Users Manual
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 1691071 |
| Application ID | QR04GyLADDfAMnwRaIVOug== |
| Document Description | Users Manual |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 336.33kB (4204087 bits) |
| Date Submitted | 2012-05-07 00:00:00 |
| Date Available | 2012-05-07 00:00:00 |
| Creation Date | 2011-09-09 10:41:56 |
| Producing Software | pdfFactory Pro 3.17 (Windows XP Professional Chinese) |
| Document Lastmod | 2012-04-19 17:51:12 |
| Document Title | E103-IP user manual-v1.0.doc |
| Document Creator | pdfFactory Pro www.fineprint.cn |
| Document Author: | Administrator |
E103IP USER MANUAL VERSION: V1.0 FOR MODELS: E103IP, E203IP CONTENTS 1. INTRODUCTION ..........................................................................................5 1.1 OVERVIEW OF HARDWARE ..................................................................................................... 5 1.2 OVERVIEW OF SOFTWARE ...................................................................................................... 5 2. E103 IP PHONE KEYBOARD..................................................................7 2.1 KEYBOARDS FUNCTIONS ........................................................................................................ 7 2.1.1 Function Table of Base Keyboard ......................................................................... 7 2.1.2 Function table of handset keyboard.................................................................... 7 2.2 KEYBOARD FUNCTION ............................................................................................................ 7 2.2.2 Voice Control .............................................................................................................. 8 2.2.3 Hold Function............................................................................................................. 8 2.2.4 Register handset ....................................................................................................... 8 2.2.5 Delete handset .......................................................................................................... 9 2.2.6 Call forward ................................................................................................................ 9 2.2.7 Three way conference call ..................................................................................... 9 2.2.8 Line Switch ............................................................................................................... 10 2.2.9 Call park function ................................................................................................... 10 2.3 FUNCTIONS AND SETTING CATALOG .................................................................................... 10 2.3.1 Menu catalog............................................................................................................ 10 2.3.2 Network ..................................................................................................................... 10 2.3.3 Call Feature .............................................................................................................. 11 2.3.4 SIP .............................................................................................................................. 11 2.3.5 DSP ............................................................................................................................. 12 2.3.6 System ....................................................................................................................... 12 2.3.7 Other Setting ........................................................................................................... 12 2.3.8 Setting catalog ........................................................................................................ 12 3. THROUGH WEB BROWSER TO SET PHONE ..................................13 3.1 LOGON.................................................................................................................................. 13 3.2 CURRENT STATE ................................................................................................................... 13 3.3 NETWORK ............................................................................................................................. 14 3.3.1 Wan Config ............................................................................................................... 14 3.3.2 LAN Config................................................................................................................ 15 3.4 VOIP .................................................................................................................................... 16 3.4.1 SIP Config ................................................................................................................. 16 3.5 ADVANCE .............................................................................................................................. 19 3.5.1 DHCP Server ............................................................................................................ 19 3.5.2 NAT ............................................................................................................................. 20 3.5.3 STUN .......................................................................................................................... 21 3.5.4 Net Service ............................................................................................................... 21 3.5.5 Firewall settings ...................................................................................................... 22 3.5.6 VLAN Configuration ................................................................................................ 23 3.5.7 Digital Map................................................................................................................ 24 3.5.8 Call Service Settings.............................................................................................. 25 3.5.9 Memory Key ............................................................................................................. 26 3.5.10 MMI Filter................................................................................................................ 