CHANG SHIN INFOTEL SG-2200 Access Controlled security system with Zigbee & RFID User Manual

CHANG SHIN INFOTEL CO.,LTD Access Controlled security system with Zigbee & RFID

User Manual

S G - 2 2 0 0User’s  manual
Contents1. Administrators  card  registration1.1. Administrators  card  registration.2. User  administration.2.1. User  administration
User  ManualSG-22001  Administrators  card  registration              1.1  Administrators  card  registration                -  Administrator  card  is  used  when  a  user  registered  in  the  SG-2200.                -  Registration  procedure  is  shown  in  [Table  1]        No.Description1Check  if  the  green,  blue  and  red  LED  emit  light  in  sequence,  after  the  terminal installed.2If confirmmed, tag  the administrators  RFID card  in the box on  the device.3When  the  green LED  is emitting,  the registeration is successful.[Table  1]  Administrators  card  registration  procedure                -  The  administrator  card  is  used  for  the  purpose  of  registration.                -  Administrator  card  can  apply  for  only  one  card  when  the  stand  alone.
User  Manual2  User  administration                2.1  User  Registration                -  Registration  procedure  [Table  2]        No.Description1Tagging  an  administrator  card  is  just  a  RFID  card  user  registration  status.2Make  sure  that  the  green  LED  is  blinking.3RFID  card  registration  1)  When  tagging  your  RFID  card,  the  LED  is  turned  to  blue  and  back  to green  blinking.  2)  once  more  tagging  to  the  administrator  card  for  the  final  registration.� If the ID is registered successfully, the LED is blinking momentarily changed to blue  and back to green.� When lead to problems with registration ID is shown in red, it LED blinking returns to green.4W-Key  registration  1)  When  tagging  your  W-key  card,  the  LED  is  turned  to  blue  and  back  to green  blinking.  2)  once  more  tagging  to  the  administrator  card  for  the  final  registration.� If the ID is registered successfully, the LED  is blinking momentarily  changed to blue and back to green.� When lead to problems with registration ID is shown in red, it LED blinking returns to green.[Table  2]  User  registration  orderIf  you  have  a  problem  during  registrationWait a  while and do nothing, blinking green and escaped from  the ID registration process ends. If  you  start  by  tagging  an  administrator  card,  ID  registration  is  available.
User  Manual3  Rule          3.  1.  FCC  RuleFederal  Communications  Commission  (FCC)  Statement Caution Changes  or  modifications  not  expressly  approved  by  the  part  responsible  for  compliance could  void  the  user’s  authority  to  operate  the  equipment.WarningThis  device  complies  with  Part  15  of  the  FCC  Rules.Operation  is  subject  to  the  following  two  conditions:       1)  this  device  may  not  cause  interference  and       2)  this  device  must  accept  any  interference,  including  interference  that  may  cause  undesired       operation  of  the  device.Information  to  User  This  equipment  has  been  tested  and  found  to  comply  with  the  limits  for  a  Class  B  digital device,  pursuant  to  part  15  of  the  FCC  rules.  These  limits  are  designed  to  provide  reasonable protection  against  harmful  interference  in  a  residential  installation.  This  equipment  generates, uses  and  can  radiate  radio  frequency  energy  and,  if  not  installed  and  used  in  accordance with the instructions, may  cause  harmful  interference to  radio  communications.  However,  there is  no  guarantee  that  interference  will  not  occur  in  a  particular  installation.  If  this  equipment does  cause  harmful  interference  to  radio  or  television  reception,  which  can  be  determined  by turning  the  equipment  off  and  on,  the  user  is  encouraged  to  try  to  correct  the  interference  by one  or  more  of  the  following  measures:     •  Reorient  or  relocate  the  receiving  antenna.     •  Increase  the  separation  between  the  equipment  and  receiver.     •  Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.    •  Consult  the  dealer  or  an  experienced  radio/TV  technician  for  help.This  appliance  and  its  antenna  must  not  be  co-located  or  operation  in  conjunction  with  any other  antenna  or  transmitter.A  minimum  separation  distance  of  20  ㎝  must  be  maintained  between  the  antenna  and  the person  for  this  appliance  to  satisfy  the  RF  exposure  requirements.

Navigation menu