

Needle nose pliers are recommended

EN50131-1

Security Grade 2, Environmental Class II

Bosch Security Systems, Inc.

System Reference Guide

F01U087835 | 02 | 2008.10

en | Device Specifications and Overview

Easy Series

Tamper Switch Location
Refer to Figure 10.2 on Page 84 for the location of the device's tamper switch and LED.

Figure 10.2 Recessed Door-Window Contact

10.11

Mounting slots for printed circuit board

Tamper switch

LED for RFSS Mode and Discovery Mode

wLSN Mini Door-Window Contact
Similar to the wLSN Door-Window Contact, the wLSN Mini Door-Window Contact is a wireless
transceiver device used for monitoring doors and windows.
A cover-and-wall tamper switch transmits a tamper signal when the cover is removed from its
base, or when the unit is pulled away from the wall.
An LED provides status for RFSS, and Discovery Modes.
Specifications

868 MHz

ISW-BMC1-M82X

915 MHz

ISW-BMC1-M82Y

Power/Voltage

One CR2 lithium battery, 3 VDC

Maximum Distance Between Reed

<12,7 mm (1/2 in.)

Switch and Magnet

The magnet can be placed on either side of the detector.

EN50131-1

Security Grade 2, Environmental Class II
Tamper Switch Location
Refer to Figure 10.3 on Page 84 for the location of the device's tamper switch.

Figure 10.3 Mini Door-Window Contact Tamper Switch

F01U087835 | 02 | 2008.10

System Reference Guide

Bosch Security Systems, Inc.

Easy Series

10.12

Device Specifications and Overview | en

wLSN Inertia Detector
The wLSN Inertia Detector is a vibration detector combined with a wireless transceiver used
for monitoring doors or windows.
A cover-and-wall tamper switch transmits a tamper signal when the cover is removed from its
base, or when the unit is pulled away from the wall.
An LED provides status for Test, RFSS, and Discovery Modes.
Specifications

868 MHz

ISW-BIN1-S135X

915 MHz

ISW-BIN1-S135Y

Maximum Distance Between Detector

<12,7 mm (1/2 in.)

and Magnet

The magnet can be placed on either side of the detector.

Power/Voltage

2 AA batteries, 1.5 V alkaline

Sensor Adjustment

Adjust the position of the sensor element, so the arrow always points up by
removing and replacing the element to accommodate the possible
placement positions (refer to Figure 10.4 on Page 85).
Route the wiring from the sensor element so it does not make contact with
the tamper spring (refer to Figure 10.4 on Page 85).

EN50131-1

Security Grade 2, Environmental Class II
Sensor Adjustment
Proper sensor element orientation is critical to the operation of the device. The arrow,
embossed on the body of this sensor, must always point up. Refer to Figure 10.4 on Page 85
for arrow and for proper wire routing when reinserting the sensor element.

Figure 10.4

Sensor Adjustment

Remove sensor element

Turn sensor element as desired

Ensure arrow on sensor element points up

Proper wire routing

Bosch Security Systems, Inc.

System Reference Guide

F01U087835 | 02 | 2008.10

en | Device Specifications and Overview

Easy Series

Sensitivity Settings
All sensitivity settings are programmed at the control panel (refer to Section 5.2.6 Point
Programming Items, page 52). The sensor element has two settings:
–

Gross Attack

–

Minor Attack

Gross Attack is always enabled. The Minor Attack setting is very sensitive and can be disabled.
NOTICE!

A single tap such as a branch in the wind lightly brushing a window can start the minor attack
timer and tap count. To avoid false alarms, do not use the Minor Attack setting where there is
potential for stray vibrations.
Test Mode
The unit is automatically in Test mode for the first 10 minutes after power up.
The green LED flashes:
–

Once to indicate initialization is complete and the unit is in Test mode

–

Twice to indicate a Minor Attack test

–

Three times to indicate a Gross Attack test

F01U087835 | 02 | 2008.10

System Reference Guide

Bosch Security Systems, Inc.

Easy Series

10.13

Device Specifications and Overview | en

wLSN Key Fob
The wLSN Key Fob is a two-way personal transmitter carried by the user. Use it to remotely
arm or disarm a security area.
Specifications
868 MHz

ISW-BKF1-H5X

915 MHz

ISW-BKF1-H5Y

Power/Voltage

Two CR2032 lithium batteries, 3 VDC

Gaskets

Interchangeable; for multiple users, different colors available

EN50131-1

Security Grade 2, Environmental Class II

Key Fob User Interface
Refer to Figure 10.5 on Page 87, Table 10.7 on Page 88, and Table 10.8 on Page 88 for key fob
LED and button functions.

Figure 10.5

wLSN Key Fob Button and LED Locations

High intensity LED

Status LED

Disarm button

Arm button

Programmable buttons

LED/Button
High intensity LED
Status LED
Disarm button

Function
Suitable for use as a flashlight. Press

Refer to Table 10.8 on Page 88 for status indications.
Press

to turn the system off.

Press and hold
Arm button

Press

for 1 sec to create a panic alarm.

to turn the system on (unoccupied).

Press and hold

Bosch Security Systems, Inc.

to operate.

to create a panic alarm.

System Reference Guide

F01U087835 | 02 | 2008.10

en | Device Specifications and Overview

LED/Button

Easy Series

Function

Programmable buttons

To operate the programmable buttons, press and hold

for at least one sec.

Program these buttons at the control panel to control lights, garage doors, and so on.
Refer to Expert Programming Items 616 and 626 on page 56.
High intensity LED

Press [FIG] to operate the high intensity LED.

button
Table 10.7 wLSN Key Fob LEDs and Buttons

Status

Description

Alternating red and green

A key fob button was pressed. The LED either stops flashing, or one of the other status

Red fast flash

The system is in alarm, or silent panic feature was used.

Red slow flash

Exit delay in progress (system occupied or unoccupied).

Red on steady

The system is on (occupied or unoccupied).

Green fast flash

An error occurs while turning the system on. The system does not turn on as expected.

Green slow flash

The system is not ready to turn on. A button programmed for system status also shows

indicators in this table occurs. This display lasts approximately for 15 sec.

this status.
Green on steady

The system is off and is ready to turn on. The button programmed for system status
also shows this status.

Green on steady and slow
amber flash
Red on steady and slow
amber flash
Red blip

Either

was pressed to turn an output on or off.

Either

was pressed to turn an output on for two seconds.

If the LED flashes red once every 5 sec when the key fob is not in use, replace the
batteries.
Table 10.8 wLSN Key Fob LED Status

F01U087835 | 02 | 2008.10

System Reference Guide

Bosch Security Systems, Inc.

Easy Series

Device Specifications and Overview | en

10.14

wLSN Relay Module
The wLSN Relay Module allows the control panel to control external devices through a Form C
relay. This module also provides a supervised point for monitoring external devices.
Auxiliary power input terminals are also provided to supplement battery power when relay use
is high.
A cover-and-wall tamper switch transmits a tamper signal when the cover is removed from its
base, or when the unit is pulled away from the wall.
An LED provides status for RFSS and Discovery Modes.
Specifications

868 MHz

ISW-BRL1-WX

915 MHz

ISW-BRL1-WY

Wire Gauge

0.14 mm to 1.5 mm

Power

Four AA batteries, 1.5 V alkaline

External Power Source

12 VDC nominal, 6 VDC to 14 VDC

(optional)
Terminal Blocks

DC+ and DC -

External power source, 12 VDC nominal,
6 VDC to 14 VDC

PT + and PT - (input)

Input, supervised sensor loop

NO, C, NC (output)

Relay output for control of external devices.

Relay Output

2A at 30 VDC (resistive load)

EN50131-1

Security Grade 2, Environmental Class II

NOTICE!
The external power option is intended to be used as a supplemental (secondary) source of
power only. Do not operate the Relay Module without the batteries.

Bosch Security Systems, Inc.

System Reference Guide

F01U087835 | 02 | 2008.10

en | Device Specifications and Overview

10.15

Easy Series

wLSN Indoor Siren
The wLSN Indoor Siren provides auxiliary power input terminals are also provided to
supplement battery power when siren use is high.
A cover-and-wall tamper switch transmits a tamper signal when the cover is removed from its
base, or when the unit is pulled away from the wall.
An LED provides status for RFSS and Discovery Modes.
Specifications
868 MHz

ISW-BSR1-WX

915 MHz

ISW-BSR1-WY

Wire Gauge

0.14 mm to 1.5 mm

Power

Four AA batteries, 1.5 V alkaline

External Power Source

12 VDC nominal, 6 VDC to 14 VDC

(optional)
DC+ and DC - Terminal

External power source, 12 VDC nominal, 6 VDC to 14 VDC

Blocks

Sounder

85 dB at 3 m

EN50131-1

Security Grade 2, Environmental Class II

NOTICE!
The external power option is intended to be used as a supplemental (secondary) source of
power only. Do not operate the Indoor Siren without the batteries.

F01U087835 | 02 | 2008.10

System Reference Guide

Bosch Security Systems, Inc.

Easy Series

10.16

Device Specifications and Overview | en

wLSN Outdoor Siren
Specifications
868 MHz

ISW-BSR1-WOX

Wire Gauge

0.14 mm to 1.5 mm

Power

Two 2 x 13Ah (3.6 VCC nominal)

Outdoor Modulation

1400 – 1600 Hz, excursion of 200 Hz

Sounder

90 to 105 dB at 1m

EN50131-1

EN Environmental class IV outdoor

Configuration
Use the Outdoor Siren DIP switches to configure the siren for compliance with the laws of the
installation country. Refer to Figure 10.6, Page 91.