26 3.5.11 DSP........................................................................................................................... 27 3.5.12 VPN........................................................................................................................... 27 3.6 DIAL-P EER DIAL RULE SETTING ........................................................................................... 28 3.7 CONFIG MANAGE ................................................................................................................. 29 3.8 UPDATE FIRMWARE .............................................................................................................. 30 3.8.1 Update ....................................................................................................................... 30 3.8.2 Auto Update ............................................................................................................. 31 3.9 SYSTEM MANAGE ................................................................................................................. 32 3.9.1 Account Manage...................................................................................................... 32 3.9.2 Syslog config............................................................................................................ 32 3.9.3 Phone Book............................................................................................................... 33 3.9.4 Time Set .................................................................................................................... 33 3.9.5 MMI SET .................................................................................................................... 34 3.9.6 Logout & Reboot ..................................................................................................... 34 4. OPERATING METHOD FOR DIALING...............................................35 4.1 HOW TO DIAL IP P HONE ...................................................................................................... 35 4.2 SET THE PHONE BEING CONNECTED TO SERVER .................................................................. 35 4.2.1 Set the WAN interface........................................................................................... 35 4.2.2 SIP setting： ............................................................................................................ 36 4.3 HOW TO USE THE DIAL RULE ?.............................................................................................. 37 4.4 VOICE MAIL .......................................................................................................................... 38 After phone is boot-up and obtains the TFTP Server address through DHCP Sever, then phone will produce “toot-toot” sound to prompt entering “Config ID”. After inputting ID through the numeric keyboard and “#” for ending, phone will auto-download the config file from TFTP Server. If the download is successful, phone will be re-boot; if failed, 15s later phone will enter into default standby status; if you do not want to download, you can press "#" directly for entering into the default standby status; if the download is not completed or the downloaded config file “autoupdate module” has no config parameter in the “config file name”, phone will still prompt inputting “Config ID” after re-boot. After phone enters into the default standby status, pressing “**47”key will make the phone auto-broadcast its own IP address. Function 1. Provide a Backup SIP Server 2. Support NAT, Firewall 3. Support DHCP assigning IP address, etc automatically 4. Support PPPoE (used while connecting ADSL，cable modem) 5. It can update the program through HTTP, FTP and TFTP 6. Check the dynamic voice; Soft the noise; Buffer technique of voice 7. Hold Function 8. Hotline Function 9. Speed-dial 10. Call-forward, Three-way conference call 11. DND (Do Not Disturb), Black List, Limit List 12. Auto-answer. 13. Set through standard Web Browser 14. Remote Management Function 15. Classification management for common user’s password and super user’s password. 16. Broadcast the IP address, Vlan ID, version number and phone number. 17. Cordless Handset, 1.9GHz Operation, with Handshake Technology 18. Support VLAN function 19. Call park function Standard and Protocols ◆ IEEE 802.3 /802.3 u 10 Base T / 100Base TX ◆ PPPoE ◆ DHCP Client and Server ◆ Support G.711a/u, G729, G7231 5.3/6.3 audio Codec ◆ SIP RFC3261, RFC 2543 ◆ Support IAX2 ◆ TCP/IP: Internet transfer and control protocol ◆ RTP: Real-time Transport Protocol ◆ RTCP: Real-time Control Protocol ◆ VAD/CNG save bandwidth ◆ Telnet: Internet's remote login protocol ◆ DNS: Domain Name Server ◆ TFTP: Trivial File Transfer Protocol 1. Introduction This is the user manual of E103 IP . Some configuration should be done before use the E103 IP phone, and then it can work normally. This manual will illustrate how to set the phone through keyboard and web service. 1.1 Overview of Hardware 1.1.1 The two RJ-45 network interface support the 10/100M Ethernet. The default WAN interface is a DHCP Client server. Users connect the WAN interface to ADSL or switch, and connect the LAN interface to the computer. You can use the administrator’s user name “admin” and password “admin” to login and set. 1.1.2 Only the WAN interface supports the POE. 1.2 Overview of Software Network Protocol Tone SIP v1(RFC2543) Ring Tone v2(RFC3261) Ring Back Tone IP/TCP/UDP/RTP/RTCP Dial Tone IP/ICMP/ARP/RARP/SNTP Busy Tone TFTP Client/DHCP Client/PPPOE Telnet/HTTP Server Phone Function DNS Clients Volume Adjustment Speed dial key Phonebook Client Codec G.711： 64K bit/s(PCM) G.723.1： 63k/5.3k bit/s G.726： 16k/24k/32k/40k IP Assignment bit/s(ADPCM) IP (Static IP) G.729A： 8k bit/s(CS-ACELP) DHCP G.729B： adds VAD & CNG to G.729 PPPoE Voice Quality VAD： Voice activity detection CNG： Comfortable noise generator LEC： Line echo canceller Packet Loss Compensation Adaptive Jitter Buffer Security HTTP 1.1 basic/digest MD5 for SIP authentication authentication for Web setup (RFC2069/RFC2617) QoS Call Function QoS field NAT Traversal Call Hold STUN Configuration Call Waiting Call Forward Web Browser Caller ID Console/Telnet 3-way conference Keypad DTMF Firmware Upgrade DTMF RELAY TFTP DTMF RFC 2833 HTTP DTMF SIP Info FTP SIP Server Provide a Backup SIP Server 2. E103-IP phone keyboard 2.1 Keyboards functions 2.1.1 Function Table of Base Keyboard Name Status Store On-hook To enter storage mode for speed dialing Flash On-hook To enter the deleting mode for pressing down 3 seconds Redial Dialing On-hook Function Re-dial the last called number It’s calling handset for press down for a little time and registering with handset for pressing down 3 seconds Locate Call calling the handset Volume + Call Increase the volume Volume - Call Decrease the volume Speak Mute M1~M7 Voicemail Hands free Call On-hook Dialing On-hook Dialing Mute 7 speed dial numbers Pick up voicemail Dialing “1” Dialing “2” Dialing “3” Dialing “4” Dialing “5” Dialing “6” Dialing “7” Dialing “8” Dialing “9” Dialing “0” Dialing “*” Dialing It can be regarded as the first number being dialed out or the end mark for ending number. 