Building Robotics FS-D2 Intelligent Light Sensor for Smart Networked Energy Saving Lighting Systems User Manual PhysicalInstall
Enlighted, Inc. Intelligent Light Sensor for Smart Networked Energy Saving Lighting Systems PhysicalInstall
Users Manual
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 2456805 |
| Application ID | Fy4jpu3HDdR3LdclSS2vQQ== |
| Document Description | Users Manual |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 23.93kB (299132 bits) |
| Date Submitted | 2014-11-26 00:00:00 |
| Date Available | 2014-12-02 00:00:00 |
| Creation Date | 2014-10-16 16:10:13 |
| Producing Software | Microsoft® PowerPoint® 2013 |
| Document Lastmod | 2014-10-16 16:10:13 |
| Document Title | PhysicalInstall |
| Document Creator | Microsoft® PowerPoint® 2013 |
| Document Author: | David Perkins |
Cautionary Suggestions • Disconnect all power before installation or service. • Installation and maintenance must be performed by qualified personnel. Fixture Mount DALI Sensor (D2) Installation Instructions • Installations and maintenance must be performed in accordance with state, local, and national electrical codes and requirements. Installation Steps This installation assumes that you have already installed the DALI LED driver. Step Figure 1: Fixture Mount DALI Sensor Shipped Components • DALI Sensor (D2) Tools You May Need Turn off all power to the light fixture by switching off the circuit breaker. The face of the sensor is only 1.08 inches (27mm) in diameter and is designed to mount in a ½ inch trade size (0.875 inch) hole.. (All parts of the sensor are inside the lighting fixture except for a ring and spring.) Determine the location for the sensor in fixture, and either remove an existing ½ inch knockout or cut a hole in the fixture. Orient the sensor and measure the length between it and the LED driver “DALI connections”, and cut two lengths of 18 AWG wire that are at least this length plus 1 inch. Strip each end of the 2 wires leaving 3/8 inch of exposed wire. Insert one end of the wires in the sensor’s wire holes and the other in the DALI LED driver “DALI connections” wire holes Remove (by unscrewing) the outer ring from the sensor (saving the ring and pressure spring). On the inside of the fixture, insert the sensor in the hole in the fixture and on the outside of the fixture, replace the spring and screw back on the outer ring. Tighten firmly, but do no over tighten. • Wire cutter and stripper Figure 2: Mechanical dimensions of the DALI Sensor Description Figure 3: Wiring Diagram Ready the fixture for use, and when done, restore power to the fixture. Supplies You May Need • 18 AWG Solid Copper Wire, rated >=300VPage 1 Page 2 Page 3 FCC and Industry Canada Compliance Information This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. USA This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: • this device may not cause harmful interference, AND • this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by Enlighted Inc. could void the user's authority to operate the equipment. Canada This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: • this device may not cause harmful interference, AND • this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by Enlighted Inc. could void the user's authority to operate the equipment. Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes: • l'appareil ne doit pas produire de brouillage, ET • l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement. Copyright © 2014 Enlighted Inc. All rights reserved. All other brand or product names are trademarks of their respective companies or organizations. Technical Support For questions regarding the installation or operation of this product, contact Enlighted Technical Support: support@enlightedinc.com Company Contact Information Location: 930 Benecia avenue, Sunnyvale, CA 94085 Phone: +1.650.964.1094 Web: enlightedinc.com CA Contractor’s License: CCL# 980903 Model: FS-D2 FCC ID: AQQ-FS-D2 Industry Canada: 10138A-FSD2 Page 4 Page 5 Page 6
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : No Page Count : 2 Language : en-US Tagged PDF : Yes XMP Toolkit : 3.1-701 Producer : Microsoft® PowerPoint® 2013 Title : PhysicalInstall Creator : David Perkins Creator Tool : Microsoft® PowerPoint® 2013 Create Date : 2014:10:16 16:10:13-07:00 Modify Date : 2014:10:16 16:10:13-07:00 Document ID : uuid:DFC47C0E-FC7E-4DCF-87AE-0DFA8083626C Instance ID : uuid:DFC47C0E-FC7E-4DCF-87AE-0DFA8083626C Part : 1 Conformance : A Author : David PerkinsEXIF Metadata provided by EXIF.tools