CARRIER Controls And HVAC Accessories Manual L0801202
User Manual: CARRIER CARRIER Controls and HVAC Accessories Manual CARRIER Controls and HVAC Accessories Owner's Manual, CARRIER Controls and HVAC Accessories installation guides
Open the PDF directly: View PDF 
.
Page Count: 10
| Download | |
| Open PDF In Browser | View PDF |
Installation
Instructions
FIRE,
EXPLOSION,
CARBON
MONOXIDE
Failure to follow
injury or death.
NOTE:
Read
installation.
Installing
the entire
instruction
manual
before
SAFETY
CONSIDERATIONS
and servicing
heating
equipment
starting
can be hazardous
the
due
to gas and electrical components.
Only trained
and qualified
personnel should install, repair, or service heating equipment.
Untrained
such as
personnel
can perform
cleaning
and replacing
basic maintenance
functions
air filters. Trained
service
personnel
must perform all other operations.
When working
on
heating equipment,
observe precautions
in the literature, on tags,
and on labels attached to or shipped with the unit, and other
safety precautions
Follow
codes.
In the United
the National
Z223.1-2006.
States.
follow
Codes
/_.
safety
When
are used
you
information.
see
or manuals,
Understand
and NOTE.
result
in personal
this
This
is the safety-alert
symbol
be alert
on
the
furnace
to the potential
INTRODUCTION
symbol
and
This instruction
covers
the installation
in
for personal
of gas conversion
No. KGANP4301STM
to convert the following
natural gas usage to propane gas usage:
Models 58MVC
and 355CAV
Ignition,
Variable-Speed.
Wear safety glasses and work gloves. Have a fire extinguisher
available during start-up, adjustment steps, and service calls.
instructions
injury.
could
AND
This conversion
kit shall be installed by a qualified service
agency in accordance
with the manufacturer's
instructions
and all applicable codes and requirements
of the authority
having jurisdiction.
If the information
in these instructions
is not followed exactly, a fire, explosion,
or production
of
carbon
monoxide
may result causing
property
damage,
personal injury, or loss of life. The qualified service agency
is responsible
for the proper installation
of this furnace with
this kit. The installation is not proper and complete until the
operation of the converted appliance is checked as specified
in the manufacturer's
instructions supplied with the kit.
all safety
Fuel Gas Code (NFGC) NFPA No.
In Canada, refer to the National
Standard of Canada, Natural Gas and Propane Installation
(NSCNGPIC),
CAN/CGA-B149.1
and .2-M05.
Recognize
this warning
SHOCK,
HAZARD
that may apply.
all safety
codes including
54-2006/ANSI
ELECTRICAL
POISONING
4-Way Multipoise.
Step-Modulating,
from
Hot Surface
Condensing
Furnaces.
This kit is designed for use in furnaces
through 120,000 Btuh gas input rates.
This kit is designed for use in the furnaces
valve will be a White-Rodgers.
kit Part
furnaces
with 60,000
listed above.
The gas
SHOCK
HAZARD
AND
the signal words DANGER,
WARNING.
CAUTION
The words DANGER,
WARNING,
and CAUTION
with
the safety-alert
symbol.
DANGER
identifies
the
most serious hazards which will result in severe personal injury or
death. WARNING
signifies
a hazard which could
result in
personal injury or death. CAUTION
is used to identify unsafe
practices which may result in minor personal injury or product
and property
damage. NOTE is used to highlight
suggestions
which will result in enhanced
installation,
reliability,
or operation.
FIRE,
EXPLOSION,
CARBON
MONOXIDE
ELECTRICAL
POISONING
Failure to follow
this warning
injury, death or property damage.
could
result
in personal
Improper
installation,
adjustment,
alteration,
service.
maintenance, or use can cause carbon monoxide
poisoning,
explosion, fire, electrical shock, or other conditions,
which
could result in personal
injury or death. Consult
your
distributor
or branch for information
or assistance.
