Bryton orporation BA1404 GPS Sports Watch User Manual 1
Bryton Incorporation GPS Sports Watch 1
Contents
- 1. User Manal_part 2
- 2. User Manal_part 3
- 3. User Manal_part 1
User Manal_part 1
bfy’ron‘ Amis 5430/5630 User’s Manual Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursu— ant to Part 15 of the FCC Rules, These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: . Reorient or relocate the receiving antenna. . increase the separation between the equipment and receiver. . Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. . Consult the dealer or an experienced radio/TV technician for help. FCC Caution: To assure continued compliance, any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. (Example — use only shielded interface cables when connecting to computer or peripheral devices). FCC Radiation Exposure Statement This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environe ment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmit— ter. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two condie tions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation b bry’ron' Table of Contents Getting Started 6 Your Amis 5430/5630 .................. 6 Accessories .................................. 7 Initial Setup...................... 7 Step 1: Charge the Battery Using the Computer ............... Using the Power Adapter (optional accessory).m...,.....,...,..._.,......_ Step 2:Turn On the Device Turn On/Off ........................... Step 3: Initial Setup ..................... 8 Step 4: Acquire Satellite Slgnals 9 ‘8 Step 5: Share Your Records ...... 10 Status Page 11 Icon Description .................. 11 Receiving GPS Signals ........... 12 Auto Time Calibration by GPS .. 13 Manually Set Time ............... . ..... 13 Set Alarm (Time1) 1 3 2 Amis 5430/5630 User's Manual Exercises 14 Starting an Exercise Running/Cycling. Triathlon (Amis 5630 only Multisport (Amis 5630 only) Outdoor Swim (Amis 5630 only). Pausel Stop Exercising......... Switch the Data Page ................ 16 Smart Pause 16 Lap 17 Smart Lap 1 7 Mark Lap 17 Train & Test 18 To Plan ............ Simple Workout Interval Workouts My Workout Bryton Workout. Bryton Test 21 Start Training ............................. 22 Stop Training 22 View History................... 23 View History 23 View Summary .................. Delete Exercise Records Tools 24 Metronome ................................ 24 Pace Calculator .......................... 25 Stopwatch .................................. 26 Countdown.................................................26 Stopwatch ~27 Notification 28 Settings 29 Exercises Settings ..................... 29 Customize the Data Display. .29 Set Alert .. .30 EnableTriathlon Transmon TIme (Amis 5630 only) ~30 Multisport Sequence Setup (Amis S630 only) -31 Watch Settings 32 Adjust Date ....... .32 Change Clock \fiew .32 General Settings........................ 32 Change Backlight Off Settings...........«.32 Enable Auto Key Lock (Amis 5630 only). ...-.. .... ... ...,............ .......33 Enable Key Vibrate (Amis 5630 only). .33 .33 Enable KeyTone ...... .... ... ....... Enable Vibrate (Amis 5630 only) .33 Enable Sound Alert... .34 Specify Unit ................ .......34 Specify the On Screen Display (05D) Language .34 Set GPS Mode Enable Bluetooth . Enable Race Mode Configure Auto Scroll (Amis 5630 only) ~35 Enable File Saving Mode. .36 Inverted Screen Color .. .36 .34 .35 .35 Adjust Contrast Level \fiew Memory Usage . About ....................... Sensors 38 Link Heart Rate Sensor... ...... .....38 Link Other Sensors (Amis“ S630 only) .38 Personalize User Profile............39 User Profile ........................... Bike Profile (Amis 5630 only) Troubleshooting 41 Getting More Information ........ 41 Reset Amis 5430/5630 .............. 41 Appendix.. 42 Glossary and Customizable Data Fields Selection ................ 42 Installing the Bike Mount (Amis 5630 only) ........................ 45 Installing the Heart Rate Monitor ...................................... 