Bose 412568 802.11b/g and Bluetooth LE Wireless Module User Manual MANUAL AND LABELING REQUIREMENTS

Download:
Mirror Download [FCC.gov]
Document ID	2093064
Application ID	slXQTYAThJ+OJ5OR9YSUlg==
Document Description	Manual.pdf
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	26.01kB (325105 bits)
Date Submitted	2013-10-17 00:00:00
Date Available	2013-10-17 00:00:00
Creation Date	2013-10-14 14:25:32
Producing Software	Microsoft® Word 2010 Subscription
Document Lastmod	2013-10-14 14:25:32
Document Title	MANUAL AND LABELING REQUIREMENTS
Document Creator	Microsoft® Word 2010 Subscription
Document Author:	Evan Gould

2.4GHz RF Modular Transceiver System
Installation manual (draft v1)
1. Description
This document describes an RF transceiver module PCB having two independent
radio transceivers. One radio complies to IEEE 802.11b/g protocols and the other to
the Bluetooth Low Energy specification. The module provided on-board power
regulation and full shielding for the radio transceivers.
2.
The module consists of 2 separate circuits :
1) A 2.4GHz Wi-Fi RF transceiver IC and two PIF etch antennas.
2) A 2.4GHz Bluetooth Low Energy transceiver IC and one PIF etch antennas.
3. Cautions:
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) This device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause
undesired operation.
Any changes or modifications not expressly approved by Bose Corporation could void the
user's authority to operate this equipment.
WARNING! This module is to be installed only by Bose Corporation in its end products,
and shall not be marketed to any other party.
This RF Module has been certified for integration into products without further
certification. However, Bose Corporation is still responsible for testing its end products
for any additional compliance requirements required with this module installed (such as
digital device emissions, PC peripheral requirements, etc.).
End Product Labeling
This module is labeled with its own FCC ID and IC Certification Number. If the label is not visible
when the module is installed inside another device, then the outside of the device into which
this module is installed must also display a label referring to the enclosed module. In that case,
the final end product must be labeled in a visible area with the following:
“Contains Transmitter Module FCC ID: A94412568”
“Contains Transmitter Module IC: 3232A-412568”
or
“Contains FCC ID: A94412568”
“Contains IC: 3232A-412568”
IMPORTANT NOTE: In the event that these conditions can not be met (for certain
configurations or collocation with another transmitter), then the FCC and Industry
Canada authorizations are no longer considered valid and the FCC ID and IC
Certification Number can not be used on the final product. In that case the end
product must be re-evaluated to obtain separate FCC and Industry Canada
authorizations.
In addition, Information regarding how to install or remove this RF module or change its
RF related parameters should not be provided to the end user.
The user manual for the end product must include the following information in a
prominent location:
“To comply with FCC and Industry Canada RF radiation exposure limits for general
population/uncontrolled exposure, the antenna(s) used for this transmitter must be
installed such that a minimum separation distance of 20cm is maintained between the
radiator (antenna) and all persons at all times. In addition this transmitter must not be
collocated or operating in conjunction with any other antenna or transmitter.”
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is
subject to the following two conditions: (1) this device may not cause interference, and
(2) this device must accept any interference, including interference that may cause
undesired operation of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux
appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions
suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de
l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est
susceptible d'en compromettre le fonctionnement.
Under Industry Canada regulations, this radio transmitter may only operate using an
antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry
Canada. To reduce potential radio interference to other users, the antenna type and its
gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not
more than that necessary for successful communication.
Conformément à la réglementation d'Industrie Canada, le présent émetteur radio
peut fonctionner avec une antenne d'un type et d'un gain maximal (ou inférieur)
approuvé pour l'émetteur par Industrie Canada. Dans le but de réduire les risques de
brouillage radioélectrique à l'intention des autres utilisateurs, il faut choisir le type
d'antenne et son gain de sorte que la puissance isotrope rayonnée équivalente