The
qualified
installer
or
agency
factory-authorized
kits or accessories
product.
nmst
when
use
servicing
only
this
Table
1-
Kit Contents
DESCRIPTION
PART NO.
Main Burner Orifice (Drill Size 1.25 mm)
QUANTITY
LH32DB209
7
327593-401
323184-301
7
1
Low Gas Pressure Switch (Propane) (LGPS)
HK02LB008
1
Nipple
CA52JZ103
1
90 ° Street Elbow (1/8 in.)
CA15RA001
1
Male X Female X Female Tee (1/8 in.)
CA21JZ001
1
1
Screw, Spoiler DO NOT USE
Diverter Plate
Splice Connector
(1/4 in. Male, Both Ends)
66175D55
Splice Connector
(3/16 in. Male, Both Ends)
HY89SC047
1
W182X23
04 018
HY76TB125
2
1
Orange Wire Assembly (18 in.)
Wire Tie
Conversion
Rating Plate Label
Conversion
Condensing
Responsibility
Furnaces
Gas Control Conversion Label (adjusted)
Installation Instructions
Regulator Spring Kit (White Propane-EF39W023)
Rodgers 36J Valve
DESCRIPTION
This kit is designed
AND
for use in the furnaces
333583-201
1
333583-203
1
333583-202
IIKKGANP4301STMO01
1
1
92-0659
2
Label
for White-
USAGE
1. Turn off furnace
listed above.
See Table
2. Remove
gas and electrical
main furnace
3. Turn furnace
gas valve switch
1 for kit contents.
models, more parts
To accommodate
many different
furnace
are shipped in kit than will be needed to
4. Remove
burner
complete
parts.
When
5. Remove
gas supply
6. Remove
wires
conversion.
installation
is complete,
discard extra
INSTALLATION
DIRECT
VENT,
MULTIPOISE,
FURNACES
VARIABLE-SPEED,
1 --
Install
NOTE:
See Fig.
orientation.
Reorient
installed
Burner
Orifices
2 for component
location
in
component
arrangement
when
UPFLOW
furnace is
in other positions.
OPERATION
Label all wires
controls.
7. Remove
8. Remove
prior
reference
9. Remove
A96249
ELECTRICAL
could
Furnace
disconnection
pressure
for reas-
when
fitting.
manifold
servicing
(See Fig. 2).
to burner
and gas valve
kit rating
or
tube from gas valve burner
pressure-tap
and discard orifices
mine main burner
Orifice
to
orifices,
10. Refer to conversion
Failure to follow
this warning
injury, death or property damage.
location
may result in unit damage
screws that secure
move manifold,
sembly.
FIRE, EXPLOSION,
HAZARD
Note
HAZARD
burner-box
enclosure;
Fig. 1 - Burner
gas valve.
Failure to follow this caution
improper operation.
355CAV (Multipoise)
Main
pipe from gas valve.
from
CONDENSING
UNIT
Step
to OFF position.
front.
sembly.
SPEED MODELS
58MVC (Multipoise)
enclosure
4-WAY
STEP-MODULATING
VARIABLE
supplies.
door.
box and re-
train
as one as-
from manifold.
plate 333583-201
to deter-
orifice size. (See Fig. 3.)
gas input rate on furnace
rating plate is for installations
at
altitudes up to 2000 ft. In the U.S.A.; the input rating for altitudes
above 2000 ft. must be reduced by 2 percent for each 1000 ft.
above sea level.
SHOCK
result
in personal
Gas supply
MUST
be shut off before
disconnecting
electrical power and proceeding with conversion.
In Canada, the input rating must be derated
altitudes of 2000 ft. to 4500 ft. above sea level.
by 5 percent
The Conversion
derate.
for
11. Install
Kit
Rating
main burner
ger-tighten
threading,
Plate
orifices.
accounts
high
Do not use Teflon
for
altitude
tape. Fin-
orifices at least one full turn to prevent crossthen tighten with wrench. There are enough ori-
fices in each kit for largest furnace.