2.1.2 Function table of handset keyboard 2.2 Keyboard Function Item Status Line1 On-hook ON/OFF Talking Line2 On-hook ON/OFF Talking Function On/off Hook switch of Handset Hold/retrieve the current line talking On/off Hook switch of Handset Hold/retrieve the current line talking Hold Call Call Waiting Mute Call Mute Redial Dialing Volume + Call Increase the volume Volume - Call Reduce the volume FNC Off-Hook Dialing On-Hook Redial the number of last time Quickly cut off the current line and off-hook again. “1” Long pressing can pick up the message Dialing “2” Dialing “3” Dialing “4” Dialing “5” Dialing “6” Dialing “7” Dialing “8” Dialing “9” Dialing “0” Dialing “*” On-Hook Dialing Long pressing for seconds entering into the registration status of the handset It can be regarded as the first number being dialed out or the end mark for ending number. 2.2.1 Store numbers Press “STORE” key to enter into the setting state of storing keys, and input storing number, then press the corresponding storing key to store the numbers. 2.2.2 Voice Control Pressing “VOL+” to increase the volume, and press “VOL-” to decrease the volume. 2.2.3 Hold Function It is used for holding the current line or forwarding to other handset, for example: When you use the #1 handset and want to use the #2 in a call, now you need to hold the #1 handset then pick up the #2 handset. If line1/2 is in the conversation, press down “line1/2” key or “hold” key, may hold the current conversation. 2.2.4 Register handset The handset registers to the base have two ways: Manual registration and automatic registration. Manual registration: Under On-Hook status, pressing the “Locate” key on the base unit for three seconds to enable the handset register mode, and the Charge indicator light flashes at the same time; then press “*”key for three seconds to enable the handset register mode, then ON/OFF indicator light on the handset, and will give the prompt tone for successful registration. Automatic registration: place the handset in the plane, the “charge” instruction light begins flash at the same time, it means enable the handset register mode, the “ON/OFF” instruction light flashes at the same time, if the handset register to the base is successful, then the “charge” instruction light on the base and the “ON/OFF” instruction light on the handset will stop flickering, and will give the prompt tone for successful registration. Note: Each base phone can most register 5 handsets. 2.2.5 Delete handset Keep pressing the “FLASH” key on the base unit for three seconds, the Speaker will give “beep” sound, then Press “0” on the base unit to delete all the handset. Press “1” on the base unit to delete the first handset. Press “2” on the base unit to delete the second handset. Press “3” on the base unit to delete the third handset. Press “4” on the base unit to delete the fourth handset. Press “5” on the base unit to delete the fifth handset. After pressed the number keys, Charge indicator light will flashes, which means the handset is being deleted by the phone. When Charge indicator light stops flashing, it means that the deletion is finished. 2.2.6 Call forward Choosing the “forward type” of the “Advanced Sip Setting” (the default option is “OFF”). Choose one of the three types which contain always, busy and no answer to realize call forward. 2.2.7 Three way conference call 2.2.7.1 Three way conference call of the handset 1) Choosing the “Enable Three Way Call” of “Call Service Setting” (the default option status of the phone), suppose the user of the E103 IP phone is A, and if user B calls user A through VoIP phone, user B needs to make 3-way conference call with user A and C, then user A can use the second line to call user C, the call auto-maintain with user B, during the conversation with C, pressing down “*”, then can make 3-way conference call. 2) Choosing the “Enable Three Way Call” of “Call Service Setting” (the default option status of the phone), suppose the user of the E103 IP phone is A, and if user B calls user A through VoIP phone, user B needs to make 3-way conference call with user A and C, then user A can use the second line to call user C, the call auto-maintain with user B, during the conversation with C, pressing down “Conf”, then can make 3-way conference call. 2.2.7.2 Three way conference call of the base unit Choosing the “Enable Three Way Call” of “Call Service Setting” (the default option status of the phone), suppose the user of the E103 IP phone is A, and if user B calls user A through VoIP phone , user B needs to make 3-way conference call with user A and C, then user A can use the second line to call user C, the call auto-maintain with user B, during the conversation with C, pressing down “*” can make 3-way conference call. 2.2.8 Line Switch 2.2.81 Handset Line Switch 1）Suppose the line1/2 of handset is talking, the line2/1 is holding, if you want to implement line switch, first you need to press down “Hold ”, then press down “ON/OFF” of the choice line. You can implement line switch. 2) Suppose the line1/2 of handset is holding, the line2/1 is dialing, if you want to switch to line1/2 talking, first hang up line2/1, then press down “ON/OFF” of Line1/2 or press “HOLD”. You can implement line switch. 2.2.8.2 Base unit Line Switch Suppose the line1/2 of the base unit is talking, line2/1 is holding, press down “line2/1” directly and switch to line2/1 talking. 2.2.9 Call park function The “Park1” in the “Park Mode” of “Advanced SIP Setting” should be in chosen mode(the default one is chosen default mode), config the related parameter “s”, “t” and “p” in memory key page, call park function may use normally afterward. 