(p.i.r.e.) ne dépasse pas l'intensité nécessaire à l'établissement d'une communication
satisfaisante.
4. Markings
4.1 This module shall be identified with the following ID numbers on the radio
shields.
FCC ID : A94412568
IC
: 3232A-412568
4.2 End Product Labeling
The final end product which this module is used in must be labeled in a visible
area with the following:
"Contains FCC ID: A94412568 / IC:3232A-412568"
5. Connections
The following tables describe the connections to the module made via the four
connectors.
J1201
Pin #
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
15
14
13
12
11
10
Group
Name
Ethernet
Ethernet
Ethernet
Ethernet
Ethernet
Ethernet
Ethernet
Ethernet
Ethernet
Ethernet
Ethernet
Ethernet
USB
USB
USB
USB
USB
USB
USB
USB
USB
USB
USB
USB
AUX/TAP
AUX/TAP
AUX/TAP
AUX/TAP
AUX/TAP
AUX/TAP
AUX/TAP
J1203
Pin #
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
Group Name
Audio Out
Audio Out
Audio Out
Audio Out
Audio Out
Audio Out
Audio Out
Audio Out
Audio Control
Audio Control
Audio Control
Audio Control
SMPS, PA sync
SMPS, PA sync
Monitor Inputs
Monitor Inputs
Monitor Inputs
Monitor Inputs
Monitor Inputs
Audio Power
Smartspeaker
GND
Smartspeaker
User Interface
User Interface
GND
Misc
GND
Misc
Misc
Misc
Misc
Signal Name
AIC3256LRET\BASE
AIC3256LOUT
AIC3256RRET
AIC3256ROUT
EXTDACLRET
EXTDACLOUT
EXTDACRRET
EXTDACROUT
MUTEOUTN
AMPSTBYN
AMPFAULTN
AUDOUTBCLK (R1200)
GND
AUDIO_SYNC_OUT
(R1208)
IDIN
PAOFFSET1
PAOFFSET2
PWRMON
THERMISTOR
+5VA
UART0_RXD/IR_IN_T
GND
UART0_TXD
LED0
LED1
GND
I2C0_SCL
GND
I2C0_SDA
STATICIN
BATT_CHG_EN_L
DC_PRESENT_L
33
Power
PGND
Signal Name
34
Power
PPOS
35
36
37
38
39
40
Power
Power
Power
Power
Power
Power
PGND
PPOS
PGND
PPOS
PGND
PPOS
Signal Name
GND
TXP
TXN
LCMT
RXP
RXN
GND
(+)3.3V_ET
SPD_LED_AN
SPD_LED_CA
LKACT_LED_AN
LKACT_LED_CA
USB0_5V_FAULT_L
MICROB_DET
MICROB_SEL
USB0_DRVVBUS
USB0_ID
GND
USB0_DM
USB0_DP
GND
USB0_VBUS
USB0_VBUS
GND
AUX_LEFT
AUX_RETURN
AUX_RIGHT
GND
TAP_IN
TAP_OUT
GND
J1200
Pin #
Group
Name
10
GND
STROBE0
STROBE1
STROBE2
SWITCHIN0
SWITCHIN1
SWITCHIN2
GND
Ground
Button
Button
Button
Button
Button
Button
Ground
Button
Sense
Ground
GND
STATICIN
J1202
Pin #
12
11
10
Group Name
GND
LED
LED
OLED Power
IR_RECEIVER
Anode + Power
OLED Control
OLED Control
OLED Control
OLED Control
OLED Control
GND
Group Name
GND
LED0
LED1
OLED_17V
UART0_RXD/IR_IN
LED_5V
DISPCEN
DISPRESN
DISPDCN
SP1_SCLK
SPI2_DO
GND
6. General Electrical specifications
6.1 Power supply
5.0V +/- 5%
6.2 Power consumption
<5 Watts
6.3 Operational Temperature
0 ~ 45 C (non-condensing)
7. 2.4GHz BTLE RF Transceiver
The RF transceiver uses a TI CC2540 low cost, low power RF transceiver IC to drive
a 50 ohm etch antenna via a simple balun and matching network. A switched coaxial
connector is provided for test purpose to measure the output power from the IC and
balun
7.1 Electrical Specification
For a detailed description of the CC2540 and the most recent electrical
specification see the full vendor part spec SWRS084E available on TI web site:
http://www.ti.com/lit/ds/swrs084e/swrs084e.pdf
The module shall use the following settings :
7.1.1 RF Output Power :
+4dBm typical (measured at J801)
7.1.2 Useable Frequency Range:
2401.67 – 2482 MHz
7.1.3 Modulation
<1 Mb/sec GFSK with data
whitening
7.1.4 Channel Spacing
2 MHz
7.2 2.4GHz 802.11b/g RF Transceiver
The transceiver uses a proprietary and confidential chip set from SMSC
corporation for control and implementation of the IEEE 802.11b/g radio. A
DM870 control chip implements the transmission protocol and feeds I-Q
information to the company’s T6201C RF transceiver. For transmit, the RF path
includes a power amplifier SST12LP15A from Microchip.
The module shall use the following settings:
7.2.1 RF output power:
+11dBm typical (measured at CON4)
7.2.2 Useable frequency range:
2412 – 2462MHz (Western Hemisphere)
7.2.3 Modulation:
OFDM
7.2.4 Channel spacing:
5 MHz
7.3 Antenna Specification
The RF module uses three Planar Inverted F etch antennas, two in switched
diversity mode for Wi-Fi and one for Bluetooth Low Energy. The PCB layout
capture below shows their relative locations. The overall board dimensions are
225mm long by 37mm wide.
BTLE antenna
Wi-Fi antennas

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : No
Page Count                      : 6
Language                        : en-US
Tagged PDF                      : Yes
Title                           : MANUAL AND LABELING REQUIREMENTS
Author                          : Evan Gould
Creator                         : Microsoft® Word 2010 Subscription
Create Date                     : 2013:10:14 14:25:32-04:00
Modify Date                     : 2013:10:14 14:25:32-04:00
Producer                        : Microsoft® Word 2010 Subscription

EXIF Metadata provided by EXIF.tools