46 Wheel Size and Circumference ........................... 49 Heart Rate Zones ....................... 50 Basic Care For Your Amis S430] 5630 .. Specifications .. Amis 5430/5630 User‘s Manual 3 HSI1DN3 b bry’ron' @WARNING Always consult your physician before you begin or modify any training program. Please read the details in Warranty and Safety Information guide in the package. FCC Regulations 5 15.19 (a)(3) This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1 ) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. § 15.21 Changes or modifications not expressly approved by the party responsible for compliance could void the user‘s authority to operate the equipment. § 15.105 (b) This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.These limits are designed to provide reasonable protection against harmful interference in a residential installation.This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment offand on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. FCC RF Exposure Compliance This device is designed and manufactured not to exceed the emission limits for exposure to radio frequency (RF) energy set by the Federal Communications Commission for an uncontrolled environment. 4 Amis 5430/5630 User's Manual IC Regulations This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1 ) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d’lndustrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes: (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, méme si le brouillage est susceptible d'en compromettre |e fonctionnement. ***H***WHX'fififimfiaifiGeneral > Bluetooth > m Pairing. The OR code appears on the screen. b. Using your mobile phone, scan QR code shown on the device to _ _ download Bryton mobile app. Then install the Bryton mobile app on your mobile phone. c. On Amis 5430/5630, press ©/LAP and leave Amis device with the ”Waiting for pairing" message on the screen. 2. Sign up/Iog in on Bryton Mobile APP On your mobile device, launch Bryton mobile app. Then register a new account or use your current Bryton Account to log in. Activate the Bluetooth function on your mobile phone and enable the Bluetooth on the device. 4. Pairing your mobile phone with Amis 5430/5630 On Bryton mobile app, select Setting > Bluetth > Pairing. Once the Amis device appears on the list, select it to pair your mobile phone with the device. User profile Unlls Bluetooth . . . My Shoes Later, simply tap Sync With devrce, the workout records stored in Amis 5430/5630 will automatically sync to Bryton My We mobile app. About Lng out 10 Amis 5430/5630 User‘s Manual GPS signal status GPS positioning Status Notification Bike Type (Amis 5630 only) 60 Battery level Log recording Cadence sensor indicator (Amis 5630 only) Heart rate sensor indicator Icon Description GPS Signal Status Running mode Data page mode _ n a Fair” 9 Log recording in progress Bluetooth function is enabled -_ Normal ’7'“ Good Lock screen Power Status We El (6") Combo sensor active (Amis 5630 only) Battery charging 1 . Cycling mode (Amis 5630 only) Low batte ry Amis 5430/5630 User’s Manual 1 1 HSI'IDNE! b bry’ron' Receiving GPS Signals - Amis implements a status page to indicate current GPS signal strength. After position-fix is done, you can still check GPS status at data page by inspecting the icon located at up- right corner‘ Trip Tun! ( T Tnpl'me nip lime (2?; 00:31:00 0' =31=mia 00:31:00 (wing rural Dist. 01511 avail 0% >3 ®.@®EI ' 0% >8 9.@(DEI Cycling Total Dist. GPS signal is wealc GPS signal is normal. GPS signal is good. The satellite condition is Adequate for normal use. only sufficient for position» fix.This situation may not be sustained if your skyeview changes, such as going to the obstructed environments. - The best way to allow GPS get your position is to wearthe watch on your wrist. with the watch surface facing up‘ Please do not let the antenna facing down or cover it with hand. Inside rooms, Under water High-voltage Construction building, or wires or sites and heavy underground television traffic towers 12 Amis 5430/5630 User's Manual Display Screen Current date Current temperature Time 1 Lock screen icon (local time) Time 2 Alarm icon (alternate time) Notification icon Auto Time Calibration by GPS 1. Press V to enter the menu mode. 2. Press A/V to select Settings > Watch > Time > By GPS and press @/ LAP to enter its submenu. 