Figure 10.6

Outdoor Siren Configuration Switches

Refer to the following table for configurations allowed by the DIP Switch Settings.
Configuration

Region

OFF/OFF

Default

ON/OFF

Spain

DIP Switches

Configuration
–

Siren is limited to 90 sec.

–

Flashes every 1.5 sec from 0 - 90 sec of the alarm.

–

Flashes every 3 sec from 90 sec - 30 min of the alarm.

–

Flash stopped after 30 min.

–

Siren is activated for 60 sec, then 30 sec of silence, and then

–

Flashes every 1.5 sec from 0 - 150 sec of the alarm.

–

Flashes every 3 sec from 150 sec - 30 min of the alarm.

–

Flash stopped after 30 min.

activated for 60 more sec.

ON/ON

Belgium

–

Siren is limited to 90 sec.

–

Flashes every 1.5 sec from 0 - 90 sec of the alarm.

–

Flashes every 3 sec from 90 sec - 30 min of the alarm.

–

Flashes every 20 sec from 30 min of the alarm until the siren
is turned off.

OFF/ON

Reserved

Reserved for future use.

Table 10.9 Outdoor Siren DIP Switch Settings

Bosch Security Systems, Inc.

System Reference Guide

F01U087835 | 02 | 2008.10

en | Device Specifications and Overview

10.17

Easy Series

wLSN Smoke and Heat Detectors
The ISW-BSM1-SX (868 MHz) is a wireless smoke detector.
The ISW-BSM1-SY (915 MHz) is a wireless smoke and heat detector that provides fixed
temperature and rate-of-rise sensors.
Under normal conditions, the red LED flashes once every 8 sec while the sensor monitors the
surrounding environment. When the sensor detects smoke, the LED changes from flashing to
steady on and the sounder produces a loud continuous tone.
A self-diagnostic feature monitors detector sensitivity and operational status.
A cover tamper switch transmits a tamper signal when the cover is removed from its base, or
when the unit is pulled away from the wall.
The optical chamber is removable for easy maintenance.
Specifications
868 MHz

ISW-BSM1-SX

915 MHz

ISW-BSM1-SY

Power/Voltage

Two lithium batteries; 3 VDC

Fixed Temperature Sensor (ISW-

+57°C ± 3°C (+135°F ± 5°F)

BSM1-SY)
Raye-of-Rise Sensor (ISW-BSM1-

+8.3°C/min>+41°C (+15°F>+105°F)

SY)
Photoelectric Beam Obscuration

0.14 ± 0.04 dB/m

Sensitivity
Drift Compensation Adjustment

1.64%/m (0.5%/ft) maximum

Average Alarm Current

70 mA

Sounder

85 dBA at 3 m

Self-diagnostics Feature

Monitors detector sensitivity and operational status.

EN14604

ISW-BSM1-SX

Battery Replacement
The LED normally flashes every 8 sec. Replace batteries when the LED stops flashing and the
sensor chirps every 45 sec.
The low battery trouble chirps can be silenced for 24 hours by pushing the Test/Silence
Button. Refer to Figure 10.7 on Page 92 for the location of the Test/Silence Button.

Figure 10.7 wLSN Smoke Detector

High intensity LED

Test/Silence Button

F01U087835 | 02 | 2008.10

System Reference Guide

Bosch Security Systems, Inc.

Easy Series

Device Specifications and Overview | en

Smoke Test
Test smoke detectors annually using a listed aerosol smoke tester to simulate an alarm.
Follow the instructions on the can.
The LED should remain on while the detector provides a continuous tone. The detector
automatically resets when smoke is no longer present. A detector that fails to activate with
the Smoke test might require cleaning or replacement.

NOTICE!
To avoid a fire department dispatch, contact the central monitoring station or put the system
into Test mode before activating the detector using this method.

Sensitivity Test

NOTICE!
Test mode is seen by the control panel as a test. It does not send an alarm.

The detector includes a Sensitivity Level Test mode for determining the detector's sensitivity:
1.

Press and hold the Test/Silence button for 4 sec. The LED flashes 1 to 9 times and the
sounder activates.

Count the number of LED flashes and use Table 10.10 on Page 93 to determine the status
of the detector's sensitivity and the action to take.

Flashes

Action Recommended

Return device for service or replacement.

2 to 3

Clean the detector and re-test. If error persists, replace the detector.

4 to 7

Normal.

8 to 9

Confirm that the smoke chamber is snapped down securely. Clean the sensor and re-test.
Table 10.10

wLSN Smoke Detector Sensitivity Conditions

Silence an Alarm
Press the Test/Silence Button (refer to Figure 10.7 on Page 92) to silence the sounder during
an alarm. If smoke is still present after a few minutes, the sounder and alarm resume.
LEDs
LED

Status

Flashing

Normal.

Detects smoke (heat), sending an alarm.

Off

Replace the batteries, clean the detector, or replace the optical chamber as required.
Table 10.11

Bosch Security Systems, Inc.

wLSN Smoke Detector LED Statuses

System Reference Guide

F01U087835 | 02 | 2008.10

en | Device Specifications and Overview

Easy Series

Cleaning the Detector and Replacing the Optical Chamber
Clean the detector cover with a dry or damp cloth as needed to keep it free from dust and
dirt. Clean the detector interior at least once a year, or as needed.
To clean the detector:
1.

Rotate the detector counter-clockwise to remove it from the mounting base.

Remove the batteries.

Slide a flat head screwdriver in the slot on the detector cap and gently push down to pry
the cap off. Squeeze the optical chamber where indicated and pull it up and away from
the detector. Refer to Figure 10.8 on Page 94.

Figure 10.8 Remove the Detector Cap and the Chamber

Remove detector cap

Smoke Chamber Base

Optical Chamber

Alignment Arrows

Use compressed air or a soft-bristled brush to remove dust and dirt from the smoke
chamber base.

Align the new optical chamber with the base and snap into place.

To attach the detector cap, line the cap up with the detector, press the cap onto the
detector, and turn the cap clockwise to snap it firmly into place.

Observing the proper polarity, install the batteries and the battery cover. If the batteries
are not installed, the detector does not properly fit onto the mounting base.

Mount the detector onto the mounting base.

Test the detector's sensitivity.
Refer to Section Sensitivity Test on Page 93.

F01U087835 | 02 | 2008.10

System Reference Guide

Bosch Security Systems, Inc.

Easy Series

10.18

Device Specifications and Overview | en

wLSN Glassbreak Detector
Specifications
The wLSN Glassbreak Detector is a wireless transmitter used for detecting breaking glass.
A cover-and-wall tamper switch transmits a tamper signal when the cover is removed from its
base, or when the unit is pulled away from the wall.
Specifications

868 MHz

ISW-BGB1-SAX

915 MHz

ISW-BGB1-SAY

Power/Voltage

2 AA batteries, 1.5 V alkaline

Acoustic Capabilities

Glass types and thicknesses

Type

Thickness

Plate

0,24 cm to 0,95 cm

Tempered

0,32 cm to 0,95 cm

Laminated*

0,32 cm to 1,43 cm

Wired

0,64 cm

* Protected only if both panes of glass are broken.
Minimum pane size for all

28 cm x 28 cm

types of glass
Range

Maximum 7.6 m; no minimum range

General Overview

Figure 10.9

wLSN Glassbreak Detector Front Layout

Service door tamper switch

AA batteries

Service door

Test Mode pads

Sensitivity DIP switches

Event LED

Alarm LED

LED enable switch (off position)

Housing screw

RFSS Mode LED (remove housing screw and cover piece)

Bosch Security Systems, Inc.

System Reference Guide

F01U087835 | 02 | 2008.10

en | Device Specifications and Overview

Easy Series

Installation Considerations

NOTICE!
Glassbreak detectors are intended only as a component of a perimeter protection system. You
should always use a motion detector in conjunction with a glassbreak detector.

For the best detector performance, select a mounting location that is:
–

within 7.6 m of the protected glass.

–

within clear view of the protected glass.

–

at least 2 m from the floor.

–

at least 1 m from forced-air ducts.

–

at least 1 m from sirens or bells greater than 5 cm in diameter.

–

on a window frame if any heavy window covering is present.

Avoid mounting the detector:
–

in a corner.

–

on the same wall as the protected glass.

–

on free-standing posts or pillars.

–

in rooms with noisy equipment such as air compressors, bells, and power tools.

Sensitivity Settings
1.

If the front housing is attached, carefully open the service door (Item 3, Figure 10.9 on
Page 95).

Enable the LEDs for test purposes by sliding the LED ENABLE switch (Item 8, Figure 10.9
on Page 95) in the direction the arrow points (above the switch). An orange flag
protrudes from the side of the detector.
Refer to Figure 10.10 on Page 96.

Figure 10.10

wLSN Glassbreak Sensitivity Switches

Test pads

Sensitivity switches

F01U087835 | 02 | 2008.10

System Reference Guide

Bosch Security Systems, Inc.

Easy Series

Device Specifications and Overview | en

Determine the sensitivity setting for your application.
Refer to Table 10.12.

