Bryant Tstatbbnq001 Users Manual
TSTATBBNQ001 to the manual f298d578-ecd8-403b-bd55-ae562784ede1
2015-02-02
: Bryant Bryant-Tstatbbnq001-Users-Manual-412173 bryant-tstatbbnq001-users-manual-412173 bryant pdf
Open the PDF directly: View PDF .
Page Count: 24
Download | ![]() |
Open PDF In Browser | View PDF |
USERS INFORMATION MANUAL Heating & Cooling Systems MODEL TSTATBBNQ001 NON-PROGRAMMABLE DIGITAL THERMOSTAT NOTE TO INSTALLER: This manual must be left with the equipment user. SINGLE STAGE HEAT & COOL THERMOSTAT 72 Heat Cool Thermostat Battery Operated 4-Wire Operation Millivolt Compatible Digital Display DC Voltage Compatible Stage: 1-Heat, 1-Cool Easy Slide Switch Operation Table Of Contents LOCATION OF CONTROLS 2 DISPLAY 4 NORMAL OPERATION 5 PREPARATION 6 REMOVE OLD THERMOSTAT 7 INSTALLATION AND BATTERY REPLACEMENT 8 WIRE CONNECTIONS 10 JUMPER CONFIGURATION 17 TEST OPERATION 20 TROUBLESHOOTING 21 WARRANTY 24 Bryant Heating & Cooling Systems Page 1 Patents Pending 4/03 Safety Warnings TSTATBBNQ001 CAUTION Follow Installation Instructions carefully. DISCONNECT POWER TO THE HEATER AIR CONDITIONER BEFORE REMOVING THE OLD THERMOSTAT AND INSTALLING THE NEW THERMOSTAT. WARNING CAUTION The 2 Alkaline “AA” batteries must be replaced at least every 12 months to assure proper operation. The thermostat will display the Low Battery code (fig. 1) on the display of the thermostat when it is time to replace the batteries. FIG. 1 When is displayed the batteries must be replaced immediately. The manufacturer cannot be liable for improper operation of the thermostat if the batteries are not immediately replaced. The annual battery replacement is especially critical in locations subject to freezing temperatures. The thermostat will be unable to turn on the Heat if the batteries are exhausted. This device complies with Part 15 of the FCC rules. Operation is subject to the following 2 conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Page 2 Location of Controls 72 MODE SWITCH Heat, Cool or Off UP & DOWN BUTTONS FAN SWITCH On or Auto Page 3 Display 78 74 SET TEMP Current room temperature. If the Up or Down arrow buttons are pressed the thermostat will show the desired Set Temp temperature indicator. Once this screen is reached you may use the Up or Down arrow buttons to adjust the desired room temperature. After five seconds with no button presses the thermostat will revert back to show the current room temperature. Page 4 Normal Operation 72 MODE SWITCH Heat, Cool or Off UP & DOWN BUTTONS FAN SWITCH On or Auto Manual Operation Select heat or cool with the mode switch. Normally leave the fan switched to auto. In fan auto, the fan will turn on only with a heat or cool demand. When Fan On is selected, the fan will run continuously, even when the mode switch is set to Off. Adjust the desired set temperature with the Up or Down buttons. Page 5 Step #1 72 Heat Off Cool Fan On FanAuto Proper installation of the thermostat will be accomplished by following these step by step instructions. If you are unsure about any of these steps, call a qualified technician for assistance. These tools will be required: 72 Heat Off Cool Preparation Fan On FanAuto Flat Blade Screwdriver 72 Heat Off Cool Fan On FanAuto 72 Heat Off Cool Fan On FanAuto 72 Heat Off Cool Fan On FanAuto Wire cutter & Stripper Make sure your Heater/Air Conditioner is working properly before beginning installation of the thermostat. Carefully unpack the thermostat. Save the screws and instructions. Turn off the power to the Heating/Air Conditioning system at the main fuse panel. Most residential systems have a separate breaker for disconnecting power to the furnace. Page 6 Step #2 72 Heat