Discard
extra orifices.
BURNER
D'4CLOSURE
MANIFOLD
THROTTLING
VALVE
UNIT
DAMAGE
HAZARD
Failure
to follow this caution
DO NOT re-drill
burner
result in burrs, out-of-round
BURNERENCLOSURE
REFFERENCETUBE
may result in unit damage.
orifices. Improper
drilling may
holes, etc. Obtain new orifices
if orifice size must be changed.
(See Fig. 1.)
GAS VALVE
Step
2 -- Reposition
Remove
two
Air
screws
Shutter
holding
air shutter
in natural
gas usage
(NAT) position.
CONTORL
1. Reposition
air shutter to propane gas usage (PROP) position. (See Fig. 4). Screws will now be located in the shutter next to the PROP
NOTE:
Air
opening
obstructed
by air shutter.
stamp.
above
Step 3 -- Install Diverter
burners
now
be
partially
Plate
1. Install diverter plate (provided
air intake box as follows:
a. Remove
will
in kit) above
front two screws on combustion
combustion
air intake box.
AO6692
Fig. 2 - Multipoise
Variable
Speed
Component
Condensing
(See Fig. 5.)
Furnace
b. Remove
Location
combustion
air intake box and set aside.
c. Install diverter plate Part Number
NOTE:
DO
assembly,
and burner
NOT
reinstall
enclosure
the manifold,
orifices,
323184-301
provided
in kit. (See Fig. 6.)
gas-valve
d. Reinstall combustion
air intake box and replace two
screws to ensure diverter plate is properly installed. (See
front at this time.
Fig. 5.)
f
/
CONVERSION
KIT
RATING
PLATE
-
T_L_ APPUARCE
HAS B_EN CONVERTED TO USE PEOPARE GA_ FOR FUEL
CONVERt;lOB PROCEO_REE,
USE PART5 SUPPLIED
BY CARBIER CORPORATION
R;ED EXIR;TING EATING PLATE FOR; APPt3ANCE MODEL N0. AND iNPUT P,ATNG_
ALTITUDE
NOD_L8
0
2001
_0 2000
58MVC,
355CAM
Orifice
M_fld
No.
_
tO,3000
%25mm
!.25mm
1%0 /
1!.0
/
5.5
/
CORE
FOR
PERSONNEL,
F%L U_E0:PROPANEGAS N_T PRESSU,_
_ - ram::
I - 3_ _ _'_
OF INBTALLATION {FT, ABOVE
S_A LEVEL) U,B.A, *
KT fi0KG#_P_Z_I_
APPLIANC_
CARRIER
REFER TO KiT _MSTRUCT_N_
AND [NETALLBB BY _JALFIEB
3001
4001
5001
0001
7001
8001
_001
tO 4000
IO 5000
_o 6000
tO _OO0
tO 8000
I0 9000
_0 10000
!.25mm
1,25mm
1,25mm
1,25mm
1,25mm
1,25mm
1.25mm
#ross
High
M_
5.8
Low
2.2
/
2.!
!1.0
5.5
2_1
¢
11,0 /
/
5=5 _
11.0 i
5.4
2.1
2.1
/
11.0
/
11.0 f
/
110
5.4
/
B=4 _
5=3 /
5.3
2.0
2.0
2.13
2.0
ForCanadianinstalhtions from 2000to 4,500ft. useLI,R;
J',.column200"tte 3000ft,
11.0
/
:,'_33583,.20
t REVA
A07831
Fig. 3 - Conversion
Kit Rating
Plate
GAS
POSITION
PROP
o NAT
!