Sensitivity

SENS1

SENS2

Approximate Range

Maximum

OFF

7,6 m

Medium

OFF

4,6 m

Low

OFF

Lowest

1,5 m

Table 10.12

wLSN Glassbreak Detector Sensitivity Settings

Use a small screwdriver to move the sensitivity switches. Use the settings determined in
Step 3.

Turn on any sources of noise (such as machinery, office, or audio equipment) in the area.

Observe the green event LED (Item 6, Figure 10.9 on Page 95) for approximately 1 min. If
the green LED flashes, relocate the unit or reduce the sensitivity by adjusting the
sensitivity switch.

7.
8.

Repeat Steps 3 through 6 until you achieve the best sensitivity level.
After setting the sensitivity, slide the LED enable switch (Item 8, Figure 10.9 on Page 95)
to the OFF position.

Testing
Test the detector at least once each year. Test the detector with the 13-332 Sound Sensor
Tester.

Figure 10.11

13-332 Sound Sensor Tester

Activate/Test switch

Start button

Flex/Man switch

Bosch Security Systems, Inc.

System Reference Guide

F01U087835 | 02 | 2008.10

en | Device Specifications and Overview

Easy Series

Entering Test Mode
Place the detector in Test Mode. In Test Mode, the detector's LED disable switch (Item 8,
Figure 10.9 on Page 95) is overridden. You can enter the Test Mode locally or remotely.
To enter the Test Mode locally:
1.
2.

Carefully open the service door of the detector.
Insert a screwdriver into the slot next to the sensitivity switches that contains the test
pads (Item 1, Figure 10.9 on Page 95).

Momentarily short both test pads together with the tip of the screwdriver, or other
metallic conductive object.
The Event LED (green) (Item 6, Figure 10.9 on Page 95) flashes once per sec. If the green
LED does not flash, repeat Steps 10 and 11.

DANGER!
The 13-332 Sound Sensor Tester produces extremely loud sounds and can be hazardous to
hearing when used at close range. Do not point the 13-332 towards someone's head.
To enter the Test Mode remotely:
1.

Stand within 3 m of the detector.

Move the switches on top of the 13-332 Tester to ACTIVATE and to MAN modes (Items 1
and 3, Figure 10.9 on Page 95).

Point the front of the tester towards the detector and press the red Start button on top
(Item 2, Figure 10.9 on Page 95).

The tester buzzes and the green LED on the detector flashes once per sec. If the green LED
does not flash, move closer to the detector and repeat the procedure.
Testing
Testing the Detector (Flex and Audio Signals)
1.

Set the 13-332 Tester switches to the TEST and FLEX positions (Items 1 and 3,
Figure 10.9 on Page 95).

Press the red Start button (Item 2, Figure 10.9 on Page 95). The tester activates and
starts an eight-sec armed period.

If window coverings are present, close them fully.

Hold the 13-332 Tester near the point on the glass farthest from the detector. If window

Carefully strike the glass with a cushioned tool. The 13-332 Tester responds by producing

coverings are present, hold the tester between the glass and window coverings.
a burst of glass break audio.
If the detector receives both the flex and audio signals properly, its red Alarm LED lights for
3 sec.
If the red LED does not light, return to Section 9.0 RFSS Site Testing on page 81 to reposition
the detector.

F01U087835 | 02 | 2008.10

System Reference Guide

Bosch Security Systems, Inc.

Easy Series

Device Specifications and Overview | en

Exiting Test Mode
To exit the Test Mode locally:
1.

Carefully open the service door of the detector.

Insert a screwdriver into the slot next to the sensitivity switches that contains the test
pads (Item 1, Figure 10.9 on Page 95).

Momentarily short both test pads together with the tip of the screwdriver, or other
metallic conductive object.

When the detector exits Test Mode, the green Event LED (Item 6, Figure 10.9 on Page 95)
stops flashing. If the Event LED continues to flash, repeat Steps 2 and 3.
To exit the Test Mode remotely:
1.

Stand within 3 m of the detector.

Move the switches on top of the 13-332 Tester to ACTIVATE and to MAN modes (Items 1

Point the front of the tester towards the detector and press the red Start button on top

and 3, Figure 10.9 on Page 95).
(Item 2, Figure 10.9 on Page 95).
The tester buzzes.
Entering RFSS Mode with the Wall Tamper Removed
To enter RFSS Mode if the wall tamper tab is removed:
1.

Remove and reinsert the batteries.

Press and hold the wall tamper switch.
Refer to Figure 10.12 on Page 99.

Figure 10.12

Wall and Cover Tamper Switches

Wall tamper switch (back of detector)

Cover tamper switch (inside of detector)

Quickly press and release the cover tamper switch four times within 10 sec of reinserting
the batteries. Refer to Figure 10.12 on Page 99. The detector enters RFSS Mode.

Low Battery Indication
The detector indicates a low battery condition in two ways:
–

If the LEDs are enabled, both flash simultaneously every sec.

–

A low battery status indication is sent to the control panel.

The LED flashing and a low battery indication at the control panel are independent of each
other and do not necessarily occur at the same time. Receiving either condition indicates a
low battery.

Bosch Security Systems, Inc.

System Reference Guide

F01U087835 | 02 | 2008.10

100 en | Device Specifications and Overview

10.19

Easy Series

wLSN Water Sensor/Low-temperature Sensor
The wLSN Water Sensor/Low-temperature Sensor detects water spilled or leaking onto a
solid surface. It can also be used to monitor temperature to warn of potential water pipe
freezing. If temperatures fall below +7°C (+45°F) for more than 30 sec. the sensor sends a
signal to the wLSN Hub.
Specifications
868 MHz

ISW-BWL1-SX

915 MHz

ISW-BWL1-SY

Power/Voltage

Two AA batteries, 2.3 VDC to 3.0 VDC

Relative Humidity

Up to 95%, non-condensing

Temperature (operating)

-10°C to +55°C (+14°F to +131°F)

Temperature (alarm)

<+7°C (+45°F)

EN50131-1

Environmental Class II

Installation Considerations
The wLSN Water Sensor/Low-temperature Sensor is not intended to:
–

monitor water levels in storage tanks or other liquids

–

be permanently submerged in water

–

detect absence of water

Test and Enable wLSN Water Sensors/Low-temperature Sensors
Test each newly discovered device during the Point Test to enable the device. If specific point
numbers are preferred, test devices in the appropriate order.
Testing and Enabling When Both Sensors are Required
1.

During the Point Test, test the low-temperature sensor first. Refer to Table 10.13,
Page 100 for instructions.
The system announces "Point xx was tested."

Test the water sensor. Refer to Table 2 for instructions.

Testing and Enabling When Only the Water Sensor is Required
During the Point Test, test the water sensor. Refer to Table 10.13, Page 100 for instructions.
The system announces "Point xx was tested."
Testing and Enabling When Only the Low-temperature Sensor is Required
During the Point Test, test the low-temperature sensor. Refer to Table 10.13, Page 100 for
instructions.
The system announces "Point xx was tested."
Do not connect the water sensor probe.
Sensor

To Test

Water

Select one of the following methods:

Low-temperature

–

Short the water probe pins for at least 5 sec. Refer to Figure 10.13, Page 101.

–

Submerge the water probe in water for at least 5 sec.

Short the "T" pads for at least 5 sec. Refer to Figure 10.13, Page 101.
Table 10.13

F01U087835 | 02 | 2008.10

Water Sensor/Low-temperature Sensor Test and Enable Procedures

System Reference Guide

Bosch Security Systems, Inc.

Easy Series

Device Specifications and Overview | en 101

Figure 10.13

Enabling the Water Probe and Low-Temperature Functions

Water sensor

Low-temperature sensor

Bosch Security Systems, Inc.

System Reference Guide

F01U087835 | 02 | 2008.10

102 en | Programming Details and Defaults

Easy Series

Programming Details and Defaults
This section defines the primary function of the major programming items.
This section also lists the programming defaults for the most frequently used country codes.

11.1

Programming Item Programming Details
102. Country Code
Select the appropriate code for country-specific operation.
107. Fire Bell Cut-off Time
Enter how long the fire alarm sounds at bell outputs and at the control center.
108. Intrusion Bell Cut-off Time
Enter how long the intrusion alarm sounds at bell outputs and at the control center.
110. Intrusion Abort Window
Enter how long the control panel waits to send an alarm report after an alarm occurs.
111. Fire Alarm Cancel Window
Enter how long a user has to cancel a fire alarm report after the system sends the report to
the central station. If a fire alarm is acknowledged during the cancel window, the system
sends a cancel report to the central station. An entry of 0 disables this feature.
112. Intrusion Cancel Window
Enter how long a user has to cancel an intrusion alarm report after the system sends the
report to the central station.
115. Chime Mode Operation after System Off
Determines Chime Mode operation after the system is turned off.
116. Automatic Test Report Frequency
Determines how often the control panel sends the automatic test report.
118. RPS Passcode
Enter the 6-digit passcode that allows access to the control panel from RPS.
124. Point Alarm Verification
Determines the level of alarm verification required by point before generating an intrusion
alarm condition.
125. Faulted Points Allowed Threshold
Determines the maximum number of faulted points that are disabled while the system is on.
126. Exit Delay
Enter how long the user has to exit the building before the system turns on.
127. Entry Delay
Enter how long the user has to enter the building and turn off the system before an alarm
condition occurs.
131. Swinger Bypass Count
Enter the number of alarm reports allowed from a point while the system is on before the
point is bypassed.
133. System On Order Options
Determines the order that system-on options are announced to the user.
134. Cross Zone Timer
Enter how long the system waits for at least two Cross Zone points to be faulted before the
control panel sends a Verified Alarm report to the central station.