3. Press A/V to set the daylight saving time and press (9/ LAP to confirm. — Afl' Daylight Saving Manually Set Time 1. Press V to enter the menu mode. 2. Press A/V to select Settings > Watch > Time > Manual > SetTime 1 or Set Time 2 and press @ILAP to enter its submenu. Set T1 mei Set Time2 Off 3. Press A/V to select the desired setting and press @/ LAP to confirm. Set Alarm (Time1) mean- 1. Press V to enter the menu mode. Set Alarm 2. Press A/V to select Settings > Watch > Alarm > Set Alarm . AM 08‘ OO and press (9/ LAP to enter its submenu. SWItch 3. PressA/V to select the desired setting and press (9/ LAP to confirm. On Amis 5430/5630 User’s Manual 13 HSI'IDNE! b bry’ron' Starting an Exercise Amis 5430 11:14 All 16/04 El To start an exercise, press A/V to select Running.Then press ©/ LAP Exercise to start. Train & Test View Histroy Amis $630 To start an exercise, press A/V to select Exercises > Running, Cycling, Triathlon, Multisport, Outdoor Swim, or 0thers.Then press ©l LAP to start. CYCIinQ Swimming Triathlon Exercises R u n n i n g Running/Cycling Select Running/Cycling and press (9/ LAP to start exercise. Triathlon (Amis 5630 only) - The exercise information will be displayed as following order: Swimming > Cycling > Running. Press @/ LAP to switch to the second or third sport. - To add the transition time, refer to Enable Mathlon Transition Time on page 30. 14 Amis 5430/5630 User‘s Manual mpnme 00= 30= 00 Toiil DISL Multisport (Amis 5630 only) - During the Multisport exercise and the mode setting is set to Manual, press A/V select the desired sport (Running, Cycling, or Swimming) and press ©/LAP to confirm.Then press ©/ LAP to start exercise. TrlpTlme 00- 31' 00 Cycling Toul DkL - To switch to the second sport, press ©l LAP to display the menu option. To preset the sports sequence in Multisport mode, refer to Multisport Sequence Setup on page 31. TripTIme 00= 31= 00 Tml Dist, Outdoor Swim (Amis 5630 only) Select Outdoor Swim and press (9/ LAP to start exercise. Ex TIME 00= 30= 00 Speed Trip Time 00= 40= 00 running Total DISL 6.73 m (I) Amis 5430/5630 User’s Manual 15 HSI'IDNE! b bry’ron' Pause/ Stop Exercising Press DI =I I to pause the recording and press again to stop 90'3““: “7"“ o 5 up the recording. Switch the Data Page When you start an exercise. the data view appears on the screen.The Data Page displays information varies based on your personal setting. Run Time fi Run Time 01:05:57 Sunset 18=43=47 at}: >8 6.@®m 2—grid display 3-grid display 4—grid display To customize the data page, refer to Customize the Data Display section on page 29. Press V to switch data screen page. However if the Auto Scroll feature is enabled, the data view will automatically switch pages at the preset time. To enable the Auto Scroll feature, refer to ConfigureAuto Scroll section on page 35. Smart Pause When you have a lot of obstacles along your route such as traffic lights, crosswalk, etc, this can really impact your recorded data. When the function is activated, the time and distance will automatically pause once you stop moving and resume once you start riding to enhance your data efficiency. Enable 1. Press V to enter the menu mode. 2. Press A/V to select Settings > Exercises > Running, Cycling, Outdoor Swim, or Others > Smart Pause and press ©ILAP to enter its submenu. 3. Select Yes to enable the function. 