A96264
Fig. 4 - Air Shutter
in Propane
Gas
Usage
(PROP)
Position
A06693
Fig. 5 - Removing
Combustion
Air Intake
A06695
Box
Fig. 6 - Installing
Diverter
Plate
A06_6
Fig. 7 - Igniter
to Burner
Step 5 -- Replace
Gas Valve
Regulator
UNIT
DAMAGE
Failure
to follow this caution
Springs
and Pre-adjust
HAZARD
may result in unit damage
The gas valve must be pre-adjusted
before operating
on
propane gas.
If left non-modified,
sooting and corrosion
will occur leading to early heat exchanger failure.
1. Be sure gas and electrical
supplies
to furnace
are off.
2. Remove
caps that conceal
adjustment
screws for high-,
medium-,
and low-heat
stage gas-valve
regulators.
(See
Fig. 9.)
3. Remove the high-heat
ment screws.
and medium-heat
4. Remove
the high-heat
springs (silver).
5. Install
A06697
Fig. 8 - Position
Step
4 --
Install
1. Reinstall
burner
Manifold
to Burner
orifice,
Ensure
and
manifold
gas-valve
seal
grommet
properly
and burners fit over orifices.
Burner alignment.
See Fig. 7 and 8.
2. Reconnect
schematic
3. Reinstall
fitting.
NOTE:
wires to gas valve. Refer
for proper wire location.
burner
box pressure
DO NOT reinstall
burner
assembly
Verify
enclosure
is installed
Igniter
to furnace
tube to gas-valve
in
to
wiring
and medium-heat
and medium
adjust-
gas regulator
heat propane
gas regu-
lator springs (white).
6. Install the high-heat
ment screws.
Assembly
manifold,
box.
of Igniter
the high-heat
regulator
and medium-heat
regulator
adjust-
7. Turn high-heat
stage adjusting screw clockwise
(in) 13.5
full turns. This will increase the manifold pressure closer
to the propane
high-heat
8. Turn medium-heat
stage
9.5 full turns.
This will
closer to the propane
set point.
adjusting
increase
medium-heat
(See Fig. 9.)
screw clockwise
(in)
the manifold
pressure
set point.
(See Fig. 9.)
regulator
front at this time.
_8" brass male coupling
NIGH HEAT
ON/OFF
(UNDER CAP)
BURNER
ENCLOSURE
REFFERENCE
TAP
INLET
brass female x female x
male tee for installing
LGPS
PRESSURE
\
A05155
Fig. 10 - Gas Valve
Inlet
Pressure
tap
MEDIUM NEAT
ADJUSTMENT
(UNDERCAP)
LOW HEAT
ADJUSTMENT
(UNDERCAP)
/
...............
Manomete__
MANIFOLD
PRESSURE
TAP
A07280
Fig. 9 - Redundant
Automatic
Gas Valve
Valve
with Throttling
connection
_
_
A05191
Fig. 11 - LGPS
Installed
9. Turn low-heat
stage adjusting
screw (flat blade screwdriver screw) clockwise (in) the number of turns shown in
Table 2. This will increase the manifold pressure closer to
the propane
low-heat
set point.
10. Do not install regulator
(See Fig. 9.)
7. Connect
Step
7 --
NOTE:
between
seal caps at this time.
Table 2 - Low Stage Pie-Adjustment
Model
Number of Turns
042060 / 060-14
1%
042080 / 080-14
2 Vz
060080 / 080-20
2 _/z
060100 / 100-20
3
060120 / 120-20
3 _/_
a manometer
in the gas valve.
Check
to the open end of the tee installed
(See Fig. 11.)
Inlet
Gas
Pressure
This kit is to be used only when
11.0-in. wc and 13.6-in. wc.
1. Veri_, manometer
valve.
is connected
inlet gas pressure
to inlet pressure
tap on gas
UNIT
DAMAGE
Step 6 -- Install Low Gas Pressure Switch (LGPS)
Failure
to follow this caution
NOTE:
DO NOT operate furnace more than one minute to check
inlet gas pressure, as conversion is not complete at this time.
Use propane-gas
to prevent
gas leaks.
valve.