F01U087835 | 02 | 2008.10

System Reference Guide

Bosch Security Systems, Inc.

Easy Series

Programming Details and Defaults | en 103

140. Demo Mode
Demo Mode controls how telephone messages are announced by the system: either only over
the telephone, or over the telephone and through all idle control centers (control centers that
are not currently engaged in a command). Set Demo Mode to 2 (Demo Mode Auto On/Off).
Enter the telephone menu.
On an idle control center, press the [i] button to either turn on or off the announcement of
telephone messages through all idle control centers. When you exit the telephone menu and
end the phone session, the system turns Demo Mode off.
142. Restrict Installer Passcode
If set to 0, the Master User must enable the Installer passcode before a person logged in with
the Installer passcode can perform any tasks through the phone menu or RPS; enabling the
Installer passcode grants it Level 3 access. The Installer passcode remains at Level 3 until an
exit delay.
If set to 0, and the Installer is granted access while the control panel is armed, the
programming items are limited.
To enable the Installer Passcode:
1.

From the control center, the Master User enables enters the passcode. When the
validation for the Master User passcode expires, the Installer passcode is enabled.

Using a token, the Master User presents the token several times until the control center
speaks "Turning your system off". If the Master User token is presented again, the
Installer passcode is disabled.

From the phone interface, the Master User enters the passcode, then presses [3] for
System Maintenance, [3] for System Test menu, and then [6] to enable the Installer's
passcode.

145. Test Report Day of Week
Select the day that the control panel sends the test report.
146. Test Report Day of Month
Enter the day of the month that the control panel sends the test report.
148. Arming Beeps/Graduated Annunciation
Select whether the Intrusion and Intrusion and Fire Output Function types beep when the key
fob is used to arm or disarm the control panel.
150. Wireless Jam Detect Level
Configure the jam detect level of the wireless devices.
163. Silence Trouble Tones
Silence annunciation of trouble tones.
164. System Inactivity Time (Hours)
Enter the number of hours that the system must be turned off before it sends the System
Inactive report.
165. System Inactivity Time (Days)
Enter the number of days that the system must be turned off before it sends the System
Inactive report.
166. System Inactivity Time (Weeks)
Enter the number of weeks that the system must be turned off before it sends the System
Inactive report.
168. Audio Verification Command Set
Select the command set that the control panel uses for internal alarm verification. Press the
[*] key on the phone to enable the microphone on the control centers. This allows the central
station operator to hear noise on the premises. This option only effects the button presses on
the phone while an audio verify session is active between the control panel and the central
station operator.
Bosch Security Systems, Inc.

System Reference Guide

F01U087835 | 02 | 2008.10

104 en | Programming Details and Defaults

Easy Series

224. RPS Automatic Call In Time (Hours)
202. PSTN or GSM Connection
Select the type of telephone connection the system will use to send reports to the central
station.
203. Voice Format Repeat Count
Enter the number of times the system repeats a voice report during the phone call.
204. Voice Format Message Delivery Attempts
Enter how many times the system attempts to deliver a voice format message.
217. Emergency Call Override Number Delay
Enter the amount of time the system waits before sending reports if an emergency number is
dialed.
222. Phone Answer Ring Count
Enter the number of rings before the system answers an incoming call.
223. Bell Test
This programming item applies to all Intrusion output functions and to all arming modes.
0 = No closing ring-back or bell test; 1 = Enabled
If closing reports are disabled, the outputs turn on for 1 sec at the end of Exit Delay.
If closing reports are enabled, the outputs turn on for 1 sec when the control panel receives a
closing report acknowledgement from the central station.
Select the hour when the control panel calls RPS.
225. RPS Automatic Call in Time (Minutes)
Select the minute when the control panel calls RPS.
227. RPS Automatic Call in Time (Day of Week)
Select the day of the week when the control panel calls RPS.
228. RPS Automatic Call in Time (Day of Month)
Select the day of the month when the control panel calls RPS.
229. RPS Automatic Call in Phone Number
Enter the phone number that the control panel uses to call RPS.
245. RPS Automatic Call in Method
Select whether the control panel uses a phone number or an IP address to call RPS.
246. RPS Port Number
Enter the port number for contacting RPS when the automatic call in occurs over a network
connection.
305. Route Attempts
Enter the number of times the system attempts each destination in the selected route if the
first attempt fails.
601. Key Fob Duress
Select whether or not a wireless key fob sends a Duress event when the Arm and Disarm
buttons are pressed and held together.

F01U087835 | 02 | 2008.10

System Reference Guide

Bosch Security Systems, Inc.

Easy Series

Programming Details and Defaults | en 105

611. Output 1 Type
–

Disabled: Output is disabled.

–

Intrusion: Output turns on when intrusion alarm occurs. To turn off output, turn off
system, or wait until end of intrusion bell cut-off time.

–

Fire: Output turns on when a fire alarm occurs. To turn off output, turn off system if it is
already on, or wait until end of fire bell cut-off time.

–

Fire Latching: Output turns on when a fire alarm occurs. To turn off output, turn off
system if it is already on, or acknowledge alarm if system is off.

–

Intrusion and Fire: Output turns on when an intrusion or fire alarm occurs. To turn off
output, turn off system, or wait until end of bell cut-off time. Fire alarms take priority over
intrusion alarms.

–

Intrusion and Fire Latching: Output turns on when an intrusion or fire alarm occurs. To
turn off output, turn off system if it is already on, or acknowledge alarm if system is off.
Fire alarms take priority over intrusion alarms.

–

System Reset: Output is normally on. Output turns off for approximately 10 sec when
system is reset. Use this function to supply power to devices such as four-wire smoke
detectors that require power interruption to reset a latching alarm condition

–

System On: Output turns on when the system is turned on, and remains on until system
is turned off.

–

System Ready: Output turns on when the system is ready to turn on (no faulted points or
system troubles exist).

–

Key Fob On/Off: Output turns on or off when the user presses the key fob's

key.
–

Key Fob 2-sec Pulse: Output turns on for two seconds when the user presses the key
fob's

–

key.

User Controlled: Output turns on or off when a user or the installer uses the Operate
Outputs option from the phone menus.

–

Interior Intrusion and Fire: Output turns on when an interior intrusion or fire alarm
occurs. To turn off output, turn off system, or wait until end of bell cut-off time. Fire
alarms take priority over intrusion alarms.

–

System On (Unoccupied): Output turns on when the system is turned On (Unoccupied)
and there are no bypassed or force-armed points.

–

Intrusion and Fire:
–

Output turns on when any alarm (Intrusion or Fire) occurs. To turn off the output,
turn off the system, or wait until the end of the bell cut-off time.

–

When a fire alarm occurs, this output function provides only a steady output (no
Temporal Code 3 or Pulsed cadence).

–

Fire alarms take priority over Intrusion alarms.

880. Alarm Message Minimum Repeat Time
Enter how long the control center waits between alarm message announcements before
repeating the message even if the control center's proximity sensor detects motion.

Bosch Security Systems, Inc.

System Reference Guide

F01U087835 | 02 | 2008.10

106 en | Programming Details and Defaults

Easy Series

9xx1. Point Types
–
–

Disabled: Point is disabled.
Perimeter (Entry or Exit): If faulted and the system is on, Entry Delay starts. An alarm
occurs if the system is not turned off when Entry Delay ends.

–

Interior (Follower): If the system is on occupied, it ignores these points. If the system is
on unoccupied, a faulted interior point starts an alarm. These points are ignored during
Exit and Entry Delay times.

–

Perimeter Instant: If faulted when the system is on, a local alarm occurs

–

24-Hour: If faulted, an alarm always occurs. To restore a 24-hour point, turn the system
off if it is on, or acknowledge the alarm if the system is off.

–

Fire Verified: If faulted, fire verification occurs. If a second fire event occurs during the
two-min. wait period, a fire alarm occurs. If no second fire event occurs, the system
returns to normal.

–

Fire Instant: If faulted, a fire alarm always occurs.

–

Silent Panic: If faulted, an alarm always occurs. There is no visual or audio indication of
the alarm.

–

Interior Walkthrough: If faulted and the system is on custom protection, Entry Delay
starts. If the system is on occupied or unoccupied, this point functions as an interior
point.

–

Perimeter Exit Cancel: If faulted and restored during Exit Delay, Exit Delay stops and the
system immediately turns on.

–

Momentary Keyswitch: Turn the system on or off using a momentary keyswitch.

–

Maintained Keyswitch: Turn the system on or off using a maintained keyswitch.

–

24-Hour Trouble: If faulted, a trouble condition always occurs. To restore a 24-hour
trouble point, turn they system off if it is on, or acknowledge the alarm if the system is
off.

–

User Emergency, 24-hour supervisory point type:
–

If the point's circuit style = 0, an open or shorted circuit creates a tamper condition.
An off-normal circuit creates an alarm condition.

–

If the point's circuit style = 1, an open or shorted circuit creates an alarm condition.

–

Refer to Circuit Style on page 68 for more information.