16 Amis 5430/5630 User‘s Manual Smart Lap Smart lap can automatically mark laps based on a defined distance or location. Whenever you reach the distance or pass the location, the device will trigger a lap marking. - Distance: to mark laps based on a defined distance, such as every kilometer or every mile. - Location: to mark laps based on a given position. Good for a course or route where you pass the same location over and over again. M312 Smart Lap 1. Press V to enter the menu mode. - 2. Press A/V to select Settings > Exercises > Smart Lap > Distance or Location and press (9/ LAP to enter its submenu. A Location V 3. Set the training target and press (9/ LAP to confirm. Amis 5630 1. Press V to enter the menu mode. 2. Press A/V to select Settings > Exercises > Running. Cycling, or Others > Smart Lap > Distance or Location and press (9/ LAP to enter its submenu. 3. Set the training target and press @lLAP to confirm. Mark Lap To mark a lap, do the following: Amis 5430 L Start an activity first by pressing ©/LAP . While recording, press ap 5 ©/LAP to mark |ap.When using Lap, the Lap screen will be 00:40'0-0' displayed while you are doing exercise or training. Angace 05:50/km Amis 5630 Total 03:18:57 1. Press V to enter the menu mode. 2. Press A/V to select Settings > Exercises > Running, Cycling, or Others and press ®/ LAP to enter its submenu. 3. While recording, press @lLAP to mark lap. When using Lap, the Lap screen will be displayed while you are doing exercise or training. Amis 5430/5630 User’s Manual l7 HSI'IDNEI b bry’ron' To Plan The device offers you with two types of workouts: Simple and Interval. Simple Workouts There are three types of simple workouts: ByTime, By Distance, and By Calories. 1. Press V to enter the menu mode. 2. Press A/V to select Train &Test and press @/ LAP to enterTraining menu. 3.To set a simple workout, select To Plan > Simple > Warm Up, Work, orCooldown. - Warm Up: Duration (manual, calorie,time, distance), Target (Pace, HR, MHR, LTHR). . Worlc 6'0" 143-1130an Duration (calorie. time,distance), Target (Pace. MHR%, LTHR%, HR, MHR, LTHR, Off). - Cooldown: Duration (manual, calorie,time, distance), Target (Pace, HR, MHR, LTHR). 4. Set the training target and press (9/ LAP to confirm. 5. Choose Save and press A/V to enter the workout name. M When finishing the name, press D/=/I to save the i Save in my workout name. Workout? Yes 18 Amis 5430/5630 User‘s Manual Interval Workouts With the Interval training feature, you can use your device to customize interval workouts which include the warm up, interval, and cool down sections. 1. Press V to enter the menu mode. 2. Press A/V to select Train &Test and press ®/LAP to enterTraining menu. NOT E- On Amis 5630, select Train &Test > Running or Cycling. 3.To set an interval workout, select To Plan > Interval. 4. A “Set warm up?" message appears on the screen. Select Yes to set the “Warm up". After the settings are complete, select OK and press O/LAP to continue. 5. Set the interval workout settings (Work, Recovery, and Repeat Time). When finished, press A/V to select Next and press (9/ LAP to continue. 6. A”Create a new main set?" message appears on the screen. To create another set of interval workout, select Yes and press ©/ LAP 7. A”Set cool down?" message appears on the screen. Select Yes to set the ”Cool down". After the settings are complete, select 0K and press ©/ LAP to continue. Warm Up Target OK Work 1 Recovery 2'00" 137~149bpm to confirm. Cooldown Target OK 8. A “Save to My Workout" message appears on the screen. Select Yes and press ®l LAP to continue. Press A/V to enter the workout name. When finishing the name, press D/=/ I and press ©/LAP to savethe workout. Amis 5430/5630 User‘s Manual 19 HSI'IDN3
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.6 Linearized : Yes Author : TEST Create Date : 2014:07:21 15:53:22+08:00 Modify Date : 2014:07:21 15:53:28+08:00 XMP Toolkit : Adobe XMP Core 5.4-c005 78.147326, 2012/08/23-13:03:03 Metadata Date : 2014:07:21 15:53:28+08:00 Creator Tool : PScript5.dll Version 5.2.2 Format : application/pdf Title : 組合 1.pdf Creator : TEST Document ID : uuid:baf48533-eeeb-4304-a999-10d3a319c799 Instance ID : uuid:a8c14db2-641f-46dc-8682-ac924dd01858 Producer : Acrobat Distiller 11.0 (Windows) Page Count : 20EXIF Metadata provided by EXIF.tools