Off Cool FanOn FanAuto 72 Heat Off Cool FanOn FanAuto 72 Heat Off Cool FanOn FanAuto 72 Heat Off Cool FanOn FanAuto Remove & Replace Old Thermostat Remove the cover of the old thermostat. If it does not come off easily check for screws. Loosen the screws holding the thermostat base or subbase to the wall, and lift away. Disconnect the wires from the old thermostat. Tape the ends of the wires as you disconnect them, and mark them with the letter of the terminal for easy reconnection to the new thermostat. Keep the old thermostat for reference purposes, until your new thermostat is functioning properly. Page 7 Step #3 Installation and Battery Replacement To Open The Thermostat The top of the thermostat housing has two (2) screwSCREWDRIVER driver slots to assist when seperating. SLOTS To pull the housing apart, insert a small blade screwdriver into the slot and rotate 90 . This will release the top housing snaps. Repeat the procedure in the other screw driver slot. Separate the housing halves by pulling the top forward until the pins release, and then lift the bottom out. The batteries must be replaced immediately when the thermostat displays the Low Battery code (fig.1). Page 8 FIG. 1 Battery Replacement REPLACE WITH ALKALINE BATTERIES AT LEAST ONCE EVERY YEAR, OR WHEN THE “LOW BATTERY” APPEARS (pages 2,8). POSITION BATTERIES AS SHOWN USE “AA” SIZE ALKALINE BATTERIES USE “AA” SIZE ALKALINE BATTERIES FAN W/ HEAT J1 1 2 3 HEAT PUMP J2 3 2 1 Page 9 ICON Step #4 72 Heat Off Cool FanOn FanAuto Wire Connections If the terminal designations on your old thermostat do not match those on the new thermostat, refer to the chart below, or the wiring diagrams that follow. Function Install on the new thermostat connector marked W1, W or H Heating W Y1 or Y Cooling Rev. Valve Y Wire from the old thermostat terminal marked B (Energize to Heat) B O Rev. Valve O (Energize to Cool) G or F Fan G Rh, R, M, Vr, A Power R Thermal Insulating Sheet A label is provided on the backplate that prevents drafts, originating inside the wall, from entering the thermostat. These drafts, left unchecked, may cause incorrect room temperature readings. Please do not remove this label from the thermostat. Insert the wires through the slots provided in the label as shown in Fig. 1 Wire Slots Page 10 W Y B O G R MODEL: TSTATBBNQ001 4Z95 USE SIZE “AA” ALKALINE BATTERIES 97061606 MADE IN CHINA Fig. 1 Sample Wiring Diagrams 4 Wire, 1 Stage Cooling, 1 Stage Gas Heat Residential Gas or Electric Heat *, Electric Cool, split systems & package units W Y B O G R FAN G COOLING Y GAS OR ELECTRIC HEAT W POWER R 4 Conductor 18 to 22 gauge unshielded cable from the thermostat to the equipment. Page 11 Sample Wiring Diagrams 4 Wire, 1 Stage Cooling, 1 Stage Heat-Heat Pump with O reversing valve*. Residential Heat Pumps, split systems & package units, with no auxiliary heat. W Y B O G R REVERSING VALVE O COMPRESSOR Y FAN G POWER R 4 Conductor 18 to 22 gauge unshielded cable from the thermostat to the equipment. * For Heat Pump or Electric Heat applications see page 17 or 18 for Jumper configuration. Page 12 Sample Wiring Diagrams 4 Wire, 1 Stage Cooling, 1 Stage Heat-Heat Pump with B reversing valve*. Residential Heat Pumps, split systems & package units, with no auxiliary heat. W Y B O G R FAN G REVERSING VALVE B COMPRESSOR Y POWER R 4 Conductor 18 to 22 gauge unshielded cable from the thermostat to the equipment. * For Heat Pump or Electric Heat applications see page 17 or 18 for Jumper configuration. Page 13 Sample Wiring Diagrams 3 Wire, 1 Stage Heat Residential Gas or Electric Heat units with a separately controlled fan. W Y B O G R POWER R FAN G GAS OR ELECTRIC HEAT W 3 Conductor 