CHANG SHIN INFOTEL SG-2200 Access Controlled security system with Zigbee & RFID User Manual

Download:
Mirror Download [FCC.gov]
Document ID	2841601
Application ID	J+zdna87MJb8uI102OqMMA==
Document Description	User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	6.42kB (80200 bits)
Date Submitted	2015-12-14 00:00:00
Date Available	2015-12-14 00:00:00
Creation Date	2015-12-11 11:31:57
Producing Software	Hancom PDF 1.3.0.433
Document Lastmod	2015-12-11 11:31:57
Document Title	User Manual
Document Creator	Hancom PDF 1.3.0.433
Document Author:	Park

SG-2200
User’s manual
Contents
1.
Administrators card registration
1.1.
2.
Administrators card registration.
User administration.
2.1.
User administration
User Manual
SG-2200
1 Administrators card registration
1.1
Administrators card registration
- Administrator card is used when a user registered in the SG-2200.
- Registration procedure is shown in [Table 1]
[Table 1] Administrators card registration procedure
No.
Description
Check if the green, blue and red LED emit light in sequence, after the terminal
installed.
If confirmmed, tag the administrators RFID card in the box on the device.
When the green LED is emitting, the registeration is successful.
- The administrator card is used for the purpose of registration.
- Administrator card can apply for only one card when the stand alone.
User Manual
2 User administration
2.1
User Registration
- Registration procedure [Table 2]
[Table 2] User registration order
No.
Description
Tagging an administrator card is just a RFID card user registration status.
Make sure that the green LED is blinking.
RFID card registration
1) When tagging your RFID card, the LED is turned to blue and back to
green blinking.
2) once more tagging to the administrator card for the final registration.
�If the ID is registered successfully, the LED is blinking momentarily changed to blue and back to green.
�When lead to problems with registration ID is shown in red, it LED blinking returns to green.
W-Key registration
1) When tagging your W-key card, the LED is turned to blue and back to
green blinking.
2) once more tagging to the administrator card for the final registration.
�If the ID is registered successfully, the LED is blinking momentarily changed to blue and back to green.
�When lead to problems with registration ID is shown in red, it LED blinking returns to green.
If you have a problem during registration
Wait a while and do nothing, blinking green and escaped from the ID registration process ends.
If you start by tagging an administrator card, ID registration is available.
User Manual
3 Rule
3. 1. FCC Rule
Federal Communications Commission (FCC) Statement
Caution
Changes or modifications not expressly approved by the part responsible for compliance
could void the user’s authority to operate the equipment.
Warning
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
1) this device may not cause interference and
2) this device must accept any interference, including interference that may cause undesired
operation of the device.
Information to User
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio communications. However, there
is no guarantee that interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
This appliance and its antenna must not be co-located or operation in conjunction with any
other antenna or transmitter.
A minimum separation distance of 20 ㎝ must be maintained between the antenna and the
person for this appliance to satisfy the RF exposure requirements.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
Linearized                      : No
Page Count                      : 5
Tagged PDF                      : No
Language                        : ko-KR
Page Layout                     : SinglePage
XMP Toolkit                     : Adobe XMP Core 4.0-c316 44.253921, Sun Oct 01 2006 17:14:39
PDF Version                     : 1.4
Producer                        : Hancom PDF 1.3.0.433
Creator Tool                    : Hancom PDF 1.3.0.433
Create Date                     : 2015:12:11 11:31:57+09:00
Modify Date                     : 2015:12:11 11:31:57+09:00
Metadata Date                   : 2015:12:11 11:31:57+09:00
Format                          : application/pdf
Creator                         : Park
Date                            : 2015:12:11 11:31:57+09:00
Document ID                     : 585A6D25-4252-441E-9110-CBDBB7FCFBAA
Instance ID                     : uuid:0A401F71-EB3F-43D0-AAAB-0C29CAE302DB
Part                            : 1
Conformance                     : B
Author                          : Park

EXIF Metadata provided by EXIF.tools