–

If User Emergency is assigned to a wireless detector, any off-normal alarm condition
creates an alarm condition.

–

To restore a user emergency point, turn the system off if it is on, or acknowledge the
alarm if the system is off.

9xx6. Alarm Verification
Select whether or not the central station can verify the alarm when it receives an alarm report
from the point and the report is acknowledged.

F01U087835 | 02 | 2008.10

System Reference Guide

Bosch Security Systems, Inc.

Easy Series

11.2

Programming Details and Defaults | en 107

Country Codes
The country code sets the control panel to the appropriate country-specific defaults for your
installation.
Country

Code

Country

Code

Argentina

Israel

Australia

Italy

Austria

Japan

Belarus

Lithuania

Belgium

Luxembourg

Bosnia

Malaysia

Brazil

Mexico

Bulgaria

Netherlands

Canada

New Zealand

China

Norway

Croatia

Poland

Czech Republic

Portugal

Denmark

Romania

Egypt

Russian Federation

Finland

Spain

France

Sweden

Germany

Taiwan

Greece

Thailand

Hong Kong

Turkey

Hungary

Ukraine

India

United Arab Emirates

Indonesia

United Kingdom

Ireland

United States

Bosch Security Systems, Inc.

System Reference Guide

F01U087835 | 02 | 2008.10

108 en | Programming Details and Defaults

11.3

Easy Series

Country Code Specific Default Programming Codes
Country Codes

Prog Item# ↓

107
108
125
126
127
133
136
137
138
204
211
212
213
214
216
306
9011
9021
9031
9041
9051
9061
9071
9081
9012
9022
9032
9042
9052
9062
9072
9082
9092
9102
9112
9122
9132
9142
9152
9162
9172
9182
9192

5
5
0
60
30
1
0
0
0
3
0
0
0
0
110
0
6
1
1
1
1
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2

F01U087835 | 02 | 2008.10

3
3
3
60
30
1
1
0
0
3
0
0
0
0
112
0
1
3
3
3
3
3
3
3
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0

5
5
3
60
30
1
0
0
0
1
0
0
0
0
000
0
6
1
1
1
1
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2

5
5
3
60
30
1
0
0
0
1
0
0
0
0
112
0
6
1
1
1
1
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2

1
1
3
30
30
1
0
0
0
3
0
0
0
0
112
0
1
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2

3
3
0
45
45
3
0
1
0
3
0
0
0
0
112
0
6
1
3
3
3
2
2
2
2
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0

5
5
3
60
30
1
0
0
0
1
0
0
0
0
000
0
6
1
1
1
1
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2

5
5
3
30
25
3
0
0
0
2
0
0
0
0
112
0
6
1
2
2
3
3
4
3
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2

System Reference Guide

3
3
3
45
30
3
0
0
0
3
0
0
0
0
112
0
1
2
2
2
3
3
3
4
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0

5
5
0
60
30
1
0
0
0
3
0
0
0
0
110
0
6
1
1
1
1
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2

7
7
3
60
30
1
0
0
0
5
0
0
0
0
000
0
6
1
3
3
2
2
2
4
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2

5
5
3
60
30
3
0
0
0
3
0
0
0
0
112
0
6
1
1
1
1
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2

15
15
0
45
45
3
0
0
0
3
5
5
5
4
999
0
1
8
3
3
3
3
2
2
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0

3
3
3
30
20
1
0
0
0
5
3
3
3
3
113
0
1
3
3
3
2
2
2
4
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0

Bosch Security Systems, Inc.

Easy Series

Programming Details and Defaults | en 109

Country Codes
Prog Item# ↓

9202
9212
9222
9232
9242
9252
9262
9272
9282
9292
9302
9312
9322
814
824
834
844
861
611
621
631
641
642
121
600
115
116
128
132
147
153
159
160
344
403
9015
9025
9035
9045
9055
9065
9075
9085
163
168

2
2
2
2
2
2
2
2
2
2
2
2
2
0
0
0
0
4
5
5
5
5
0
2
0
0
0
1
0
0
1
0
1
3
3
6
6
6
6
6
6
6
6
1
0

Bosch Security Systems, Inc.

0
0
0
0
0
0
0
0
0
0
0
0
0
1
1
1
1
6
5
5
6
7
1
2
1
2
0
1
0
0
1
1
1
3
3
6
6
6
6
6
6
6
6
0
0

2
2
2
2
2
2
2
2
2
2
2
2
2
0
0
0
0
4
5
5
7
5
0
2
1
2
0
0
1
0
1
1
1
3
3
6
6
6
6
6
6
6
6
1
0

2
2
2
2
2
2
2
2
2
2
2
2
2
0
0
0
0
4
5
5
7
5
0
2
1
0
0
1
1
0
1
1
1
3
3
6
6
6
6
6
6
6
6
1
0

2
2
2
2
2
2
2
2
2
2
2
2
2
1
1
1
1
4
5
5
7
5
1
2
1
2
0
1
1
0
1
1
1
3
3
6
6
6
6
6
6
6
6
1
0

0
0
0
0
0
0
0
0
0
0
0
0
0
1
1
1
1
4
5
5
7
6
1
2
1
2
0
1
0
0
0
1
1
3
3
6
6
6
6
6
6
6
6
1
0

2
2
2
2
2
2
2
2
2
2
2
2
2
0
0
0
0
4
5
5
7
5
0
8
1
0
0
1
1
0
1
1
0
3
3
6
6
6
6
6
6
6
6
1
0

System Reference Guide

2
2
2
2
2
2
2
2
2
2
2
2
2
0
0
0
0
6
5
5
7
5
0
2
1
0
0
1
0
0
1
1
1
3
3
5
5
5
5
5
5
5
5
1
0

0
0
0
0
0
0
0
0
0
0
0
0
0
1
1
1
1
6
14
5
6
7
1
2
1
2
0
1
0
0
1
1
1
3
3
4
4
4
4
4
4
4
4
1
1

2
2
2
2
2
2
2
2
2
2
2
2
2
0
0
0
0
4
5
5
5
5
0
2
0
0
0
1
0
0
1
0
1
3
3
6
6
6
6
6
6
6
6
1
0

2
2
2
2
2
2
2
2
2
2
2
2
2
0
1
1
1
4
5
5
7
5
0
2
1
0
0
1
1
0
1
1
1
3
3
6
6
6
6
6
6
6
6
1
0

2
2
2
2
2
2
2
2
2
2
2
2
2
0
0
0
0
6
5
5
7
5
0
2
1
0
1
1
1
0
1
1
1
3
3
6
6
6
6
6
6
6
6
1
0

0
0
0
0
0
0
0
0
0
0
0
0
0
2
2
2
2
4
5
5
1
9
0
2
1
0
0
1
1
1
0
1
1
3
3
6
6
6
6
6
6
6
6
1
0

0
0
0
0
0
0
0
0
0
0
0
0
0
0
2
2
2
4
5
6
8
5
1
2
1
2
0
1
0
0
1
0
1
3
3
6
6
6
6
6
6
6
6
1
0

F01U087835 | 02 | 2008.10

110 en | Programming Details and Defaults

Easy Series

Country Codes
Prog Item# ↓

107
108
125
126
127
133
136
137
138
204
211
212
213
214
216
306
9011
9021
9031
9041
9051
9061
9071
9081
9012
9022
9032
9042
9052
9062
9072
9082
9092
9102
9112
9122
9132
9142
9152
9162
9172
9182
9192

5
5
3
60
30
1
0
0
0
1
0
0
0
0
000
0
6
1
1
1
1
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2

3
3
3
60
30
1
0
0
0
3
0
0
0
0
112
0
1
3
3
3
3
3
3
3
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0

3
3
3
60
20
3
0
0
0
3
0
0
0
0
000
0
6
1
1
1
1
2
2
2
2
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0

5
5
3
60
30
3
0
0
0
3
0
0
0
0
112
0
6
1
2
2
2
2
2
2
2
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0

5
5
3
60
30
1
0
0
0
1
0
0
0
0
000
0
6
1
1
1
1
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2

2
2
8
30
30
3
0
0
0
2
3
0
0
0
112
0
6
1
2
2
2
2
2
2
2
2
2
2
2
2
2
2
0
0
0
0
0
0
0
0
0
0
0

5
3
3
30
15
1
1
0
0
1
0
0
0
0
000
0
6
1
1
1
1
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2

5
5
3
60
45
3
0
0
0
1
1
1
0
0
000
1
6
1
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2

2
2
3
30
20
3
0
0
0
3
1
1
0
0
000
0
6
1
2
2
2
2
2
2
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0

5
5
0
60
30
1
0
0
0
3
0
0
0
0
110
0
6
1
1
1
1
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2

5
5
3
60
30
1
0
0
0
1
0
0
0
0
000
0
6
1
1
1
1
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2

15
15
0
45
45
4
0
0
0
3
5
5
5
0
000
0
1
8
3
3
3
3
2
2
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0

F01U087835 | 02 | 2008.10

System Reference Guide

3
60
30
3
0
0
0
3
0
0
0
0
112
0
6
1
2
2
2
2
2
2
2
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0

Bosch Security Systems, Inc.

