Bose 412568 802.11b/g and Bluetooth LE Wireless Module User Manual

Bose Corporation 802.11b/g and Bluetooth LE Wireless Module MANUAL AND LABELING REQUIREMENTS

a href="https://usermanual.wiki/Bose" itemprop="url"> Bose >

Manual.pdf

2.4GHz RF Modular Transceiver System Installation manual (draft v1)  1. Description  This document describes an RF transceiver module PCB having two independent radio transceivers. One radio complies to IEEE 802.11b/g protocols and the other to the Bluetooth Low Energy specification.  The module provided on-board power regulation and full shielding for the radio transceivers. 2.   The module consists of 2 separate circuits :   1) A 2.4GHz Wi-Fi RF transceiver IC and two PIF etch antennas.   2) A 2.4GHz Bluetooth Low Energy transceiver IC and one PIF etch antennas.  3. Cautions:  This equipment has been tested and found to comply with the limits for a Class B digital device,  pursuant  to  Part  15  of  the  FCC  Rules.  These  limits  are  designed  to  provide reasonable  protection  against  harmful  interference  in  a  residential  installation.  This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance  with the instructions, may cause harmful interference to radio communications.  However,  there  is  no  guarantee  that  interference  will  not  occur  in  a particular  installation.  If  this  equipment  does  cause  harmful  interference  to  radio  or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:  -  Reorient or relocate the receiving antenna. -  Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that     to which the receiver is connected. -  Consult the dealer or an experienced radio/TV technician for help.  This device complies with Part 15 of the FCC Rules. Operation is subject to the following two  conditions: (1)  This  device  may not  cause harmful interference, and  (2) this  device must  accept  any  interference  received,  including  interference  that  may  cause undesired operation.  Any  changes  or  modifications  not  expressly  approved  by  Bose  Corporation  could  void  the user's authority to operate this equipment.  WARNING! This module is to be installed only by Bose Corporation in its end products, and shall not be marketed to any other party.  This  RF  Module  has  been  certified  for  integration  into  products  without  further certification. However, Bose Corporation is still responsible for testing its end products for any additional compliance requirements required with this module installed (such as digital device emissions, PC peripheral requirements, etc.).
End Product Labeling This module is labeled with its own FCC ID and IC Certification Number. If the label is not visible when the module is installed inside another device, then the outside of the device into which this module is installed must also display a label referring to the enclosed module.  In that case, the final end product must be labeled in a visible area with the following:   “Contains Transmitter Module FCC ID: A94412568” “Contains Transmitter Module IC: 3232A-412568” or  “Contains FCC ID: A94412568”  “Contains IC: 3232A-412568”   IMPORTANT NOTE: In the event that these conditions can not be met (for certain configurations  or  collocation  with  another  transmitter),  then  the  FCC  and  Industry Canada  authorizations  are  no  longer  considered  valid  and  the  FCC  ID  and  IC Certification  Number  can  not  be  used  on  the  final  product.  In  that  case  the  end product  must  be  re-evaluated  to  obtain  separate  FCC  and  Industry  Canada authorizations.  In addition, Information regarding how to install or remove this RF module or change its RF related parameters should not be provided to the end user.  The user manual for the end product must include the following information in a prominent location:  “To  comply  with  FCC  and  Industry  Canada  RF  radiation  exposure  limits  for  general population/uncontrolled  exposure,  the  antenna(s)  used  for  this  transmitter  must  be installed  such  that  a  minimum  separation  distance  of  20cm  is  maintained  between  the radiator  (antenna)  and  all  persons  at  all  times.  In  addition  this  transmitter  must  not  be collocated or operating in conjunction with any other antenna or transmitter.”  This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.  Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.  Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication.  Conformément à la réglementation d'Industrie Canada, le présent émetteur radio peut fonctionner avec une antenne d'un type et d'un gain maximal (ou inférieur)
Download:
Mirror Download [FCC.gov]
Document ID2093064
Application IDslXQTYAThJ+OJ5OR9YSUlg==
Document DescriptionManual.pdf
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize26.01kB (325105 bits)
Date Submitted2013-10-17 00:00:00
Date Available2013-10-17 00:00:00
Creation Date2013-10-14 14:25:32
Producing SoftwareMicrosoft® Word 2010 Subscription
Document Lastmod2013-10-14 14:25:32
Document TitleMANUAL AND LABELING REQUIREMENTS
Document CreatorMicrosoft® Word 2010 Subscription
Document Author: Evan Gould
FCC ID Filing: A94412568

Navigation menu