2.3 Functions and setting catalog 2.3.1 Menu catalog 1) Network 2) Call Feature 3) SIP 4) DSP 5) System 6) Other Setting 2.3.2 Network 2.3.2.1 LAN 1) Bridge Mode 2) IP 3) Netmask 4) DHCP Server ◆Switch ◆DNS Relay 5) NAT ◆Switch ◆FTPalg ◆PPPTPalg 2.3.2.2 WAN 1) Status 2) Static Net ◆IP ◆NetMask ◆Gateway ◆DNS ◆DNS2 10 3) PPPOE ◆User name ◆Password 4) QoS 2.3.3 Call Feature 23.3.1 Phone-number 1) Public SIP 2) Private SIP 2.3.3.2 Limit-List 1) Current 2) ADD 3) DEL 2.3.3.3 Black-List 1) Current 2) ADD 3) DEL 2.3.3.4 FastCall 2.3.3.5 Three Talk 2.3.3.6 Call-Waiting 2.3.3.7 Call-Forward 1) Condition 2) SIP ◆Transfer Num ◆Transfer IP ◆Port 2.3.3.8 Dial-Rule 1) End with “#” 2) Fixed Length ◆Switch ◆Length 2.3.4 SIP 2.3.4.1 Reg Status 1) Public Reg 2) Private Reg 2.3.4.1 Reg Switch 1) Public 2) Private 2.3.4.2 Server 1) Public 2) Private 2.3.4.3 Domain 1) Public 2) Private 2.3.4.4 User Agent 11 1) Public 2) Private 2.3.4.5 Detect-server 2.3.4.6 Dtmf-mode 2.3.4.7 Interval-time 2.3.4.8 Swap-server 2.3.4.9 RFC-version 2.3.4.10 Signal-Port 2.3.4.11 Stun 1) Switch 2) Addr 3) Port 4) Expire Time 2.3.5 DSP 2.3.5.1 Codec 2.3.5.2 Handdown-time 2.3.5.3 Dtfm-Volume 2.3.5.4 Input-Volume 2.3.5.5 Output-Volume 2.3.6 System 2.3.6.1 Save 2.3.6.2 Reboot 2.3.6.3 Set Default 2.3.7 Other Setting 2.3.7.1 Syslog 1) Switch 2) Server-IP 3) Server-Port 2.3.8 Setting catalog 1. Pressing down the “Menu” key to enter the setting status of speed dial key and input the needed saving No., then press the corresponding speed dial key to save. 2. Pressing down “Menu” above 3 seconds to enter the setting status and the default keyword is 123, and then you can press “Enter” to enter, “Menu” to exit. 3. When modifying the setting, press “Redial” to enter modification status, and “0” is to make no choice, “1” is to make choice, “Enter” is to confirm the modification, and “Menu” is to quit the modification. After finished the modification setting, we will save it on “Save” menu. After rebooting all the settings will be go into effect. 12 3. through web browser to set phone Plug one end of the network line to the network card port of the computer, the other end to Lan port of the phone, phone will obtain the IP address automatically, open IE, input the IP address on Address column, then enter into the Web Setting Page. The method of obtaining the dynamic IP address is: Under the on-hook status, press “**47#”, then phone will broadcast the current IP address. 3.1 Logon The default user name and password are admin/admin and guest/guest. and， admin/admin is super user name and password，guest/guest is common user name and password。Logon interface is as follows： 3.2 Current state This page layout shows the work state of VoIP phone. The network part shows the connection state of WAN interface and LAN interface and the network setting; the work state of Public SIP service of VoIP part, and here you can see the registration and whether registered to the server or not. The Phone Number part shows the telephone numbers in Private SIP server and Public SIP server. 13 3.3 Network 3.3.1 Wan Config WAN port network setting page. Support static IP, dynamic obtain IP and PPPoE. Net Traffic Timeout: when wan port network emergence failure, the phone cannot obtain IP address; the phone will auto reboot after the setting time. The default time is 2mins. 802.1x Setting: when you enable the 802.1x, after the authentication completes successfully, it should then get IP using DHCP. Username: 802.1x server username is voip. Password: the default password is 123456. Enable 802.1x: enable 802.1x authentication. Configure Static IP: ----Enable Static; 14 ----Set E103-IP’s IP address in the IP Address; ----Set netmask in the Netmask field; ----Set router IP address in the Gateway; ----DNS Domain: ----Set local DNS server in the Preferred DNS and the Alternate DNS。 Configure to dynamic obtain IP ----Enable DHCP; If there is DHCP server in your local network, E103 IP will automatically obtain WAN port network information from your DHCP server. Configure PPPoE: ----Enable PPPoE ----PPPoE server: Enter “ANY” if no specified from your ITSP. ----Enter PPPoE username and password in the username and password. E103 IP will automatically obtain WAN port network information from your ITSP if PPPoE setting and the setup are correct. Notice: If user accesses the IP phone through WAN port. She/he should use the new IP address to access the IP phone when the WAN port address was changed. 3.3.2 LAN Config LAN IP /Netmask: Set the IP and Netmask for the LAN DHCP Server: Enable DHCP service in LAN port; after user changed LAN IP, phone will automatically modify DHCP Lease Table and save the configure according to IP and Netmask, DHCP server configure won’t take effect unless you reboot the device. NAT: Enable NAT. Bridge Mode: Enable this option to switch to bridge mode. IP phone won’t assign IP for its LAN port in bridge mode and its LAN and WAN port will be in the same network. (This setting won’t take effect unless you save the config and reboot the device) 15 3.4 VoIP 3.4.1 SIP Config Setting page of public SIP server: Register Server Addr: Register address of public SIP server; Register Server Port: Register port of public SIP server，default port is 5060; Register Username: Username of your SIP account (Always the same as the phone number); Register Password: Password of your SIP account. Proxy Server Addr: IP address of proxy SIP server (SIP provider always use the same IP for register server and proxy server, in this case you don’t need to configure the proxy server information.); Proxy Server Port: Signal port of SIP proxy; 16 Proxy Username: proxy server username; Proxy Password: proxy server password; Domain Realm: SIP domain, enter the SIP domain if any, otherwise E103-IP will use the proxy server address as SIP domain. Local SIP port: Local SIP register port, default 5060; Phone Number: Phone number of your SIP account; Enable Register: Enable/Disable SIP register.E103 IP won’t send register info to SIP server if disable register. Message Waiting Indication：Set Disable/Enable message waiting through pull-down menu, including: Disable：MWI is disabled, even if received NOTIFY message from the server indicating new voicemail, phone will not prompt.