18 to 22 gauge unshielded cable from the thermostat to the equipment. Page 14 Sample Wiring Diagrams 2 Wire, 1 Stage Gas Heat Residential Gas or Millivolt units. W Y B O G R POWER R GAS OR ELECTRIC HEAT W 2 Conductor 18 to 22 gauge unshielded cable from the thermostat to the equipment. Page 15 Sample Wiring Diagrams 3 Wire, 1 Stage Cooling Residential Electric Cool units W Y B O G R FAN G COOLING Y POWER R 3 Conductor 18 to 22 gauge unshielded cable from the thermostat to the equipment. Page 16 Step #5 Jumper Configuration Figure-A) FAN W/ HEAT J1 1 2 3 HEAT PUMP J2 3 2 1 72 Heat Off Cool Fan On FanAuto Jumper and Jumper are shown in the factory default positions for typical gas furnace heating with electric cooling. Cooling Mode Heating Mode OUTPUTS No Demand With Demand Y, G, O* O* W B* *Outputs active - For normal operation do not connect to equipment Page 17 Step #5 Jumper Configuration Figure-B) FAN W/ HEAT J1 1 2 3 HEAT PUMP J2 3 2 1 72 Heat Off Cool Fan On FanAuto Jumper is used to select Fan On (G) with Heat (W). Jumper shown in the factory default position. Cooling Mode Heating Mode OUTPUTS No Demand With Demand Y, G, O* O* W, G B* *Outputs active - For normal operation do not connect to equipment Page 18 Step #5 Jumper Configuration Figure-C) FAN W/ HEAT J1 1 2 3 HEAT PUMP J2 3 2 1 72 Heat Off Cool Fan On FanAuto Jumper and Jumper are used to select heat pump operation. Note: Thermostat Does Not Have Auxiliary Heat / Emergency Heat Capability. Leave jumpers in original factory default positions (figure-A) for non heat pump applications. Cooling Mode Heating Mode OUTPUTS No Demand With Demand Y, G, O* O* Y , G, B** B** * Output active in Cooling ** Output active in Heating Y active in Heating Page 19 Step #5 72 Heat Off Cool Fan On FanAuto 72 Heat Off Cool Fan On FanAuto 72 Heat Off Cool Fan On FanAuto 72 Heat Off Cool Fan On FanAuto Test Operation Turn on the power to the Heating/Air Conditioning system. Adjust the Slide Switch until it is located under the word HEAT on the thermostat. Press the Up or Down buttons until the set temperature is 10 degrees above room temperature. The HVAC unit should energize in the heating mode (pages 4-5). Adjust the Slide Switch until it is located under the word COOL on the thermostat. Press the Up or Down buttons until the set temperature is 10 degrees below room temperature. The HVAC unit should energize in the cooling mode (pages 4-5). Adjust the Slide Switch until it is located under the word OFF. Adjust the other slide switch until it is located under the word Fan On. The fan should turn on and run continuously (pages 4-5). Page 20 Troubleshooting 72 Heat Off Cool Fan On FanAuto 72 Heat Off Cool Fan On FanAuto SYMPTOM: The slide switches on the thermostat are very difficult to move. CAUSE: The backplate of the thermostat is deformed by being screwed tightly into a wall that is not perfectly flat. REMEDY: Loosen the screws holding the thermostat into the wall. SYMPTOM: The air conditioning does not attempt to turn on. CAUSE: The cooling setpoint is set too high or the Mode Switch is not set for Cool, or the batteries are too weak. REMEDY: Consult the Normal Operation section of this manual to lower the cooling setpoint and to correct the Mode Switch position, or replace the batteries (page 9). Page 21 Troubleshooting 72 Heat Off Cool Fan On FanAuto SYMPTOM: The heating does not attempt to turn on. CAUSE: The heating setpoint is set too low or the Mode Switch is not set for Heat, or the batteries are too weak. REMEDY: Consult the Normal Operation section in this manuals to raise the heating setpoint and to correct the Mode Switch position, or replace the batteries (Page 9). Battery