Easy Series

Programming Details and Defaults | en 111

Country Codes
Prog Item# ↓

2
2
2
2
2
2
2
2
2
2
2
0
0
0
0
4
5
5
7
5
0
2
1
0
0
1
1
0
1
1
1
3
3
6
6
6
6
6
6
6
6
1
0

0
0
0
0
0
0
0
0
0
0
0
1
1
1
1
6
5
5
6
7
1
2
1
2
0
1
0
0
1
1
1
3
3
6
6
6
6
6
6
6
6
1
0

0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
4
5
5
5
5
1
2
1
0
0
1
0
0
0
1
1
3
3
6
6
6
6
6
6
6
6
1
0

0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
4
5
5
7
6
1
2
1
0
0
1
0
0
0
1
1
3
3
6
6
6
6
6
6
6
6
1
0

2
2
2
2
2
2
2
2
2
2
2
0
0
0
0
4
5
5
7
5
0
2
1
0
0
1
1
0
1
1
1
3
3
6
6
6
6
6
6
6
6
1
0

0
0
0
0
0
0
0
0
0
0
0
1
1
1
1
4
5
5
7
8
1
2
1
0
0
1
1
0
1
1
1
3
3
6
6
6
6
6
6
6
6
1
0

2
2
2
2
2
2
2
2
2
2
2
0
0
0
0
4
5
5
7
5
0
2
1
0
1
1
1
0
1
1
1
3
3
6
6
6
6
6
6
6
6
1
0

2
2
2
2
2
2
2
2
2
2
2
0
0
0
0
4
1
3
7
5
1
2
1
2
1
1
0
0
0
0
1
1
1
6
6
6
6
6
6
6
6
1
0

0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
4
5
5
7
5
1
2
1
0
2
1
0
0
1
1
1
3
3
6
6
6
6
6
6
6
6
1
0

0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
4
5
5
7
6
1
2
1
0
0
1
0
0
1
1
1
3
3
6
6
6
6
6
6
6
6
1
0

2
2
2
2
2
2
2
2
2
2
2
0
0
0
0
4
5
5
5
5
0
2
0
0
0
1
0
0
1
0
1
3
3
6
6
6
6
6
6
6
6
1
0

2
2
2
2
2
2
2
2
2
2
2
0
0
0
0
4
5
5
7
5
0
2
1
0
0
1
1
0
1
1
1
3
3
6
6
6
6
6
6
6
6
1
0

0
0
0
0
0
0
0
0
0
0
0
2
2
2
2
4
5
5
1
5
0
2
1
0
0
1
0
1
0
1
1
0
3
6
6
6
6
6
6
6
6
1
0

Bosch Security Systems, Inc.

System Reference Guide

F01U087835 | 02 | 2008.10

112 en | Agency Approvals and Requirements

Easy Series

Agency Approvals and Requirements

12.1

Certifications and Approvals
Compliance with specific standards, such as SIA CP-01 and DD243, reduces false alarms and
is required in many locations.
The Easy Series Intrusion Control Panel is designed to comply with the following
certifications, approvals, and standards:

–

ANSI/SIA CP-01 False Alarm Immunity

cUL Standards:
–

–
–

EN50131-1 Security Grade 2, Environmental Class II*

–

EN 50131-3, EN 50131-5-3, EN 50131-6, IP30 - IK04

System Control Units
–

DD243*

–

PD6662*

–

CCC*

–

UL Standards:
–

CAN/ULC-S545, Residential Fire Warning
System Control Units

(EN50529 - EN50102 )
–

CAN/ULC-S545, Residential Fire Warning

–

CAN/ULC-S303, Local Burglar Alarm Units and
Systems

–

C1076, Proprietary Burglar Alarm Units and
Systems

UL365, Police Station Burglar Alarm Units and
systems

–

UL609, Local Burglar Alarm Units and Systems

–

UL985, Household Fire Warning System Units

–

UL1023, Household Burglar-alarm System Units

–

UL1076, Proprietary Burglar Alarm Units and
Systems

–

C1023, Household Burglar Alarm Units

–

FCC

–

Industry of Canada (IC)

–

A-Tick*

–

C-Tick*

–

TBR21 for PSTN*

–

INCERT (Belgium) *

–

CSFM Listing - Control Unit Household

–

Japan Approvals Institute for Telecommunications
Equipment (JATE) *

* Not investigated by Underwriters Laboratories, Inc.

NOTICE!
The ITS-DX4020-G has not been tested by UL.

F01U087835 | 02 | 2008.10

System Reference Guide

Bosch Security Systems, Inc.

Easy Series

12.2

Agency Approvals and Requirements | en 113

FCC
Part 15
This equipment was tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is operated in a commercial
environment.
This equipment generates, uses, and can radiate radio frequency energy. If this equipment is
not installed and used according to this document, it might cause harmful interference to
radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference, in
which case the user must correct the interference.

Part 68
This equipment complies with Part 68 of FCC rules. A label contains, among other
information, the FCC registration number and ringer equivalency number (REN). If requested,
this information must be provided to the telephone company.
The Bosch Security Systems Easy Series Intrusion Control Panel is registered for connection
to the public telephone network using an RJ38X or RJ31X jack.
The REN determines the number of devices that can be connected to the telephone line.
Excessive REN's on the telephone line might result in the devices not ringing in response to an
incoming call. In most, but not all areas, the sum of the REN's should not exceed five. To
determine the number of devices that can be connected to the telephone line, contact the
telephone company for the maximum REN for the calling area.
The telephone company notifies you if this equipment harms the telephone network. If
advance notice is not practical, the telephone company notifies the customer as soon as
possible. Also, you are advised of your right to file a complaint with the FCC if you believe it is
necessary to do so.
The telephone company might make changes in its facilities, equipment, operation, or
procedures that could affect the operation of this equipment. If this happens, the telephone
company provides advance notice so you can make the necessary modifications for
maintaining uninterrupted service.
If you experience trouble with the Easy Series Intrusion Control Panel, contact Bosch Security
Systems Customer Service for repair and warranty information. If the trouble harms the
telephone network, the telephone company might request that you remove the equipment
from the network until the problem is resolved. User repairs must not be made, and doing so
voids the user's warranty.
This equipment cannot be used on public coin service provided by the telephone company.
Connection to party line service is subject to state tariffs. Contact your state public utilities
commission for more information.
–

FCC Registration Number: US:ESVAL00BEZ1; Ringer Equivalence: 0.0B

–

Service Center: Contact your Bosch Security Systems, Inc. representative for the
location of your service center.

Bosch Security Systems, Inc.

System Reference Guide

F01U087835 | 02 | 2008.10

114 en | Agency Approvals and Requirements

12.3

Easy Series

Industry Canada
This product meets the applicable Industry Canada technical specifications.
The ringer equivalence number (REN) for this terminal equipment is 0.0. The REN assigned to
each terminal equipment indicates the maximum number of terminals allowed to be
connected to a telephone interface. The termination of an interface can consist of any
combination of devices subject only to the requirement that the sum of the REN of all devices
does not exceed five.

12.4

SIA
Programming Requirements
To comply with ANSI/SIA CP-01 False Alarm Reduction, set these programming items as
follows:
Programming Item

Item Number

Default

Section Starting Page

Intrusion Abort Window

110

30 sec

Page 43

Intrusion Cancel Window

112

5 min

Exit Delay

126

60 sec

Entry Delay

127

30 sec

Swinger Bypass Count

131

Auto Protection Level

132

To comply with ANSI/SIA CP-01 False Alarm Reduction, by default, this system:
–
–

Sends Intrusion Alarm Verified and Exit Error reports
Sends a Recent Closing report for any alarm that occurs within two min of the end of Exit
Delay

–

F01U087835 | 02 | 2008.10

Includes a Fire Verified point type option that is disabled by default

System Reference Guide

Bosch Security Systems, Inc.

Easy Series

Agency Approvals and Requirements | en 115

Quick Reference
Refer to the following table for programmable features, shipping defaults, and recommended
programming that comply with the ANSI/SIA CP-01 False Alarm Reduction standard.
The system test button tests all points, all outputs, the control panel, and the communicator.
Refer to Section 8.1 Test the System, page 61 for more information.
Paragraph Number Feature

Requirement

Range

in ANSI/SIA CP-01
4.2.2.1

4.2.2.2

4.2.2.3
4.2.2.5

4.2.4.4

Exit Time

Shipping

Recommended

Default

Programming1
60 sec

60 sec

Required

For full or auto

(programmable)

arming: 45 sec to

Allowed

2 min (255 sec max)
Individual control
All control

All control centers

Annunciation/

centers can be

centers

enabled.

Disable for Silent

disabled.

enabled.