； Enable (Subscribe): MWI is enabled and SUBSCRIBE will be sent, if the server sends NOTIFY message indicating new voicemail received, MWI LED will blink to prompt. Enable(No Subscribe)：MWI is enabled, but phone will not send SUBSCRIBE, if the server sends NOTIFY message indicating new voicemail received, MWI LED will also blink to prompt. SIP1 Subscribe will still be used in config file: config option “0” means “Disable”, “1” means “Enable (Subscribe)”, “2” means “Enable (No Subscribe)”. Advanced SIP Setting Register Expire Time: Register Expire time, default is 60 seconds. E103-IP will auto configure this expire time as the server recommends if it is different from the SIP server. NAT Keep Alive Interval：NAT keep alive interval time, the default is 60 seconds; Forward Type: the type of call forward; (the default is OFF); OFF: Disable call forward; Busy: If the phone is busy, it will forward to the appointed phone; 17 No answer：If no answer, it will forward to the appointed phone; Always：The caller always forward to the appointed phone. Forward Photo Number：Call the forwarded phone number. Signal Key：Setting Signal Key; In order to prevent blocking, cooperate platform to encrypt signal, input key here, Media Key: Setting Media Key; Subscribe Expire Time: Config the time of sending subscription message; Each interval time, sending a subscription message. Mainly subscribe other’s state or voice message. Enable URI Convert：Enable URI Convert function, Exchange ‘#’to ‘%23’and sending out. Enable Keep Authentication: Whether allow the phone support register with authentication directly to send or not, Such device do not certification requirement and response with server every time, After the server received a request with the registration of certification, The server can directly reply confirmation message. Detect Interval Time：Set server detect interval time，if phone open SIP detect server function，it will detect server every time whether or not to respond. Signal Encode: Open signal encrypt; Rtp Encode: Open voice encrypt; Enable Via rport: Whether support the RFC3581 or not. Enable Via rport is used in inside network, and needs SIP server support. To maintain network equipment with net device outside of NAT connection. Enable Session Timer: Whether the phone support the RFC4028 or not .At a certain period of time to refresh conversation ,in case a long time ,the other side drop off or break off, after refresh ,the other side did not respond ,we will hang up. Enable PRACK:Whether the phone support SIP-prack function (used mainly in the CRBT). When you receive 183 signal, you can send prack message. Recommend to use the default configration. Answer With Single Codec: When called to do, Only in response to Codec. Long Contact: Config Contact field bring more parameter. Auto TCP: When th message body exceeds 1300 bytes, automatic transmission using the TCP protocol, to protect the availability of transmission. Detect Interval Time: Co-work with the Auto Detect Server, if Auto Detect Server is enable, E103 IP will periodically detect whether the SIP server is available according this setting. Encrypt Key: The particular service system decrypts of the key, matching with the server Type usage, the key provide by the particular service system supplier, default is empty Server Type：The particular service system supplier carries out the sign and speeches to encrypt, default is common； DTMF Mode: DTMF signal sending mode: support RFC2833, DTMF_RELAY (inband audio) and SIP info. RFC Protocol Edition: Current E103 IP SIP version. Set to RFC 2543 if the gate need to communicate to devices (such as CISCO5300) using the SIP 1.0. 18 Default is RFC 3261. Park Mode: the default park mode is default; it means that the phone disenables call park function. If you want to enable call park function, choose”park1” mode, click “APPLY” button。 3.5 Advance 3.5.1 DHCP Server DHCP server manage page. User may trace and modify DHCP server information in this page. DHCP Lease Table：display the IP－MAC corresponding table that the server distributed. Lease Table Name: Lease table name. Start IP: Start IP of lease table. End IP: End IP of lease table. Network device connecting to the E103 IP LAN port can dynamic obtain the IP in the range between start IP and end IP. Lease Time: DHCP server lease time. Netmask: Netmask of lease table. Gateway: Default gateway of lease table DNS: Default DNS server of lease table. DNS Relay: Enable DNS relay function. User may use below setting to add a new lease table. 19 Notice: This setting won’t take effect unless you save the config and reboot the device 3.5.2 NAT Advance NAT setting. Maximum 10 items for TCP and UDP port mapping. IPSec ALG: Enable/Disable IPSec ALG; FTP ALG: Enable/Disable FTP ALG; PPTP ALG: Enable/Disable PPTP ALG; Transfer Type: Transfer type using port mapping. Inside IP: LAN device IP for port mapping. Inside Port: LAN device port for port mapping. Outside Port: WAN port for port mapping. Click Add to add new port mapping item and Delete to delete current port mapping item. DMZ Config： 20 3.5.3 STUN This page is used to set the private sip server, stun server, and back up sip server information. STUN Server setting: SIP STUN is used to realize SIP penetrates through NAT, when the phone configures IP and port of STUN server (default is 3478) and select Enable SIP Stun, common SIP server can be used to realize the phone to penetrate through NAT. In this way, If you have common SIP proxy and STUN server parked public network, it is all right, but STUN only support three NAT ways: FULL CONE, restricted, port restricted; STUN Server Addr: configure stun server address; STUN Server Port: configure stun server port default 3478 STUN Effect Time: stun detect NAT type circle, unit: minute. Local SIP Port：SIP port of this phone. Load：Load the choices of SIP line. Use Stun：Stun. Set the Stun that allows/forbids use user setting. 3.5.4 Net Service HTTP Port: configure HTTP transfer port; default is 80. User may change this 21 port to enhance system’s security. When this port is changed, please use http://xxx.xxx.xxx.xxx:xxxx/ to reconnect. Telnet Port: configure telnet transfer port, default is 23. RTP Initial Port: RTP initial port. RTP Port Quantity: Maximum RTP port quantity, default is 200 Notice: Settings in this page won’t take effect unless save and reboot the device. If you need to change telnet port or HTTP port, please use the port greater than 1024, because ports under 1024 is system remain ports. HTTP service firbids if HTTP is set to 0. 