Stat TSTATBBNQ001 c FC Tested to Comply with FCC Standards FOR HOME OR OFFICE USE 4Z95 Page 22 Warranty 5-Year Warranty - This Product is warranted to be free from defects in material and workmanship. If it appears within five years from the date of original installation, whether or not actual use begins on that date, that the product does meet this warranty, a new or remanufactured part, at the manufacturer’s sole option, to replace any defective part will be provided without charge for the part itself; PROVIDED the defective part is returned to the distributor through a qualified servicing dealer. THIS WARRANTY DOES NOT INCLUDE LABOR OR OTHER COSTS incurred for diagnosing, repairing, removing, installing, shipping, servicing or handling of either defective parts or replacement parts. Such costs may be covered by a separate warranty provided by the installer. THIS WARRANTY APPLIES ONLY TO PRODUCTS IN THEIR ORIGINAL INSTALLATION LOCATION AND BECOMES VOID UPON REINSTALLATION. LIMITATIONS OF WARRANTIES – ALL IMPLIED WARRANTIES (INCLUDING IMPLIED WARRANTIES OF FITNESS FOR A PARTICULAR PURPOSE AND MERCHANTABILITY) ARE HEREBY LIMITED IN DURATION TO THE PERIOD FOR WHICH THE LIMITED WARRANTY IS GIVEN. SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE MAY NOT APPLY TO YOU. THE EXPRESSED WARRANTIES MADE IN THIS WARRANTY ARE EXCLUSIVE AND MANY NOT BE ALTERED, ENLARGED, OR CHANGED BY ANY DISTRIBUTOR, DEALER, OR OTHER PERSON WHATSOEVER. ALL WORK UNDER THE TERMS OF THIS WARRANTY SHALL BE PERFORMED DURING NORMAL WORKING HOURS. ALL REPLACEMENT PARTS, WHETHER NEW OR REMANUFACTURED, ASSUME AS THEIR WARRANTY PERIOD ONLY THE REMAINING TIME PERIOD OF THIS WARRANTY. THE MANUFACTURER WILL NOT BE RESPONSIBLE FOR: 1. Normal maintenance as outlined in the installation and servicing instructions or owners manual including filter cleaning and/or replacement and lubrication. 2. Damage or repairs required as a consequence of faulty installation, misapplication, abuse, improper servicing, unauthorized alteration or improper operation. 3. Failure to start due to voltage conditions, blown fuses, open circuit breakers or other damages due to the inadequacy or interruption of electrical service. 4. Damage as a result of floods, winds, fires, lightning, accidents, corrosive environments or other conditions beyond the control of the Manufacturer. 5. Parts not supplied or designated by the Manufacturer, or damages resulting from their use. 6. Manufacturer products installed outside the continental U.S.A., Alaska, Hawaii, and Canada. 7. Electricity or fuel costs or increases in electricity or fuel costs from any reason whatsoever including additional or unusual use of supplemental electric heat. 8. ANY SPECIAL INDIRECT OR CONSEQUENTIAL PROPERTY OR COMMERCIAL DAMAGE OF ANY NATURE WHATSOEVER. Some states do not allow the exclusion of incidental or consequential damages, so the above may not apply to you. This warranty gives you specific legal rights, and you may also have other rights which may vary form state to state. Form No. OM17-55 Catalog No. 13TS-TA63 P/N 88-400 Rev. 2 Page 23
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.5 Linearized : Yes XMP Toolkit : 3.1-701 Producer : Corel PDF Engine Version 11.633 Keywords : Create Date : 2003:04:09 15:52:39Z Modify Date : 2005:11:10 11:05:18-05:00 Metadata Date : 2005:11:10 11:05:18-05:00 Creator Tool : CorelDRAW Version 11.0 Format : application/pdf Creator : Carrier Corporation Title : Description : Subject : Document ID : uuid:3fedf346-eee1-4857-b1a3-685d09f8282e Instance ID : uuid:777ca7c1-006d-4662-b160-0d99a1029a15 Page Count : 24 Author : Carrier CorporationEXIF Metadata provided by EXIF.tools