3. Apply
pipe dope on all connections
DO NOT use Teflon tape.
1. Be sure main
2. Remove
resistant
gas and electric
1/8-in.
pipe plug
supplies
to furnace
from inlet pressure
(See Fig. 9.) DO NOT DISCARD
pipe
dope
sparingly
of 1/8 in. brass
male coupling
(provided
in kit) and install it in 1/8 in.
tapped opening in gas valve inlet pressure-tap.
Tighten
fitting with a small wrench.
4. Attach
the female
end of the female x female x male brass
(See Fig. 10.)
propane
nipple.
wrench
pipe dope sparingly
control
6. Apply
to male end of brass tee. Install
low gas pressure
switch (provided
in kit) on
After switch has been finger tightened, use small
on base of pressure
switch for final tightening.
When pressure
point as shown
switch is tight, switch terminals
should
in Fig. 11 relative to gs valve and clear
compartment
pipe dope
2. Turn on furnace
power
3. Turn gas supply
manual
4. Turn furnace
5. Turn
Setup
6. Jumper
control.
supply.
shutoff
gas valve switch
Switch
SW4-2
valve to ON position.
to ON position.
on furnace
control
ON (see
to end of inlet gas pipe and
connect gas supply pipe to gas valve using backup wrench
on gas valve to prevent rotation and improper orientation.
R-W/W1
and R-W2
thermostat
connections
on
7. When main burners ignite, confirm inlet gas pressure
between 11.0-in. w.c. and 13.6-in. w.c.
8. Remove jumper across
connections
to terminate
9. Turn furnace
R-W/W1
and R-W2
call for heat.
gas valve switch
10. Turn gas supply
manual
11. Turn off furnace
power
12. Remove
access door.
sparingly
may result in unit damage.
Fig. 13)
(See Fig. 10.)
tee (provided
in kit). Tighten fitting with a small wrench
so the male portion of the tee points out from the furnace.
5. Apply
HAZARD
are off.
tap on gas
PLUG!
to the ends
is
is
thermostat
to OFF position.
shutoff
valve to OFF position.
supply.
manometer.
13. Apply pipe dope sparingly to end of inlet gas pipe plug
and install into unused end of 1/8 in. tee. Use a small
back-up
wrench
on
tee when
tightening
gas
inlet pipe
plug. (See Fig. 11)
BURNER ENCLOSURE
GAS VALVE
THROTTLING
VALVE
PRESSURE
SWITCHES
-2_4
MANOMETER
A06701
Fig. 12 - Checking
Line Pressure
USERINTERFACE
OR ADVANCEO
PRODUCT
MONFTO_
MODEL PLUG
_LOWER
O_
CONTINUOUSFAN
(OF)AI_LOW
SETUPSWITCHES
-
"
SW4 SETU_
SWITCHES
OAT
CONNECTOR
OAJ
DELAY
(A/C)
AIR
FlOW
SFUP SW_TCHES
_'
HUMIDIFIER
TEflM_NAL(2_VAC
0,5 AMPMA×,
CONDmONING
RELAYD_SABLE
JUMPE_
CONNECTOR
(FACTORY
ONLY)
\
PL3
ECMB_OWE_
HARNESS
N_ONNECTO_
NUMBER
\
115VAC (_2)NEUTRAL
CONNECTIONS
PEt LOWVOLTAGEMAFN
HARNESSCONNECTOR
_
VOLTA_
soFrwAfl_
VERSION
NUM_
PL2 HOTSURFACE
_GNITE__INOUCER
MOTORCONNECTOR
EXAMPLE:
pART
NUMBER
CONNECTIONS
DATE
COD_
A07422
Fig. 13 - Furnace
Step
8 --
Pressure
Switch
Wiring
(refer
from
low-heat
Control
4. Turn gas supply
to furnace
wiring diagram)
5. Turn furnace
1. Disconnect
orange wire
LPS on inducer housing.