3.5.5 Firewall settings Firewall setting page. User may set up firewall to prevent unauthorized Internet users from accessing private networks connected to the Internet (input rule), or prevent unauthorized private network devices to access the internet. Access list support two type limits: Input access limit or output access limit. Each type supports 10 items maximum. E103 IP firewall filter is base WAN port. So the source address or input destination address should be WAN port IP address. Configuration: In_access enable ：enable in_access rule； Out_access enable：enable out_access rule； 22 Input/Output: Specify current adding rule is input rule or output rule. Deny/Permit: Specify current adding rule is deny rule or permit rule. Protocol Type: Protocol using in this rule: TCP/IP/ICMP/UDP. Port Range: Port range of this rule. Src Addr: Source address. It can be a specific IP address or network address. Dest Addr: Destination address. It can be a specific IP address or network address. Src Mask: Source address mask. Indicate the source is dedicate IP if set to 255.255.255.255. Otherwise is network ID. Des Mask: Destination address mask. Indicate the source is dedicate IP if set to 255.255.255.255. Otherwise is network ID. 3.5.6 VLAN Configuration Below is QoS Configuration page: E103-IP phone implement QoS based on 802.1p, The QoS is used to mark the network communication priority in the data link/MAC sub-layer. E103-IP will sort the packets using the QoS and sends it to the destination. VLAN Enable: Enable VLAN election, it can separate the voice message, signaling message and data message at the second floor, and by configuring the IP precedence which in ToS field of voice message to realize the separation of voice message and data message at the third floor, through which to allow the upper switch or router to forward the voice message firstly. (On condition that the switch or router can identify the ToS field). VLAN ID: Dispose VLAN ID is added a Tag header after realize enable the VLAN function. The realized voice packets transfer at the same VLAN. The prerequisite is it must the same as VLAN of upper switch. The value range are 1~4094. DiffServ Enable: If enable the VLAN service, it indicates use DSCP mode to realize three layers QoS. This moment, the DSCP of SIP signals which between E103-IP Phone and MGC. It will use Class Selector 5 (The value is 0xA0). And the DSCP of mediums information (In RTP packets) would be used the values of DiffServ Value field. DiffServ Value: The value range： 23 0x28,0x30,0x38,0x48,0x50,0x58,0x68,0x70,0x78,0x88,0x90,0x98,0xb8.defa ult is 0xb8 ,oxb8 stands for best fast transmission; 28-38 is guarantee for the transmission priority for the 1st rank , 48-58 is guarantee for the transmission priority for the 2nd rank, 68-78 is guarantee for the transmission priority for the 3rd rank, 88-98 is guarantee for the transmission priority for the 4th rank. 802.1P Priority: The priority of 802.1p 3.5.7 Digital Map Digit map is a set of rules to determine when the user has finished dialing. E103 IP support below digital map: Digital Map is based on some rules to judge when user end their dialing and send the number to the server. E103 IP support following digital map: ----End With “#”：Use # as the end of dialing. ----Fixed Length:：When the length of the dialing is matched, the call will be sent. ----Timeout:：Specify the timeout of the last dial digit. The call will be sent after timeout ----Prefix:：User define digital map: [ ]：Represents the range of digit, can be a range such as [1-4], or use comma such as [1, 3, 5], or use a list such as [234] x ：Represents any one digit between 0~9 Tn：Represents the last digit timeout. n represents the time from 0~9 second, it is necessary. Tn must be the last two digit in the entry. If Tn is not included in the entry, we use T0 as default, it means system will sent the number immediately if the number matches the entry. Example: 8[2-9]xxxxx: ： All number from 8200000 to 8899999 will be sent 24 immediately. 955xx：5 digits numbers begin with 9 will be sent immediately. 10060：Number 10060 will be sent will be immediately 22xxxxxT1：7 digits numbers begin with 22 will be sent after one second 39[3,9]xxxx ： 7 digits numbers begin with 393 or 399 will be sent immediately. 3.5.8 Call Service Settings User configure the value add service such as hotline, call forward, call transfer, call waiting, 3-way conference call, auto-answer, etc in this page。 Hotline: configure hotline number. Warm Line Time：Set waiting time for the user picking up the phone to dial hotline number, the config range is 0-9s, default is 0s. If warm line time is 0s, then hotline number will be sent right away after off-hook; If the range is 1-9s, take 3s as an example, hotline number will be sent immediately 3s later without pressing any key. As long as any key is pressed within the setting time, timer will be suspended. Auto Answer: Enable/disable auto answer function. No Disturb: DND, do not disturb, enable this option to refuse any calls. Ban Outgoing: Enable this to ban outgoing calls. 25 Enable Call Transfer: Please refer to Value_add_service for detail. Enable Call Waiting: Enable/disable Call Waiting Enable Three Way Call: Please refer to Value_add_service for detail. Accept Any Call: If this option is disabled, E103 IP refuses the incoming call when the called number is different from E103 IP’s phone number. No Answer Time: no answer call forward time setting. Black List: incoming call in these phone numbers will be refused. Limit List: outgoing calls with these phone numbers will be refused 3.5.9 Memory Key This page layout shows the number setting of Voice mail and speed-dial key. MWI Number: configure the number of picking up voicemail message key. Memory1~Memory7: configure the number of the speed dial key. If MWI Number and Memory have disposed the number, presses down the key which corresponds on the telephone board; the telephone will dial the number automatically which the key disposed. Memory Key HdActive: configure the number of the park key. In park1 mode, If a call is active on either line, press down “hold” key, execute SD HdActive, calling the user of this number. Memory Key HdIdle: configure the number of the park key. In park1 mode, If no call is active and a line is available execute SD HdIdle, after pressing down “hold” key; calling the user of this number. After call park feature is enabled, Memory Key HdActive and Memory Key HdIdle configure related parameters; you can carry out park1 function. 