BuildingLink HPBU01 RF transceiver module User Manual HPBU01 TR 915 20180425

Download:
Mirror Download [FCC.gov]
Document ID	3844674
Application ID	YvZqaMky1Bbh4M5spD3AQQ==
Document Description	Users manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	34.82kB (435256 bits)
Date Submitted	2018-05-09 00:00:00
Date Available	2018-05-09 00:00:00
Creation Date	2018-04-25 11:43:35
Document Lastmod	2018-04-25 11:43:35
Document Title	HPBU01-TR-915 20180425
Document Creator	Doro PDF Writer [1.90] [http://j.mp/the_sz]

RF transceiver module
HPBU01-TR-915
Datasheet
BuildingLink
85 5th Ave 3rd
New York NY 10003
HPBU01-TR-915
1.
Datasheet
Introduction
The HPBU01-TR-915 is a compact, low power, bidirectional transceiver module in the
915 MHz range utilizing Sub-GHz technology. The module provides long range and high
output power while also reducing current consumption to a minimum. The HPBU01-TR915 also utilizes the widely used ATmega328P processor. The coupling of Sub-GHz
transceiver technology and ATmega328P processor allows for faster prototyping and
fast time to market. The HPBU01-TR-915 module utilizes a patch antenna to reduce the
need for RF development and antenna tuning and provide consistent range
expectations.
Figure 1-1: Picture of HPBU01-TR-915
Specifications
Sub-GHz Transceiver
902 MHz – 928 MHz Frequency
Range
Built in AES-128 encryption
Down to -120 dBm at 1.2kbps
sensitivity
Programmable output to +20 dBm
(100mW)
UART, SPI, and I2C interface
Customizable GPIO for analog /
digital signals
ATmega328P Co-Processor
Supply voltage range from 2.4v to
3.6v
Application
Wireless Sensor Networks
Home and Building Automation
Wireless Alarm and Security
Systems
Meter Reading
Remote Control
Telemetry
Environmental Alerts
HPBU01-TR-915
Datasheet
2. Electrical Characteristics
2.1 Absolute Maximum Ratings
Absolute maximum values should not be exceeded or sustained for a long period of time.
Failure to comply may result in damaging the module.
2.2 Operating Range
HPBU01-TR-915
2.3 Power Consumption
Datasheet
HPBU01-TR-915
Datasheet
3. Module Package
The pinout and recommended footprint for designing around the HPBU01-TR-915 module is
defined below for east integration and implementation.
3.1 Pinout Description
HPBU01-TR-915
PIN
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
PIN Name
GND
CS1
PB1
CS2
PD7
MOSI
MISO
SCK
PD6
PD5
DIO0
DIO1
DIO2
DIO3
DIO4
DIO5
3.3V-RF
3.3V-MCU
GND
RF-REST
PC1
PC2
PC3
PC4
PC5
REST
PD0
PD1
PD2
PD3
PD4
Datasheet
Pin Type
Supply
D IN/OUT
D IN/OUT
D IN/OUT
D IN/OUT
D IN/OUT
D IN/OUT
D IN/OUT
D IN/OUT
D IN/OUT
D IN/OUT
D IN/OUT
D IN/OUT
D IN/OUT
D IN/OUT
D IN/OUT
Supply
Supply
Supply
D IN
D IN/OUT, A IN
D IN/OUT, A IN
D IN/OUT, A IN
D IN/OUT, A IN
D IN/OUT, A IN
D IN
D IN/OUT
D IN/OUT
D IN/OUT
D IN/OUT
D IN/OUT
MCU Pin
PB2
PB1
PB0
PD7
PB3
PB4
PB5
PD6
PD5
DIO0
DIO1
DIO2
DIO3
DIO4
DIO5
REST
PC1
PC2
PC3
PC4
PC5
PC6
PD0
PD1
PD2
PD3
PD4
Description
Ground Connection
DIGITAL IO / SPI NSS
DIGITAL IO
DIGITAL IO
DIGITAL IO
DIGITAL IO / SPI MOSI
DIGITAL IO / SPI MISO
DIGITAL IO / SPI SCK
DIGITAL IO
DIGITAL IO
RF IO Pin
RF IO Pin
RF IO Pin
RF IO Pin
RF IO Pin
RF IO Pin
Supply Voltage
Supply Voltage
Ground Connection
Reset Pin for RF69
DIGITAL IO / ADC
DIGITAL IO / ADC
DIGITAL IO / ADC
DIGITAL IO / ADC
DIGITAL IO / ADC
Reset Pin for MCU
DIGITAL IO / RX
DIGITAL IO / TX
DIGITAL IO / INT0
DIGITAL IO / INT1
DIGITAL IO
HPBU01-TR-915
3.2 Recommended Footprint
Datasheet
FCC WARNING:
WARNING:
This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may
cause undesired operation.
Any changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate the equipment.
NOTE:
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generate, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation.
If this equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
-- Consult the dealer or an experienced radio/TV technician for help.
To maintain compliance with FCC’s RF Exposure guidelines, this equipment should be
installed and operated with minimum distance between 20cm the radiator your body:
Use only the supplied antenna.
FCC ID: 2APA52APA5-HPBU01

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.3
Linearized                      : No
Page Count                      : 8
Creator                         : Doro PDF Writer [1.90] [http://j.mp/the_sz]
Create Date                     : 2018:04:25 11:43:35+08:00
Modify Date                     : 2018:04:25 11:43:35+08:00
Title                           : HPBU01-TR-915 20180425
Subject                         : HPBU01-TR-915 20180425
Author                          : 
Producer                        : 
Keywords                        : HPBU01-TR-915, 20180425

EXIF Metadata provided by EXIF.tools