2. Connect
uninsulated
pressure
terminal
of one
orange
wire
(pro-
3. Connect
insulated
terminal of second orange wire (provided in kit) to N.O. terminal on low gas pressure switch
LGPS. Connect other end to pressure switch LPS located
on inducer
housing.
orange
wires along wire harness.
with wire tie provided
Step
9 --
Check
Necessary
Furnace
secure
2. Remove
throttling
gas and electric
and
supplies
Make
to furnace
1/8-in.
pipe plug from manifold
valve.
(See Fig. 9.)
manometer
valve (See Fig. 14.)
to manifold
10 --
furnace
propane
pressure
pressure
tap on
tap on throttling
to ON position.
pipe connections
power
Input
valve to ON position.
Rate
rate for propane
for gas leaks.
supply.
Information
is the same as for natural
gas. See
rating plate (Fig. 16) for input rate. The input rate for
is determined
by manifold pressure and orifice size (See
Fig. 3.) The gas-valve
regulator must be set for high heat first,
then medium heat and then set for low heat.
NOTE:
Manifold
pressure
MUST
always
be measured
with the
burner enclosure front REMOVED.
(See Fig. 2.) Furnace gas
input rate on rating plate is for installations at altitudes up to 2000
ft.
reduced
are off.
Gas
The gas-input
In the U.S.A..
Operation
Adjustments
1. Be sure main
3. Attach
If possible,
in kit.
Step
shutoff
gas valve switch
all threaded
7. Turn on furnace
vided in kit) to splice connector.
Connect other end to C
terminal on low gas pressure switch LGPS.
Connect the
other end of the splice connector to the orange wire disconnected
in Step 1.
4. Route
6. Check
switch
manual
the input rating for altitudes
by 2 percent
above
for each 1000 ft. above
2000 ft. must be
sea level.
In Canada, the input rating must be derated by 5 percent
altitudes of 2000 ft. to 4500 ft. above sea level.
The Conversion
derate.
Step 11 --
Kit
Rating
Set Gas Input
Plate
Rate
accounts
for
high
for
altitude
BURNER ENCLOSURE
(REMOVE COVBR WHEN
CHECKING PRESSURE}
THROTTLING
VALVE
GAS VALVE
MANOMETER
AD06702
Fig. 14 - Adjusting
1. Setup
switch
SW4-2
on control
in the ON position.
ON position.
medium-heat
2. Jumper
on furnace control.
locked in high-heat
3. Turn high-heat
(out)
to decrease
(in) to increase
jumper
7. Wait for blower
to furnace.
locked
in
connections
keeps
hex Allen wrench)
manifold
pressure
or
pressure.
then turn medium-heat
wrench)
adjusting
screw
(out)
to de-
counterclockwise
or
clockwise
(in) to increase
off-delay
9. Jumper R to W/W1
start furnace.
10. Wait for the blower
power
to OFF position.
thermostat
connections
on control
to turn ON then check low-heat
to
mani-
fold pressure. Remove the low-heat
adjustment
cap (See
Fig. 9) and turn the low-heat
adjusting screw clockwise
(in) to decrease
manifold
pressure
or counterclockwise
(out) to increase manifold pressure. You will only have 15
minutes to make and adjustment.
If you need more time
then move
position
11. When
setup
switch
(SW1-2
on control
center to ON
(See Fig. 13.)
correct
manifold
pressures
are
caps that conceal
gas valve adjustment
er flame should
Fig. 15.)
be clear
blue.
almost
obtained,
screws.
replace
Min burn-
transparent.
12. Remove jumper across R to W/W1.
If necessary
setup switch SW1-2 to the OFF position.
14. Turn off furnace
(See
power
supply.
switch
or control
move
knob
to
and
reattach
gas valve switch
power
19. Set room thermostat
manifold
pressure
tap
to ON position.
supply.
to call for heat.
20. Check
ignite.
pressure
21. Check
for correct burner
tap plug for gas leaks when main
burners
flame.