Progress

Exit
Exit Time Restart

Required Option

For re-entry during Enabled

Enabled

Auto Stay Arm on

Required option

Exit Time
If no exit after full

Enabled

Unvacated

(except for remote arm

Premises
Exit Time and

arm)
Allowed option (for Can be disabled for Enabled

Enabled

Progress

remote arm)

remote arm

Annunciation/
Disable for Remote
4.2.3.1

Arm
Entry Delay(s)

Required

30 sec to 4 min2

4.2.5.1

Abort Window for

(programmable)
Required option

Can be disabled by Enabled

Enabled (all

zone or zone type

zones)

4.2.5.1

Non-fire Zones
Abort Window Time Required

4.2.5.1.2

for Non-fire Zones (programmable)
Abort Annunciation Required option

15 sec to 45

sec2

30 sec

At least 30 sec2

30 sec

At least 15 sec2

Annunciate that no Enabled

Enabled

alarm was
4.2.5.4.1

Cancel

Required option

Annunciation
4.2.6.1 and 4.2.6.2 Duress Feature

transmitted
Annunciate that a

Enabled

Cancel was
Allowed Option

transmitted
No 1+ derivative of Disabled

Disabled

another user code;
no duplicates of
4.3.1

Cross Zoning

Required Option

other user codes
Programming

Disabled

Enabled and two

needed
4.3.1

Programmable

Allowed

Can program

Cross Zoning Time
4.3.2

Swinger Shutdown Required
(programmable)

4.3.2

For all non-fire

Per

programmed
Per walk path in

manufacturer

protected

One fault

premises
One fault

Enabled

Enabled (all

zones, shut down at

Swinger Shutdown Allowed

one or two faults
For non-police

Disable

response zones

Bosch Security Systems, Inc.

or more zones

System Reference Guide

zones)
F01U087835 | 02 | 2008.10

116 en | Agency Approvals and Requirements

Paragraph Number Feature

Easy Series

Requirement

Range

Shipping

Recommended

Required option

Default
Depends on control Disabled

Programming1
Enabled unless

Verification

panel and sensors

sensors can self-

Call Waiting Cancel Required option

Depends on user

in ANSI/SIA CP-01
4.3.3

4.5

Fire Alarm

verify
Enabled if user

Disabled

phone line

has call waiting

Programming at installation site might be subordinate to other UL requirements for the intended application.

Combined Entry Delay and Abort Window should not exceed 1 minute.

If the cross zone timer ends and a second cross zone point is not faulted, the system sends an intrusion alarm unverified report.

12.5

Underwriters Laboratories (UL)
Household Fire Warning System
–

Install at least one UL Listed four-wire latching type smoke detector rated to operate over
the voltage range of 11.2 VDC to 12.3 VDC. The maximum smoke detector load is 50 mA.

–

Install one UL Listed 85 dB audible device rated to operate over the range of 11.2 VDC to
12.3 VDC as required for this application. Program the bell cut-off time for at least four
minutes. Refer to Programming Item 107 in Section 5.2.2 System Programming Items,
page 43.

–

Install end-of-line resistor P/N: 47819 after last smoke detector.

–

Do not use a printer interface module.

–

Where two-wire addressable devices are used, do not place fire and intrusion devices on
the same zone.

–

The system must be able to operate for at least 24 hr, and generate a full alarm output for
at least 4 min without AC power.

Household Burglar Alarm Unit
–

Install at least one UL Listed 85 dB audible device rated to operate over the voltage range
of 11.2 VDC to 12.3 VDC.

–

Install at least one IUI-EZ1 Control Center.

–

Program all zones to use end-of-line supervision.

–

Install intrusion initiating devices rated to operate over the voltage range of 11.2 VDC to
12.3 VDC.

–
–

Program all intrusion zones for audible notification.
Do not exceed 60 sec when programming Exit Delay. Refer to Programming Item 126 in
Section 5.2.2 System Programming Items, page 43. Do not exceed 45 sec when
programming Entry Delay. Refer to Programming Item 127 in Section 5.2.2 System
Programming Items, page 43. Program the bell cut-off time for at least of four minutes.
Refer to Programming Item 108 in Section 5.2.2 System Programming Items, page 43.

–

The system must be able to operate for at least 24 hr, and generate a full alarm output for
at least 4 min without AC power.

F01U087835 | 02 | 2008.10

System Reference Guide

Bosch Security Systems, Inc.

Easy Series

Agency Approvals and Requirements | en 117

Commercial Burglary, Local
–

Use the D8108A Attack Resistant Enclosure with the D2402 Mounting Skirt.

–

Install at least one UL Listed 85 dB audible device rated to operate over the voltage range
of 11.2 VDC to 12.3 VDC. All wiring connections between the control panel and device
must be in conduit.

–

Do not exceed 60 sec when programming Exit Delay. Refer to Programming Item 126 in
Section 5.2.2 System Programming Items, page 43. Do not exceed 60 sec when
programming Entry Delay. Refer to Programming Item 127 in Section 5.2.2 System
Programming Items, page 43.

–
–

Install a tamper switch to protect the enclosure door.
Set Programming Item 116 to 1 (Daily) to ensure the automatic test report is sent on a
daily basis. Refer to Section 5.2.2 System Programming Items, page 43.

–

Ensure that the integrated communicator is enabled (Programming Item 304 = 0; refer to
Section Global Report Routing Items, page 52). Ensure that the system can send low
battery reports (Programming Item 358 = 1, 2, or 3; refer to Section System Report and
Restoral Routing, page 51).

–

Install at least one IUI-EZ1 Control Center.

–

Program the bell cut-off time for at least 15 minutes. Refer to Programming Item 108 in
Section 5.2.2 System Programming Items, page 43.

–
–

This system was not evaluated for Bank Safe and Vault applications.
The system must be able to operate for at least 24 hr, and generate a full alarm output for
at least 15 min without AC power.

Commercial Burglary, Police Station Connected Protected Premises*
–

Refer to Section Commercial Burglary, Local, page 117 for installation requirements.

–

Ensure that the integrated communicator is enabled (Programming Item 304 = 0; refer to
Section Global Report Routing Items, page 52).

* Systems are approved for Encrypted Line Security when used in conjunction with the C900V2 Conettix IP
Dialer Capture Module and communicating over a packet-switched data network (PSDN).

Commercial Burglary, Proprietary*
–

The integrated communicator is enabled (Programming Item 304 = 0; refer to
Section Global Report Routing Items, page 52).

–
–

The system has one owner.
The system must be able to operate without AC power for at least 24 hours. The central
station receiver must be able to receive reports without AC power for at least 24 hours.

* Systems are approved for Encrypted Line Security when used in conjunction with the C900V2 Conettix IP
Dialer Capture Module and communicating over a packet-switched data network (PSDN).

Bosch Security Systems, Inc.

System Reference Guide

F01U087835 | 02 | 2008.10

118 en | Agency Approvals and Requirements

12.6

Easy Series

PD6662 and DD243 Requirements
To comply with PD6662 and DD243, you must meet all of the EN50131-3 requirements and
the following requirements:
–

Maintenance: A qualified technician must check the system at least twice a year.

–

AC Power Supply:

–

Type: A

–

Rated Voltage: 230 V

–

Rated Input Frequency: 50 Hz

–

Rated Input Current: 250 mA maximum

–

Fuse Rating: 0.25 A, 250 V Slow Blow

Construction Materials: Enclosures and housings for the control panel, control center,
DX2010, wireless hub, and wireless devices are made from materials that are durable,
secure, and resistant to attack by hand-held tools.

–

Confirmed Alarms: Set Expert Programming Item Number 124 to either Option 3 or 4.
Refer to Section 5.2.2 System Programming Items, page 43for more information.

The Easy Series Intrusion Control Panel is designed to comply with PD6662:2004 as a Grade 2
system that supports Notification Options A, B, C, or X with the appropriate notification
devices installed (devices not included with system).

F01U087835 | 02 | 2008.10

System Reference Guide

Bosch Security Systems, Inc.

Easy Series

12.7

Agency Approvals and Requirements | en 119

EN50131 Requirements
The Easy Series Intrusion Control Panel is designed to comply with EN50131-1 Security Grade
2, Environmental Class II.

Installation, Programming, and Maintenance
Installation: Refer to Section 2.2 Install System Components, page 13.
Programming: Refer to Section 5 Programming, page 37.
Testing: Refer to Section 8 System Test and Maintenance, page 61.
Maintenance: Refer to Section 8 System Test and Maintenance, page 61.
Power Supply (AC and Standby Battery)
AC Power Supply: Refer to Section 10.2 Control Center, page 75.
Standby Battery: Refer to Section 10.2 Control Center, page 75.
Automatic Inhibit
Intruder Alarm and Fault Signal or Message: Set Expert Programming Item Number 131 to a value between 1 and 3.
Refer to Section 5.2.2 System Programming Items, page 43for more information.
Authorization Code: Set Expert Programming Item Number 892 to a value between 3 and 8.
Refer to Section 5.2.8 Control Center Programming Items, page 55for more information.
Logical and Physical Keys
Minimum Number of Combinations per User:
–

Passcodes: 15,625 (passcode length must be six digits)

–

Tokens: 42,000,000,000

–

Key Fobs: 2,800,000,000,000,000

Method Used to Determine Number of Combinations:
–

Passcodes: Digits 1 to 5 are allowed. For a six-digit passcode, all combinations are allowed.

–

Tokens: 32 bits. All combinations are allowed.

–

Key Fobs: 56 bits (48 serialized during manufacturing, 8 remain static)

Operating Temperature Range
Refer to Environmental Considerations on Page 72.
Control Panel and Control Center Current Consumption
Control Panel: Refer to Section 10.1 Control Panel, page 72.
Control Center: Refer to Section 10.1 Control Panel, page 72.
Output Current Rating
Refer to Programmable Outputs on Page 72.
To comply with EN50131-1, set these programming items as follows:
Programming Item

Item Number Setting

Section Starting
Page

Programming Key Auto Transfer

123

Select Option 0

Entry Delay

127

Set to 45 sec or less

Swinger Bypass Count

131

Select Option 3

Restrict Installer Passcode

142

Select Option 1

RPS Automatic Call In Frequency

224

Select Option 0

Page 49

Passcode Length

861

Set passcode length to six digits

Page 56

Bosch Security Systems, Inc.