3.5.10 MMI Filter MMI filter is used to make access limit to E103 IP phone. When MMI filter is enable. Only IP address within the start IP and end IP can access IP phone. 26 3.5.11 DSP This page mainly completes voice configuration. CODEC: select the prefer CODEC; support ulaw, alaw, G729 and G7231 5.3/6.3 Signal Standard: Signal standard for different area. Handdown Time: Hand down detects time. Input Volume: Handset input volume. Output Volume: Handset output volume. Handfree Volume: Hand free volume G729 Payload Length: G729 payload length VAD: Enable/disable Voice Activity Detection 3.5.12 VPN This page is VPN setting page, the IP phone support the VPN with UDP and L2TP protocol .The parameters is as below VPN IP： After VPN registered successfully, VPN server will give an IP aggress 27 to the terminal. If there is a IP address shown on terminal (except for 0.0.0.0),it means your VPN has registered UDP Tunnel VPN Server Addr： Register to the address of VPN server VPN Server Port： Register to the port of VPN server Server Group ID： Group ID of UDP VPN Server Area Code： Area code of VPN server L2TP VPN Server Addr： Register to the address of VPN server VPN User Name： L2TP VPN username VPN Password： L2TP VPN password UDPTunnel: use the UDP to visit VPN L2TP: use the L2TP to visit VPN Enable VPN: Enable the VPN server, you must choose UDP or L2TP type in advance Notice: At the present, L2TP only support L2TP VPN server under Linux, UDP only support a private UDP VPN server. 3.6 Dial-Peer dial rule setting Please refer to How to use dial rule for detail. 28 3.7 Config Manage Save Config: Save current settings. Clear Config: Restore to default settings. Backup Config: Backup the config file, via point the right key of mouse-à save target as….-àwill pop a save window, then type the config file name in the File name (the file type is text file) Update Configuration: Update the current configuration through configuration files. Notice: Clearing config in admin mode, all settings restores to factory default; clear config in guest modem, all settings except sip, advance sip restore to factory default. 29 3.8 Update Firmware 3.8.1 Update Web Update： Update the application or configuration files of the phone. The application document is .z format, and the configuration file is .cfg format. Through clicking on the "browse" button to open the upgrade file or configuration file, then click on "Update" button. After the upgrade, the phone will automatically restart. Notice：When upgrading, WEB page cannot be closed. FTP Update: Upload/download the configure file with FTP or TFTP server, or download firmware from FTP or TFTP server Back up configure file to your FTP/TFTP server. Configure use .cfg extension. The Type includes two parts of config file export and config file import Config file export: export the config file Config file import: import the config file The phone phone support FTP and TFTP auto update, the gateway will auto obtain the configure file from your update server if configured. To obtain the original configure file, you can use the FTP/TFTP back up as describe above. Configure file using module structure, user may remain the concerned modules and remove other modules. Put the configure file in the root directory of update server when finish editing. 30 3.8.2 Auto Update Current Version: the system will display the current version number Server Address: FTP/TFTP server address Username: FTP server user name Password: FTP server password Config File Name: The name of configuration file Config Encrypt Key: The encrypt key of confirmation file Protocol Type: The protocol type that used for upgrading Update Interval Time: The interval time that the terminals search for new configuration file. Update Mode: auto provision mode; Disable: not auto update，Update after reboot: auto update after reboot，Update at time interval: auto update after a certain time Configure file version was in the <> Version 1.0007 and CongFile Version For instance: Gateway original version is: < >Version: 1.0000 CongFile Version：6 User may edit the configure file version to: < >Version: 1.0007 CongFile Version：7 31 3.9 System Manage 3.9.1 Account Manage Set web access account or keypad password of E103 IP. 3.9.2 Syslog config Set the system log Server IP: set the syslog server address Server Port: set the syslog server port 32 MGR Log Level: set the MGR log level SIP Log Level: set the SIP log level IAX2 Log Level: set the IAX2 log level Please click “apply” after setting 3.9.3 Phone Book 3.9.4 Time Set This page layout is the setting of time of phone. Server: type the IP address of time server Timezone: select correct time zone in list box Timeout: longest response time for SNTP Daylight: daylight saving time SNTP: select SNTP server 12 Hours Format: select 12 hours format Manual Config: time setting 33 3.9.5 MMI SET Set the greeting information on LCD. 3.9.6 Logout & Reboot Logout：Exit the Web entry. Reboot Phone：Logout the entry, and reboot the phone. When user modifies any config of the phone, it will take effect after being rebooted, you can enter into this layout and click “Reboot”. And the phone will be rebooted automatically. Note：Reboot IP phone, some setting needs to reboot to make it works. Please always save configuration before reboot, otherwise the setting will return to previous setting. 34 4. Operating Method for Dialing 4.1 How to dial IP Phone You can make a call after being made a proper setting on your phone. Please confirm whether all the net wires are connected correctly. If you want to make a call, you can make it after dialing the number and then pressing “#”. You can find IP address through the menu. Modify the IP address of the computer, and making it the same net as the phone. Inputting the IP address of E103 IP in the browser, and then you can visit the setting layout of E103 IP after pressing the Enter key; super user account is admin/admin; common user account is guest/guest. 