22. Observe unit operation through 2 complete heating cycles.
See Sequence
of Operation
in furnace Supplemental
Instructions.
23. Set room thermostat
--
Check
installed
to desired
Low
Gas
temperature.
Pressure
low gas pressure
Operation
Switch
switch
is a safety
device
used to guard against adverse burner operating characteristics
that
can result from low gas supply pressure. Switch opens at not less
than 6.5 in. w.c. and closes at not greater than 10.2 in. w.c.
This switch also prevents
is low which can result
operation
when the propane tank level
in gas with a high concentration
of
impurities, additives, and residues that have settled to the bottom
of the tank. Operation under these conditions
can cause harm to
the heat exchanger
This normally
system.
open
switch
closes
valve under
normal
operating
completes control circuit. Should
when
gas is supplied
pressure.
The
an interruption
to gas
closed
switch
or reduction
in
gas supply occur, the gas pressure at switch drops below low gas
pressure switch setting, and switch opens.
Any interruption
in
control circuit (in which low gas pressure switch is wired)
closes gas valve and stops gas flow to burners.
When
normal
electrically
13. Turn furnace gas valve control
OFF position.
manometer
plug to the throttling valve. (See Fig. 9.)
16. Reinstall burner enclosure front.
The newly
to finish then reset 115-v
SW4-2
Attachment)
15. Remove
Step 12
across R to W/W1.
8. Move setup switch
(Manifold
18. Turn on furnace
furnace
across R to W/W2.
hex Allen
jumper
be
in the
Pressure
17. Turn furnace
This
(3/32
manifold
crease manifold
pressure
manifnld pressure.
6. Remove
13.)
screw
5. Wait one minute
(3/32)
(See Fig.
operation.
already
furnace
and R to W2 thermostat
adjusting
counterclockwise
4. Remove
should
switch SW4-2
(See Fig. 13.) This keeps
operation.
R and W/W1
clockwise
center
If not, put setup
Manifold
Before
gas
pressure
reset to re-establish
leaving
installation,
is restored,
normal
observe
the
heating
unit
system
quickly
must
be
through
2
operation.
operation
complete heating cycles. During this time, turn gas supply to gas
valve off just long enough to completely
extinguish burner flame.
then instantly restore full gas supply. To ensure proper low gas
pressure switch operation,
observe that there is no gas supply
burners until after hot surface igniter begins glowing.
to
GASCONTROL
LABEL
BURNER
RATING
PLATE
FLAME
BURNER
ENCLOSURE
BURNER
LABEL
- GASVALVE
CONTROL
FURNACECONVERSION
RATINGPLATE
MANIFOLD
A89020
Fig. 15 - Burner
Step
13 --
Label
Flame
Application
1. Fill in Conversion
Responsibility
Label
333583-203
and
apply to Blower Access Door of furnace as shown. (See
Fig. 16.) Date. name. and address of organization
making
this conversion
are required.
2. Attach Conversion
Rating Plate
Fig. 16 to Outer Door of furnace.
3. Apply Gas Control Conversion
label 333583-203
to gas valve.
4. Reinstall
main furnace
door.
Label
A01025
Fig. 16 - Condensing
333583-201,
Label to gas valve:
see
Apply
Furnace
Label
Location
Copyright
Manufacturer
2007
CAC
rese_'es
BDP
the
• 73t0
tight
W
Molds
to change,
St • Indianapolis,
at
any
time.
IN
specifications
46231
and
Pdi_ted
designs
without
notice
and
in USA
without
Catalo_
obllgatlolls.
10
No: IIKKGANP4301STM001
Rep_aoes:
New
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.2 Linearized : No Page Count : 10 Page Layout : SinglePage Page Mode : UseNone Producer : Goby Monitor Application version 4, 0, 0, 13 Create Date : Tue Mar 25 06:20:56 2008 Author : Title : Subject :EXIF Metadata provided by EXIF.tools