System Reference Guide

Page 43

F01U087835 | 02 | 2008.10

120 en | Agency Approvals and Requirements

12.8

Easy Series

INCERT
To comply with INCERT, set these programming items as follows:
Programming Item

Item Number

Default

Section Starting Page

Restrict Installer Passcode

142

Page 43

Passcode Length

861

6 digits

Invalid Passcode Attempt

892

Control Center Lockout Time

893

Page 56

* To comply with INCERT, set these programming items to 3 or higher.

12.9

cUL
For Canadian installations, install systems according to ULC-S302. Systems that use the
C900V2 Conettix IP Dialer Capture Module meet Level 3 Line Security when communicating
over a packet-switched data network (PSDN).

12.10

NF A2P
If you modify system parameters you are responsible for maintaining the system within the
scope of the standard and regulations that apply to the hardware and/or the system in which
it is used. In a NF A2P compliant installation, use only NF A2P listed components, and check
that each parameter is in the authorized range.

Accessories Authorized in a Certified Installation
Part

Description

IUI-EZ1

Control Center

NP17-12IFR

17AH Yuasa Battery

ICP-EZPK

Flash memory

EZPS-FRA

Power supply for motion detectors and sirens

IPP-PSU-2A5

Supervised Auxiliary power supply

ICP-EZVM-FRF

Voice module in French

ISW-BHB1-WXFR

wLSN Hub

ISW-BK-F1-H5X

wLSN keyfob

ISW-BDL1-W11PHX

wLSN Tri-tech motion detector 11 x 11 m

ISW-BPR1-W13PX

PIR wLSN motion detector 12 x 12 m

ISW-BMC1-S135X

wLSN magnetic contact wLSN

ISW-BMC1-M82X

wLSN mini contact

ISW-BMC1-R135X

wLSN recessed contact

ISW-BIN-S135X

wLSN Choc and magnetic contact

ISW-BSM1-SX

wLSN smoke detector

ISW-BGB1-SAX

wLSN Glass break detector

ISW-BSR1-WX

wLSN sounder

ISW-BRL1-WX

wLSN output relay

DX2010

8 wire zones expansion board

F01U087835 | 02 | 2008.10

System Reference Guide

Bosch Security Systems, Inc.

Easy Series

Agency Approvals and Requirements | en 121

Siren Wiring in a NF A2P Certified Installation
Use only sirens with backup battery. Sirens which require a primary voltage of 14.4V can be
powered by the optional module EZPS-FRA, or the auxiliary power supply IPP-PSU-2A5.
Bring the hold-on +12V through panel PO1, set it as the interior siren, as shown on the siren
installation guide. Depending on the current requirement of the siren battery, the hold-on +
voltage can be taken from the orange terminal, white terminal, +14.4V of the siren power
output of optional board EZPS-FRA, or one of the outputs of auxiliary power supply IPP-PSU2A5.

NOTICE!
In a NF A2P certified installation, the power supply used to feed the battery of the siren shall
not be used to feed the motion detectors.

Motion Detectors Wiring in a NF A2P Certified Installation
Power for motion detectors shall be separated from power for sirens. Power for motion
detectors can either come from the white terminal + and -, or by the optional board EZPS-FRA
when the number of motion detector requires separate power lines, or by the auxiliary power
supply IPP-PSU-2A5.

Panel Configuration in a NF A2P Certified Installation
Check that each parameter is in the range of authorized values for NF A2P certified
installations.

Current Chart in a NF A2P Type 2 Certified Installation
To meet the 36 hours of backup power, check that the current required by all the equipments
used in the system is lower than the backup current available:
–

Max current in idle state: 465 mA (i.e. 270 mA of current for the panel , with one control
center)

–

Max current in alarm: 1000 mA (i.e. 675 mA of current for the panel, with one control
center)
Refer to the chart below.
Max Current in Idle State

Max Current In Alarm State

Module

I Max

Total

I Max

Easy Series Control Panel

85 mA

160 mA

Current for the panel: A
IUI-EZ1 Control Center (at least 1) 110 mA

Total
x1

....mA
x Qty

Current on the option bus: B

160 mA
...mA

165 mA

xQty

....mA

Motion detector(s)

x Qty

Siren(s)

x Qty

(Autre)

x Qty

Total aux current: C

...mA

Total A + B + C

...mA

Max backup current available, with a 17 AH battery (type 465 mA

1000 mA

2, 36H)

Bosch Security Systems, Inc.

System Reference Guide

F01U087835 | 02 | 2008.10

122 en | Agency Approvals and Requirements

Easy Series

Current Chart of the Aux Power Supply IPP-PSU-2A5
When the current required by additional components is higher than the backup current
available from the panel with the 17AH battery, add one or several auxiliary power supply IPPPSU-2A5.
The IPP-PSU-2A5 provides also the 14.5V output required by the siren batteries.
Max Current in Idle State

Max Current In Alarm State

Module

I Max

Total

I Max

IPP-PSU-2A5

55 mA

Total
x1

Detector(s)

x Qty

xQty

Siren(s)

x Qty

Control Center(s)

x Qty

Total aux current: C

...mA

Total in Idle State

...mA

Max backup current available, with a 17 AH battery

465 mA

55 mA

...mA
Total in alarm state

...mA
750 mA

The IPP-PSU-2A5 auxiliary power supply provide a protection against the deep discharge of the battery (active at idle state) and status
LEDs. This current has to be taken into account in the current chart.
Max. available current in idle state: 465 mA.
Max. current in alarm: 750 mA.

NOTICE!
For Aux power supply supervision, use an input from the panel or from a DX2010, with a two

resistors wiring (alarm and tamper)
–

Connect the output relay "trouble" from the aux power supply to a 24hr/24hr input.
Record the zone name with a text meaning "AC loss aux power supply"

–

On the tamper zone, connect the tamper contact of the aux power supply enclosure

Controller Recorder Wiring
To connect a controller / recorder, connect the coil inpu of the recorder to + and - of PO2,
PO3 and/or PO4.
Set the output as follows:
–

To record the state "arm unoccupied", set the output to "armed unoccupied"

–

To record the state "alarm", set the corresponding output to "intrusion and fire 2"
(reversed level)

Programming Items
To comply with NF A2P, set these programming items as follows:

F01U087835 | 02 | 2008.10

System Reference Guide

Bosch Security Systems, Inc.

Easy Series

Agency Approvals and Requirements | en 123

Programming Item

Item Number

NF A2P Approved Range Section Starting Page

Country Code

102

Enclosure Tamper Enabled

103

Fire Bell Cut-off Time

107

2 or 3

Intrusion Bell Cut-off Time

108

2 or 3

Intrusion Abort Window

110

Point Alarm Verification

124

Entry Delay

127

Shorter than Exit Delay

Page 43

Auto Protection Level

132

Latching Point and Enclosure Tamper

137

Latching System Device Tamper

138

Restrict Installer Passcode

142

Start Arming With Faulted Points

159

Passcode Length

861

Page 56

Circuit Style

9xx2*

Page 52

Response Time

9xx5*

4 or 5

* The middle digits = the point number. For example, "01" = Point 1, and "32" = Point 32.
Table 12.1 NF A2P Certified Configuration Values

NOTICE!
For supervised points (dual EOL), 2.2k Ω EOL resistors (P/N: 47819) required.

Bosch Security Systems, Inc.

System Reference Guide

F01U087835 | 02 | 2008.10

124 en | Agency Approvals and Requirements

Easy Series

Seal the Enclosure
1.

Open the pre-opened hole which is on the right of the enclosure.

Pass the sealing wire through this hole, and bring the two wires in the corresponding
hole of the enclosure door.

Seal the sealing lead as near as possible from the enclosure.

Figure 12.1 Enclosure Sealing

Enclosure

Sealing Location (pre-opened)

Right side of the enclosure

Right side of the door

Sealing lead

F01U087835 | 02 | 2008.10

System Reference Guide

Bosch Security Systems, Inc.

Bosch Security Systems, Inc.
130 Perinton Parkway
Fairport, NY 14450
(800) 289-0096
www.boschsecurity.com
© Bosch Security Systems, Inc., 2008

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : Yes
Page Mode                       : UseNone
XMP Toolkit                     : Adobe XMP Core 4.0-c320 44.293068, Sun Jul 08 2007 18:10:11
Producer                        : Acrobat Distiller 7.0 (Windows)
Creator Tool                    : FrameMaker 8.0
Modify Date                     : 2008:10:22 10:02:55-04:00
Create Date                     : 2008:10:22 09:58:43Z
Metadata Date                   : 2008:10:22 10:02:55-04:00
Format                          : application/pdf
Title                           : F01U087835-02 Easy Series 3 Ref Guide.book
Creator                         : fbj5fp
Document ID                     : uuid:12e645b9-7281-421c-b5bf-040931bba6fd
Instance ID                     : uuid:8346af65-23c2-45c2-83d5-60476ac077cf
Page Count                      : 126
Author                          : fbj5fp

EXIF Metadata provided by EXIF.tools

Bosch F01U087835 02 Easy Series 3 Ref Guide Quick Selection ( System Reference Guide) En US 2524758155

Navigation menu

Versions of this User Manual:

Views

Navigation