4.2 Set the phone being connected to server 4.2.1 Set the WAN interface The connection ways of entering the NetworkàWAN Config layout phone of the net port: E103-IP could be connected to Internet by using the static IP, DHCP IP, or PPPoE dialing. As for the specific configuration please see 3.3.1 WAN Config. 35 4.2.2 SIP setting： Enter into the VoIP à SIP Config to set the layout config and sip account information: Register Server Addr: Register address of public SIP server Register Server Port: Register port of public SIP server，default port is 5060. Register Username: Username of your SIP account (Always the same as the phone number) Register Password: Password of your SIP account. Phone Number: Phone number of your SIP account ----choose Enable Register； You can dial VoIP phone when the WAN interface and IAX protocol are being set correctly. Message Waiting Indication：Set Disable/Enable message waiting through Pull-down menu, including: Disable：MWI is disabled, even if received NOTIFY message from the server indicating new voicemail, phone will not prompt.； Enable (Subscribe): MWI is enabled and SUBSCRIBE will be sent, if the server sends NOTIFY message indicating new voicemail received, MWI LED will blink to prompt. Enable(No Subscribe)：MWI is enabled, but phone will not send SUBSCRIBE, if the server sends NOTIFY message indicating new voicemail received, MWI LED will also blink to prompt. SIP1 Subscribe will still be used in config file: config option “0” means “Disable”, “1” means “Enable (Subscribe)”, “2” means “Enable (No Subscribe)”. 36 4.3 How to use the dial rule? E103-IP provide flexible dial rule, with different dial-rule configure, user can easily implement the following function: ----Replace, delete or add prefix of the dial number. ----Make direct IP to IP call ----Place the call to different servers according the prefix. You can click “Add” to add a new dial rule. Below is the detail setting of the dial-rule: Phone Number: The Number suit for this dial rule, can be set as full match or prefix match. Full match means that if the number user dialed is completely the same as this number, the call will use this dial-rule. Prefix match means that if prefix of the number that the user dials is the same as the prefix, the call will use this dial-rule, to distinguish from the full match case; you need to add “T” after the prefix number in the phone number setting. Call Mode: support SIP. Destination (optional): call destination, can be IP or domain. Default is 0.0.0.0; in this case the call will be routed to the Public SIP server. If you set the destination to 255.255.255.255, then the call will be routed to the private SIP server. Also you can key other address here to make direct IP calls Port (optional): Configure the port of the destination, default is 5060 in SIP Alias (optional): Set up the Alias. We support four Aliases as below. Alias need to co-work with the Del Length: add:xxx, add prefix to the phone number, can set to reduce the dial length. All: xxx, replace the phone number with the xxx, can use as speed dial function. Del: delete the first N numbers. N is set in the Del Length rep:xxx，replace the first N numbers. N is set in the Del Length. For Example: User wants to place a call 86633-8215555, then can set the phone number in the dial rule as 0633T, and set the Alias as rep: 86633, and set the Del Length to 4. Then all calls begin with 0633 will be changed to 86633 xxxxxxxx. Suffix (optional): Configure suffix, show no suffix if not set 37 Instance: 2T rule: If the call starts with 2, the first 2 will be deleted, and the rest number will be sent to private SIP server. 3T rule: If the call starts with 3, the first 3 will be deleted, and the rest number with be sent to public SIP server. 123 rule: Dial 123 and will send 06332221015 to your server. It is used as speed dial function. 0T rule: If the call begins with 0, the first 0 will be replaced by 86. It means that if you dial 06332221015 and AG-188 will send 866332221015 to your server. 11 rule: when you dial 11, the call with send to 192.168.0.11, suit for LAN application without set up a sip server. 4.4 Voice mail When there are new messages, the MWI will give out prompt according to the options of "Message Waiting Indication" in web page layout. If “Disable” is selected, MWI function is disabled, even if received NOTIFY message from the server indicating new voicemail, phone will not prompt; If “Enable (Subscribe)” is selected, MWI function is enabled and Subscribe will be sent, if the server sends NOTIFY message indicating new voicemail received, MWI LED will blink to prompt; If “Enable (No Subscribe)” is selected, MWI is enabled, but Subscribe will not be sent, if the server sends NOTIFY message indicating new voicemail received, 38 MWI LED will also blink to prompt. After the voicemails are picked-up, MWI LED will stop blinking. 39 IC Warning: This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) This device may not cause interference, and (2) this device must accept any interference, including interference that may cause under operation of the device. Privacy of communications may not be ensured when using this telephone. Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication. FCC Caution: Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC Radiation Exposure Statement: The base complies with FCC radiation exposure limits set forth for uncontrolled environment. The base should be installed and operated with minimum distance 20cm between the radiator& your body. The handset compliances with the RF Exposure Evaluation. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: ---Reorient or relocate the receiving antenna. ---Increase the separation between the equipment and receiver. ---Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. ---Consult the dealer or an experienced radio/TV technician for help.
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : No Author : Administrator Create Date : 2011:09:09 10:41:56+08:00 Modify Date : 2012:04:19 17:51:12+08:00 Has XFA : No XMP Toolkit : Adobe XMP Core 4.2.1-c041 52.342996, 2008/05/07-20:48:00 Creator Tool : pdfFactory Pro www.fineprint.cn Metadata Date : 2012:04:19 17:51:12+08:00 Format : application/pdf Creator : Administrator Title : E103-IP user manual-v1.0.doc Producer : pdfFactory Pro 3.17 (Windows XP Professional Chinese) Document ID : uuid:9f857cc3-def6-4fa5-994c-d631882ffe33 Instance ID : uuid:370db9e7-c990-49e5-b17a-9b0b9f7f3dba Page Count : 41EXIF Metadata provided by EXIF.tools